Order this document by MBR150/D SEMICONDUCTOR TECHNICAL DATA . . . employing the Schottky Barrier principle in a large area metal-to-silicon power diode. State-of-the-art geometry features epitaxial construction with oxide passivation and metal overlap contact. Ideally suited for use as rectifiers in low-voltage, high-frequency inverters, free wheeling diodes, and polarity protection diodes. * * * * MBR160 is a Motorola Preferred Device Low Reverse Current Low Stored Charge, Majority Carrier Conduction Low Power Loss/High Efficiency Highly Stable Oxide Passivated Junction SCHOTTKY BARRIER RECTIFIERS 1 AMPERE 50, 60 VOLTS Mechanical Characteristics: * Case: Epoxy, Molded * Weight: 0.4 gram (approximately) * Finish: All External Surfaces Corrosion Resistant and Terminal Leads are Readily Solderable * Lead and Mounting Surface Temperature for Soldering Purposes: 220C Max. for 10 Seconds, 1/16 from case * Shipped in plastic bags, 1000 per bag * Available Tape and Reeled, 5000 per reel, by adding a "RL'' suffix to the part number * Polarity: Cathode Indicated by Polarity Band * Marking: B150, B160 CASE 59-04 PLASTIC MAXIMUM RATINGS Rating Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage RMS Reverse Voltage Average Rectified Forward Current (2) (VR(equiv) 0.2 VR(dc), TL = 90C, RJA = 80C/W, P.C. Board Mounting, see Note 3, TA = 55C) v Nonrepetitive Peak Surge Current (Surge applied at rated load conditions, halfwave, single phase, 60 Hz, TL = 70C) Operating and Storage Junction Temperature Range (Reverse Voltage applied) Peak Operating Junction Temperature (Forward Current applied) Symbol MBR150 MBR160 Unit VRRM VRWM VR 50 60 Volts VR(RMS) 35 42 Volts IO 1 Amp IFSM 25 (for one cycle) Amps TJ, Tstg *65 to +150 C TJ(pk) 150 C Symbol Max Unit RJA 80 C/W Symbol Max Unit THERMAL CHARACTERISTICS (Notes 3 and 4) Characteristic Thermal Resistance, Junction to Ambient ELECTRICAL CHARACTERISTICS (TL = 25C unless otherwise noted) (2) Characteristic Maximum Instantaneous Forward Voltage (1) (iF = 0.1 A) (iF = 1 A) (iF = 3 A) vF Maximum Instantaneous Reverse Current @ Rated dc Voltage (1) (TL = 25C) (TL = 100C) iR Volt 0.550 0.750 1.000 mA 0.5 5 (1) Pulse Test: Pulse Width = 300 s, Duty Cycle 2.0%. (2) Lead Temperature reference is cathode lead 1/32 from case. Preferred devices are Motorola recommended choices for future use and best overall value. Rev 1 Device Rectifier Motorola, Inc. 1996 Data 1 10 10 TJ = 150C 5.0 TJ = 150C 100C I R , REVERSE CURRENT (mA) 7.0 25C 5.0 3.0 1.0 100C 0.5 0.2 0.1 75C 0.05 0.02 0.01 25C 0.005 0.002 0.001 0.7 10 0 20 30 50 40 VR, REVERSE VOLTAGE (VOLTS) 0.5 60 70 Figure 2. Typical Reverse Current* *The curves shown are typical for the highest voltage device in the voltage grouping. Typical reverse current for lower voltage selections can be estimated from these same curves if VR is sufficiently below rated VR. 0.3 0.2 5.0 0.1 PF(AV) , AVERAGE FORWARD POWER DISSIPATION (WATTS) i F, INSTANTANEOUS FORWARD CURRENT (AMPS) 2.0 125C 2.0 1.0 0.07 0.05 0.03 0.02 0 SQUARE WAVE 4.0 3.0 dc 2.0 5 p 10 IPK/IAV = 20 1.0 0 0.2 0.4 0.6 0.8 1.0 1.2 0 1.6 1.4 1.0 3.0 2.0 4.0 5.0 vF, INSTANTANEOUS VOLTAGE (VOLTS) IF(AV), AVERAGE FORWARD CURRENT (AMPS) Figure 1. Typical Forward Voltage Figure 3. Forward Power Dissipation THERMAL CHARACTERISTICS r(t), TRANSIENT THERMAL RESISTANCE (NORMALIZED) 1.0 0.7 0.5 ZJL(t) = ZJL * r(t) 0.3 0.2 tp 0.1 Ppk Ppk TIME 0.07 0.05 DUTY CYCLE, D = tp/t1 PEAK POWER, Ppk, is peak of an equivalent square power pulse. t1 TJL = Ppk * RJL [D + (1 - D) * r(t1 + tp) + r(tp) - r(t1)] where TJL = the increase in junction temperature above the lead temperature r(t) = normalized value of transient thermal resistance at time, t, from Figure 4, i.e.: r(t) = r(t1 + tp) = normalized value of transient thermal resistance at time, t1 + tp. 0.03 0.02 0.01 0.1 0.2 0.5 1.0 2.0 5.0 10 20 50 100 200 500 1k 2k 5k 10 k t, TIME (ms) Figure 4. Thermal Response 2 Rectifier Device Data 90 200 BOTH LEADS TO HEAT SINK, EQUAL LENGTH TJ = 25C f = 1 MHz 70 C, CAPACITANCE (pF) R qJL , THERMAL RESISTANCE, JUNCTION-TO-LEAD ( C/W) 80 60 MAXIMUM 50 TYPICAL 40 30 100 80 70 60 50 40 30 20 10 20 1/8 0 1/4 3/8 1/2 5/8 7/8 3/4 1.0 10 0 20 30 40 50 60 70 80 L, LEAD LENGTH (INCHES) VR, REVERSE VOLTAGE (VOLTS) Figure 5. Steady-State Thermal Resistance Figure 6. Typical Capacitance NOTE 3 -- MOUNTING DATA: Data shown for thermal resistance junction-to-ambient (RJA) for the mounting shown is to be used as a typical guideline values for preliminary engineering or in case the tie point temperature cannot be measured. Mounting Method 1 P.C. Board with 1-1/2 x 1-1/2 copper surface. E E EEEEEEE E E E EEEEEEEE EEEEEEEE L Typical Values for RJA in Still Air Lead Length, L (in) Mounting g Method 1/8 1/4 1/2 3/4 1 52 65 72 85 C/W 2 67 80 87 100 C/W 3 -- RJA C/W 50 L Mounting Method 2 L 90 100 Mounting Method 3 P.C. Board with 1-1/2 x 1-1/2 copper surface. L = 3/8 BOARD GROUND PLANE L VECTOR PIN MOUNTING NOTE 4 -- THERMAL CIRCUIT MODEL: (For heat conduction through the leads) RS(A) RL(A) RJ(A) TA(A) RL(K) RJ(K) RS(K) TA(K) PD TL(A) TC(A) TJ TC(K) TL(K) Use of the above model permits junction to lead thermal resistance for any mounting configuration to be found. For a given total lead length, lowest values occur when one side of the rectifier is brought as close as possible to the heat sink. Terms in the model signify: TA = Ambient Temperature TC = Case Temperature TL = Lead Temperature TJ = Junction Temperature RS = Thermal Resistance, Heat Sink to Ambient RL = Thermal Resistance, Lead to Heat Sink RJ = Thermal Resistance, Junction to Case PD = Power Dissipation Rectifier Device Data (Subscripts A and K refer to anode and cathode sides, respectively.) Values for thermal resistance components are: RL = 100C/W/in typically and 120C/W/in maximum. RJ = 36C/W typically and 46C/W maximum. NOTE 5 -- HIGH FREQUENCY OPERATION: Since current flow in a Schottky rectifier is the result of majority carrier conduction, it is not subject to junction diode forward and reverse recovery transients due to minority carrier injection and stored charge. Satisfactory circuit analysis work may be performed by using a model consisting of an ideal diode in parallel with a variable capacitance. (See Figure 6.) Rectification efficiency measurements show that operation will be satisfactory up to several megahertz. For example, relative waveform rectification efficiency is approximately 70 percent at 2 MHz, e.g., the ratio of dc power to RMS power in the load is 0.28 at this frequency, whereas perfect rectification would yield 0.406 for sine wave inputs. However, in contrast to ordinary junction diodes, the loss in waveform efficiency is not indicative of power loss: it is simply a result of reverse current flow through the diode capacitance, which lowers the dc output voltage. 3 PACKAGE DIMENSIONS NOTES: 1. ALL RULES AND NOTES ASSOCIATED WITH JEDEC DO-41 OUTLINE SHALL APPLY. 2. POLARITY DENOTED BY CATHODE BAND. 3. LEAD DIAMETER NOT CONTROLLED WITHIN F DIMENSION. B K D DIM A B D K A MILLIMETERS MIN MAX 5.97 6.60 2.79 3.05 0.76 0.86 27.94 --- INCHES MIN MAX 0.235 0.260 0.110 0.120 0.030 0.034 1.100 --- K CASE 59-04 ISSUE M Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. Mfax is a trademark of Motorola, Inc. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 5405, Denver, Colorado 80217. 303-675-2140 or 1-800-441-2447 JAPAN: Nippon Motorola Ltd.: SPD, Strategic Planning Office, 4-32-1, Nishi-Gotanda, Shinagawa-ku, Tokyo 141, Japan. 81-3-5487-8488 Mfax: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, - US & Canada ONLY 1-800-774-1848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298 INTERNET: http://motorola.com/sps 4 CODELINE TO BE PLACED HERE Rectifier Device Data MBR150/D