Document Number: 42020 For technical questions, contact: spresale@vishay.com www.vishay.com
Revision: 13-Feb-07 25
Type 716P
Vishay Sprague
Polypropylene Film Capacitors
High Performance, ORANGE DROP®
Type 716P ORANGE DROP® is a high
performance version of the popular Type 715P. It
is made from polyproplyene and foil with copper
leads for the ultimate in high pulse current and high
rms current capabillity. It is a pressed unit for better
utilization of board space.
The 200 V, 400 V and 600 V ratings are single section,
extended foil units allowing for high frequency, high current
applications. The 800 V, 1200 V and 1600 V ratings are
series-wound extended foil with a floating metalized common
foil with provides self-healing characteristics in addition to
high frequency, high current capabilities.
Capacitance change with temperature is less than 3 % over
the entire operating temperature range. The temperature
coefficient is negative and virtually linear at 180 ppm/°C over
the temperature range of + 25 °C to + 105 °C. This
characteristics means the Type 716P is suitable for matching
with positive TC resistors and inductors to maintain circuit
stability.
Type 716P ORANGE DROP® capacitors are conformally
coated with a flame retardant epoxy.
PERFORMANCE CHARACTERISTICS
Operating Temperature: - 55 °C to + 85 °C, standard;
+ 105 °C provided working voltage is reduced to 50 % of
+ 85 °C rating
Insulation Resistance: After a 2 minute charge at rated
voltage or 500 V, whichever is less
At + 25 °C: 400 000 Megohm for C ≤ 0.5 Microfarads
200 000 Megohm - Microfarads for C > 0.5 Microfarads
At + 85 °C: 20 000 Megohm for C ≤ 0.5 Microfarads
10000 Megohm - Microfarads for C > 0.5 Microfarads
At + 105 °C: 2000 Megohm for C ≤ 0.5 Microfarads
1000 Megohm - Microfarads for C > 0.5 Microfarads
Capacitance, Tolerance and Dissipation Factor:
Capacitors shall be measured at a frequency of 1000 Hz at
+ 25 °C or else be referred to measurements made at that
frequency and temperature. The maximum dissipation factor
is 0.1 %.
Dielectric Withstanding Voltage:
Capacitors rated below 1000 volts shall withstand a DC
potential of 250 % of rated voltage applied between terminals
for not more than 5 seconds.
Capacitors rated 1000 volts and above shall withstand a DC
potential of 200 % of rated voltage applied between the
terminals for not more than 5 seconds. The test voltage must
be applied and discharged through a resistor of 1 ohm per
volt.
Humidity Test: Condition capacitors with no voltage applied
for 72 hours at 95 % relative humidity and 75 °C. Remove
capaitors from humidity chamber, wipe surface dry of
moisture and dry in circulating air for 4 hours. Measure
insulation resistance after a 2 minute charge at + 25 °C and
rated voltage or 500 VDC, whichever is less. Minimum
product of insulation resistance and capacitance shall be
50 000 Megohm - Microfarads after test but need not exceed
100 000 Megohm. Not more than one failure in 12 units
tested shall be permitted.
DC Life Test: Capacitors are capable of withstanding a
500 hour life test at + 85 °C at 150 % or rated working
voltage. After test, capacitance shall not have changed by
more than 5 % of initial value, insulation resistance shall not
have decreased by more than 50 % of the initial limit and
dissipation factor shall not have increased to more than
0.1 %.
AC Life Test: Capacitors shall withstand the maximum
60 Hz voltage for a period of 500 hours at + 85 °C.
Not more than one failure allowed in 12 units tested.
RoHS
COMPLIANT
Rated DC Voltage Maximum 60 HZ Voltage
200 155
400, 600 200
800, 1200, 1600 500
www.vishay.com For technical questions, contact: spresale@vishay.com Document Number: 42020
26 Revision: 13-Feb-07
Type 716P
Vishay Sprague Polypropylene Film Capacitors
High Performance, ORANGE DROP®
DIMENSIONS in inches [millimeters]
L
Max.
S
± 0.060 [1.524]
L
Max.
S
± 0.030 [0.762]
Lead
Length
L
Max.
S
± 0.030 [0.762]
T Max.
Lead
Length
H
Max.
Terminal B
Terminal A Terminal D
1.250
[31.750]
Min.
0.250
[6.350]
Max.
0.250
[6.350]
Max.
0.250
[6.350]
Max.
Tinned Copper
d
DIMENSIONS in inches [millimeters]
CASE
CODE
L
(Max.)
S
Terminal A Terminal B Terminal D
J 0.70 [17.78] 0.500 [12.70] 0.500 [12.70] 0.375 [9.52]
K 0.95 [24.13] 0.688 [17.48] 0.688 [17.48] 0.375 [9.52]
L 1.25 [31.75] 1.031 [26.19] 0.969 [24.61] 0.719 [18.26]
M 1.70 [43.18] 1.406 [35.71] 1.344 [34.14] 1.094 [27.79]
PERFORMANCE CHARACTERISTICS
1000
5
2
155
100
5
2
10
smr
-
STLOV
1 2 5 10 2 5 100 2 5 1000
FREQUENCY - kHz
200 V
0.01 µF
0.047
0.1 µF
0.18 µF
0.56 µF
1.0 µF
102
5
2
103
5
2
104
NAT ??
?
?
?
1 2 5 10 2 5 100 2 5 1000
FREQUENCY - kHz
TYPICAL
- 55 - 50 - 25 0 + 25 + 50 + 75 + 85 + 100 + 105 + 125
TEMPERATURE DEG. CENTIGRADE
0.075
0.05
0.025
0
NOITAPISSID TNECREP
zH0001 - ROTCAF
TYPICAL
+ 2
+ 1
0
- 1
- 2
- 55 - 50 - 25 0 + 25 + 50 + 75 + 85 + 100 + 105 + 125
TEMPERATURE DEG. CENTIGRADE
TYPICAL
ECNATICAPAC TNECREP
zH0001 - EGNAHC
1 2 5 10 2 5 100 2 5 1000
FREQUENCY - kHz
1000
5
200
100
5
2
10
smr -
STLOV
400 V
0.015 µF
0.047 µF
0.1 µF
0.27 µF
0.47 µF
0.0039 µF
Type 716P
Polypropylene Film Capacitors
High Performance, ORANGE DROP®Vishay Sprague
Document Number: 42020 For technical questions, contact: spresale@vishay.com www.vishay.com
Revision: 13-Feb-07 27
PERFORMANCE CHARACTERISTICS
1000
5
200
100
5
2
10
smr
- STLOV
600 V
0.001
µ
F
0.047
µ
F
0.0056
µ
F
0.015
µ
F
0.12
µ
F
0.22
µ
F
1 2 5 10 2 5 100 2 5 1000
FREQUENCY - kHz
1000
450
2
100
5
2
10
smr - STLOV
1 2 5 10 2 5 100 2 5 1000
FREQUENCY - kHz
800 V
0.015
µ
F
0.047
µ
F
0.14
µ
F
0.0056
µ
F
0.082µF
1000
475
200
100
5
2
10
1 2 5 10 2 5 100 2 5 1000
FREQUENCY - kHz
smr - STLOV
1200 V
1600 V
1000
500
2
100
5
2
10
smr -
STLOV
1 2 5 10 2 5 100 2 5 1000
FREQUENCY - kHz
0.0027
µ
F
0.0068
µ
F
0.015
µ
F
0.056
µ
F
0.033
µ
F
0.015
µ
F
0.033
µ
F
0.001
µ
F
0.0033
µ
F
0.0082
µ
F
www.vishay.com For technical questions, contact: spresale@vishay.com Document Number: 42020
28 Revision: 13-Feb-07
Type 716P
Vishay Sprague Polypropylene Film Capacitors
High Performance, ORANGE DROP®
* These standard ratings are available through Sprague® distribution on special order. For complete Part Number, add letter and number for
terminal and lead length (Ex. 716P103916LD3).
** 60 Hz rms
STANDARD RATINGS* in inches [millimeters]
µF
± 10 % TOLERANCE PART NUMBER SIZE
LTH d
200 VDC/155 VAC**
0.010 716P10392J 0.70 [17.78] 0.25 [6.35] 0.37 [9.40] 0.032 [0.813]
0.012 716P12392J 0.70 [17.78] 0.27 [6.86] 0.39 [9.91] 0.032 [0.813]
0.015 716P15392J 0.70 [17.78] 0.26 [6.60] 0.45 [11.43] 0.032 [0.813]
0.018 716P18392J 0.70 [17.78] 0.25 [6.35] 0.45 [11.43] 0.032 [0.813]
0.022 716P22392J 0.70 [17.78] 0.27 [6.86] 0.46 [11.68] 0.032 [0.813]
0.027 716P27392J 0.70 [17.78] 0.29 [7.37] 0.48 [12.19] 0.032 [0.813]
0.033 716P33392J 0.70 [17.78] 0.32 [8.13] 0.51 [12.95] 0.032 [0.813]
0.039 716P39392J 0.70 [17.78] 0.32 [8.13] 0.56 [14.22] 0.032 [0.813]
0.047 716P47392J 0.70 [17.78] 0.34 [8.64] 0.58 [14.73] 0.032 [0.813]
0.056 716P56392K 0.95 [24.13] 0.30 [7.62] 0.55 [13.97] 0.032 [0.813]
0.068 716P68392K 0.95 [24.13] 0.33 [8.38] 0.57 [14.48] 0.032 [0.813]
0.082 716P82392K 0.95 [24.13] 0.36 [9.14] 0.60 [15.24] 0.032 [0.813]
0.10 716P10492K 0.95 [24.13] 0.39 [9.91] 0.63 [16.00] 0.032 [0.813]
0.12 716P12492K 0.95 [24.13] 0.40 [10.16] 0.69 [17.53] 0.032 [0.813]
0.15 716P15492K 0.95 [24.13] 0.45 [11.43] 0.73 [18.54] 0.032 [0.813]
0.18 716P18492L 1.25 [31.75] 0.39 [9.91] 0.67 [17.02] 0.040 [1.016]
0.22 716P22492L 1.25 [31.75] 0.43 [10.92] 0.71 [18.03] 0.040 [1.016]
0.27 716P27492L 1.25 [31.75] 0.47 [11.94] 0.75 [19.05] 0.040 [1.016]
0.33 716P33492L 1.25 [31.75] 0.47 [11.94] 0.86 [21.84] 0.040 [1.016]
0.39 716P39492L 1.25 [31.75] 0.51 [12.95] 0.90 [22.86] 0.040 [1.016]
0.47 716P47492L 1.25 [31.75] 0.56 [14.22] 0.95 [24.13] 0.040 [1.016]
0.56 716P56492L 1.25 [31.75] 0.61 [15.49] 1.00 [25.40] 0.040 [1.016]
0.68 716P68492M 1.70 [43.18] 0.56 [14.22] 0.94 [23.88] 0.040 [1.016]
0.82 716P82492M 1.70 [43.18] 0.61 [15.49] 1.00 [25.40] 0.040 [1.016]
1.0 716P10592M 1.70 [43.18] 0.68 [17.27] 1.07 [27.18] 0.040 [1.016]
400 VDC/200 VAC**
0.0039 716P39294J 0.70 [17.78] 0.24 [6.10] 0.36 [9.14] 0.032 [0.813]
0.0047 716P47294J 0.70 [17.78] 0.25 [6.35] 0.37 [9.40] 0.032 [0.813]
0.0056 716P56294J 0.70 [17.78] 0.24 [6.10] 0.44 [11.18] 0.032 [0.813]
0.0068 716P68294J 0.70 [17.78] 0.24 [6.10] 0.44 [11.18] 0.032 [0.813]
0.0082 716P82294J 0.70 [17.78] 0.25 [6.35] 0.45 [11.43] 0.032 [0.813]
0.010 716P10394J 0.70 [17.78] 0.27 [6.86] 0.46 [11.68] 0.032 [0.813]
0.012 716P12394J 0.70 [17.78] 0.29 [7.37] 0.48 [12.19] 0.032 [0.813]
0.015 716P15394J 0.70 [17.78] 0.31 [7.87] 0.50 [12.70] 0.032 [0.813]
0.018 716P18394K 0.95 [24.13] 0.28 [7.11] 0.47 [11.94] 0.032 [0.813]
0.022 716P22394K 0.95 [24.13] 0.30 [7.62] 0.49 [12.45] 0.032 [0.813]
0.027 716P27394K 0.95 [24.13] 0.31 [7.87] 0.55 [13.97] 0.032 [0.813]
0.033 716P33394K 0.95 [24.13] 0.33 [8.38] 0.57 [14.48] 0.032 [0.813]
0.039 716P39394K 0.95 [24.13] 0.36 [9.14] 0.60 [15.24] 0.032 [0.813]
0.047 716P47394K 0.95 [24.13] 0.39 [9.91] 0.62 [15.75] 0.032 [0.813]
0.056 716P56394K 0.95 [24.13] 0.40 [10.16] 0.68 [17.27] 0.032 [0.813]
0.068 716P68394K 0.95 [24.13] 0.43 [10.92] 0.72 [18.29] 0.032 [0.813]
0.082 716P82394L 1.25 [31.75] 0.38 [9.65] 0.67 [17.02] 0.040 [1.016]
0.10 716P10494L 1.25 [31.75] 0.42 [10.67] 0.70 [17.78] 0.040 [1.016]
0.12 716P12494L 1.25 [31.75] 0.45 [11.43] 0.73 [18.54] 0.040 [1.016]
0.15 716P15494L 1.25 [31.75] 0.46 [11.68] 0.84 [21.34] 0.040 [1.016]
0.18 716P18494L 1.25 [31.75] 0.50 [12.70] 0.89 [22.61] 0.040 [1.016]
0.22 716P22494L 1.25 [31.75] 0.57 [14.48] 0.95 [24.13] 0.040 [1.016]
0.27 716P27494L 1.25 [31.75] 0.63 [16.00] 1.01 [25.65] 0.040 [1.016]
0.33 716P33494M 1.70 [43.18] 0.57 [14.48] 0.96 [24.38] 0.040 [1.016]
0.39 716P39494M 1.70 [43.18] 0.62 [15.75] 1.01 [25.65] 0.040 [1.016]
0.47 716P47494M 1.70 [43.18] 0.68 [17.27] 1.07 [27.18] 0.040 [1.016]
Type 716P
Polypropylene Film Capacitors
High Performance, ORANGE DROP®Vishay Sprague
Document Number: 42020 For technical questions, contact: spresale@vishay.com www.vishay.com
Revision: 13-Feb-07 29
* These standard ratings are available through Sprague® distribution on special order. For complete Part Number, add letter and number for
terminal and lead length (Ex. 716P103916LD3).
** 60 Hz rms
STANDARD RATINGS* in inches [millimeters]
µF
± 10 % TOLERANCE PART NUMBER SIZE
LT H d
600 VDC/200 VAC**
0.001 716P10296J 0.70 [17.78] 0.27 [6.86] 0.46 [11.68] 0.032 [0.813]
0.0012 716P12296J 0.70 [17.78] 0.24 [6.10] 0.44 [11.18] 0.032 [0.813]
0.0015 716P15296J 0.70 [17.78] 0.26 [6.60] 0.45 [11.43] 0.032 [0.813]
0.0018 716P18296J 0.70 [17.78] 0.27 [6.86] 0.46 [11.68] 0.032 [0.813]
0.0022 716P22296J 0.70 [17.78] 0.28 [7.11] 0.48 [12.19] 0.032 [0.813]
0.0027 716P27296J 0.70 [17.78] 0.25 [6.35] 0.44 [11.18] 0.032 [0.813]
0.0033 716P33296J 0.70 [17.78] 0.25 [6.35] 0.45 [11.43] 0.032 [0.813]
0.0039 716P39296J 0.70 [17.78] 0.26 [6.60] 0.46 [11.68] 0.032 [0.813]
0.0047 716P47296J 0.70 [17.78] 0.28 [7.11] 0.47 [11.94] 0.032 [0.813]
0.0056 716P56296J 0.70 [17.78] 0.30 [7.62] 0.49 [12.45] 0.032 [0.813]
0.0068 716P68296J 0.70 [17.78] 0.32 [8.13] 0.51 [12.95] 0.032 [0.813]
0.0082 716P82296J 0.70 [17.78] 0.32 [8.13] 0.56 [14.22] 0.032 [0.813]
0.01 716P10396J 0.70 [17.78] 0.34 [8.64] 0.58 [14.73] 0.032 [0.813]
0.012 716P12396K 0.95 [24.13] 0.31 [7.87] 0.55 [13.97] 0.032 [0.813]
0.015 716P15396K 0.95 [24.13] 0.34 [8.64] 0.58 [14.73] 0.032 [0.813]
0.018 716P18396K 0.95 [24.13] 0.36 [9.14] 0.60 [15.24] 0.032 [0.813]
0.022 716P22396K 0.95 [24.13] 0.39 [9.91] 0.63 [16.00] 0.032 [0.813]
0.027 716P27396K 0.95 [24.13] 0.41 [10.41] 0.69 [17.53] 0.032 [0.813]
0.033 716P33396K 0.95 [24.13] 0.44 [11.18] 0.73 [18.54] 0.032 [0.813]
0.039 716P39396K 0.95 [24.13] 0.48 [12.19] 0.76 [19.30] 0.032 [0.813]
0.047 716P47396L 1.25 [31.75] 0.42 [10.67] 0.70 [17.78] 0.040 [1.016]
0.056 716P56396L 1.25 [31.75] 0.45 [11.43] 0.73 [18.54] 0.040 [1.016]
0.068 716P68396L 1.25 [31.75] 0.45 [11.43] 0.84 [21.34] 0.040 [1.016]
0.082 716P82396L 1.25 [31.75] 0.49 [12.45] 0.88 [22.35] 0.040 [1.016]
0.1 716P10496L 1.25 [31.75] 0.54 [13.72] 0.93 [23.62] 0.040 [1.016]
0.12 716P12496L 1.25 [31.75] 0.59 [14.99] 0.97 [24.64] 0.040 [1.016]
0.15 716P15496M 1.70 [43.18] 0.55 [13.97] 0.93 [23.62] 0.040 [1.016]
0.18 716P18496M 1.70 [43.18] 0.59 [14.99] 0.98 [24.89] 0.040 [1.016]
0.22 716P22496M 1.70 [43.18] 0.65 [16.51] 1.04 [26.42] 0.040 [1.016]
800 VDC/450 VAC**
0.0056 716P56298L 1.25 [31.75] 0.25 [6.35] 0.45 [11.43] 0.032 [0.813]
0.0068 716P68298L 1.25 [31.75] 0.27 [6.86] 0.46 [11.68] 0.032 [0.813]
0.0082 716P82298L 1.25 [31.75] 0.29 [7.37] 0.48 [12.19] 0.032 [0.813]
0.01 716P10398L 1.25 [31.75] 0.29 [7.37] 0.53 [13.46] 0.032 [0.813]
0.012 716P12398L 1.25 [31.75] 0.31 [7.87] 0.55 [13.97] 0.032 [0.813]
0.015 716P15398L 1.25 [31.75] 0.34 [8.64] 0.58 [14.73] 0.032 [0.813]
0.018 716P18398L 1.25 [31.75] 0.37 [9.40] 0.61 [15.49] 0.032 [0.813]
0.022 716P22398L 1.25 [31.75] 0.38 [9.65] 0.67 [17.02] 0.032 [0.813]
0.027 716P27398L 1.25 [31.75] 0.42 [10.67] 0.70 [17.78] 0.032 [0.813]
0.033 716P33398L 1.25 [31.75] 0.46 [11.68] 0.74 [18.80] 0.032 [0.813]
0.039 716P39398L 1.25 [31.75] 0.46 [11.68] 0.84 [21.34] 0.032 [0.813]
0.047 716P47398L 1.25 [31.75] 0.50 [12.70] 0.88 [22.35] 0.032 [0.813]
0.056 716P56398L 1.25 [31.75] 0.54 [13.72] 0.93 [23.62] 0.032 [0.813]
0.068 716P68398L 1.25 [31.75] 0.59 [14.99] 0.98 [24.89] 0.032 [0.813]
0.082 716P82398M 1.70 [43.18] 0.52 [13.21] 0.90 [22.86] 0.040 [1.016]
0.1 716P10498M 1.70 [43.18] 0.57 [14.48] 0.96 [24.38] 0.040 [1.016]
0.12 716P12498M 1.70 [43.18] 0.62 [15.75] 1.01 [25.65] 0.040 [1.016]
0.14 716P14498M 1.70 [43.18] 0.67 [17.02] 1.06 [26.92] 0.040 [1.016]
www.vishay.com For technical questions, contact: spresale@vishay.com Document Number: 42020
30 Revision: 13-Feb-07
Type 716P
Vishay Sprague Polypropylene Film Capacitors
High Performance, ORANGE DROP®
* These standard ratings are available through Sprague® distribution on special order. For complete Part Number, add letter and number for
terminal and lead length (Ex. 716P103916LD3).
** 60Hz rms
STANDARD RATINGS* in inches [millimeters]
µF
± 10 % TOLERANCE PART NUMBER SIZE
LT Hd
1200 VDC/475 VAC**
0.0027 716P272912L 1.25 [31.75] 0.28 [7.11] 0.48 [12.19] 0.032 [0.813]
0.0033 716P332912L 1.25 [31.75] 0.30 [7.62] 0.49 [12.45] 0.032 [0.813]
0.0039 716P392912L 1.25 [31.75] 0.30 [7.62] 0.54 [13.72] 0.032 [0.813]
0.0047 716P472912L 1.25 [31.75] 0.32 [8.13] 0.56 [14.22] 0.032 [0.813]
0.0056 716P562912L 1.25 [31.75] 0.34 [8.64] 0.58 [14.73] 0.032 [0.813]
0.0068 716P682912L 1.25 [31.75] 0.37 [9.40] 0.61 [15.49] 0.032 [0.813]
0.0082 716P822912L 1.25 [31.75] 0.38 [9.65] 0.67 [17.02] 0.032 [0.813]
0.01 716P103912L 1.25 [31.75] 0.42 [10.67] 0.70 [17.78] 0.032 [0.813]
0.012 716P123912L 1.25 [31.75] 0.45 [11.43] 0.73 [18.54] 0.032 [0.813]
0.015 716P153912L 1.25 [31.75] 0.46 [11.68] 0.84 [21.34] 0.032 [0.813]
0.018 716P183912L 1.25 [31.75] 0.50 [12.70] 0.88 [22.35] 0.032 [0.813]
0.022 716P223912L 1.25 [31.75] 0.54 [13.72] 0.93 [23.62] 0.032 [0.813]
0.027 716P273912L 1.25 [31.75] 0.60 [15.24] 0.99 [25.15] 0.032 [0.813]
0.033 716P333912M 1.70 [43.18] 0.53 [13.46] 0.91 [23.11] 0.040 [1.016]
0.039 716P393912M 1.70 [43.18] 0.57 [14.48] 0.96 [24.38] 0.040 [1.016]
0.047 716P473912M 1.70 [43.18] 0.62 [15.75] 1.01 [25.65] 0.040 [1.016]
0.056 716P563912M 1.70 [43.18] 0.68 [17.27] 1.07 [27.18] 0.040 [1.016]
1600 VDC/500 VAC**
0.001 716P102916L 1.25 [31.75] 0.28 [7.11] 0.47 [11.94] 0.032 [0.813]
0.0012 716P122916L 1.25 [31.75] 0.29 [7.37] 0.48 [12.19] 0.032 [0.813]
0.0015 716P152916L 1.25 [31.75] 0.30 [7.62] 0.50 [12.70] 0.032 [0.813]
0.0018 716P182916L 1.25 [31.75] 0.31 [7.87] 0.55 [13.97] 0.032 [0.813]
0.0022 716P222916L 1.25 [31.75] 0.32 [8.13] 0.56 [14.22] 0.032 [0.813]
0.0027 716P272916L 1.25 [31.75] 0.35 [8.89] 0.59 [14.99] 0.032 [0.813]
0.0033 716P332916L 1.25 [31.75] 0.37 [9.40] 0.61 [15.49] 0.032 [0.813]
0.0039 716P392916L 1.25 [31.75] 0.38 [9.65] 0.67 [17.02] 0.032 [0.813]
0.0047 716P472916L 1.25 [31.75] 0.41 [10.41] 0.69 [17.53] 0.032 [0.813]
0.0056 716P562916L 1.25 [31.75] 0.43 [10.92] 0.72 [18.29] 0.032 [0.813]
0.0068 716P682916L 1.25 [31.75] 0.47 [11.94] 0.75 [19.05] 0.032 [0.813]
0.0082 716P822916L 1.25 [31.75] 0.47 [11.94] 0.85 [21.59] 0.032 [0.813]
0.01 716P103916L 1.25 [31.75] 0.51 [12.95] 0.90 [22.86] 0.032 [0.813]
0.012 716P123916L 1.25 [31.75] 0.55 [13.97] 0.94 [23.88] 0.032 [0.813]
0.015 716P153916M 1.70 [43.18] 0.49 [12.45] 0.87 [22.10] 0.040 [1.016]
0.018 716P183916M 1.70 [43.18] 0.53 [13.46] 0.91 [23.11] 0.040 [1.016]
0.022 716P223916M 1.70 [43.18] 0.58 [14.73] 0.96 [24.38] 0.040 [1.016]
0.027 716P273916M 1.70 [43.18] 0.63 [16.0] 1.02 [25.91] 0.040 [1.016]
0.033 716P333916M 1.70 [43.18] 0.69 [17.53] 1.08 [27.43] 0.040 [1.016]
ORDERING INFORMATION
716P 104 9 1 J D 3
TYPE CAPACITANCE TOLERANCE DC VOLTAGE
RATING
CASE
CODE
TER M I NAL L E A D L EN G TH
Capacitance is expressed in
picofarads. The first two
digits are significant. The
third is the number of zeros
to follow. Values must
conform to decade rating for
the tolerance specified.
0 = ± 20 %
9 = ± 10 %
5 = ± 5 %
This is expressed
in hundred of
volts.
See Dimensions A = Straight lead
B = Hairpin crimped
D = Hockey crimped
1 = 0.187" ± 0.030"
[4.750 ± 0.762]
2 = 0.250" ± 0.030"
[6.350 ± 0.762]
3 = 1.250" [31.750]
Minimum
Legal Disclaimer Notice
www.vishay.com Vishay
Revision: 12-Mar-12 1Document Number: 91000
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree
to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and
damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay
or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to
obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
