CWR-134-14-0001 - CW Industries

•130 James Way, Southampton, PA 18966 - 3838 •Telephone: (215) 355-7080 •Fax: (215) 355-1088 •www.cwind.com

DIP Connectors

The CW Dual-In-Line Plug (DIP) connector is used for rapid, permanent connection

of ribbon cable to a PC board or to a standard DIP socket when connect/disconnect

capabilities are required. The cover is factory preassembled to the connector base to

simplify assembly to cable and has ridges for cable alignment. CW DIP connectors

are Mil-DTL-83503/6 approved.

•Beveled corner on cover and base

at pin #1 provides orientation and

contact identification.

•No alignment tools required.

Cable fits snugly between base’s

cover-support posts, and is guided

into position by ridges molded into

inner surface of cover.

•No special cable preparation

required. Factory preassembled

cover minimizes assembly time.

Cable is inserted and terminated in

one simple step.

•No “bare shoulders”. No exposure

of unnecessary sections of the

contact and possible shorting at the

PC board interface.

•Sturdy terminal posts are strong,

yet flexible enough to withstand

occasional bending and

straightening without fatigue.

•130 James Way, Southampton, PA 18966 - 3838 •Telephone: (215) 355-7080 •Fax: (215) 355-1088 •www.cwind.com

DIP Connectors

Con tact

•Patented offset tines

produce Torq-Tite™

termination for added

reliability.

•Double barbs bite into

plastic, retaining contact

firmly in insulator.

•Spring-temper phosphor

bronze contact material

resists breakage

during bending or

straightening

operations.

•Two tail lengths are

available for use with

standard or low profile

DIP sockets. .012 in. x

.021 in. contact cross-

section provides proper

mating with a variety of

DIP sockets.

DIP Connector Features

•Mil-DTL-83503/6 approved

•One-piece construction.

•14, 16, 24,and 40 pin versions.

•Patented Torq-Tite™ contacts, ensure reliable gas-tight

terminations.

•Gold-plated phosphor bronze contacts, standard tin-lead

plated contacts optional.

•Accepts 28-30 AWG stranded or solid conductors.

•Simple assembly – bench press or low cost hand tool is all that’s

needed for terminating cable and connectors.

•All pin numbers clearly marked and legible before and after

assembly. Numbering is arranged to meet MIL-DTL-83503

specifications for standard IC DIP numbering.

•Optional strain relief clips are easily installed. Allows top center,

vertical cable routing to reduce possibility of damage to contact

pins during removal of DIP from socket.

•Two contact tail lengths available — .175 in. standard or optional

130 in. length for mating with low profile Dip Sockets.

Strain Relief

Optional metal strain relief straps are available.

Connection is isolated from mechanical strain

by the bend in the cable, as it is folded over

the top of the assembled connector. The Strain

Relief Strap is placed over the cable and

snaps into a recess on the connector. A

centralized top cable exit is created in the

finished cable assembly.

Contact Identification

Every contact position is numbered, per Mil-

DTL-83503, for easy identification. In addition,

a beveled corner at pin #1 enhances

orientation of the connector to the mating DIP

Socket, even in blind installations.

Assembly

The CT200 DIP Hand Tool is designed to

terminate out 14 and 16 pin DIP Connectors. It

is easy to use, lightweight and compact,

making it an ideal tool for field replacement

work or low volume assembly applications. DIP

connectors can also be assembled to cable

using CW’s CT301 76/84 Bench Press.

•130 James Way, Southampton, PA 18966 - 3838 •Telephone: (215) 355-7080 •Fax: (215) 355-1088 •www.cwind.com

14/16 Pin DIP Connector

24 Pin DIP Connector

40 Pin DIP Connector

DIP Connectors

Dimensions

Engineering Dimensions

PAT. 3,993,393

13 15

14 16 19

18 21

20 23

22 24

12 10

11 8

CONTACT

TAIL LENGTH

(9.1)

(2.54)

STRAIN RELIEF

STRAP-OPTIONAL

.100

(33.5)

(27.94)

TYP.

.36

1.264±.010

(32.1±.25)

NOTCHED CORNER ORIENTS

No. 1 CONTACT LOCATION.

TYP.

CONNECTOR COVER SHOWN

IN OPEN POSITION.

IN CLOSED POSITION.

.248

(6.30)

(.30)

(15.24)

(8.8)

.012

.35

(18.3)

.021

(.54) TYP.

(±.25)

±.010

1.100

1.32

.600

.72

PAT. 3,993,393

21 23

20 18

24 26 29

28 30 34

31 32 33 36

35 37

1016 15 14 12

13 11 97

39 40

.100

STRAP-OPTIONAL

(2.54)

STRAIN RELIEF

(9.1)

TYP.

(18.3)

CONNECTOR COVER SHOWN

IN OPEN POSITION.

(15.24)

IN CLOSED POSITION.

CONNECTOR COVER SHOWN

No. 1 CONTACT LOCATION.

NOTCHED CORNER ORIENTS

(52.50±.25)

(48.26)

TYP.

(.54)

.021

(53.9)

TYP.

(.30)

CONTACT

TAIL LENGTH

(6.30)

.248

.012

.35

(8.8)

(±.25)

±.010

2.067±.010

.36

1.900

.600

2.12

.72

PAT. 3,993,393

7654321

8910 11 12 13 14

AVAILABLE WITH 16 POSITIONS.)

(14 CONTACT POSITIONS SHOWN, ALSO

(8.1)

.32

STRAP-OPTIONAL

STRAIN RELIEF

(10.7)

IN CLOSED POSITION.

IN OPEN POSITION.

CONNECTOR COVER SHOWN

(±.25)

±.010

(6.30)

.248

.34

(8.6)

.012

(7.62)

(.30)

TYP.

NOTCHED CORNER ORIENTS

No. 1 CONTACT LOCATION.

(±.25)

.100

(2.54) TYP.

±.010

(.54)

.021 TYP.

CONNECTOR DIMENSIONS

NO. OF

CONTACTS

ABC

.60

(15.2) (19.2)

.754 (20.6)

.81

.854

(17.8)

.70 (21.7) (23.1)

.91

TAIL LENGTH

CONTACT

.300

.42

•130 James Way, Southampton, PA 18966 - 3838 •Telephone: (215) 355-7080 •Fax: (215) 355-1088 •www.cwind.com

Final assembly length “L”

1=3”+1/8”

2=6”+1/8”

3=12”+1/4”

4=24”+1/4”

5=48”+1/4”

CA-XX-910X

Number of Conductors

(14, 16, 24 or 40)

CWN-SR-XX

EXAMPLE: Strain Relief

Strap part number for

24-pin DIP Connector

is CWN-SR-24

DIP Connectors

• Contacts: phosphor bronze standard.

• Contact Plating: 10µ in. gold over 50µ in. nickel, standard;

30µ in. gold over 50µ in. nickel, optional; 50µ in. gold over

50µ in. nickel, optional; 100µ in. tin-lead optional

• Insulator Material: UL 94V-0 flame - retardant glass filled

thermoplastic

• Strain Relief Strap Material: tin-plated steel

• Color: blue

• Operating temperature: -55ºC to +125ºC

• Current Rating: 1A (maximum) per contact

• Dielectric Withstand Voltage: Greater than 500 Vdc at

sea level

• Insulation Resistance: Greater than 5 x 109ohms

• Mates with .050 in. centered round conductor flat cable

and standard DIP socket with .100 in. x .300 in. or .100 in.

x .600 in. contact spacing

• Cover pull off force, with strain relief 20 lb minimum (force

along contacts’ primary axes)

How to Order DIP Connectors

Specifications and Ordering Information

Specifications

CWR-XXX-XX-XXXX

Type of Connector

Standard tail length .175” = 130

Optional tail length .130” = 134

Number of Contacts

(14, 16, 24 or 40)

Plating

0000=10µ in. gold over 50µ in.

nickel (standard)

0001=30µ in. gold over 50µ in.

nickel

0002=50µ in. gold over 50µ in.

nickel Mil-DTL-83503/6

approved. (CWR-130-14,

16, 24 only)

0003=100µ in. tin-lead

EXAMPLE: CWR-130-16-0002 is part number for a 16-pin DIP connector

with .175 in. tails and 50µ in. gold over 50µ in. nickel contacts

How to Order DIP Cable Assemblies

Cable assemblies with two DIP connectors (CWR-130-XX-0000)

on a prescribed length of color-coded cable are available with

connectors oriented per drawing 31-1. (#1 contacts oriented to

brown conductor.)

For other lengths, orientations, numbers or combinations of

connectors, contact the factory or your local value-added distributor.

DRAWING 31-1

BROWN (No. 1 Cond.)

How to Order Strain Relief Straps for DIP Connectors

Connector Size

(14, 16, 24 or 40)

(14 and 16)

(24 and 40)