MAX660 MAX660 Switched Capacitor Voltage Converter Literature Number: SNOS405 MAX660 Switched Capacitor Voltage Converter General Description Features The MAX660 CMOS charge-pump voltage converter inverts a positive voltage in the range of 1.5V to 5.5V to the corresponding negative voltage. The MAX660 uses two low cost capacitors to provide 100 mA of output current without the cost, size, and EMI related to inductor based converters. With an operating current of only 120 A and operating efficiency greater than 90% at most loads, the MAX660 provides ideal performance for battery powered systems. The MAX660 may also be used as a positive voltage doubler. The oscillator frequency can be lowered by adding an external capacitor to the OSC pin. Also, the OSC pin may be used to drive the MAX660 with an external clock. A frequency control (FC) pin selects the oscillator frequency of 10 kHz or 80 kHz. n n n n n Inverts or doubles input supply voltage Narrow SO-8 Package 6.5 typical output resistance 88% typical conversion efficiency at 100 mA Selectable oscillator frequency: 10 kHz/80 kHz Applications n n n n n n Laptop computers Cellular phones Medical instruments Operational amplifier power supplies Interface power supplies Handheld instruments Typical Application Circuits Positive Voltage Doubler Voltage Inverter DS100898-1 DS100898-2 Connection Diagram 8-Lead SO DS100898-5 Top View Ordering Information Order Number Top Mark Package MAX660M Date Code MAX660M M08A Rail (95 units/rail) MAX660MX Date Code MAX660M M08A Tape and Reel (2500 units/rail) (c) 1999 National Semiconductor Corporation DS100898 Supplied as www.national.com MAX660 Switched Capacitor Voltage Converter November 1999 MAX660 Absolute Maximum Ratings (Note 1) Power Dissipation (TA = 25C) (Note 3) TJ Max (Note 3) JA (Note 3) Operating Junction Temp. Range Storage Temperature Range Lead Temperature (Soldering, 10 seconds) ESD Rating If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage (V+ to GND, or GND to OUT) 6V LV (OUT - 0.3V) to (GND + 3V) FC, OSC The least negative of (OUT - 0.3V) or (V+ - 6V) to (V+ + 0.3V) V+ and OUT Continuous Output Current 120 mA Output Short-Circuit Duration to GND (Note 2) 1 sec. 735 mW 150C 170C/W -40C to +85C -65C to +150C 300C 2 kV Electrical Characteristics Limits in standard typeface are for TJ = 25C, and limits in boldface type apply over the full operating temperature range. Unless otherwise specified: V+ = 5V, FC = Open, C1 = C2 = 150 F. (Note 4) Symbol V+ IQ IL ROUT FOSC IOSC PEFF VOEFF Parameter Supply Voltage Supply Current Condition RL = 1k Inverter, LV = Open (Note 5) Inverter, LV = GND Doubler, LV = OUT Min 1.5 5.5 2.5 5.5 Output Current TA +85C, OUT -4V 100 100 Output Resistance (Note 6) TA > +85C, OUT -3.8V IL = 100 mA TA +85C Oscillator Frequency OSC Input Current Power Efficiency Voltage Conversion Efficiency OSC = Open 0.12 0.5 1 3 6.5 5 10 FC = V+ 40 80 10 12 2 16 FC = Open FC = V+ Units V mA mA TA > +85C FC = Open + Max 5.5 FC = Open FC = V+ No Load LV = Open Typ 3.5 RL (1k) between V and OUT 96 98 RL (500) between GND and OUT IL = 100 mA to GND 92 96 No Load 99 kHz A % 88 99.96 % Note 1: Absolute maximum ratings indicate limits beyond which damage to the device may occur. Electrical specifications do not apply when operating the device beyond its rated operating conditions. Note 2: OUT may be shorted to GND for one second without damage. However, shorting OUT to V+ may damage the device and should be avoided. Also, for temperatures above 85C, OUT must not be shorted to GND or V+, or device may be damaged. Note 3: The maximum allowable power dissipation is calculated by using PDMax = (TJMax - TA)/JA, where TJMax is the maximum junction temperature, TA is the ambient temperature, and JA is the junction-to-ambient thermal resistance of the specified package. Note 4: In the test circuit, capacitors C1 and C2 are 0.2 maximum ESR capacitors. Capacitors with higher ESR will increase output resistance, reduce output voltage and efficiency. Note 5: The minimum limit for this parameter is different from the limit of 3.0V for the industry-standard "660" product. For inverter operation with supply voltage below 3.5V, connect the LV pin to GND. Note 6: Specified output resistance includes internal switch resistance and capacitor ESR. www.national.com 2 MAX660 Test Circuit DS100898-4 FIGURE 1. MAX660 Test Circuit Typical Performance Characteristics Supply Current vs Supply Voltage (Circuit of Figure 1) Supply Current vs Oscillator Frequency DS100898-36 Output Source Resistance vs Temperature Output Source Resistance vs Supply Voltage DS100898-38 DS100898-37 Efficiency vs Load Load Current DS100898-39 Output Voltage Drop vs Load Current DS100898-40 3 DS100898-41 www.national.com MAX660 Typical Performance Characteristics Efficiency vs Oscillator Frequency (Circuit of Figure 1) (Continued) Output Voltage vs Oscillator Frequency DS100898-13 Oscillator Frequency Supply Voltage (FC = V+) DS100898-14 Oscillator Frequency vs Supply Voltage (FC = Open) DS100898-16 DS100898-19 4 DS100898-15 Oscillator Frequency vs Temperature (FC = V+) DS100898-17 Oscillator Frequency vs Temperature (FC = Open) www.national.com Oscillator Frequency vs External Capacitance DS100898-18 MAX660 Pin Description Pin Name Function Voltage Inverter 1 FC Voltage Doubler Frequency control for internal oscillator: FC = open, fOSC = 10 kHz (typ); Same as inverter. FC = V+, fOSC = 80 kHz (typ); FC has no effect when OSC pin is driven externally. 2 CAP+ Connect this pin to the positive terminal of charge-pump capacitor. Same as inverter. 3 GND Power supply ground input. Power supply positive voltage input. 4 CAP- Connect this pin to the negative terminal of charge-pump capacitor. Same as inverter. 5 OUT Negative voltage output. Power supply ground input. 6 LV Low-voltage operation input. Tie LV to GND when input voltage is less than 3.5V. Above 3.5V, LV can be connected to GND or left open. When driving OSC with an external clock, LV must be connected to GND. LV must be tied to OUT. 7 OSC Oscillator control input. OSC is connected to an internal 15 pF capacitor. An external capacitor can be connected to slow the oscillator. Also, an external clock can be used to drive OSC. Same as inverter except that OSC cannot be driven by an external clock. 8 V+ Power supply positive voltage input. Positive voltage output. Circuit Description Application Information The MAX660 contains four large CMOS switches which are switched in a sequence to invert the input supply voltage. Energy transfer and storage are provided by external capacitors. Figure 2 illustrates the voltage conversion scheme. When S1 and S3 are closed, C1 charges to the supply voltage V+. During this time interval switches S2 and S4 are open. In the second time interval, S1 and S3 are open and S2 and S4 are closed, C1 is charging C2. After a number of cycles, the voltage across C2 will be pumped to V+. Since the anode of C2 is connected to ground, the output at the cathode of C2 equals -(V+) assuming no load on C2, no loss in the switches, and no ESR in the capacitors. In reality, the charge transfer efficiency depends on the switching frequency, the on-resistance of the switches, and the ESR of the capacitors. SIMPLE NEGATIVE VOLTAGE CONVERTER The main application of MAX660 is to generate a negative supply voltage. The voltage inverter circuit uses only two external capacitors as shown in the Typical Application Circuits. The range of the input supply voltage is 1.5V to 5.5V. For a supply voltage less than 3.5V, the LV pin must be connected to ground to bypass the internal regulator circuitry. This gives the best performance in low voltage applications. If the supply voltage is greater than 3.5V, LV may be connected to ground or left open. The choice of leaving LV open simplifies the direct substitution of the MAX660 for the LMC7660 Switched Capacitor Voltage Converter. The output characteristics of this circuit can be approximated by an ideal voltage source in series with a resistor. The voltage source equals -(V+). The output resistance Rout is a function of the ON resistance of the internal MOS switches, the oscillator frequency, and the capacitance and ESR of C1 and C2. A good approximation is: where RSW is the sum of the ON resistance of the internal MOS switches shown in Figure 2. High value, low ESR capacitors will reduce the output resistance. Instead of increasing the capacitance, the oscillator frequency can be increased to reduce the 2/(fosc x C1) term. Once this term is trivial compared with RSW and ESRs, further increasing in oscillator frequency and capacitance will become ineffective. The peak-to-peak output voltage ripple is determined by the oscillator frequency, and the capacitance and ESR of the output capacitor C2: DS100898-21 FIGURE 2. Voltage Inverting Principle 5 www.national.com MAX660 Application Information lows smaller capacitors to be used for equivalent output resistance and ripple, but increases the typical supply current from 0.12 mA to 1 mA. (Continued) The oscillator frequency can be lowered by adding an external capacitor between OSC and GND. (See Typical Performance Characteristics.) Also, in the inverter mode, an external clock that swings within 100 mV of V+ and GND can be used to drive OSC. Any CMOS logic gate is suitable for driving OSC. LV must be grounded when driving OSC. The maximum external clock frequency is limited to 150 kHz. Again, using a low ESR capacitor will result in lower ripple. POSITIVE VOLTAGE DOUBLER The MAX660 can operate as a positive voltage doubler (as shown in the Typical Application Circuits). The doubling function is achieved by reversing some of the connections to the device. The input voltage is applied to the GND pin with an allowable voltage from 2.5V to 5.5V. The V+ pin is used as the output. The LV pin and OUT pin must be connected to ground. The OSC pin can not be driven by an external clock in this operation mode. The unloaded output voltage is twice of the input voltage and is not reduced by the diode D1's forward drop. The switching frequency of the converter (also called the charge pump frequency) is half of the oscillator frequency. Note: OSC cannot be driven by an external clock in the voltage-doubling mode. TABLE 1. MAX660 Oscillator Frequency Selection The Schottky diode D1 is only needed for start-up. The internal oscillator circuit uses the V+ pin and the LV pin (connected to ground in the voltage doubler circuit) as its power rails. Voltage across V+ and LV must be larger than 1.5V to insure the operation of the oscillator. During start-up, D1 is used to charge up the voltage at V+ pin to start the oscillator; also, it protects the device from turning-on its own parasitic diode and potentially latching-up. Therefore, the Schottky diode D1 should have enough current carrying capability to charge the output capacitor at start-up, as well as a low forward voltage to prevent the internal parasitic diode from turning-on. A Schottky diode like 1N5817 can be used for most applications. If the input voltage ramp is less than 10V/ms, a smaller Schottky diode like MBR0520LT1 can be used to reduce the circuit size. OSC Open Open Oscillator 10 kHz V+ Open 80 kHz Open or V+ External Capacitor See Typical Performance Characteristics N/A External Clock (inverter mode only) External Clock Frequency CAPACITOR SELECTION As discussed in the Simple Negative Voltage Converter section, the output resistance and ripple voltage are dependent on the capacitance and ESR values of the external capacitors. The output voltage drop is the load current times the output resistance, and the power efficiency is SPLIT V+ IN HALF Another interesting application shown in the Basic Application Circuits is using the MAX660 as a precision voltage divider. Since the off-voltage across each switch equals VIN/2, the input voltage can be raised to +11V. Where IQ(V+) is the quiescent power loss of the IC device, and IL2ROUT is the conversion loss associated with the switch on-resistance, the two external capacitors and their ESRs. Since the switching current charging and discharging C1 is approximately twice as the output current, the effect of the ESR of the pumping capacitor C1 is multiplied by four in the output resistance. The output capacitor C2 is charging and discharging at a current approximately equal to the output current, therefore, its ESR only counts once in the output resistance. However, the ESR of C2 directly affects the output voltage ripple. Therefore, low ESR capacitors (Table 2) are recommended for both capacitors to maximize efficiency, reduce the output voltage drop and voltage ripple. For convenience, C1 and C2 are usually chosen to be the same. The output resistance varies with the oscillator frequency and the capacitors. In Figure 4, the output resistance vs. oscillator frequency curves are drawn for three different tantalum capacitors. At very low frequency range, capacitance plays the most important role in determining the output resistance. Once the frequency is increased to some point (such as 20 kHz for the 150 F capacitors), the output resistance is dominated by the ON resistance of the internal switches and the ESRs of the external capacitors. A low value, smaller size capacitor usually has a higher ESR compared with a bigger size capacitor of the same type. For lower ESR, use ceramic capacitors. DS100898-3 FIGURE 3. Splitting VIN in Half CHANGING OSCILLATOR FREQUENCY The internal oscillator frequency can be selected using the Frequency Control (FC) pin. When FC is open, the oscillator frequency is 10 kHz; when FC is connected to V+, the frequency increases to 80 kHz. A higher oscillator frequency al- www.national.com FC 6 MAX660 Application Information (Continued) DS100898-32 FIGURE 4. Output Source Resistance vs Oscillator Frequency TABLE 2. Low ESR Capacitor Manufacturers Manufacturer Phone FAX Nichicon Corp. (708)-843-7500 (708)-843-2798 PL, PF series, through-hole aluminum electrolytic Capacitor Type AVX Corp. (803)-448-9411 (803)-448-1943 TPS series, surface-mount tantalum Sprague (207)-324-4140 (207)-324-7223 593D, 594D, 595D series, surface-mount tantalum Sanyo (619)-661-6835 (619)-661-1055 OS-CON series, through-hole aluminum electrolytic Other Applications PARALLELING DEVICES Any number of MAX660s can be paralleled to reduce the output resistance. Each device must have its own pumping capacitor C1, while only one output capacitor Cout is needed as shown in Figure 5. The composite output resistance is: DS100898-7 FIGURE 5. Lowering Output Resistance by Paralleling Devices CASCADING DEVICES Cascading the is an easy way to produce a greater negative voltage (as shown in Figure 6). If n is the integer representing the number of devices cascaded, the unloaded output voltage Vout is (-nVin). The effective output resistance is equal to the weighted sum of each individual device: 7 www.national.com MAX660 Other Applications (Continued) A three-stage cascade circuit shown in Figure 7 generates -3Vin, from Vin. Cascading is also possible when devices are operating in doubling mode. In Figure 8, two devices are cascaded to generate 3Vin. An example of using the circuit in Figure 7 or Figure 8 is generating +15V or -15V from a +5V input. Note that the number of n is practically limited since the increasing of n significantly reduces the efficiency and increases the output resistance and output voltage ripple. DS100898-8 FIGURE 6. Increasing Output Voltage by Cascading Devices DS100898-9 FIGURE 7. Generating -3Vin from +Vin DS100898-10 FIGURE 8. Generating +3Vin from +Vin REGULATING Vout It is possible to regulate the output of the MAX660 by use of a low dropout regulator (such as LP2951). The whole converter is depicted in Figure 9. This converter can give a regulated output from -1.5V to -5.5V by choosing the proper resistor ratio: where Vref = 1.235V. www.national.com 8 (Continued) DS100898-11 FIGURE 9. Combining MAX660 with LP2951 to Make a Negative Adjustable Regulator Also, as shown in Figure 10 by operating MAX660 in voltage doubling mode and adding a linear regulator (such as LP2981) at the output, we can get +5V output from an input as low as +3V. DS100898-12 FIGURE 10. Generating +5V from +3V Input Voltage 9 www.national.com MAX660 Other Applications The error flag on pin 5 of the LP2951 goes low when the regulated output at pin 4 drops by about 5%. The LP2951 can be shutdown by taking pin 3 high. MAX660 Other Applications (Continued) OTHER SWITCHED-CAPACITOR CONVERTERS Please refer to Table 3, which shows National's Switched-Capacitor Converter products. TABLE 3. Switched-Capacitor Converters LM2664 LM2665 LM3350 LM3351 SOT23-6 SOT23-6 Mini SO-8 Mini SO-8 SO-8 0.22 0.22 3.75 1.1 0.12 at 10kHz, 1.0 at 80kHz Output (typ.) 12 12 4.2 4.2 6.5 Oscillator (kHz) 80 80 800 200 10, 80 1.8 to 5.5 1.8 to 5.5 2.5 to 6.25 2.5 to 6.25 1.8 to 5.5 Invert Double 3/2, 2/3 3/2, 2/3 Invert, Double Package Supply Current (typ., mA) Input (V) Output Mode(s) LM2660 LM2661 LM2662 LM2663 Mini SO-8, SO-8 Mini SO-8, SO-8 SO-8 SO-8 0.12 at 10kHz, 1.0 at 80kHz 1.0 0.3 at 10kHz, 1.3 at 70kHz 1.3 Output (typ.) 6.5 6.5 3.5 3.5 Oscillator (kHz) 10, 80 80 10, 70 70 1.8 to 5.5 1.8 to 5.5 1.8 to 5.5 1.8 to 5.5 Invert, Double Invert, Double Invert, Double Invert, Double Package Supply Current (typ., mA) Input (V) Output Mode(s) www.national.com 10 MAX660 MAX660 Switched Capacitor Voltage Converter Physical Dimensions inches (millimeters) unless otherwise noted 8-Lead SO (M) Order Number MAX660M NS Package Number M08A LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: support@nsc.com www.national.com National Semiconductor Europe Fax: +49 (0) 1 80-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 1 80-530 85 85 English Tel: +49 (0) 1 80-532 78 32 Francais Tel: +49 (0) 1 80-532 93 58 Italiano Tel: +49 (0) 1 80-534 16 80 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: sea.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated