TITLE
BIDI-155F2J1
DATE:
2002.11.20
WRITTEN CHECKED APPROVED DOCUMENT NO: REV:
S.J. Chang
Yuhong Shih
Y.Y Tsai S1
DELTA ELECTRONICS, INC.
155Mbps 1X9 SC Bi-Directional Transceiver Module for ATM,
SONET OC-3/SDH STM-1,Fast Ethernet
BIDI-155F2J1
Feature
zIndustry Standard 1 x 9 Footprint
zCompliant with existing standards
zSingle +3.3 V Power Supply
zPECL Differential Inputs and Outputs
zWave Solderable and Aqueous Washable
zClass 1 Laser International Safety Standard IEC 825 Compliant
zBIDI-155Exxx series TX 1310nm /RX 1550nm;
BIDI-155Fxxx series TX 1550nm /RX 1310nm
zBIDI-155xxx1 series indicate for SC Receptacle;
BIDI-155xxx3 series indicate for SC Pigtail ;
BIDI-155xxx6 series indicate for MU Pigtail
Applications
zSONET/SDH Equipment Interconnect
zWDM Application
z100Base Fast Ethernet
z155Mbps ATM
Absolute Maximum Ratings
Parameter Symbol Min. Typ. Max. Unit Reference
Storage temperature Ts -40 85 ℃
Lead Soldering
Temperature
TSOLD 260
℃
Lead Soldering Time tSOLD 10 sec.
Supply Voltage Vcc 0 5 V
Bit Rate 10 155.52 Mbit/s
Recommended Operating Conditions
Parameter Symbol Min. Typ. Max. Unit Reference
Ambient Operating
Temperature
TA 0 70
℃
Supply Voltage Vcc 3.135 3.3 3.465 V
Humidity (without dew) 10 95 %
Data Differential Input
Voltage Amplitude 300 mV Note
Data Output Load RDL 50
Ω
Note: When VDC is 2V and VCC is 3.3V
TITLE
BIDI-155F2J1
DATE:
2002.11.20
WRITTEN CHECKED APPROVED DOCUMENT NO: REV:
S.J. Chang
Yuhong Shih
Y.Y Tsai S1
DELTA ELECTRONICS, INC.
155Mbps 1X9 SC Bi-Directional Transceiver Module for ATM,
SONET OC-3/SDH STM-1,Fast Ethernet
BIDI-155F2J1
Transmitter Electro-Optical Performance Specifications
Parameter Symbol Min. Typ. Max. Unit Reference
Supply current Icc A mA Note (1)
Data input
voltage-Low VIL- VCC -1.810 -1.475 V
Data input
voltage-High VIH- VCC -1.165 -0.880 V
Launched power
(avg.) Po -15 -11 -8 dBm Note (2)
Optical extinction
ratio 8.2 dB Note (2)
Center wavelength λc 1500 1550 1600 nm
Spectral width (RMS) σ 3 nm rms
Optical risetime tr 1.3 ns Note (3)
Optical falltime tf 1.3 ns Note (3)
Output Eye Compliant with Bellcore TR-NWT-000253 and ITU recommendation G.957
Note (1). A (TX)+ B (RX) = 230mA (A: Not include termination circuit)
Note (2). Launched power (avg.) is power coupled into a single mode fiber.
Note (3). These are 20-80% values.
Mask of the eye diagram for the optical transmit signal
0.85
1.20
0.80
1.00
0.50
0.20
0.00
-0.20
Amplitude
0.350.150.00
Time
0.65
Mean level of logical "0"
1.00
Mean level of logical "1"
Optical Pulse Mask with Bessel Filter Specified in ITU-T G.957
TITLE
BIDI-155F2J1
DATE:
2002.11.20
WRITTEN CHECKED APPROVED DOCUMENT NO: REV:
S.J. Chang
Yuhong Shih
Y.Y Tsai S1
DELTA ELECTRONICS, INC.
155Mbps 1X9 SC Bi-Directional Transceiver Module for ATM,
SONET OC-3/SDH STM-1,Fast Ethernet
BIDI-155F2J1
Receiver Electro-Optical Performance Specifications:
Parameter Symbol Min. Max. Unit Reference
Supply current Icc B mA Note (1)
Data output
voltage-Low VOL- VCC -1.810 -1.620 V
Data output
voltage-High VOH- VCC -1.025 -0.880 V
Signal Detect output
voltage-Low VOL- VCC -1.860 -1.620 V
Signal Detect output
voltage-High VOH- VCC -1.080 -0.880 V
Optical input
sensitivity PIN -30 dBm Note (2)
Optical input
saturation (Overload) PSAT -7.5 dBm Note (2)
Signal detect- Assert PA -31 dBm
Signal detect-
Deassert PD -45 dBm Note (3)
Optical wavelength λ 1260 1310 1360 nm
S/X Endurance 10 dB Note (4)
Optical isolation 25 dB Note (5)
Note (1). A (TX) + B (RX) = 230mA (B: using a resister of 150Ω between Data-output and ground).
Note (2). With BER better than or equal to 1x10-10, measured in the center of the eye opening
with 223-1 NRZ PRBS
Note (3). When SD deasserted, the data output is Low-level (fixed)
Note (4). X=10 MHz, Rectangular BER =10-10
Note (5). Receiver isolation between 1500nm ~1600nm
TITLE
BIDI-155F2J1
DATE:
2002.11.20
WRITTEN CHECKED APPROVED DOCUMENT NO: REV:
S.J. Chang
Yuhong Shih
Y.Y Tsai S1
DELTA ELECTRONICS, INC.
155Mbps 1X9 SC Bi-Directional Transceiver Module for ATM,
SONET OC-3/SDH STM-1,Fast Ethernet
BIDI-155F2J1
Recommended Circuit Schematic
Laser
Driver
LIMITING
A mp lifie r
Serializer/
Deserializer
ECL/PECL
DRIVER
Receiver
PLL etc.
VCC
TX+
TX-
RD-
RD+
VCC SerDes
3.3V
TXGND
TxD
TxD
VCCRx
VCC SerDes
3.3V
Pre-
Amp
SD
RxD
RxD
RxGND
VCCTx
Delta Transceiver
C2
C1 L2
L1
Signal detect
SD to upper level
R13
R12
R9
R10
R11
R6
R5
R3
R4 R2
R1
R7
R8
C3
C6
C7
C4
C5
1
2
3
4
5
6
7
8
9
C1/2/3 = 4.7 uF
C4/5/6/7 = 100 nF
L1/2 = 1 uH
R1/2 =82 Ω(If C4/5=0, then R1/2 =130 Ω)
R3/4 =130 Ω(If C4/5=0, then R3/4 =82 Ω)
R7/8 =150 Ω
R5/6/9/10/11/12 Depend on SerDes chip used
R13 = 270 Ω
Value of R5/6/9/10/11/12 may vary as long as proper 50 Ωtermination or 100 Ωdifferential
is provided. For good EMI performance, the power supply filter is required.Use short tracks
from the inductor L1/2 to the module VccTx/VccRx .
TITLE
BIDI-155F2J1
DATE:
2002.11.20
WRITTEN CHECKED APPROVED DOCUMENT NO: REV:
S.J. Chang
Yuhong Shih
Y.Y Tsai S1
DELTA ELECTRONICS, INC.
155Mbps 1X9 SC Bi-Directional Transceiver Module for ATM,
SONET OC-3/SDH STM-1,Fast Ethernet
BIDI-155F2J1
Mechanical Dimensions
LASER SAFETY
This single mode transceiver is a Class 1 laser product. It complies with IEC 825 and FDA 21 CFR 1040.10
and 1040.11. The transceiver must be operated within the specified temperature and voltage limits. The
optical ports of the module shall be terminated with an optical connector or with a dust plug.
TITLE
BIDI-155F2J1
DATE:
2002.11.20
WRITTEN CHECKED APPROVED DOCUMENT NO: REV:
S.J. Chang
Yuhong Shih
Y.Y Tsai S1
DELTA ELECTRONICS, INC.
155Mbps 1X9 SC Bi-Directional Transceiver Module for ATM,
SONET OC-3/SDH STM-1,Fast Ethernet
BIDI-155F2J1
Regulatory Compliance
Test Item Reference Qty’ Evaluation
(#1)
Electromagnetic Interference
EMI
FCC Class B
EN 55022 Class B
CISPR 22
5
(#2) Immunity：
Radio Frequency
Electromagnetic Field
EN 61000-4-3
IEC 1000-4-3
5
(#3) Immunity：
Electrostatic Discharge to
the Duplex SC Receptacle
EN 61000-4-2
IEC 1000-4-2
IEC 801.2
5
(#4) Electrostatic Discharge
to the Electrical Pins
MIL-STD-883C
Method 3015.4
EIAJ#1988.3.2B
Version 2,
Machine model
5
(1) Satisfied with electrical
characteristics of product
spec.
(2) No physical damage
