LM8322
LM8322 Mobile I/O Companion Supporting Key-Scan, I/O Expansion, PWM, and
ACCESS.bus Host Interface
Literature Number: SNLS268F
LM8322
OBSOLETE
October 4, 2011
Mobile I/O Companion Supporting Key-Scan, I/O
Expansion, PWM, and ACCESS.bus Host Interface
1.0 General Description
The LM8322 Mobile I/O Companion is a dedicated device to
unburden a host processor from scanning a matrix-addressed
keypad. In addition, the LM8322 provides general-purpose
I/O expansion, and PWM outputs useful for dynamic LED
brightness modulation.
It communicates with the host through an I2C-compatible
ACCESS.bus interface. An interrupt output is available for
signaling key-press and key-release events. Communication
frequencies up to 400 kHz (Fast-mode) bus speed are sup-
ported. The LM8322 supports a predefined set of commands.
These commands enable a host device to keep control over
all functions.
2.0 Features
Key Features
■Supports keypad matrices of up to 8 × 12 keys plus 8
special-function (SF) keys for a total of 104 keys. SF keys
pull keypad scan inputs directly to ground, rather than
connecting to a keypad scan output.
■Supports I2C-compatible ACCESS.bus interface in slave
mode up to 400 kHz (Fast-mode).
■Three host-programmable PWM outputs useful for smooth
LED brightness modulation.
■Supports general-purpose I/O expansion on pins not
otherwise used for keypad interface.
■Key-scan event storage in a FIFO buffer for up to 15
events.
■Key events, errors, and dedicated hardware interrupts
request host service by asserting the IRQ output.
■The correct reception of a command may be assumed, if
no error is reported from the LM8322 after receiving a
command.
■Wake-up from Halt mode on any matrix key-scan event,
any use of the SF keys, or any activity on the ACCESS.bus
interface.
3.0 Applications
■Mobile phones
■Personal Digital Assistants (PDAs)
■Smart handheld devices
■Personal media players
4.0 Block Diagram
30013620
© 2011 National Semiconductor Corporation 300136 www.national.com
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322 Mobile I/O Companion Supporting Key-Scan, I/O Expansion, PWM, and ACCESS.bus
Host Interface
5.0 Ordering Information
NSID Spec. No. of Pins Package Type Temperature Package Method
LM8322JGR8 NOPB 36 Micro-Array −40 to + 85°C 1000 pcs Tape & Reel
LM8322JGR8X NOPB 36 Micro-Array −40 to + 85°C 3500 pcs Tape & Reel
NOPB = No PB (No Lead)
6.0 Pin Assignments
30013621
Top View
36–Pin MICRO-ARRAY Package
See NS Package Number GRA36A
www.national.com 2
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
Table of Contents
1.0 General Description ......................................................................................................................... 1
2.0 Features ........................................................................................................................................ 1
3.0 Applications .................................................................................................................................... 1
4.0 Block Diagram ................................................................................................................................ 1
5.0 Ordering Information ........................................................................................................................ 2
6.0 Pin Assignments ............................................................................................................................. 2
7.0 Signal Descriptions .......................................................................................................................... 5
7.1 TERMINATION OF UNUSED SIGNALS ...................................................................................... 6
8.0 Application Example ........................................................................................................................ 7
8.1 FEATURES ............................................................................................................................. 7
9.0 Clocks ........................................................................................................................................... 8
9.1 INTERNAL EXECUTION CYCLE ............................................................................................... 8
9.2 BUFFERED CLOCK ................................................................................................................. 8
9.3 CLOCK CONFIGURATION ....................................................................................................... 9
10.0 Reset ......................................................................................................................................... 10
10.1 EXTERNAL RESET .............................................................................................................. 10
10.2 POWER-ON RESET (POR) ................................................................................................... 10
10.3 PIN CONFIGURATION AFTER RESET ................................................................................... 10
10.4 DEVICE CONFIGURATION AFTER RESET ............................................................................ 11
10.5 CONFIGURATION INPUTS ................................................................................................... 11
10.6 INITIALIZATION ................................................................................................................... 11
10.7 INITIALIZATION EXAMPLE ................................................................................................... 13
11.0 Halt Mode ................................................................................................................................... 13
11.1 ACCESS.bus ACTIVITY ........................................................................................................ 13
12.0 Keypad Interface ......................................................................................................................... 14
12.1 EVENT CODE ASSIGNMENT ................................................................................................ 14
12.2 KEYPAD SCAN CYCLES ...................................................................................................... 14
12.2.1 Timing Parameters ..................................................................................................... 15
12.2.2 Multiple Key Pressings ................................................................................................ 15
12.3 EXAMPLE KEYPAD CONFIGURATION .................................................................................. 15
13.0 General-Purpose I/O Ports ............................................................................................................ 16
13.1 USING THE CONFIG_X PINS FOR GPIO ............................................................................... 17
13.2 GPIO TIMING ...................................................................................................................... 17
14.0 PWM Output Generation ............................................................................................................... 18
14.1 COMMAND QUEUE ............................................................................................................. 18
14.2 PWM TIMER OPERATION .................................................................................................... 18
14.3 PWM SCRIPT COMMANDS .................................................................................................. 19
14.4 RAMP COMMAND ............................................................................................................... 20
14.5 SET_PWM COMMAND ......................................................................................................... 20
14.6 GO_TO_START COMMAND ................................................................................................. 20
14.7 BRANCH COMMAND ........................................................................................................... 20
14.8 END COMMAND .................................................................................................................. 21
14.9 TRIGGER COMMAND .......................................................................................................... 21
14.10 PWM SCRIPT EXAMPLE .................................................................................................... 21
14.10.1 PWM Channel 0 Script .............................................................................................. 22
14.10.2 PWM Channel 1 Script .............................................................................................. 22
14.10.3 PWM Channel 2 Script .............................................................................................. 22
14.11 SELECTABLE SCRIPT EXAMPLE ........................................................................................ 23
15.0 Digital Multiplexers ....................................................................................................................... 24
16.0 Host Interface ............................................................................................................................. 25
16.1 START AND STOP CONDITIONS .......................................................................................... 25
16.2 CONTINUOUS COMMAND STRINGS .................................................................................... 25
16.3 DEVICE ADDRESS .............................................................................................................. 25
16.4 HOST WRITE COMMANDS .................................................................................................. 25
16.5 HOST READ COMMANDS .................................................................................................... 26
16.6 INTERRUPTS ...................................................................................................................... 26
16.7 INTERRUPT CODE .............................................................................................................. 27
16.8 ERROR CODE ..................................................................................................................... 27
16.9 WAKE-UP FROM HALT MODE .............................................................................................. 27
17.0 Host Commands .......................................................................................................................... 29
17.1 READ_ID COMMAND ........................................................................................................... 30
17.2 WRITE_CFG COMMAND ...................................................................................................... 30
17.3 READ_INT COMMAND ......................................................................................................... 31
17.4 RESET COMMAND .............................................................................................................. 31
3 www.national.com
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
17.5 WRITE_PULL_DOWN COMMAND ......................................................................................... 32
17.6 WRITE_PORT_SEL COMMAND ............................................................................................ 32
17.7 WRITE_PORT_STATE COMMAND ........................................................................................ 33
17.8 READ_PORT_SEL COMMAND ............................................................................................. 33
17.9 READ_PORT_STATE COMMAND ......................................................................................... 34
17.10 READ_FIFO COMMAND ..................................................................................................... 34
17.11 RPT_READ_FIFO COMMAND ............................................................................................. 34
17.12 SET_ACTIVE COMMAND ................................................................................................... 35
17.13 READ_ERROR COMMAND ................................................................................................. 35
17.14 SET_DEBOUNCE COMMAND ............................................................................................. 36
17.15 SET_KEY_SIZE COMMAND ................................................................................................ 36
17.16 READ_KEY_SIZE COMMAND ............................................................................................. 36
17.17 READ_CFG COMMAND ..................................................................................................... 37
17.18 WRITE_CLOCK COMMAND ................................................................................................ 37
17.19 READ_CLOCK COMMAND ................................................................................................. 37
17.20 PWM_WRITE COMMAND ................................................................................................... 38
17.21 PWM_START COMMAND ................................................................................................... 38
17.22 PWM_STOP COMMAND ..................................................................................................... 38
18.0 Absolute Maximum Ratings ........................................................................................................... 39
19.0 DC Electrical Characteristics ......................................................................................................... 39
20.0 AC Electrical Characteristics ......................................................................................................... 40
21.0 Physical Dimensions .................................................................................................................... 42
www.national.com 4
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
7.0 Signal Descriptions
Pin Function I/O Description
A6 KP-X0 Input Wake-up input/Keyboard scanning input 0
A5 KP-X1 Input Wake-up input/Keyboard scanning input 1
F1 KP-X2 Input Wake-up input/Keyboard scanning input 2
F2 KP-X3 Input Wake-up input/Keyboard scanning input 3
GPIO_13 I/O General-purpose I/O port 13
A2 KP-X4 Input Wake-up input/Keyboard scanning input 4
GPIO_12 I/O General-purpose I/O port 12
B3 KP-X5 Input Wake-up input/Keyboard scanning input 5
GPIO_11 I/O General-purpose I/O port 11
A3 KP-X6 Input Wake-up input/Keyboard scanning input 6
GPIO_10 I/O General-purpose I/O port 10
B4 KP-X7 Input Wake-up input/Keyboard scanning input 7
GPIO_09 Input General-purpose I/O port 9
C6 KP_Y0 Output Keyboard scanning output 0
C5 KP-Y1 Output Keyboard scanning output 1
B6 KP-Y2 Output Keyboard scanning output 2
B5 KP-Y3 Output Keyboard scanning output 3
GPIO_08 I/O General-purpose I/O port 8
B2 KP-Y4 Output Keyboard scanning output 4
GPIO_07 I/O General-purpose I/O port 7
A1 KP-Y5 Output Keyboard scanning output 5
GPIO_06 I/O General-purpose I/O port 6
B1 KP-Y6 Output Keyboard scanning output 6
GPIO_05 I/O General-purpose I/O port 5
C2 KP-Y7 Output Keyboard scanning output 7
GPIO_04 I/O General-purpose I/O port 4
E3
KP-Y8 Output Keyboard scanning output 8
SLOWCLKOUT Output 32.768 kHz clock output
GPIO_03 I/O General-purpose I/O port 3
D5
KP-Y9 Output Keyboard scanning output 9
MUX2_IN1 Input Multiplexer 2 input 1
GPIO_02 I/O General-purpose I/O port 2
E6
KP-Y10 Output Keyboard scanning output 10
MUX2_IN2 Input Multiplexer 2 input 2
GPIO_01 I/O General-purpose I/O port 1
F6
KP-Y11 Output Keyboard scanning output 11
MUX2_OUT Output Multiplexer 2 output
GPIO_00 I/O General-purpose I/O port 0
E2 ACB_SDA I/O ACCESS.bus data signal
E1 ACB_SCL I/O ACCESS.bus clock signal
E4 PWM_0 Output Pulse-width modulated output 0
MUX_IN1 Input Multiplexer 1 input 1
F5 PWM_1 Output Pulse-width modulated output 1
MUX_IN2 Input Multiplexer 1 input 2
E5
PWM_2 Output Pulse-width modulated output 2
MUX1_OUT Output Multiplexer 1 output
CONFIG_2 Input Slave address select input 2
GPIO_15 I/O General-purpose I/O port 15
5 www.national.com
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
Pin Function I/O Description
D6 CONFIG_1 Input Slave address select input 1
GPIO_14 I/O General-purpose I/O port 14
D1 XTAL_OUT Input 32.768 kHz crystal output
D2 SLOWCLK Input 32.768 kHz clock
XTAL_IN Input 32.768 kHz crystal input
F3 IRQ Output Interrupt request output
C1 RESET Input Reset Input
A4, F4 VCC n.a. VCC
C3, C4,
D3, D4 GND n.a. Ground
7.1 TERMINATION OF UNUSED SIGNALS
TABLE 1. Termination of Unused Signals
Signal Termination
RESET Connect to VCC if not driven from an external Supervisory circuit.
CONFIG_1 Connect to VCC or GND through a pullup or pulldown resistor because the slave address is selected
by the level on this pin. This pin cannot be left unconnected.
XTAL_IN This pin is a high-impedance input and must be connected to VCC or GND if it is unused.
XTAL_OUT This pin has a weak pullup and can be left open-circuit if it is unused.
KP-X[2:0] These pins are dedicated keypad pins. In the minimum configuration, these pins are keypad inputs
with weak pullups.
KP-X[7:3]
These pins are in high-impedance mode after power-on initialization. There are two ways to handle
these pins if unused:
• Connect to VCC or GND.
• Program as inputs with weak pullups or outputs.
Care must be taken when connecting to VCC or GND. Erroneous parameters sent with the
WRITE_PORT_SEL or WRITE_PORT_STATE commands could cause excessive current
consumption. A better approach is to leave unused keyboard inputs open-circuit and use the
WRITE_PORT_SEL and WRITE_PORT_STATE commands to configure the pins as inputs with
weak pullups or outputs.
KP-X7 can only be an input. This pin should be programmed as an input with a weak pullup.
KP-Y[2:0] These pins are dedicated keypad pins. In the minimum configuration, these pins are keypad outputs
driven low.
KP-Y[11:3]
These pins are in high-impedance mode after power-on initialization. There are two ways to handle
these pins if unused:
• Connect to VCC or GND.
• Program as inputs with weak pullups or outputs
Care must be taken when connecting to VCC or GND. Erroneous parameters sent with the
WRITE_PORT_SEL or WRITE_PORT_STATE commands could cause excessive current
consumption. A better approach is to leave unused keyboard inputs open-circuit and use the
WRITE_PORT_SEL and WRITE_PORT_STATE commands to configure the pins as inputs with
weak pullups or outputs.
PWM_0,
PWM_1
These pins must be connected to VCC or GND if they are not used for any optional function
described in the datasheet.
PWM_2/
CONFIG_2
Connect to VCC or GND through a pullup or pulldown resistor because the slave address is selected
by the level on this pin. This pin cannot be left unconnected.
IRQ This pin must be connected.
www.national.com 6
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
8.0 Application Example
30013601
FIGURE 1. Typical Application
8.1 FEATURES
The application example shown in Figure 1 supports the fol-
lowing features:
•8 x 9 standard keys.
•8 special function keys (SF keys) with wake-up capability
by forcing a WAKE_INx pin to ground. Pressing a SF key
overrides any other key in the same row.
•ACCESS.bus (I2C-compatible) interface for
communication with the host.
•Hardware IRQ interrupt to host to signal keypad, error, and
status events. By default, this is an open-drain output, so
an external pullup resistor may be required to avoid false
assertion. The host can program this output for push-pull
mode, in which case the pullup might not be required, if
the host can ignore a false assertion before the LM8322
has been programmed.
•Two LEDs driven by PWM outputs with programmable
ramp-up and ramp-down. PWM_2 (shared with GPIO_15
and CONFIG_2) could be used as an additional PWM
driver port to control a third external LED.
•ACCESS.bus address is selected by the CONFIG_1 and
CONFIG_2 inputs. These pins may also be used as GPIO
pins after reset initialization has occurred. If extra GPIO
pins are not needed, CONFIG_1 and CONFIG_2 may be
tied directly to VCC and GND.
•Crystal pins XTAL_IN and XTAL_OUT may be used to
connect to an external 32.768 kHz crystal or receive an
external 32.768 kHz clock input for running the PWM
peripheral. By default, the PWM is clocked by an on-chip
clock source.
7 www.national.com
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
9.0 Clocks
•System Clock (mclk) — The system clock is in the range
of about 21 MHz (± 7%) typical. This clock is used to drive
the I2C compatible serial ACCESS bus and is the input
clock for other function blocks.
•Processing and Command Execution Clock (tC) — The
internal processing is based on a 2 MHz clock. This clock
is derived from the System Clock.
•Internal PWM Clock — The internal PWM clock is a fixed
scaled down clock (÷ 64) of the Processing and Command
Execution Clock. This clock is close to 32 kHz which is in
a good range to source the PWM function block as an
alternative to an external clock source.
•External 32.768 kHz Clock — driven into the SLOWCLK
input. May be used internally as the timebase for the PWM
and driven on the SLOWCLKOUT output.
•External 32.768 kHz Crystal — connected across the
XTAL_IN and XTAL_OUT pins (XTAL_IN is an alternate
function of the SLOWCLK pin). May be used internally as
the timebase for the PWM and driven on the
SLOWCLKOUT output.
30013602
FIGURE 2. Clock Architecture
9.1 INTERNAL EXECUTION CYCLE
The Processing - and Command - execution clock is about 2
MHz. This clock is stopped in Halt mode, which only occurs
under control of the LM8322. However, the host can set the
period of inactivity which causes the device to enter Halt
mode.
Exit from Halt mode can be triggered by any of these events:
•Occurrence of a key-press or key-release event.
•A Start condition driven by the host on the ACCESS.bus
interface.
•Assertion of the RESET input.
After reset, the default timebase for the PWM outputs is the
internal execution clock divided by 64.
9.2 BUFFERED CLOCK
The timebase for the PWM comes from any of three sources:
•Prescaled internal Execution clock.
•External 32.768 kHz clock received on the SLOWCLK
input.
•On-chip oscillator with an external crystal connected
across XTAL_IN and XTAL_OUT.
Any of these sources may be buffered and driven on the
SLOWCLKOUT output. The clock buffer is enabled with the
WRITE_CLOCK command.
If XTAL_IN is not used it must be terminated to VCC or GND.
www.national.com 8
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
9.3 CLOCK CONFIGURATION
Table 2 shows the clock configurations available by loading
the clock configuration register with the WRITE_CLOCK com-
mand. The WRITE_CLOCK command must be issued only
once during system initialization. This command is used to
override the default settings.
TABLE 2. Clock Configuration Register
7 6 5 4 3 2 1 0
0 SLOWCLKOUT 0 0 SLOWCLKEN 0 RCPWM
Bit Value Description
SLOWCLKOUT 0 Disable SLOWCLKOUT buffer.
1 Enable SLOWCLKOUT buffer.
SLOWCLKEN
0 External 32.768 kHz crystal is installed between the XTAL_IN and XTAL_OUT pins.
1External 32.768 kHz clock is received on the SLOWCLK pin, or no 32.768 kHz clock
is required.
RCPWM
00 On-chip RC clock divided by 64 drives the PWM and clock buffer.
01 Reserved.
10 Reserved.
11 External 32.768 kHz clock or crystal drives the PWM and clock buffer.
The SLOWCLKOUT signal is an alternate function of the pin
used for the KP-Y8 scanning output and the GPIO_03 port. If
the SLOWCLKOUT function is enabled, these other functions
of the pin are unavailable.
9 www.national.com
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
10.0 Reset
The LM8322 may be reset by either an external reset, RE-
SET command, or an internally generated power-on reset
(POR) signal. The RESET input must not be allowed to float.
If the external RESET input is not used, it must be connected
to VCC, either directly or through a pull-up resistor.
10.1 EXTERNAL RESET
The device enters a reset state immediately when the RE-
SET input is driven low. RESET must be held low for a
minimum of 700 ns to guarantee a valid reset. If RESET is
asserted at power-on, it must be held low until VCC rises above
the minimum operating voltage (1.62V). If an RC circuit is
used to drive RESET, it must have a time constant 5 times
(5×) greater than the VCC rise time to this level.
When RESET goes low, the I/O ports are initialized immedi-
ately, any observed delay being only propagation delay.
When the RESET pin goes high, the LM8322 comes out of
the reset state within about 1400 ns.
10.2 POWER-ON RESET (POR)
The POR circuit is always enabled. When VCC rises above the
POR threshold voltage VPOR (about 1.2–1.5V), an on-chip
reset signal is asserted. The VCC rise time must be greater
than 20 µs and less than 10 ms, otherwise the on-chip reset
signal may deassert before VCC reaches the minimum oper-
ating voltage. While VCC is below VPOR, the LM8322 is held
in reset and a timer clocked by the on-chip RC clock is preset
with 0xFF (256 clock cycles). When VCC reaches a value
greater than VPOR, the timer starts counting down. When it
underflows, the on-chip reset signal is deasserted and the
LM8322 begins operation.
10.3 PIN CONFIGURATION AFTER RESET
Table 2 shows the pin configuration after reset.
TABLE 3. Pin Configuration After Reset
Pins After Reset After LM8322 Initialization
KP-X00
High-impedance mode. Input mode with an on-chip pullup enabled.KP-X01
KP-X02
KP-X03
High-impedance mode. High-impedance mode, until host configures them as keypad inputs
or GPIO.
KP-X04
KP-X05
KP-X06
KP-X07
KP-Y00
High-impedance mode. Active drive low.KP-Y01
KP-Y02
KP-Y03
High-impedance mode. High-impedance mode, until host configures them as keypad outputs
or GPIO.
KP-Y04
KP-Y05
KP-Y06
KP-Y07
KP-Y08
KP-Y09
KP-Y10
KP-Y11
CONFIG_1 High-impedance mode. The ACCESS.bus slave address must be selected with external
pullup or pulldown resistors or direct connections to VCC or GND.
CONFIG_2
IRQ High-impedance mode. Active drive low.
PWM_0
High-impedance mode. High-impedance mode.PWM_1
PWM_2
ACB_SDA Open-drain mode. Open-drain mode.
ACB_SCL
XTAL_IN High-impedance mode. High-impedance mode. Terminate to VCC or GND if not used.
XTAL_OUT Weak pullup device. Weak pullup device.
RESET High-impedance mode. High-impedance mode.
www.national.com 10
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
10.4 DEVICE CONFIGURATION AFTER RESET
After the LM8322 has completed its reset initialization, it will
have the following internal configuration:
•PWM Clock — the PWM clock source is the on-chip clock
divided by 64. This remains in effect until changed by a
host command.
•Keypad Size — 3 × 3.
•Digital Multiplexers — disabled.
•IRQ — enabled, active low.
•NOINIT Bit — set.
•Debounce Time — 3 scan cycles (about 12 milliseconds).
•Active Time — 500 milliseconds.
10.5 CONFIGURATION INPUTS
The states sampled from the CONFIG_1 and CONFIG_2 in-
puts during reset select the ACCESS.bus address used by
the LM8322, as shown in Table 4. The address occupies the
high seven bits of the first byte of a bus transaction, with the
LSB (shown as X below) indicating the direction of transfer.
TABLE 4. Bus Address Selection
CONFIG_1 CONFIG_2 Bus Address
0 0 1000 010X
0 1 1000 011X
1 0 1000 100X
1 1 1000 101X
When these pins are used as GPIO ports, the design must
ensure that they have the desired states during reset. For ex-
ample, a 100-kohm resistor to ground can impose a logic 0
during reset without interfering with normal operation as a
GPIO port.
10.6 INITIALIZATION
The LM8322 waits for a WRITE_CFG command from the
host. During this time, IRQ is asserted to request service from
the host. Figure 3 describes the behavior of the LM8322 fol-
lowing reset.
30013603
FIGURE 3. LM8322 Initialization Behavior
Figure 4 shows the timing of IRQ relative to a RESET or POR
event and the WRITE_CFG command. 100 µs after a RE-
SET or POR event, IRQ is asserted and any READ_INT
command will return an interrupt code with the NOINIT bit set.
90 µs after a WRITE_CFG command is received, IRQ is de-
asserted.
30013604
FIGURE 4. IRQ Reset Timing
11 www.national.com
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
After sending the WRITE_CFG command, the host must send
a series of commands to configure the LM8322, as shown in
Figure 5 (see left hand side).
This Flow - diagram illustrates also the basic host communi-
cation steps which the host must execute upon an IRQ re-
quest received from the LM8322 during operation. Such
requests will be made from the LM8322 as a result of key
pressed events, the detection of an error, the termination of
a PWM cycle and others.
30013605
FIGURE 5. Host-Side LM8322 Initialization
www.national.com 12
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
10.7 INITIALIZATION EXAMPLE
In the following example, the LM8322 is configured as:
•Keypad matrix configuration is 8 × 4.
•GPIO_03 through GPIO_07 are available to use as GPIO
pins.
•GPIO_03 is an output driven low.
•GPIO_4 and GPIO_5 are outputs driven high.
•GPIO_06 and GPIO_07 are inputs with weak pulldowns.
•GPIO_14 and GPIO_15 are inputs with weak pullups.
•The PWM clock source is the internal execution clock
divided by 64 (about 32 kHz).
Most of these settings can be verified by executing com-
mands such as READ_CONF, READ_PORT_SEL,
READ_CLOCK, etc.
ALL GPIO pin states can be read using the
READ_PORT_STATE command, without regard to whether
the pin is an input or an output.
An open-drain signal can be created by alternating between
input mode and driving the output low.
All GPIO s can sink and source 16 mA when configured as
an output.
Command Encoding Parameter 1 Parameter 2 Description
WRITE_CFG 0x81 0x40 Selects 36-pin package and disables the two digital
multiplexers.
WRITE_CLK 0x93 0x08 SLOWCLKOUT disabled, no external 32.768 kHz clock
required, PWM clock source is internal.
SET_KEY_SIZE 0x90 0x84 Selects a keypad matrix size of 8 × 4.
SET_ACTIVE 0x8B 0x4B Sets the active time to about 300 milliseconds (75 × 4
milliseconds).
SET_DEBOUNCE 0x8F 0x03
Sets the key debouncing time to about 12 milliseconds
(3 × 4 ms). This is actually the default and would not have
to be performed.
WRITE_PORT_SEL 0x85 0x00 0x38
Configure GPIO_03, GPIO_04, and GPIO_05 as
outputs. Configure GPIO_06, GPIO_07, GPIO_14, and
GPIO_15 as inputs.
WRITE_PULL_DOWN 0x84 0x00 0x3F
Set the direction for the pullup/pulldown devices on
GPIO_06 and GPIO_07 to pulldown. Set the direction for
the pullup/pulldown devices on GPIO_14 and GPIO_15
to pullup.
WRITE_PORT_STATE 0x86 0xC0 0xF0
Set GPIO_04 and GPIO_05 to drive high. Enable the
pullups on GPIO_06, GPIO_07, GPIO_14, and
GPIO_15.
11.0 Halt Mode
The fully static architecture of the LM8322 allows stopping the
internal RC clock in Halt mode, which reduces power con-
sumption to the minimum level. Figure 6 shows the current in
Halt mode at the maximum VCC (1.98V) from 25°C to +85°C.
30013606
FIGURE 6. Halt Current vs. Temperature at 1.98V
Halt mode is entered when no key-press event, key-release
event, or ACCESS.bus activity is detected for a certain period
of time (by default, 500 milliseconds). The mechanism for en-
tering Halt mode is always enabled in hardware, but the host
can program the period of inactivity which triggers entry into
Halt mode.
11.1 ACCESS.bus ACTIVITY
When the LM8322 is in Halt mode, any activity on the
ACCESS.bus interface will cause the LM8322 to exit from
Halt mode. However, the LM8322 will not be able to acknowl-
edge the first bus cycle immediately following wake-up from
Halt mode. It will respond with a negative acknowledgement,
and the host should then repeat the cycle.
The LM8322 will be prevented from entering Halt mode if it
shares the bus with peripherals that are continuously active.
For lowest power consumption, the LM8322 should only
share the bus with peripherals that require little or no bus ac-
tivity after system initialization.
13 www.national.com
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
12.0 Keypad Interface
12.1 EVENT CODE ASSIGNMENT
After power-on reset and host initialization, the LM8322 starts
scanning the keypad. It stays active for a default time of about
500 ms after the last key is released, after which it enters Halt
mode to minimize power consumption (typically <5 µA stand-
by current).
Table 5 lists the codes assigned to the matrix positions en-
coded by the hardware. Key-press events are assigned the
codes listed in Table 5 , but with the MSB set. When a key is
released, the MSB of the code is clear.
TABLE 5. Keypad Matrix Code Assignments
KP-Y0 KP-Y1 KP-Y2 KP-Y3 KP-Y4 KP-Y5 KP-Y6 KP-Y7 KP-Y8 KP-Y9 KP-Y10 KP-Y11 SF Keys
KP-X0 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 0x0A 0x0B 0x0C 0x0F
KP-X1 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1F
KP-X2 0x21 0x22 0x23 0x24 0x25 0x26 0x27 0x28 0x29 0x2A 0x2B 0x2C 0x2F
KP-X3 0x31 0x32 0x33 0x34 0x35 0x36 0x37 0x38 0x39 0x3A 0x3B 0x3C 0x3F
KP-X4 0x41 0x42 0x43 0x44 0x45 0x46 0x47 0x48 0x49 0x4A 0x4B 0x4C 0x4F
KP-X5 0x51 0x52 0x53 0x54 0x55 0x56 0x57 0x58 0x59 0x5A 0x5B 0x5C 0x5F
KP-X6 0x61 0x62 0x63 0x64 0x65 0x66 0x67 0x68 0x69 0x6A 0x6B 0x6C 0x6F
KP-X7 0x71 0x72 0x73 0x74 0x75 0x76 0x77 0x78 0x79 0x7A 0x7B 0x7C 0x7F
The codes are loaded into the FIFO buffer in the order in
which they occurred. Table 6 shows an example sequence of
events, and Figure 7 shows the resulting sequence of event
codes loaded into the FIFO buffer.
TABLE 6. Example Sequence of Events
Event Number Event Code Event on Input Driven Output Description
1 0xC5 KP-X4 KP-Y4 Key is pressed
2 0xB2 KP-X3 KP-Y1 Key is pressed
3 0x45 KP-X4 KP-Y4 Key is released
4 0x32 KP-X3 KP-Y1 Key is released
5 0x81 KP-X0 KP-Y0 Key is pressed
6 0x5F KP-X5 n.a. SF Key is released
7 0x01 KP-X0 KP-Y0 Key is released
8 0x00 n.a. n.a. Indicates end of stored events
30013607
FIGURE 7. Example Event Codes Loaded in FIFO Buffer
12.2 KEYPAD SCAN CYCLES
The LM8322 starts new scan cycles at fixed time intervals of
about 4 milliseconds. If a change in the state of the keypad is
detected, the keypad is rescanned after a debounce delay.
When the state change has been reliably captured, it is en-
coded and written to the FIFO buffer.
Figure 8 shows the relationship between a KP-Yx output and
a KP-Xx input over multiple scan cycles during a key press
event. Between scan cycles, the KP-Yx outputs that are spec-
ified by the SET_KEY_SIZE command (0x90) for keypad
scanning are driven low.
30013608
FIGURE 8. Keypad Scan Cycles
www.national.com 14
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
During a scan cycle, only one KP-Yx output pin will be driven
low at any time, while the others are driven high or undriven.
At the time scale used in Figure 8, the low phase of a KP-Yx
output during a scan cycle is not visible. The KP-Xx input pins
are pulled high by weak pullups.
There are capacitive loads on the KP-Xx inputs and KP-Yx
outputs due to protection circuits, wiring, etc. The LM8322 in-
serts delays to allow complete charging or discharging of
these loads before sampling the input levels on the KP-Xx
inputs. The maximum parasitic load capacitance on the KP-
Xx inputs is 5 nF.
After detecting a key-press or key-release event, the de-
bounce time specified by the SET_DEBOUNCE command
(0x8F) sets the minimum time for confirming the event before
the IRQ output is asserted.
If more than two keys are pressed simultaneously, the pattern
of key closures may be ambiguous, in which case the the in-
terrupt code indicates an error and the IRQ output is asserted
(if enabled).
The SF keys connect KP-Xx inputs directly to ground. There
can be up to eight SF-keys. If any of these keys are pressed,
other keys that use the same KP-Xx pin are ignored.
12.2.1 Timing Parameters
Two timing parameters affect scanning of the keypad:
•Debounce Time — minimum delay between detecting a
keypad event and confirming the event before asserting
IRQ. The default debounce time is 3 scan cycles (about
12 milliseconds), but the host can set values in the range
1–255 cycles (4–1020 milliseconds).
•Active Time — period without detecting a state change in
the keypad that triggers entry into Halt mode, during which
keypad scanning is suspended. The default active time is
500 milliseconds, but the host can set it values in the range
4–1020 milliseconds. The active time must be greater than
the debounce time.
12.2.2 Multiple Key Pressings
If more than two keys are pressed at the same time, the
LM8322 stores all key pressed and released events in the
FIFO buffer in the sequence in which they were decoded.
For multiple key pressings the following circumstances have
to be respected:
•A multiple key-press event is given if two or more key-
press events are reported but no corresponding key-
release event.
•With the activity time set between the minimum and
maximum time (4 msec to 1 second) it is not safe to detect
two simultaneous key pressings in one input row (see
Figure 9 on the left hand side.)
•If all key pressings (two or more) are located in different
input rows (see Figure 9 on the right hand side) then the
key pressed events will be correctly found in the FIFO
buffer without any restriction.
30013609
FIGURE 9. Simultaneous Keys Pressed
•In order to securely detect and store the key codes of
simultaneous key pressings in the same input row the
following precautions must be taken from the host side:
“As soon as the host device has detected a key pressed event
the host must send the SET_ACTIVE Command with the pa-
rameter set to “00”. This will prevent the LM8322 from enter-
ing HALT mode. If all keyboard events are resolved (no
remaining key pressed status in the LM8322 anymore) then
the host must send the SET_ACTIVE Command again with
the parameter setting the desired duration for the active time.
This will enable the LM8322 to enter low power HALT mode
once the activity time has passed without detecting any
events.
•Once one or more key (pressed and/or released) events
have been read from the host with the help of the READ
FIFO command there are two conditions cleaning the
FIFO buffer contents:
—A second execution of the READ FIFO Command or,
—A new key event detected from the LM8322.
12.3 EXAMPLE KEYPAD CONFIGURATION
Figure 10 shows an 8 × 4 keypad matrix. This configuration
occupies all scanning inputs (KP-X0 through KP-X7) and four
scanning outputs (KP-Y0 through KP-Y3). The remaining
scanning outputs KP-Y4 through KP-Y11 are available for use
as GPIO pins.
15 www.national.com
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
30013610
FIGURE 10. Keypad Interface Example
In the example above, three keys (Up, Down, and Select) are
connected as SF keys (connected directly to ground). Al-
though they could have shared the KP-Xx inputs used with
the scanned keys, the advantage of placing them on their own
KP-Xx inputs is that it allows scanning the keypad while an
SF key is pressed. If an SF key shares a KP-Xx input with any
scanned keys, pressing the SF key prevents the LM8322 from
reading the scanned keys.
The SET_KEY_SIZE command includes a data byte that
specifies the keypad size. The upper 4 bits of the data byte
specify the number of KP-Xx inputs, and the lower 4 bits
specify the number of KP-Yx outputs. The minimum number
of inputs and outputs is 3. Therefore, the minimum keypad
configuration supports 3 × 3 + 3 SF keys (total of 12 keys).
The maximum number of KP-Xx inputs is 8, and the maximum
number of KP-Yx pins is 12. All KP-Xx and KP-Yx pins not
used for the keyboard interface can be used for general-pur-
pose I/O.
For the example shown in Figure 10, the SET_KEY_SIZE
command would specify 8 KP-Xx inputs and 4 KP-Yx outputs.
13.0 General-Purpose I/O Ports
Any unused KP-Xx and KP-Yx pins may be used as general-
purpose I/O (GPIO) port pins. The WRITE_PORT_SEL
(0x85) command selects the port direction, in which a clear
bit in the parameter to the command selects the input direction
and a set bit selects the output direction.
The WRITE_PORT_STATE (0x86) command selects either
the port level when configured as output (by the
WRITE_PORT_SEL command) or when configured as an in-
put selects between a high-impedance input or an input with
a pullup or pulldown device. The selection between pullup or
pulldown devices is controlled by the parameter bytes to the
WRITE_PULL_DOWN (0x84) command. Clear bits in the pa-
rameter bytes select pullup devices, while set bits select
pulldown devices.
Table 7 shows the GPIO port configurations selected by the
bits in the WRITE_PORT_SEL, WRITE_PORT_STATE, and
WRITE_PULL_DOWN command parameters.
TABLE 7. GPIO Port Control Bits
WRITE_PORT_SEL WRITE_PORT_STATE WRITE_PULL_DOWN Description
0 0 x High-Impedance Input
0 1 0 Input with Pullup Device
0 1 1 Input with Pulldown Device
1 0 x Output, Drive Low
1 1 x Output, Drive High
Any pins used as GPIO ports must be configured after the
peripheral configuration has been initialized with the
WRITE_CFG command (0x81) and the keypad configuration
has been initialized with the SET_KEY_SIZE command
(0x90). The default keypad configuration after reset is a 3 × 3
www.national.com 16
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
keyboard matrix. The default GPIO configuration is an input
with the pullup disabled.
13.1 USING THE CONFIG_X PINS FOR GPIO
The CONFIG_1 and CONFIG_2 pins are available for use as
GPIO pins after power-on or reset. However, stable states
must be provided on these pins during power-on or reset to
select the ACCESS.bus (I2C) bus address.
External pullup or pulldown resistors can be used to pull either
CONFIG_x pin low, while retaining the ability to drive it to an-
other state when used as a GPIO pin.
CONFIG_2 has two alternate functions, in addition to GPIO.
It can be configured as a multiplexer output using the
WRITE_CFG command (0x81), in which case it will not be
available as a GPIO pin. It can also be configured as a PWM
output, which also would override its use as a GPIO pin.
13.2 GPIO TIMING
When a WRITE_PORT_STATE command (0x86) is received,
the GPIO outputs do not change to their new states immedi-
ately or simultaneously. The first one changes 54 µs after the
command is acknowledged, and the others change at inter-
vals of 7.3 µs, as shown in Figure 11.
30013611
FIGURE 11. GPIO Port State Change Timing
17 www.national.com
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
14.0 PWM Output Generation
Three pulse-width modulated (PWM) outputs are provided
with advanced capabilities for ramp-up and ramp-down of the
PWM duty cycle and execution of simple to complex com-
mand sequences. These capabilities are supported by three
independent script-execution engines capable of au-
tonomous operation after setup and launch by the host.
Figure 12 shows the architecture of a script-execution engine.
30013612
FIGURE 12. PWM Script Execution Engine
The host has three commands for interfacing to the script ex-
ecution engine. The following commands are always associ-
ated with one particular PWM channel:
•PWM_WRITE — load one word into the script command
file at a specified address.
•PWM_START — start execution of the script.
•PWM_STOP — stop execution of the script.
Please note: The PWM_STOP command might not take im-
mediate effect if the current command being executed is a
command with long execution time. If a PWM_STOP com-
mand is sent when the PWM engine is running a long RAMP
command, the PWM will only stop after the RAMP is com-
pleted.
The script commands have their own fixed-length 16-bit for-
mat and encoding unrelated to the variable-length, byte-
based format used for host commands. A script command is
sent by the host to the LM8322 as a parameter to the
PWM_WRITE command. Another parameter to the
PWM_WRITE command specifies an address in the script
command file for receiving the command.
14.1 COMMAND QUEUE
After the host issues a PWM_START command, script com-
mands are read from the script command file into a command
queue which consists of a command file output register, com-
mand buffer, and active command register. This allows one
command to be active while another command is queued in
the command buffer, which allows seamless back-to-back
command execution.
A command loaded into the command file output register is
synchronized to the 32.768 kHz clock and stored in the com-
mand buffer. If no command is currently active, the command
passes through to the active command register. In this case,
another command can be read from the script command file,
which is queued in the command buffer. On completion of the
currently active command, the contents of the command
buffer are transferred to the active command register, and the
command buffer may then receive a new command.
The host does not have direct access to any of the registers
in the command queue. The operations which read script
commands from the script command file occur automatically
after the host issues the PWM_START command.
Script execution stops when the host sends a PWM_STOP
command or when the script engine executes an END com-
mand with the Reset bit set to 1. Executing an END command
with the Reset bit set to “1” or the reception of a PWM_STOP
command asserts IRQ to the host.
14.2 PWM TIMER OPERATION
The timers implement a fixed 256-cycle period with a pro-
grammable duty cycle and programmable ramp-up/ramp-
down of the duty cycle. Figure 13 shows the architecture of a
PWM timer.
www.national.com 18
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
30013613
FIGURE 13. PWM Timer
The period counter is a free running 8-bit up-counter which
starts counting when the script command file issues the first
RAMP command. An END command stops the period
counter.
The duty cycle of the PWM output is controlled by the ramp
counter. If the PWM period counter is active, the PWM output
signal is asserted while the period counter has a value less
than or equal to the value of the ramp counter.
The ramp counter can increment or decrement at a rate con-
trolled by the prescaler and step time counter. The prescaler
selects a factor of 16 or 512 for dividing down the frequency
of the 32.768 kHz clock. The ramp counter saturates at either
0x00 or 0xFF depending on the ramp direction.
The number of increment or decrement steps is specified by
the INCREMENT field of the RAMP command, which is load-
ed into the step counter. Even if the ramp counter hits its
saturation value, the requested number of steps will be per-
formed. An option enables assertion of the IRQ output to the
host after the last step is performed.
14.3 PWM SCRIPT COMMANDS
Table 8 summarizes the script commands.
TABLE 8. PWM Script Commands
Command 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RAMP 0 PRES
CALE STEPTIME SIGN INCREMENT
SET_PWM 0 1 0 PWMVALUE
GO_TO_ 0
START
BRANCH 1 0 1 LOOPCOUNT 0 ADDRESS
END 1 1 0 0 RESET 0
TRIGGER 1 1 1 WAITTRIGGER SENDTRIGGER 0
19 www.national.com
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
14.4 RAMP COMMAND
The RAMP command generates a duty-cycle ramp starting
from the current value. At each step, the ramp counter is in-
cremented or decremented by one, unless it has reached its
its saturation value (0xFF for increment, or 0x00 for decre-
ment). The time for one step is controlled by the PRESCALE
bit and STEPTIME field. The minimum time for one step is
0.49 milliseconds. and the maximum time is about 1 second,
which supports both very fast and very slow ramps. The IN-
CREMENT field specifies the number of steps to be executed
by the command. The maximum value is 126, which corre-
sponds to half of full scale.
There are two special cases in the instruction encoding. If all
bits and fields are 0, it is interpreted as the GO TO START
command. If the STEPTIME field is 0 but any other bit or field
is non-zero, it is interpreted as the SET_PWM command.
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
0 PRESCALE STEPTIME SIGN INCREMENT
Bit or Field Value Description
PRESCALE 0 Divide the 32.768 kHz clock by 16
1 Divide the 32.768 kHz clock by 512
STEPTIME 1–63 Number of prescaled clock cycles per step
SIGN 0 Increment ramp counter
1 Decrement ramp counter
INCREMENT 1–126 Number of steps executed by this instruction
14.5 SET_PWM COMMAND
The SET_PWM command loads the ramp counter from the
8-bit DUTYCYCLE field in the instruction.
Please note: Only 0x00 and 0xFF are valid values for the duty
cycle in SET_PWM command. Other values can be estab-
lished by initializing the duty cycle to either 100% or 0%
followed by a RAMP command.
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
0 1 0 0 0 0 0 0 DUTYCYCLE
Bit or Field Value Description
DUTYCYCLE 0 Duty cycle is 0%.
255 Duty cycle is 100%.
14.6 GO_TO_START COMMAND
The GO_TO_START command jumps to the first command
in the script command file.
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
0
14.7 BRANCH COMMAND
The BRANCH command jumps to the specified command in
the script command file, with the option of looping for a spec-
ified number of repetitions. Nested loops are not allowed.
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
1 0 1 LOOPCOUNT 0 ADDRESS
Field Value Description
LOOPCOUNT 0 Loop until a STOP PWM SCRIPT command is issued by the host.
1–63 Number of repetitions to perform, biased by -1. The range is 0–62 repetitions.
ADDRESS 0–59 Branch destination address in the script command file. If this field is greater than 59, no
looping will be performed.
www.national.com 20
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
14.8 END COMMAND
The END command terminates script execution and asserts
an interrupt to the host if the RESET bit is set to “1” or “0”.
If the END command is executed with the RESET bit set to
“1” , the PWM output will be disabled. If the RESET bit is “0”
when executing the END command, the PWM channel re-
mains active with the fixed duty cycle it was last set to.
Please note: If a PWM channel is waiting for the trigger (last
executed command was "TRIGGER") and the script execu-
tion is halted then the "END" command can’t be executed
because the previous command is still pending. This is an
exception - in this case the IRQ signal will not be asserted.
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
1 1 0 0 RESET 0
Bit Value Description
RESET 0 PWM_x output is active when script execution terminates.
1 PWM_x output is Tristate when script execution terminates.
14.9 TRIGGER COMMAND
Triggers are used to synchronize operations between PWM
channels. A TRIGGER command that sends a trigger takes
sixteen 32.768 kHz clock cycles, and a command that waits
for a trigger takes at least sixteen 32.768 kHz clock cycles.
A TRIGGER command that waits for a trigger (or triggers) will
stall script execution until the trigger conditions are satisfied.
Then, it will clear the trigger(s) and continue to the next com-
mand.
When a trigger is sent, it is stored by the receiving channel
and can only be cleared when the receiving channel executes
a TRIGGER command that waits for the trigger.
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
1 1 1 WAITTRIGGER SENDTRIGGER 0
Field Value Description
0001xx Wait for trigger from channel 2
WAITTRIGGER 000xx1 Wait for trigger from channel 0
000x1x Wait for trigger from channel 1
SENDTRIGGER
000xx1 Send trigger to channel 0
000x1x Send trigger to channel 1
0001xx Send trigger to channel 2
14.10 PWM SCRIPT EXAMPLE
This example shows a complex ramping sequence that uses
triggers for synchronization. Three scripts implement the ex-
ample. Figure 14 shows the PWM outputs for this example.
30013614
FIGURE 14. PWM Outputs
21 www.national.com
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
14.10.1 PWM Channel 0 Script
Script
Command
Address
PWM_WRITE
Parameter 1
PWM_WRITE
Parameter 2
PWM_WRITE
Parameter 3
Script
Command Description
0x00 0x01 0x40 0x00 SET_PWM Initialize channel for 0% duty cycle
0x01 0x05 0xE2 0x00 TRIGGER Wait for trigger from channel 2
0x02 0x09 0x07 0x7E RAMP Ramp up by 126 steps
0x03 0x0D 0x07 0x7E RAMP Ramp up by 126 steps
0x04 0x11 0x07 0xFE RAMP Ramp down by 126 steps
0x05 0x15 0x07 0xFE RAMP Ramp down by 126 steps
0x06 0x19 0xA1 0x82 BRANCH Loop 2 times starting at address 0x02
0x07 0x1D 0xC8 0x00 END Terminate script and assert IRQ to host
14.10.2 PWM Channel 1 Script
Script
Command
Address
PWM_WRITE
Parameter 1
PWM_WRITE
Parameter 2
PWM_WRITE
Parameter 3
Script
Command Description
0x00 0x02 0x40 0xFF SET_PWM Initialize channel for 100% duty cycle
0x01 0x06 0xE2 0x00 TRIGGER Wait for trigger from channel 2
0x02 0x0A 0x0F 0xFE RAMP Ramp down by 126 steps
0x03 0x0E 0x0F 0xFE RAMP Ramp down by 126 steps
0x04 0x12 0x0F 0x7E RAMP Ramp up by 126 steps
0x05 0x16 0x0F 0x7E RAMP Ramp up by 126 steps
0x06 0x1A 0xA2 0x02 BRANCH Loop 3 times starting at address 0x02
0x07 0x1E 0xE0 0x08 TRIGGER Send trigger to channel 2
0x08 0x22 0xC8 0x00 END Terminate script and assert IRQ to host
14.10.3 PWM Channel 2 Script
Script
Command
Address
PWM_WRITE
Parameter 1
PWM_WRITE
Parameter 2
PWM_WRITE
Parameter 3
Script
Command Description
0x00 0x03 0x40 0x00 SET_PWM Initialize channel for 0% duty cycle
0x01 0x07 0x03 0x7E RAMP Ramp up by 126 steps
0x02 0x0B 0x03 0x7E RAMP Ramp up by 126 steps
0x03 0x0F 0x03 0xFE RAMP Ramp down by 126 steps
0x04 0x13 0x03 0xFE RAMP Ramp down by 126 steps
0x05 0x17 0xE1 0x06 TRIGGER Send triggers to channels 0 and 1,
wait for trigger from channel 1
0x06 0x1B 0x03 0x7E RAMP Ramp up by 126 steps
0x07 0x1F 0x03 0x7E RAMP Ramp up by 126 steps
0x08 0x23 0x03 0xFE RAMP Ramp down by 126 steps
0x09 0x27 0x03 0xFE RAMP Ramp down by 126 steps
0x0A 0x2B 0xC8 0x00 END Terminate script and assert IRQ to host
www.national.com 22
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
14.11 SELECTABLE SCRIPT EXAMPLE
Multiple scripts can be placed in a single buffer. The script
which is executed is selected by the address in the parameter
to the PWM_START command (0x96).
Script
Command
Address
PWM_WRITE
Parameter 1
PWM_WRITE
Parameter 2
PWM_WRITE
Parameter 3
Script
Command Description
0x00
Script 1
0x01 0x40 0x00 Set PWM_0 to 0% duty cycle
0x01 0x05 0x0F 0x33 Ramp up 51 steps
0x02 0x09 0xC0 0x00 Keep channel at 20% duty cycle
0x03
Script 2
0x0D 0x40 0xFF Set PWM_0 to 100% duty cycle
0x04 0x11 0x0F 0xD5 Ramp down 85 steps
0x05 0x15 0xC0 0x00 Keep channel at 66.6% duty cycle
0x06
Script 3
0x19 0x40 0x00 Set PWM_0 to 0% duty cycle
0x07 0x1D 0x07 0x7E Ramp up 126 steps
0x08 0x21 0x07 0x7E Ramp up 126 steps
0x09 0x25 0x07 0xFE Ramp down 126 steps
0x0A 0x29 0x07 0xFE Ramp down 126 steps
0x0B 0x2D 0xA5 0x07 Loop ten times to script address 0x07
0x0C Script 4 0x31 0xC8 0x00 Switch PWM_0 off (script 3 automatically
enters here)
0x0D
Script 5
0x35 0x40 0x00 Set PWM_0 to 0% duty cycle
0x0E 0x39 0x07 0x25 Ramp up 37 steps
0x0F 0x3D 0xC0 0x00 Keep channel at 14.5% duty cycle
0x10 Script 6 0x41 0x40 0x00 Set PWM_0 to 0% duty cycle
0x11
(Alternates
between 25%
and 75% duty
cycle)
0x45 0x01 0x40 Ramp up 64 steps
0x12 0x49 0x3F 0x7E Ramp up 126 steps
0x13 0x4D 0x3F 0xFE Ramp down 126 steps
0x14 0x51 0xA0 0x12 Always branch to script address 0x12
0x15
Script 7
.....
0x3B
To set a fixed duty cycle on a PWM channel requires 3 steps
(see script 1 for duty cycles from 0% to 49% and script 2 for
duty cycles from 51% to 100%).
To keep a PWM channel active providing a fixed duty cycle
on its output, the script must terminate with the END com-
mand leaving the RESET bit clear. To switch this channel off,
the host must send another PWM_START command (0x96
followed by the parameter bytes) triggering the single com-
mand described in script 4. This END command will set the
RESET bit and the dedicated PWM output will be disabled.
Script 3 will automatically enter into this command when the
10 loops of ramping up and down are executed.
Script 7 can be finished by two commands:
•PWM_STOP command with parameter 0x01
•PWM_START command with parameter 0x31 (start
PWM_0 from address 0x0C to run script 4)
The script address is the physical address to be used from
BRANCH instructions inside the script file buffer. The param-
eter 1 byte contains the same address with the 2 channel bits
appended and will be associated with the PWM_START com-
mand.
23 www.national.com
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
15.0 Digital Multiplexers
Two 2:1 multiplexers are provided for host-controlled digital
switching. Setting the MUX1EN or MUX2EN bits with the
WRITE_CFG command enables the corresponding multi-
plexer and its input and output signals, which overrides any
other functions which may use these pins. The MUX1 signals
are alternate functions of the PWM_x outputs. The MUX2
signals are alternate functions of three KP-Yx pins.
The data select inputs for the multiplexers are controlled by
the MUX1SEL and MUX2SEL bits, which are written by the
WRITE_CFG command. If it is important to avoid momentarily
passing an incorrect input to the output, the select bit must be
loaded with a first WRITE_CFG command before sending a
second WRITE_CFG command to set the enable bit. The
truth table for the multiplexers is shown in Table 9.
TABLE 9. Digital Multiplexer Function Table
MUXxE
N Bit
MUXxSEL
Bit
MUXx_IN
2
Pin
MUXx_IN
1
Pin
MUXx_OU
T
Pin
1 0 X 0 0
1 0 X 1 1
1 1 0 X 0
1 1 1 X 1
0 X X X
MUXx_OU
T
not enabled
www.national.com 24
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
16.0 Host Interface
The two-wire ACCESS.bus interface is used to communicate
with a host. The ACCESS.bus interface is fully compliant with
the I2C bus standard. The LM8322 operates as a bus slave
at 400 kHz (Fast mode).
All communication with the LM8322 over the ACCESS.bus
interface is initiated by the host, usually in response to an in-
terrupt request (IRQ low) asserted by the LM8322. The
LM8322 may request service from the host by asserting the
IRQ interrupt output.
16.1 START AND STOP CONDITIONS
Every transfer is preceded by a Start condition or a Repeated
Start condition. The latter occurs when a command follows
immediately upon another command without an intervening
Stop condition. A Stop condition indicates the end of trans-
mission. Every byte is acknowledged by the receiver.
30013615
FIGURE 15. Start and Stop Conditions
16.2 CONTINUOUS COMMAND STRINGS
A host device may send a continuous string of commands
using the Repeated Start condition, which would block an-
other ACCESS.bus device from gaining control of the bus.
After Power-On the host device must send multiple com-
mands to initialize the LM8322 device. A minimal command
string will include the commands shown in Table 10.
TABLE 10. Minimal Command String
Command Description
READ_ID Read vendor ID and software
version
READ_INT Check if NOINT bit is set in
interrupt register
WRITE_CFG Configure the LM8322
SET_KEY_SIZE Set the size of the keypad
WRITE_CLK Set the clock mode for the PWM
unit
WRITE_PORT_SEL Set port direction for GPIO pins
WRITE_PORT_STATE Set port states of GPIO pins
A more comprehensive command string may include the ad-
ditional commands shown in Table 11.
TABLE 11. Additional Commands
Command Description
SET_DEBOUNCE Set debounce time
SET_ACTIVE Set active time
READ_CLK Verify PWM clock settings
READ_CFG Verify configuration setting
READ_PORT_STATE
Read all port states (physical levels
on pins)
Note: Very long continuous command strings exceeding 30
milliseconds could overrun the ability of the LM8322 to pro-
cess commands if the time from the last clock cycle of a
command until the next Start condition or Repeated Start
condition is always shorter than 60 µs. A very long command
chain could prevent the LM8322 from performing any watch-
dog service and consequently could trigger a physical
RESET to the device.
To avoid overrunning the LM8322, the host should not send
a Start condition or a Repeated Start condition less than 100
µs after the last Stop condition or the last clock of a preceding
command.
16.3 DEVICE ADDRESS
The device address is controlled by states sampled on the
CONFIG_1 and CONFIG_2 pins, as shown in Table 12. In the
first byte of a bus transaction, a 7-bit address plus a direction
bit are broadcast by the bus master to all bus slaves.
TABLE 12. Device Address Selection
CONFIG_1 CONFIG_2 Device Address
0 0 1000 010X
0 1 1000 011X
1 0 1000 100X
1 1 1000 101X
If the CONFIG_1 and CONFIG_2 pins are left open, on-chip
pullups will select 1000 101X by default.
16.4 HOST WRITE COMMANDS
Some host commands include one or more data bytes written
to the LM8322. Figure 16 shows a SET_KEY_SIZE com-
mand, which consists of an address byte, a command byte,
and one data byte. The first byte is composed of a 7-bit slave
address in bits 7:1 and a direction bit in bit 0. The state of the
direction bit is 0 on writes from the host to the slave and 1 on
reads from the slave to the host.
The second byte sends the command. The SET_KEY_SIZE
command is 0x90.
The third byte send the data, in this case specifying the num-
ber of rows and columns for the keypad.
25 www.national.com
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
30013616
FIGURE 16. Host Write Command
16.5 HOST READ COMMANDS
Some host commands include one or more data bytes read
from the LM8322. Figure 17 shows a READ_PORT_SEL
command which consists of an address byte, a command
byte, a second address byte, and two data bytes.
The first address byte is sent with the direction bit driven low
to indicate a write transaction of the command to the LM8322.
The second address byte is sent with the direction bit undriven
(pulled high) to indicate a read transaction of the data from
the LM8322.
The Start (or Repeated Start) condition must be repeated
whenever the slave address or the direction bit is changed. In
this case, the direction bit is changed.
The bus master can send any number of Repeated Start con-
ditions without releasing control of the bus. This technique
can be used to implement atomic transactions, in which the
bus master sends a command and then reads a register with-
out allowing any other device to get control of the bus between
these events.
The data is sent from the slave to the host in the fourth and
fifth bytes. The fifth byte ends with a negative acknowledge-
ment (NACK) to indicate the end of the data.
30013617
FIGURE 17. Host Read Command
16.6 INTERRUPTS
The IRQ output may be asserted on these conditions:
•Any new key-event after the last interrupt was asserted but
not yet acknowledged by reading the interrupt code.
•Termination of a PWM script (END command).
•Any error condition, which is indicated by the error code.
www.national.com 26
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
16.7 INTERRUPT CODE
The interrupt code is read and acknowledged with the
READ_INT command (0x82). This command clears the code
and deasserts the IRQ output. Table 13 shows the format of
the interrupt code.
TABLE 13. Interrupt Code
7 6 5 4 3 2 1 0
PWM2END PWM1END PWM0END NOINIT ERROR 0 0 KEYPAD
Bit Description
PWM2END An END script command was executed by PWM channel 2.
PWM1END An END script command was executed by PWM channel 1.
PWM0END An END script command was executed by PWM channel 0.
NOINIT The LM8322 is waiting for an initialization sequence.
ERROR An error condition occurred.
KEYPAD A key-press or key-release event occurred.
16.8 ERROR CODE
If the LM8322 reports an error, the READ_ERROR command
(0x8C) is used to read the error code. This command clears
the error code. Table 14 shows the format of the error code.
TABLE 14. Error Code
7 6 5 4 3 2 1 0
0 FIFOOVR 0 0 0 KEYOVR CMDUNK BADPAR
Bit Description
FIFOOVER Event occurred while the FIFO was full.
KEYOVR More than two keys were pressed simultaneously.
CMDUNK Not a valid command.
BADPAR Bad command parameter.
16.9 WAKE-UP FROM HALT MODE
Any bus transaction initiated by the host may encounter the
LM8322 device in Halt mode or busy with processing data,
such as controlling the FIFO buffer or executing interrupt ser-
vice routines.
Figure 18 shows the case in which the host sends a command
while the LM8322 is in Halt mode (Internal execution clock is
stopped). Any activity on the ACCESS.bus wakes up the
LM8322, but it cannot acknowledge the first bus cycle imme-
diately after wake-up.
The host drives a Start condition followed by seven address
bits and a R/W bit. The host then releases SDA for one clock
period, so that it can be driven by the LM8322.
If the LM8322 does not drive SDA low during the high phase
of the clock period immediately after the R/W bit, the bus cycle
terminates without being acknowledged (shown as NACK in
Figure 18). The host then aborts the transaction by sending
a Stop condition. After aborting the bus cycle, the host may
then retry the bus cycle. On the second attempt, the LM8322
will be able to acknowledge the slave address, because it will
be in Active mode.
Alternatively, the I2C specification allows sending a START
byte (00000001), which will not be acknowledged by any de-
vice. This byte can be used to wake up the LM8322 from Halt
mode. The LM8322 may also stall the bus transaction by
pulling the SCL low, which is a valid behavior defined by the
I2C specification.
27 www.national.com
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
30013618
FIGURE 18. LM8322 Responds with NACK, Host Retries Command
www.national.com 28
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
17.0 Host Commands
Function Cmd Dir Data Bytes Description
READ_ID 0x80 R nnnn nnnn Read the manufacturer code (nnnn nnnn) and the device
revision number (pppp pppp).
pppp pppp
WRITE_CFG 0x81 W nnnn nnnn Write the hardware configuration register.
READ_INT 0x82 R nnnn nnnn
Read the interrupt code, deassert the IRQ output, and clear
the code. (If the NOINIT bit is set, it remains set and IRQ
remains asserted until a WRITE_CFG command is received.
RESET 0x83 W nnnn nnnn Reset the LM8322. Error if nnnn nnnn is not 0xAA.
WRITE_PULL_DO
WN 0x84 W nnnn nnnn Select pullup (0) or pulldown (1) direction for the
corresponding general-purpose I/O (GPIO) port pins.
pppp pppp
WRITE_PORT_SE
L0x85 W nnnn nnnn Select input (0) or output (1) for the corresponding general-
purpose I/O (GPIO) port pins.
pppp pppp
WRITE_PORT_ST
ATE 0x86 W
nnnn nnnn For pins configured as inputs, 0 selects high-impedance
mode and 1 enables a weak pullup. For pins configured as
outputs, each bit specifies the logic level driven on the pin.
pppp pppp
READ_PORT_SEL 0x87 R nnnn nnnn Read the direction of the corresponding GPIO port pins.
pppp pppp
READ_PORT_STA
TE 0x88 R nnnn nnnn Read the state on the corresponding GPIO port pins.
pppp pppp
READ_FIFO 0x89 R Up to 15 event
codes
Read an event from the FIFO.
Maximum of 14 event codes stored in the FIFO.
RPT_READ_FIFO 0x8A R Up to 15 event
codes
Repeats a FIFO read without advancing the FIFO pointer,
for example to retry a read after an error.
SET_ACTIVE 0x8B W nnnn nnnn
Set the time during which the LM8322 stays active before
entering Halt mode. The active time must be greater than the
debounce time. The default time is 500 milliseconds. The
valid range is 1255. Active time = n × 4 milliseconds.
READ_ERROR 0x8C R nnnn nnnn Read and clear the error code.
SET_DEBOUNCE 0x8F W nnnn nnnn
Set the time for rescanning the keypad after detecting a key-
press or key-release event to verify the event. The default
time is 12 milliseconds. The valid range is 1255. Debounce
time = n × 4 milliseconds and must not exceed active time.
SET_KEY_SIZE 0x90 W nnnn pppp Set keypad size. nnnn = KP-Xx pins, pppp = KP-Yx pins
READ_KEY_SIZE 0x91 R nnnn pppp Read keypad size. nnnn = KP-Xx pins, pppp = KP-Yx pins
READ_CFG 0x92 R nnnn nnnn Read the hardware configuration register.
WRITE_CLOCK 0x93 W nnnn nnnn Write the clock configuration register.
READ_CLOCK 0x94 R nnnn nnnn Read the clock configuration register.
PWM_WRITE 0x95 W
aaaa aann Write a command to the PWM script command file.
pppp pppp nn = PWM channel number (01, 10, or 11)
qqqq qqqq aaaaaa = address in script command file (059)
pppp pppp = high byte of script command
qqqq qqqq = low byte of script command
PWM_START 0x96 W aaaa aann Start script on channel nn (01, 10, or 11) at address aaaaaa.
PWM_STOP 0x97 W 0000 00nn Stop script on channel nn (01, 10, or 11).
29 www.national.com
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
Please note: The data bytes which follow the command can
be reads (toward the host) or writes (toward the LM8322). In
the case of the READ_FIFO and RPT_READ_FIFO com-
mands, the number of data bytes is variable, with the last
transaction indicated by returning a negative acknowledge-
ment (NACK).
17.1 READ_ID COMMAND
The READ_ID command consists of a command byte (0x80)
from the host and two data bytes from the LM8322.
The first data byte returns the manufacturer code, and the
second byte returns the device revision level.
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
1 0 0 0 0 0 0 0 MANUFACTURER REVISION
17.2 WRITE_CFG COMMAND
The WRITE_CFG command consists of a command byte
(0x81) and a data byte from the host. The data byte is loaded
into the hardware configuration register. The default state of
this register is 0x80.
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
1 0 0 0 0 0 0 1 IRQPST 0 0 0 MUX2EN MUX2SEL MUX1EN MUX1SEL
Bit Value Description
IRQPST 0 IRQ is an open-drain output.
1 IRQ is a push-pull output.
MUX2EN 0 MUX2_OUT output disabled.
1 MUX2_OUT output enabled. This overrides any other function available on this pin.
MUX2SEL 0 If the MUX2 EN bit is 1, the MUX2_IN1 input drives the MUX2_OUT output.
1 If the MUX2 EN bit is 1, the MUX2_IN2 input drives the MUX2_OUT output.
MUX1EN 0 MUX1_OUT output disabled.
1 MUX1_OUT output enabled. This overrides any other function available on this pin.
MUX1SEL 0 If the MUX1 EN bit is 1, the MUX1_IN1 input drives the MUX1_OUT output.
1 If the MUX1 EN bit is 1, the MUX1_IN2 input drives the MUX1_OUT output.
Please note: The WRITE_CFG COMMAND defines basic
hardware operation characteristics. It should be placed at the
beginning of the initialization sequence driven from the host
device after power on. It is not recommended to change the
configuration during run time. Anytime this command is used,
it initializes important operating characteristics such as the
the GPIO port. This means that the GPIO pins must be re-
established via WRITE_PORT_SEL and
WRITE_PORT_STATE commands in this case.
www.national.com 30
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
17.3 READ_INT COMMAND
The READ_INT command consists of a command byte (0x82)
from the host and a data byte from the LM8322. The data byte
is the interrupt code. Reading the interrupt code acknowl-
edges the interrupt (which deasserts IRQ) and clears the
interrupt code. An exception to this behavior occurs if the
NOINIT bit is set, in which case IRQ will not be deasserted
and the interrupt code will not be cleared until a WRITE_CFG
command is received.
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
1 0 0 0 0 0 1 0 PWM2END PWM1END PWM0END NOINIT ERROR 0 0 KEYPAD
Bit Value Description
PWM2END 0 No interrupt from PWM channel 2.
1 An END script command was executed by PWM channel 2.
PWM1END 0 No interrupt from PWM channel 1.
1 An END script command was executed by PWM channel 1.
PWM0END 0 No interrupt from PWM channel 0.
1 An END script command was executed by PWM channel 0.
NOINIT 0 Normal operation.
1 LM8322 is waiting for the initialization sequence.
ERROR 0 No error condition is indicated.
1 An error condition occurred.
KEYPAD 0 No key-press or key-release event is indicated.
1 A key-press or key-release event occurred.
17.4 RESET COMMAND
The RESET command consists of a command byte (0x83)
and one data byte from the host. The command causes a re-
set, identical to an external reset. The data byte must be
0xAA, otherwise no reset will occur and an error condition will
be signalled.
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
1 0 0 0 0 0 1 1 1 0 1 0 1 0 1 0
31 www.national.com
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
17.5 WRITE_PULL_DOWN COMMAND
The WRITE_PORT_SEL command consists of a command
byte (0x84) and two data bytes from the host. The data bytes
configure the pullup/pulldown device (if enabled) for the cor-
responding general-purpose I/O ports as pullups (0) or pull-
downs (1). The first data byte controls ports GPIO_15 through
GPIO_08, and the second byte controls ports GPIO_07
through GPIO_00.
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
1 0 0 0 0 1 0 1
GPIO_15
GPIO_14
GPIO_13
GPIO_12
GPIO_11
GPIO_10
GPIO_09
GPIO_08
GPIO_07
GPIO_06
GPIO_05
GPIO_04
GPIO_03
GPIO_02
GPIO_01
GPIO_00
Bit Value Description
GPIO_xx 0 GPIO port pin pullup/pulldown device is a pullup.
1 GPIO port pin pullup/pulldown device is a pulldown.
17.6 WRITE_PORT_SEL COMMAND
The WRITE_PORT_SEL command consists of a command
byte (0x85) and two data bytes from the host. The data bytes
configure the corresponding general-purpose I/O ports as in-
puts (0) or outputs (1). The first data byte controls ports
GPIO_15 through GPIO_08, and the second byte controls
ports GPIO_07 through GPIO_00.
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
1 0 0 0 0 1 0 1
GPIO_15
GPIO_14
GPIO_13
GPIO_12
GPIO_11
GPIO_10
0
GPIO_08
GPIO_07
GPIO_06
GPIO_05
GPIO_04
GPIO_03
GPIO_02
GPIO_01
GPIO_00
Bit Value Description
GPIO_xx 0 GPIO port pin is an input.
1 GPIO port pin is an output.
The GPIO_09 port pin can only be configured as an input with
weak pullup/pulldown device.
www.national.com 32
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
17.7 WRITE_PORT_STATE COMMAND
The WRITE_PORT_STATE command consists of a com-
mand byte (0x86) and two data bytes from the host. For
general-purpose I/O ports configured as inputs, the data
bytes select whether the inputs are high-impedance (0) or
have a weak pullup (1). For ports configured as outputs, the
data bytes control the state driven on the output. The first data
byte controls ports GPIO_15 through GPIO_08, and the sec-
ond byte controls ports GPIO_07 through GPIO_00.
Bit Value Description
GPIO_xx
0If the GPIO port pin is an input, pullup/pulldown device is disabled. If the GPIO port
pin is an output, it is driven low.
1If the GPIO port pin is an input, pullup/pulldown device is enabled. If the GPIO port
pin is an output, it is driven high.
17.8 READ_PORT_SEL COMMAND
The READ_PORT_SEL command consists of a command
byte (0x87) from the host and two data bytes from the
LM8322. The data bytes indicate the direction configured for
the corresponding ports, either input (0) or output (1). The first
data byte controls ports GPIO_15 through GPIO_08, and the
second byte controls ports GPIO_07 through GPIO_00.
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
1 0 0 0 0 1 1 1
GPIO_15
GPIO_14
GPIO_13
GPIO_12
GPIO_11
GPIO_10
GPIO_09
GPIO_08
GPIO_07
GPIO_06
GPIO_05
GPIO_04
GPIO_03
GPIO_02
GPIO_01
GPIO_00
Bit Value Description
GPIO_xx 0 GPIO port pin is an input.
1 GPIO port pin is an output.
33 www.national.com
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
17.9 READ_PORT_STATE COMMAND
The READ_PORT_STATE command consists of a command
byte (0x88) from the host and two data bytes from the
LM8322. The data bytes indicate the states on the corre-
sponding ports. The first data byte controls ports GPIO_15
through GPIO_08, and the second byte controls ports
GPIO_07 through GPIO_00.
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
1 0 0 0 1 0 0 0
GPIO_15
GPIO_14
GPIO_13
GPIO_12
GPIO_11
GPIO_10
GPIO_09
GPIO_08
GP
IO_
07
GPIO_06
GPIO_05
GPIO_04
GPIO_03
GPIO_02
GPIO_01
GPIO_00
Bit Value Description
GPIO_xx
0If the GPIO port pin is an input, pullup is disabled. If the GPIO port pin is an
output, it is driven low.
1If the GPIO port pin is an input, pullup is enabled. If the GPIO port pin is an
output, it is driven high.
17.10 READ_FIFO COMMAND
The READ_FIFO command consists of a command byte
(0x89) sent from the host and a variable number of data bytes
received from the LM8322. The LM8322 will provide data until
the FIFO is empty. The last data byte is indicated by its value
(0x00) and a negative acknowledgement (NACK) on the
ACCESS.bus interface. The data bytes correspond to key-
press and key-release events, as described in Table 5.
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
1 0 0 0 1 0 0 1 FIFODATA 0x00
Field Value Description
FIFODATA 0xxxxxxx Key-release event.
1xxxxxxx Key-press event.
17.11 RPT_READ_FIFO COMMAND
The RPT_READ_FIFO command consists of a command
byte (0x8A) and from the host and a variable number of data
bytes from the LM8322. This command provides the same
data as a previous READ_FIFO command, but without ad-
vancing the FIFO pointer. It may be used to recover from an
error encountered during a READ_FIFO command.
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
1 0 0 0 1 0 1 0 FIFODATA 0x00
Field Value Description
FIFODATA 0xxxxxxx Key-release event.
1xxxxxxx Key-press event.
www.national.com 34
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
17.12 SET_ACTIVE COMMAND
The SET_ACTIVE command consists of a command byte
(0x8B) and a data byte from the host. This command sets the
time that the LM8322 stays active without detecting a key-
press or key-release event before entering Halt mode. The
default active time is 500 milliseconds. The host can program
ACTIVETIME from 4–1020 milliseconds with a granularity of
4 milliseconds.
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
1 0 0 0 1 0 1 1 ACTIVETIME
Field Value Description
ACTIVETIME 0 Halt mode is disabled.
1–255 Active time = n × 4 milliseconds.
17.13 READ_ERROR COMMAND
The READ_ERROR command consists of a command byte
(0x8C) from the host and a data byte from the LM8322. After
reading an interrupt code that indicates an error condition, this
command is used to read an error code that indicates the
cause of the error condition.
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
1 0 0 0 1 1 0 0 0 FIFOOVR 0 0 0 KEYOVR CMDUNK BADPAR
Bit Value Description
FIFOOVR 0 No FIFO overrun occurred.
1 Event occurred while the FIFO was full.
KEYOVR 0 No keypad overrun occurred.
1 More than two keys were pressed simultaneously.
CMDUNK 0 No invalid command was encountered.
1 Not a valid command.
BADPAR 0 No bad parameter was encountered.
1 Bad command parameter.
35 www.national.com
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
17.14 SET_DEBOUNCE COMMAND
The SET_DEBOUNCE command consists of a command
byte (0x8F) and a data byte from the host. This command sets
the time that the LM8322 waits before rescanning the keypad
to confirm a key-press or key-release event. The default de-
bounce time is 12 milliseconds. The host can program DE-
BOUNCETIME from 4–1020 milliseconds with a granularity
of 4 milliseconds. The DEBOUNCETIME must not exceed the
active time set with the SET_ACTIVE command.
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
1 0 0 0 1 1 1 1 DEBOUNCETIME
Field Value Description
DEBOUNCETIME 1–255 Active time = n × 4 milliseconds.
17.15 SET_KEY_SIZE COMMAND
The SET_KEY_SIZE command consists of a command byte
(0x90) and a data byte from the host. This command specifies
the keypad size in terms of the number of KP-Xx inputs and
KP-Yx outputs which are used. Any unused KP-Xx and KP-
Yx pins may be used for general-purpose I/O. The minimum
value for either field is 3, which corresponds to a keypad con-
figuration that supports 3 × 3 + 3 SF keys (total of 12 keys).
The maximum number of KP-Xx inputs is 8, and the maximum
number of KP-Yx outputs is 12. If the digital multiplexer MUX2
is used, the maximum number of KP-Yx outputs is 9. If the
SLOWCLKOUT pin is used, the maximum number is 8.
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
1 0 0 1 0 0 0 0 KP-X KP-Y
Field Value Description
KP-X 3–8 Number of KP-Xx inputs.
KP-Y 3–12 Number of KP-Yx outputs.
17.16 READ_KEY_SIZE COMMAND
The READ_KEY_SIZE command consists of a command
byte (0x91) from the host and a data byte from the LM8322.
The host can issue the command at any time to read the con-
figuration of the keypad.
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
1 0 0 1 0 0 0 1 KP-X KP-Y
Field Value Description
KP-X 3–8 Number of KP-Xx inputs.
KP-Y 3–12 Number of KP-Yx outputs.
www.national.com 36
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
17.17 READ_CFG COMMAND
The READ_CFG command consists of a command byte
(0x92) from the host and a data byte from the LM8322. The
data byte returns the settings in the hardware configuration
register. The default state of this register is 0x80.
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
1 0 0 1 0 0 1 0 0 0 0 0
MUX2EN
MUX2SEL
MUX1EN
MUX1SEL
Bit Value Description
MUX2EN 0 MUX2_OUT output disabled.
1 MUX2_OUT output enabled. This overrides any other function available on this pin.
MUX2SEL 0 If the MUX2 EN bit is 1, the MUX2_IN1 input drives the MUX2_OUT output.
1 If the MUX2 EN bit is 1, the MUX2_IN2 input drives the MUX2_OUT output.
MUX1EN 0 MUX1_OUT output disabled.
1 MUX1_OUT output enabled. This overrides any other function available on this pin.
MUX1SEL 0 If the MUX1 EN bit is 1, the MUX1_IN1 input drives the MUX1_OUT output.
1 If the MUX1 EN bit is 1, the MUX1_IN2 input drives the MUX1_OUT output.
17.18 WRITE_CLOCK COMMAND
The WRITE_CLOCK command consists of a command byte
(0x93) and a data byte from the host. This command sets the
clock configuration, as described in Table 2, Section 9.3
CLOCK CONFIGURATION.
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
1 0 0 1 0 0 1 1 CONFIGURATION
17.19 READ_CLOCK COMMAND
The READ_CLOCK command consists of a command byte
(0x94) from the host and a data byte from the LM8322. This
command reads bits 7:2 of the clock configuration, as de-
scribed in Table 2 , Section 9.3 CLOCK CONFIGURATION.
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
1 0 0 1 0 1 0 0 CONFIGURATION 1 0
37 www.national.com
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
17.20 PWM_WRITE COMMAND
The PWM_WRITE command consists of a command byte
(0x95) and three data bytes from the host. The command
writes a 16-bit script command into a specified address in the
script command file of the specified PWM channel.
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
1 0 0 1 0 1 0 1 ADDRESS CH COMMAND
Bit Value Description
ADDRESS 0–59 Location in the PWM script command file.
CH
01 PWM channel 0.
10 PWM channel 1.
11 PWM channel 2.
17.21 PWM_START COMMAND
The PWM_START command consists of a command byte
(0x96) and a data byte from the host. This command starts
execution of the script command file at the specified address
for the specified channel.
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
1 0 0 1 0 1 1 0 ADDRESS CH
Bit Value Description
ADDRESS 0–59 Start address in the PWM script command file.
CH
01 PWM channel 0.
10 PWM channel 1.
11 PWM channel 2.
17.22 PWM_STOP COMMAND
The PWM_STOP command consists of a command byte
(0x97) and a data byte from the host. This command stops
execution of the script command file for the specified channel.
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
1 0 0 1 0 1 1 1 0 0 0 0 0 0 CH
Bit Value Description
CH
01 PWM channel 0.
10 PWM channel 1.
11 PWM channel 2.
www.national.com 38
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
18.0 Absolute Maximum Ratings (Note
1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Supply Voltage (VCC)2V
Voltage at Any Pin -0.3V to VCC +0.3V
Maximum Input Current Without
Latchup ±100 mA
ESD Protection Level
(Human Body Model) 2 kV
(Machine Model) 200V
(Charge Device Model) 750V
Total Current into VCC Pin (Source) 100 mA
Total Current out of GND Pin (Sink) 100 mA
Storage Temperature Range −65°C to +140°C
19.0 DC Electrical Characteristics
(Temperature: -40°C ≤ TA ≤ +85°C)
Data sheet specification limits are guaranteed by design, test, or statistical analysis.
Symbol Parameter Conditions Min Typ Max Units
VCC Operating Voltage 1.62 1.98 V
IDD Supply Current (Note 2) Internal Clock,
1.9 3.0 mA
No loads on pins,
VCC = 1.9V, TC = 0.5µs (Note 4)
IHALT Standby Mode Current (Note 5)Typical:
VCC = 1.9V, TA = 25°C <9 40 µA
VIL Logical 0 Input Voltage (Note 5) 0.3 x VCC V
VIH Logical 1 Input Voltage (Note 5) 0.7 x VCC V
Hi-Z Input Leakage (TRI-STATE Output) VCC = 1.8V -2 2 µA
Port Input Hysteresis (Note 5, Note 6) 100 400 mA
Weak Pull-Up/Pull-Down Current 1.6V<VCC< 2.0V 150 µA
Output Current Source (Push-Pull Mode) VCC = 1.62V, VOH = 0.7 x VCC -16 mA
Output CurrentSink (Push-Pull Mode) VCC = 1.62V, VOL = 0.3 x VCC 16 mA
Allowable Sink and Source Current per Pin (Note
7)
16 mA
CPAD Input Capacitance (Note 7) 5 pF
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and test conditions, see the Electrical Characteristics tables.
Note 2: Supply current is measured with inputs connected to VCC and outputs driven low but not connected to a load.
Note 3: TC = instruction cycle time (min. 0.7 µs).
Note 4: In standby mode, the internal clock is switched off. Supply current in standby mode is measured with inputs connected to VCC and outputs driven low but
not connected to a load.
Note 5: Applied to all digital pins (including RESET) except for SLOWCLK when configured for an external clock..
Note 6: Guaranteed by design, not tested.
Note 7: The sum of all I/O sink/source current must not e4xceed the maximum total current into VCC and out of GND as specified in the absolute maximem
ratings.
39 www.national.com
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
20.0 AC Electrical Characteristics
(Temperature: -40°C ≤ TA ≤ +85°C)
Data sheet specification limits are guaranteed by design, test, or statistical analysis.
Parameter Conditions Min Typ Max Units
System Clock (mclk) (Note 8) Internal RC 21 MHz
1.62V ≤ VCC ≤ 1.98V
Processing and Command Execution Cycle (tC)
(Note 8)
1.62V ≤ VCC ≤ 1.98V 0.5 μs
System Clock, Processing and Command
Execution Cycle Variation(Note 8)
7 %
General-Purpose I/O (GPIO)
Output Rise Time(Note 8) CLOAD = 50 pF 15 ns
Output Fall Time(Note 8) 15 ns
ACCESS.bus Input Signals(Note 9)
Bus Free Time Between Stop and Start
Condition (tBUFi) (Note 8)
tSCLhigho
SCL Setup Time (tCSTOsi) (Note 8) Before Stop Condition k 8 mclk
SCL Hold Time (tCSTRhi) (Note 8) After Start Condition 8 mclk
SCL Setup Time (tCSTRsi) (Note 8) Before Start Condition 8 mclk
Data High Setup Time (tDHCsi) (Note 8) Before SCL Rising Edge (RE) 2 mclk
Data Low Setup Time (tDLCsi) (Note 8) Before SCL RE 2 mclk
SCL Low Time (tSCLlowi) (Note 8) After SCL Falling Edge (FE) 12 mclk
SCL High Time (tSCLhighi) (Note 8) After SCL RE 12 mclk
SDA Hold Time (tSDAhi) (Note 8) After SCL FE 0 mclk
SDA Setup Time (tSDAsi) (Note 8) Before SCL RE 2 mclk
ACCESS.bus Output Signals (Note 9)
Bus Free Time Between Stop and Start
Condition (tBUFo)(Note 9)
tSCLhigho
SCL Setup Time (tCSTOso) (Note 8) Before Stop Condition tSCLhigho
SCL Hold Time (tCSTRho) (Note 8) After Start Condition tSCLhigho
SCL Setup Time (tCSTRso) (Note 8) Before Start Condition tSCLhigho
Data High Setup Time (tDHCso) (Note 8) Before SCL RE tSCLhigho
Data Low Setup Time (tDLCso) (Note 8) Before SCL RE tSCLhigho
SCL Low Time (tSCLlowo) (Note 8) After SCL FE 16 mclk
SCL High Time (tSCLhigho) (Note 8) After SCL RE 16 mclk
SDA Hold Time (tSDAho) (Note 8) After SCL FE 7 mclk
SDA Valid Time (tSDAso) (Note 8) Before SCL RE 7 mclk
Note 8: Guaranteed by design, not tested.
Note 9: The ACCESS.bus interface implements and meets the timing necessary for interface to the I2C and SMBus protocol at logic levels. The bus drivers are
designed with open-drain output for bidirectional operation. The will not meet the AC timing and current/voltage requirements of the full bus specification.
www.national.com 40
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
30013619
FIGURE 19. ACB Start and Stop Condition Timing
41 www.national.com
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
21.0 Physical Dimensions inches (millimeters) unless otherwise noted
Micro Array Package
Order Number LM8322GGR8
NS Package Number GRA36A
www.national.com 42
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
Notes
43 www.national.com
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:29
LM8322
Notes
LM8322 Mobile I/O Companion Supporting Key-Scan, I/O Expansion, PWM, and ACCESS.bus
Host Interface
For more National Semiconductor product information and proven design tools, visit the following Web sites at:
www.national.com
Products Design Support
Amplifiers www.national.com/amplifiers WEBENCH® Tools www.national.com/webench
Audio www.national.com/audio App Notes www.national.com/appnotes
Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns
Data Converters www.national.com/adc Samples www.national.com/samples
Interface www.national.com/interface Eval Boards www.national.com/evalboards
LVDS www.national.com/lvds Packaging www.national.com/packaging
Power Management www.national.com/power Green Compliance www.national.com/quality/green
Switching Regulators www.national.com/switchers Distributors www.national.com/contacts
LDOs www.national.com/ldo Quality and Reliability www.national.com/quality
LED Lighting www.national.com/led Feedback/Support www.national.com/feedback
Voltage References www.national.com/vref Design Made Easy www.national.com/easy
PowerWise® Solutions www.national.com/powerwise Applications & Markets www.national.com/solutions
Serial Digital Interface (SDI) www.national.com/sdi Mil/Aero www.national.com/milaero
Temperature Sensors www.national.com/tempsensors SolarMagic™ www.national.com/solarmagic
PLL/VCO www.national.com/wireless PowerWise® Design
University
www.national.com/training
THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION
(“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY
OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO
SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS,
IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS
DOCUMENT.
TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT
NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL
PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR
APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND
APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE
NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS.
EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO
LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE
AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR
PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY
RIGHT.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR
SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and
whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected
to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform
can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness.
National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other
brand or product names may be trademarks or registered trademarks of their respective holders.
Copyright© 2011 National Semiconductor Corporation
For the most current product information visit us at www.national.com
National Semiconductor
Americas Technical
Support Center
Email: support@nsc.com
Tel: 1-800-272-9959
National Semiconductor Europe
Technical Support Center
Email: europe.support@nsc.com
National Semiconductor Asia
Pacific Technical Support Center
Email: ap.support@nsc.com
National Semiconductor Japan
Technical Support Center
Email: jpn.feedback@nsc.com
www.national.com
300136 Version 7 Revision 2 Print Date/Time: 2011/10/04 16:24:30
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic."Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products Applications
Audio www.ti.com/audio Communications and Telecom www.ti.com/communications
Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers
Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps
DLP®Products www.dlp.com Energy and Lighting www.ti.com/energy
DSP dsp.ti.com Industrial www.ti.com/industrial
Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical
Interface interface.ti.com Security www.ti.com/security
Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community Home Page e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright ©2011, Texas Instruments Incorporated
