 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
1
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
DOutput Swing Includes Both Supply Rails
DLow Noise ...9 nV/Hz Typ at f = 1 kHz
DLow Input Bias Current ...1 pA Typ
DFully Specified for Both Single-Supply and
Split-Supply Operation
DCommon-Mode Input Voltage Range
Includes Negative Rail
DHigh-Gain Bandwidth . . . 2.2 MHz Typ
DHigh Slew Rate . . . 3.6 V/µs Typ
DLow Input Offset Voltage
950 µV Max at TA = 25°C
DMacromodel Included
DPerformance Upgrades for the TS272,
TS274, TLC272, and TLC274
DAvailable in Q-Temp Automotive
HighRel Automotive Applications
Configuration Control / Print Support
Qualification to Automotive Standards
description
The TLC2272 and TLC2274 are dual and
quadruple operational amplifiers from Texas
Instruments. Both devices exhibit rail-to-rail
output performance for increased dynamic range
in single- or split-supply applications. The
TLC227x family offers 2 MHz of bandwidth and
3 V/µs of slew rate for higher speed applications.
These devices offer comparable ac performance
while having better noise, input offset voltage, and
power dissipation than existing CMOS
operational amplifiers. The TLC227x has a noise
voltage of 9 nV/Hz, two times lower than
competitive solutions.
The TLC227x, exhibiting high input impedance
and low noise, is excellent for small-signal
conditioning for high-impedance sources, such as
piezoelectric transducers. Because of the micro-
power dissipation levels, these devices work well
in hand-held monitoring and remote-sensing
applications. In addition, the rail-to-rail output
feature, with single- or split-supplies, makes this
family a great choice when interfacing with analog-to-digital converters (ADCs). For precision applications, the
TLC227xA family is available with a maximum input offset voltage of 950 µV. This family is fully characterized
at 5 V and ±5 V.
The TLC2272/4 also makes great upgrades to the TLC272/4 or TS272/4 in standard designs. They offer
increased output dynamic range, lower noise voltage, and lower input of fset voltage. This enhanced feature set
allows them to be used in a wider range of applications. For applications that require higher output drive and
wider input voltage range, see the TLV2432 and TLV2442 devices.
If the design requires single amplifiers, see the TLV2211/21/31 family. These devices are single rail-to-rail
operational amplifiers in the SOT-23 package. Their small size and low power consumption, make them ideal
for high density, battery-powered equipment.
Copyright 2004, Texas Instruments Incorporated
  !" # $" #  %$&'" "(
$"# ! " #%"# % ") "!#  # #"$!"#
#" *"+( $" %##, # " ##'+ '$
"#",  '' %!"#(
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Advanced LinCMOS is a trademark of Texas Instruments.
|VDD±| − Supply Voltage − V
10
8
6
446 8
12
14
16
10 12 14 16
MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE
vs
SUPPLY VOLTAGE
TA = 25°C
IO = ±50 µA
IO = ±500 µA
V(OPP) − Maximum Peak-to-Peak Output Voltage − VVO(PP)
 %$"# !%'" " -./-/ '' %!"#  "#"
$'## ")*# "(  '' ") %$"# %$"
%##, # " ##'+ '$ "#",  '' %!"#(
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
2POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TLC2272 AVAILABLE OPTIONS
PACKAGED DEVICES
TAVIOmax
At 25°CSMALL
OUTLINE
(D)
CERAMIC
LCC
(FK)
CERAMIC
DIP
(JG)
PLASTIC DIP
(P) TSSOP
(PW)
CERAMIC
FLAT PACK
(U)
0°C to 70°C
950 µV
TLC2272ACD
TLC2272ACP
TLC2272ACPW
0°C to 70°C
950 µV
2.5 mV
TLC2272ACD
TLC2272CD
TLC2272ACP
TLC2272CP TLC2272CPW
950 µV
TLC2272AID
TLC2272AIP
−40°C to 125°C
950 µV
2.5 mV
TLC2272AID
TLC2272ID
TLC2272AIP
TLC2272IP TLC2272IPW
−40
°
C to 125
°
C
950 µV
TLC2272AQD
TLC2272AQPW
950 µV
2.5 mV
TLC2272AQD
TLC2272QD
TLC2272AQPW
TLC2272QPW
−55°C to 125°C
950 µV
TLC2272AMD
TLC2272AMFK
TLC2272AMJG
TLC2272AMP
TLC2272AMU
−55
°
C to 125
°
C
950 µV
2.5 mV
TLC2272AMD
TLC2272MD
TLC2272AMFK
TLC2272MFK
TLC2272AMJG
TLC2272MJG
TLC2272AMP
TLC2272MP
TLC2272AMU
TLC2272MU
The D packages are available taped and reeled. Add R suffix to the device type (e.g., TLC2272CDR).
The PW package is available taped and reeled. Add R suffix to the device type (e.g., TLC2272PWR).
§Chips are tested at 25°C.
TLC2274 AVAILABLE OPTIONS
PACKAGED DEVICES
TAVIOmax
AT 25°CSMALL
OUTLINE
(D)
CERAMIC
LCC
(FK)
CERAMIC
DIP
(J)
PLASTIC
DIP
(N)
TSSOP
(PW)
CERAMIC
FLAT PACK
(W)
0°C to 70°C
950 µV
TLC2274ACD
TLC2274ACN
TLC2274ACPW
0°C to 70°C
950 µV
2.5 mV
TLC2274ACD
TLC2274CD
TLC2274ACN
TLC2274CN
TLC2274ACPW
TLC2274CPW
950 µV
TLC2274AID
TLC2274AIN
TLC2274AIPW
−40°C to 125°C
950 µV
2.5 mV
TLC2274AID
TLC2274ID
TLC2274AIN
TLC2274IN
TLC2274AIPW
TLC2274IPW
−40°C to 125°C
950 µV
TLC2274AQD
950 µV
2.5 mV
TLC2274AQD
TLC2274QD
−55°C to 125°C
950 µV
TLC2274AMD
TLC2274AMFK
TLC2274AMJ
TLC2274AMN
TLC2274AMW
−55
°
C to 125
°
C
950 µV
2.5 mV
TLC2274AMD
TLC2274MD
TLC2274AMFK
TLC2274MFK
TLC2274AMJ
TLC2274MJ
TLC2274AMN
TLC2274MN
TLC2274AMW
TLC2274MW
The D packages are available taped and reeled. Add R suffix to device type (e.g., TLC2274CDR).
The PW package is available taped and reeled.
§Chips are tested at 25°C.
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
3
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
1
2
3
4
8
7
6
5
1OUT
1IN
1IN+
VDD/GND
VDD+
2OUT
2IN
2IN+
TLC2272
D, JG, P, OR PW PACKAGE
(TOP VIEW)
1
2
3
4
5
6
7
14
13
12
11
10
9
8
1OUT
1IN
1IN+
VDD+
2IN+
2IN
2OUT
4OUT
4IN
4IN+
VDD
3IN+
3IN
3OUT
3212019
910111213
4
5
6
7
8
18
17
16
15
14
4IN+
NC
VDD
NC
3IN+
1IN+
NC
VDD+
NC
2IN+
1IN −
1OUT
NC
3IN − 4IN −
2IN −
2OUT
NC
NC − No internal connection
3OUT 4OUT
TLC2274
D, J, N, PW, OR W PACKAGE
(TOP VIEW)
TLC2274
FK PACKAGE
(TOP VIEW)
3212019
910111213
4
5
6
7
8
18
17
16
15
14
NC
2 OUT
NC
2 IN−
NC
NC
1 IN−
NC
1 IN+
NC
NC
1OUT
NC
NC NC
NC
V /GND
NC
2 IN+ V
TLC2272
FK PACKAGE
(TOP VIEW)
DD−
DD+
1
2
3
4
5
10
9
8
7
6
NC
1 OUT
1 IN−
1 IN+
VDD−/GND
NC
VDD+
2 OUT
2 IN−
2 IN+
TLC2272
U PACKAGE
(TOP VIEW)
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
4POST OFFICE BOX 655303 DALLAS, TEXAS 75265
equivalent schematic (each amplifier)
Q3 Q6 Q9 Q12 Q14 Q16
Q2 Q5 Q7 Q8 Q10 Q11
D1
Q17Q15Q13
Q4Q1
R5
C1
VDD+
IN+
IN
R3 R4 R1 R2
OUT
VDD−
ACTUAL DEVICE COMPONENT COUNT
COMPONENT TLC2272 TLC2274
Transistors 38 76
Resistors 26 52
Diodes 9 18
Capacitors 3 6
Includes both amplifiers and all ESD, bias, and trim circuitry
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
5
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Supply voltage, VDD+ (see Note 1) 8 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supply voltage, VDD (see Note 1) 8 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Differential input voltage, VID (see Note 2) ±16 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input voltage range, VI (any input, see Note 1) VDD− − 0.3 V to VDD+
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input current, II (any input) ±5 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output current, IO ±50 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Total current into VDD+ ±50 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Total current out of VDD ±50 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Duration of short-circuit current at (or below) 25°C (see Note 3) unlimited. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Package thermal impedance, θJA (see Notes 4 and 5): D package (8 pin) 97.1°C/W. . . . . . . . . . . . . . . . . . . .
D package (14 pin) 86.2°C/W. . . . . . . . . . . . . . . . . . .
N package 79.7°C/W. . . . . . . . . . . . . . . . . . . . . . . . . .
P package 84.6°C/W. . . . . . . . . . . . . . . . . . . . . . . . . .
PW package (8 pin) 149°C/W. . . . . . . . . . . . . . . . . . .
PW package (14 pin) 113°C/W. . . . . . . . . . . . . . . . . .
Package thermal impedance, θJC (see Notes 4 and 5): FK package 5.6°C/W. . . . . . . . . . . . . . . . . . . . . . . . . . .
J package 15.1°C/W. . . . . . . . . . . . . . . . . . . . . . . . . .
U package 14.7°C/W. . . . . . . . . . . . . . . . . . . . . . . . . .
Operating free-air temperature range, TA: C suffix 0°C to 70°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I, Q suffix 40°C to 125°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
M suffix 55 °C to 125°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature range 65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: D, N, P or PW package 260°C. . . . . . . . . .
Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds: J or U package 300°C. . . . . . . . . . . . . . . . .
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values, except differential voltages, are with respect to the midpoint between VDD+ and VDD .
2. Differential voltages are at IN+ with respect to IN−. Excessive current will flow if input is brought below VDD − 0.3 V.
3. The output may be shorted to either supply. Temperature and/or supply voltages must be limited to ensure that the maximum
dissipation rating is not exceeded.
4. Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable
ambient temperature is PD = (TJ(max) − TA)/θJA. Operating at the absolute maximum TJ of 150°C can affect reliability.
5. The package thermal impedance is calculated in accordance with JESD 51-7 (plastic) or MIL-STD-883 Method 1012 (ceramic).
recommended operating conditions
C SUFFIX I SUFFIX Q SUFFIX M SUFFIX
UNIT
MIN MAX MIN MAX MIN MAX MIN MAX
UNIT
Supply voltage, VDD±±2.2 ±8±2.2 ±8±2.2 ±8±2.2 ±8 V
Input voltage, VIVDD VDD+1.5 VDD VDD+1.5 VDD VDD+1.5 VDD VDD+1.5 V
Common-mode input voltage, VIC VDD VDD+1.5 VDD VDD+1.5 VDD VDD+1.5 VDD VDD+1.5 V
Operating free-air temperature, TA0 70 −40 125 −40 125 −55 125 °C
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
6POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TLC2272C electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
TA
TLC2272C TLC2272AC
UNIT
PARAMETER
TEST CONDITIONS
T
A
MIN TYP MAX MIN TYP MAX
UNIT
Input offset voltage
25°C 300 2500 300 950
µV
IO
Input offset voltage
Full range 3000 1500 µ
V
Temperature coefficient
25
°
C
2
2
µV/°C
αVIO
Temperature coefficient
of input offset voltage
V = 0 V,
25 C
to 70°C
2
2
µ
V/
°
C
Input offset voltage
long-term drift
(see Note 4)
VIC = 0 V,
VDD± = ±2.5 V
,
VO = 0 V,
RS = 50
25°C 0.002 0.002 µV/mo
Input offset current
RS = 50
25°C 0.5 60 0.5 60
pA
IO
Input offset current
Full range 100 100
pA
Input bias current
25°C 1 60 1 60
pA
IB
Input bias current
Full range 100 100
pA
25°C
0 to 4
−0.3
0 to 4
−0.3
Common-mode input
RS = 50 Ω|VIO |≤5 mV
25
°
C
0 to 4
−0.3
to 4.2
0 to 4
−0.3
to 4.2
V
ICR
Common-mode input
voltage
R
S
= 50
Ω, |
V
IO
| ≤
5 mV
Full range
0 to
0 to
V
voltage
RS = 50 ,|VIO |5 mV
Full range
0 to
3.5
0 to
3.5
V
Full range
3.5 3.5
IOH = −20 µA 25°C 4.99 4.99
High-level output
IOH = −200 µA
25°C 4.85 4.93 4.85 4.93
V
High-level output
voltage
I
OH
= −200
µ
A
Full range 4.85 4.85 V
voltage
IOH = −1 mA
25°C 4.25 4.65 4.25 4.65
V
I
OH
= −1 mA
Full range 4.25 4.25
VIC = 2.5 V, IOL = 50 µA 25°C 0.01 0.01
VIC = 2.5 V,
IOL = 500 µA
25°C 0.09 0.15 0.09 0.15
V
Low-level output voltage
V
IC
= 2.5 V,
I
OL
= 500
µ
A
Full range 0.15 0.15 V
Low-level output voltage
VIC = 2.5 V,
IOL = 5 mA
25°C 0.9 1.5 0.9 1.5
V
V
IC
= 2.5 V,
I
OL
= 5
m
A
Full range 1.5 1.5
Large-signal differential
VIC = 2.5 V,
RL = 10 k
25°C 15 35 15 35
A
Large-signal differentia
l
voltage amplification
VIC = 2.5 V,
VO = 1 V to 4 V
RL = 10 k
Full range 15 15 V/mV
voltage amplification
V
O
= 1 V to 4 V
RL = 1 m25°C 175 175
V/mV
rid Differential input
resistance 25°C 1012 1012
riCommon-mode input
resistance 25°C 1012 1012
ciCommon-mode input
capacitance f = 10 kHz, P package 25°C 8 8 pF
zoClosed-loop output
impedance f = 1 MHz, AV = 10 25°C 140 140
Common-mode
VIC = 0 V to 2.7 V,
25°C 70 75 70 75
dB
Common-mode
rejection ratio
VIC = 0 V to 2.7 V,
VO = 2.5 V, RS = 50 Full range 70 70
dB
Supply-voltage
rejection ratio
VDD = 4.4 V to 16 V,VIC = VDD/2,
25°C 80 95 80 95
dB
SVR
rejection ratio
(V
DD
/V
IO
)
VDD = 4.4 V to 16 V,VIC = VDD/2,
No load Full range 80 80
dB
Supply current
VO = 2.5 V,
No load
25°C 2.2 3 2.2 3
mA
IDD Supply current VO = 2.5 V, No load Full range 3 3 mA
Full range is 0°C to 70°C.
Referenced to 0 V
NOTE 6: Typical values are based on the input of fset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
7
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TLC2272C operating characteristics at specified free-air temperature, VDD = 5 V
PARAMETER
TEST CONDITIONS
TA
TLC2272C TLC2272AC
UNIT
PARAMETER
TEST CONDITIONS
TA
MIN TYP MAX MIN TYP MAX
UNIT
Slew rate at unity
V
O
= 0.5 V to 2.5 V,
R = 10 k , C = 100 pF
25°C 2.3 3.6 2.3 3.6
SR
Slew rate at unity
gain
VO = 0.5 V to 2.5 V,
RL = 10 k, CL = 100 pF
Full
1.7
1.7
V/µs
SR
gain
RL = 10 k , CL = 100 pF
Full
range 1.7 1.7
V/µs
Vn
Equivalent input
f = 10 Hz 25°C 50 50
nV/Hz
Vn
Equivalent input
noise voltage f = 1 kHz 25°C 9 9
nV/Hz
VNPP
Peak-to-peak
equivalent input
f = 0.1 Hz to 1 Hz 25°C 1 1
V
VNPP
equivalent input
noise voltage f = 0.1 Hz to 10 Hz 25°C 1.4 1.4 µV
InEquivalent input
noise current 25°C 0.6 0.6 fA/Hz
Total harmonic
VO = 0.5 V to 2.5 V,
AV = 1 0.0013% 0.0013%
THD + N Total harmonic
distortion plus noise
VO = 0.5 V to 2.5 V,
f = 20 kHz,
R = 10 k ,
AV = 10 25°C0.004% 0.004%
THD + N
distortion plus noise
f = 20 kHz,
RL = 10 k,AV = 100
25 C
0.03% 0.03%
Gain-bandwidth
product f = 10 kHz,
CL = 100 pFRL = 10 k,25°C 2.18 2.18 MHz
BOM Maximum
output-swing
bandwidth
VO(PP) = 2 V,
RL = 10 k,AV = 1,
CL = 100 pF25°C 1 1 MHz
AV = −1,
To 0.1%
1.5
1.5
ts
Settling time
AV = −1,
Step = 0.5 V to 2.5 V,
To 0.1%
25°C
1.5 1.5
s
tsSettling time
Step = 0.5 V to 2.5 V,
R
L
= 10 k,
To 0.01%
25°C
2.6
2.6
µs
s
RL = 10 k,
C
L
= 100 pFTo 0.01% 2.6 2.6
φmPhase margin at
unity gain
RL = 10 k
,
CL = 100 pF
25°C50°50°
Gain margin
RL = 10 k,
CL = 100 pF
25°C 10 10 dB
Full range is 0°C to 70°C.
Referenced to 0 V
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
8POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TLC2272C electrical characteristics at specified free-air temperature, VDD± = ±5 V (unless
otherwise specified)
PARAMETER
TEST CONDITIONS
TA
TLC2272C TLC2272AC
UNIT
PARAMETER
TEST CONDITIONS
T
A
MIN TYP MAX MIN TYP MAX
UNIT
Input offset voltage
25°C 300 2500 300 950
µV
IO
Input offset voltage
Full range 3000 1500 µ
V
Temperature coefficient of
25
°
C
2
2
µV/°C
αVIO
Temperature coefficient of
input offset voltage
25 C
to 70°C
2
2
µ
V/
°
C
Input offset voltage
long-term drift
(see Note 4) VIC = 0 V,
RS = 50 VO = 0 V, 25°C0.002 0.002 µV/mo
Input offset current
25°C 0.5 60 0.5 60
pA
IO
Input offset current
Full range 100 100
pA
Input bias current
25°C 1 60 1 60
pA
IB
Input bias current
Full range 100 100
pA
−5
5.3
−5
5.3
25
°
C
−5
to
5.3
to
−5
to
5.3
to
Common-mode input
RS = 50
|VIO |≤5 mV
25 C
to
4
to
4.2
to
4
to
4.2
V
ICR
Common-mode input
voltage
R
S
= 50
Ω, |
V
IO
| ≤
5 mV
−5
−5
V
voltage
Full range
−5
to
−5
to
Full range
to
3.5
to
3.5
IO = −20 µA 25°C 4.99 4.99
Maximum positive peak
IO = −200 µA
25°C 4.85 4.93 4.85 4.93
V
Maximum positive peak
output voltage
I
O
= −200
µ
A
Full range 4.85 4.85 V
output voltage
IO = −1 mA
25°C 4.25 4.65 4.25 4.65
V
I
O
= −1 mA
Full range 4.25 4.25
VIC = 0 V, IO = 50 µA 25°C 4.99 4.99
Maximum negative peak
VIC = 0 V,
IO = 500 µA
25°C 4.85 4.91 4.85 4.91
V
Maximum negative peak
output voltage
V
IC
= 0 V,
I
O
= 500
µ
A
Full range 4.85 4.85 V
output voltage
VIC = 0 V,
IO = 5 mA
25°C 3.5 4.1 3.5 4.1
V
V
IC
= 0 V,
I
O
= 5
m
A
Full range 3.5 3.5
Large-signal differential
RL = 10 k
25°C 25 50 25 50
A
Large-signal differential
voltage amplification
V
O
= ±4 V
R
L
= 10 k
Full range 25 25 V/mV
voltage amplification
VO = ±4 V
RL = 1 m25°C 300 300
V/mV
rid Differential input
resistance 25°C 1012 1012
riCommon-mode input
resistance 25°C 1012 1012
ciCommon-mode input
capacitance f = 10 kHz, P package 25°C 8 8 pF
zoClosed-loop output
impedance f = 1 MHz, AV = 10 25°C 130 130
Common-mode rejection
VIC = −5 V to 2.7 V,
25°C 75 80 75 80
dB
Common-mode rejection
ratio
VIC = −5 V to 2.7 V,
VO = 0 V, RS = 50 Full range 75 75
dB
Supply-voltage rejection
VDD± = 2.2 V to
±
8 V,
25°C 80 95 80 95
dB
SVR
Supply-voltage rejection
ratio (VDD± /VIO)
VDD± = 2.2 V to ±8 V,
VIC = 0 V, No load Full range 80 80
dB
Supply current
VO = 0 V
No load
25°C 2.4 3 2.4 3
mA
IDD Supply current VO = 0 V No load Full range 3 3 mA
Full range is 0°C to 70°C.
NOTE 4: Typical values are based on the input of fset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
9
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TLC2272C operating characteristics at specified free-air temperature, VDD± = ±5 V
PARAMETER
TEST CONDITIONS
TA
TLC2272C TLC2272AC
UNIT
PARAMETER
TEST CONDITIONS
TA
MIN TYP MAX MIN TYP MAX
UNIT
Slew rate at
VO = ±2.3 V,
RL = 10 k,
25°C 2.3 3.6 2.3 3.6
SR Slew rate at
unity gain
VO = ±2.3 V,
CL = 100 pF
RL = 10 k,
Full
1.7
1.7
V/µs
SR
unity gain
CL = 100 pF
Full
range 1.7 1.7
V/µs
Vn
Equivalent input
f = 10 Hz 25°C 50 50
nV/Hz
Vn
Equivalent input
noise voltage f = 1 kHz 25°C 9 9
nV/
Hz
VNPP
Peak-to-peak
equivalent input
f = 0.1 Hz to 1 Hz 25°C 1 1
V
VNPP
equivalent input
noise voltage f = 0.1 Hz to 10 Hz 25°C 1.4 1.4 µV
InEquivalent input
noise current 25°C 0.6 0.6 fA/Hz
Total harmonic
VO = ±2.3 V,
AV = 1 0.0011% 0.0011%
THD + N
Total harmonic
distortion pulse
duration
VO = ±2.3 V,
f = 20 kHz,
R = 10 k
AV = 10 25°C0.004% 0.004%
THD + N
distortion pulse
duration
f = 20 kHz,
RL = 10 kAV = 100
25 C
0.03% 0.03%
Gain-bandwidth
f = 10 kHz,
RL = 10 k
,
25°C
2.25
2.25
MHz
Gain-bandwidth
product
f = 10 kHz,
CL = 100 pF
RL = 10 k,
25°C 2.25 2.25 MHz
BOM
Maximum output-
VO(PP) = 4.6 V,
AV = 1,
25°C
0.54
0.54
MHz
BOM
Maximum output-
swing bandwidth
VO(PP) = 4.6 V,
RL = 10 k,
AV = 1,
CL = 100 pF 25°C0.54 0.54 MHz
AV = −1,
To 0.1%
1.5
1.5
ts
Settling time
AV = −1,
Step = −2.3 V to 2.3 V,
To 0.1%
25°C
1.5 1.5
s
tsSettling time
Step = −2.3 V to 2.3 V,
R
L
= 10 k,
To 0.01%
25°C
3.2
3.2
µs
s
RL = 10 k,
C
L
= 100 pF To 0.01% 3.2 3.2
φmPhase margin at
unity gain
RL = 10 k
,
CL = 100 pF
25°C52°52°
Gain margin
RL = 10 k,
CL = 100 pF
25°C 10 10 dB
Full range is 0°C to 70°C.
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
10 POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TLC2274C electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
TA
TLC2274C TLC2274AC
UNIT
PARAMETER
TEST CONDITIONS
T
A
MIN TYP MAX MIN TYP MAX
UNIT
Input offset voltage
25°C 300 2500 300 950
µV
IO
Input offset voltage
Full range 3000 1500 µ
V
αVIO Temperature coefficient
of input offset voltage 25°C
to 70°C2 2 µV/°C
Input offset voltage
long-term drift
(see Note 4) VDD± = ±2.5 V
,
VO = 0 V, VIC = 0 V,
RS = 50 25°C0.002 0.002 µV/mo
Input offset current
O
S
25°C 0.5 60 0.5 60
pA
IO
Input offset current
Full range 100 100
pA
Input bias current
25°C 1 60 1 60
pA
IB
Input bias current
Full range 100 100
pA
Common-mode input
RS = 50 ,
VIO 5 mV,
25°C0
to 4 0.3
to 4.2 0
to 4 0.3
to 4.2
V
ICR
Common-mode input
voltage
R
S
= 50
,
V
IO
5 mV,
Full range 0 to
3.5 0 to
3.5
V
IOH = −20 µA 25°C 4.99 4.99
IOH = −200 µA
25°C 4.85 4.93 4.85 4.93
V
High-level output voltage
I
OH
= −200
µ
A
Full range 4.85 4.85 V
High-level output voltage
IOH = −1 mA
25°C 4.25 4.65 4.25 4.65
V
I
OH
= −1 mA
Full range 4.25 4.25
VIC = 2.5 V, IOL = 50 µA 25°C 0.01 0.01
VIC = 2.5 V, IOL = 500 µA
25°C 0.09 0.15 0.09 0.15
V
Low-level output voltage
V
IC
= 2.5 V, I
OL
= 500
µ
A
Full range 0.15 0.15 V
Low-level output voltage
VIC = 2.5 V,
IOL = 5 mA
25°C 0.9 1.5 0.9 1.5
V
V
IC
= 2.5 V,
I
OL
= 5
m
A
Full range 1.5 1.5
Large-signal differential
VIC = 2.5 V,
RL = 10 k
25°C 15 35 15 35
A
Large-signal differential
voltage amplification
VIC = 2.5 V,
VO = 1 V to 4 V
RL = 10 k
Full range 15 15 V/mV
voltage amplification
V
O
= 1 V to 4 V
RL = 1 m25°C 175 175
V/mV
rid Differential input
resistance 25°C 1012 1012
riCommon-mode input
resistance 25°C 1012 1012
ciCommon-mode input
capacitance f = 10 kHz, N package 25°C 8 8 pF
zoClosed-loop output
impedance f = 1 MHz, AV = 10 25°C 140 140
Common-mode rejection
VIC = 0 V to 2.7 V,
25°C 70 75 70 75
dB
Common-mode rejection
ratio
VIC = 0 V to 2.7 V,
VO = 2.5 V, RS = 50 Full range 70 70
dB
Supply-voltage rejection
VDD = 4.4 V to 16 V,
25°C 80 95 80 95
dB
SVR
Supply-voltage rejection
ratio (VDD/VIO)
VDD = 4.4 V to 16 V,
VIC = VDD/2, No load Full range 80 80
dB
Supply current
VO = 2.5 V,
No load
25°C 4.4 6 4.4 6
mA
IDD Supply current VO = 2.5 V, No load Full range 6 6 mA
Full range is 0°C to 70°C.
Referenced to 0 V
NOTE 4: Typical values are based on the input of fset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
11
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TLC2274C operating characteristics at specified free-air temperature, VDD = 5 V
PARAMETER
TEST CONDITIONS
TA
TLC2274C TLC2274AC
UNIT
PARAMETER
TEST CONDITIONS
T
A
MIN TYP MAX MIN TYP MAX
UNIT
Slew rate at
VO = 0.5 V to 2.5 V,
25°C 2.3 3.6 2.3 3.6
SR Slew rate at
unity gain
VO = 0.5 V to 2.5 V,
RL = 10 k,
CL = 100 pF
Full
1.7
1.7
V/µs
SR
unity gain
R
L
= 10 k
,
C
L
= 100 pF
Full
range 1.7 1.7
V/µs
Vn
Equivalent input
f = 10 Hz 25°C 50 50
nV/Hz
Vn
Equivalent input
noise voltage f = 1 kHz 25°C 9 9 nV/Hz
VN(PP)
Peak-to-peak
equivalent input
f = 0.1 Hz to 1 Hz 25°C 1 1
V
VN(PP)
equivalent input
noise voltage f = 0.1 Hz to 10 Hz 25°C 1.4 1.4 µV
InEquivalent input
noise current 25°C 0.6 0.6 fA/Hz
Total harmonic
VO = 0.5 V to 2.5 V,
AV = 1 0.0013% 0.0013%
THD + N
Total harmonic
distortion plus
noise
VO = 0.5 V to 2.5 V,
f = 20 kHz,
R = 10 k
AV = 10 25°C0.004% 0.004%
THD + N
distortion plus
noise
f = 20 kHz,
RL = 10 kAV = 100
25 C
0.03% 0.03%
Gain-bandwidth
product f = 10 kHz,
CL = 100 pFRL = 10 k,25°C 2.18 2.18 MHz
BOM Maximum
output-swing
bandwidth
VO(PP) = 2 V,
RL = 10 k,AV = 1,
CL = 100 pF25°C 1 1 MHz
AV = −1,
To 0.1%
1.5
1.5
ts
Settling time
AV = −1,
Step = 0.5 V to 2.5 V,
To 0.1%
25°C
1.5 1.5
s
tsSettling time
Step = 0.5 V to 2.5 V,
R
L
= 10 k,
To 0.01%
25°C
2.6
2.6
µs
RL = 10 k,
C
L
= 100 pFTo 0.01% 2.6 2.6
φmPhase margin at
unity gain
RL = 10 k
,
CL = 100 pF
25°C 50°50°
Gain margin
RL = 10 k,
CL = 100 pF
25°C 10 10 dB
Full range is 0°C to 70°C.
Referenced to 0 V
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
12 POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TLC2274C electrical characteristics at specified free-air temperature, VDD± = ±5 V (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
TA
TLC2274C TLC2274AC
PARAMETER
TEST CONDITIONS
T
A
MIN TYP MAX MIN TYP MAX
Input offset voltage
25°C 300 2500 300 950
IO
Input offset voltage
Full range 3000 1500 µ
Temperature coefficient of
25
°
C
2
2
αVIO
Temperature coefficient of
input offset voltage
25 C
to 70°C
2
2
µ
°
Input offset voltage long-term
drift (see Note 4) VIC = 0 V,
R
S
= 50 VO = 0 V, 25°C0.002 0.002 µV/mo
Input offset current
RS = 50
25°C 0.5 60 0.5 60
IO
Input offset current
Full range 100 100
Input bias current
25°C 1 60 1 60
IB
Input bias current
Full range 100 100
Common-mode input
RS = 50
|VIO |≤ 5 mV
25°C−5
to 4 5.3
to 4.2 −5
to 4 5.3
to 4.2
ICR
Common-mode input
voltage
R
S
= 50
Ω, |
V
IO
| ≤
5 mV
Full range −5
to 3.5 −5
to 3.5
IO = −20 µA 25°C 4.99 4.99
Maximum positive peak output
IO = −200 µA
25°C 4.85 4.93 4.85 4.93
V
Maximum positive peak outpu
t
voltage
I
O
= −200
µ
A
Full range 4.85 4.85 V
voltage
IO = −1 mA
25°C 4.25 4.65 4.25 4.65
I
O
= −1 mA
Full range 4.25 4.25
VIC = 0 V, IO = 50 µA 25°C 4.99 4.99
Maximum negative peak
VIC = 0 V,
IO = 500 µA
25°C4.8
54.91 4.85 4.91
VOM Maximum negative peak
output voltage
V
IC
= 0 V,
I
O
= 500
µ
A
Full range 4.8
54.85 V
VIC = 0 V,
IO = −5 mA
25°C 3.5 4.1 3.5 4.1
V
IC
= 0 V,
I
O
= −5 mA
Full range 3.5 3.5
Large-signal differential
RL = 10 k
25°C 25 50 25 50
A
Large-signal differential
voltage amplification
V
O
= ±4 V
R
L
= 10 k
Full range 25 25 V/mV
voltage amplification
VO = 4 V
RL = 1 M25°C 300 300
rid Differential input resistance 25°C 1012 1012
riCommon-mode input
resistance 25°C 1012 1012
ciCommon-mode input
capacitance f = 10 kHz, N package 25°C 8 8 pF
zoClosed-loop output impedance f = 1 MHz, AV = 10 25°C 130 130
Common-mode rejection ratio
VIC = −5 V to 2.7 V,
25°C 75 80 75 80
Common-mode rejection ratio
VIC = −5 V to 2.7 V,
VO = 0 V, RS = 50 Full range 75 75
Supply-voltage rejection ratio
VDD± =
±
2.2 V to
±
8 V,
25°C 80 95 80 95
SVR
Supply-voltage rejection ratio
(VDD±/VIO)
VDD± = ±2.2 V to ±8 V,
VIC = 0 V, No load Full range 80 80
Supply current
VO = 0 V,
No load
25°C 4.8 6 4.8 6
DD
Supply current
V
O
= 0 V,
No load
Full range 6 6
Full range is 0°C to 70°C.
NOTE 4: Typical values are based on the input of fset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
13
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TLC2274C operating characteristics at specified free-air temperature, VDD± = ±5 V
PARAMETER
TEST CONDITIONS
TA
TLC2274C TLC2274AC
UNIT
PARAMETER
TEST CONDITIONS
T
A
MIN TYP MAX MIN TYP MAX
UNIT
Slew rate at unity
VO = ±2.3 V,
RL = 10 k,
25°C 2.3 3.6 2.3 3.6
SR Slew rate at unity
gain
VO = ±2.3 V,
CL = 100 pF
RL = 10 k,
Full
1.7
1.7
V/µs
SR
gain
CL = 100 pF
Full
range 1.7 1.7
V/µs
Vn
Equivalent input
f = 10 Hz 25°C 50 50
nV/Hz
Vn
Equivalent input
noise voltage f = 1 Hz 25°C 9 9 nV/Hz
VN(PP)
Peak-to-peak
equivalent input
f = 0.1 Hz to 1 Hz 25°C 1 1
V
VN(PP)
equivalent input
noise voltage f = 0.1 Hz to 10 Hz 25°C 1.4 1.4 µV
InEquivalent input
noise current 25°C 0.6 0.6 fA/Hz
Total harmonic
VO = ±2.3 V,
AV = 1 0.0011% 0.0011%
THD + N
Total harmonic
distortion plus
noise
VO = ±2.3 V,
f = 20 kHz,
R = 10 k
AV = 10 25°C0.004% 0.004%
THD + N
distortion plus
noise
f = 20 kHz,
RL = 10 kAV = 100
25 C
0.03% 0.03%
Gain-bandwidth
f = 10 kHz,
RL= 10 k
,
25°C
2.25
2.25
MHz
Gain-bandwidth
product
f = 10 kHz,
CL = 100 pF
RL= 10 k,
25°C 2.25 2.25 MHz
BOM
Maximum
output-swing
VO(PP) = 4.6 V,
AV = 1,
25°C
0.54
0.54
MHz
BOM
output-swing
bandwidth
VO(PP) = 4.6 V,
RL = 10 k,
AV = 1,
CL = 100 pF 25°C0.54 0.54 MHz
AV = −1,
To 0.1%
1.5
1.5
ts
Settling time
AV = −1,
Step = −2.3 V to 2.3 V,
To 0.1%
25°C
1.5 1.5
s
tsSettling time
Step = −2.3 V to 2.3 V,
R
L
= 10 k,
To 0.01%
25°C
3.2
3.2
µs
s
RL = 10 k,
C
L
= 100 pF To 0.01% 3.2 3.2
φmPhase margin at
unity gain
RL = 10 k
,
CL = 100 pF
25°C 52°52°
Gain margin
RL = 10 k,
CL = 100 pF
25°C 10 10 dB
Full range is 0°C to 70°C.
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
14 POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TLC2272I electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
T
TLC2272I TLC2272AI
UNIT
PARAMETER
TEST CONDITIONS
TA
MIN TYP MAX MIN TYP MAX
UNIT
Input offset voltage
25°C 300 2500 300 950
µV
IO
Input offset voltage
Full range 3000 1500 µ
V
Temperature coefficien
t
25°C
2
2
µV/
°
C
αVIO
Temperature coefficient
of input offset voltage
25 C
to 85°C
2
2
µ
V/
°
C
Input offset voltage
long-term drift
(see Note 4) VIC = 0 V,
V = 0 V,
VDD± = ±2.5 V
R = 50
25°C 0.002 0.002 µV/mo
VIC = 0 V,
VO = 0 V,
VDD = 2.5 V
RS = 50 25°C0.5 60 0.5 60
I
Input offset current −40°C to 85°C 150 150 pA
Input offset current
Full range 800 800
pA
25°C 1 60 1 60
IIB Input bias current −40°C to 85°C 150 150 pA
Input bias current
Full range 800 800
pA
25
°
C
0 to 4
−0.3
0 to 4
−0.3
Common-mode input
RS = 50
|VIO |≤ 5 mV
25
°
C
0 to 4
−0.3
to 4.2
0 to 4
−0.3
to 4.2
V
ICR
Common-mode input
voltage
R
S
= 50
Ω, |
V
IO | ≤
5 mV
Full range
0 to 0 to
V
voltage
Full range
0 to
3.5
0 to
3.5
IOH = −20 µA 25°C 4.99 4.99
High-level output
IOH = −200 µA
25°C 4.85 4.93 4.85 4.93
V
High-level output
voltage
I
OH
= −200
µ
A
Full range 4.85 4.85 V
voltage
IOH = −1 mA
25°C 4.25 4.65 4.25 4.65
V
I
OH
= −1 mA
Full range 4.25 4.25
VIC = 2.5 V, IOL = 50 µA 25°C 0.01 0.01
Low-level output
VIC = 2.5 V,
IOL = 500 µA
25°C 0.09 0.15 0.09 0.15
V
Low-level output
voltage
V
IC
= 2.5 V,
I
OL
= 500
µ
A
Full range 0.15 0.15 V
voltage
VIC = 2.5 V,
IOL = 5 mA
25°C 0.9 1.5 0.9 1.5
V
V
IC
= 2.5 V,
I
OL
= 5
m
A
Full range 1.5 1.5
Large-signal differential
V = 2.5 V,
RL = 10 k
25°C 15 35 15 35
A
Large-signal differentia
l
voltage amplification
VIC = 2.5 V,
VO = 1 V to 4 V
RL = 10 k
Full range 15 15 V/mV
voltage amplification
V
O
= 1 V to 4 V
RL = 1 m25°C 175 175
V/mV
rid Differential input
resistance 25°C 1012 1012
riCommon-mode input
resistance 25°C 1012 1012
ciCommon-mode input
capacitance f = 10 kHz, P package 25°C 8 8 pF
zoClosed-loop output
impedance f = 1 MHz, AV = 10 25°C 140 140
Common-mode V
IC
= 0 V to 2.7 V, 25°C 70 75 70 75
dB
Common-mode
rejection ratio
VIC = 0 V to 2.7 V,
VO = 2.5 V, RS = 50 Full range 70 70
dB
Supply-voltage
rejection ratio
V
DD
= 4.4 V to 16 V, 25°C 80 95 80 95
dB
SVR
rejection ratio
(VDD/VIO)
VDD = 4.4 V to 16 V,
VIC = VDD/2, No load Full range 80 80
dB
Supply current
VO = 2.5 V,
No load
25°C 2.2 3 2.2 3
mA
IDD Supply current VO = 2.5 V, No load Full range 3 3 mA
Full range is − 40°C to 125°C.
Referenced to 0 V
NOTE 4: Typical values are based on the input of fset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
15
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TLC2272I operating characteristics at specified free-air temperature, VDD = 5 V
PARAMETER
TEST CONDITIONS
TA
TLC2272I TLC2272AI
UNIT
PARAMETER
TEST CONDITIONS
TA
MIN TYP MAX MIN TYP MAX
UNIT
Slew rate at
VO = 0.5 V to 2.5 V,
25°C2.3 3.6 2.3 3.6
SR Slew rate at
unity gain
VO = 0.5 V to 2.5 V
,
RL = 10 k,
CL = 100 pF
Full
1.7
1.7
V/µs
SR
unity gain
RL = 10 k,
CL = 100 pF
Full
range 1.7 1.7
V/µs
Vn
Equivalent input
f = 10 Hz 25°C 50 50
nVHz
Vn
Equivalent input
noise voltage f = 1 kHz 25°C 9 9
nVHz
VNPP
Peak-to-peak
equivalent input
f = 0.1 Hz to 1 Hz 25°C 1 1
V
VNPP
equivalent input
noise voltage f = 0.1 Hz to 10 Hz 25°C 1.4 1.4 µV
InEquivalent input
noise current 25°C 0.6 0.6 fAHz
Total harmonic
VO = 0.5 V to 2.5 V,
AV = 1 0.0013% 0.0013%
THD + N
Total harmonic
distortion plus
noise
VO = 0.5 V to 2.5 V,
f = 20 kHz,
R = 10 k
AV = 10 25°C0.004% 0.004%
THD + N
distortion plus
noise
f = 20 kHz,
RL = 10 kAV = 100
25 C
0.03% 0.03%
Gain-bandwidth
f = 10 kHz,
RL = 10 k
,
25°C
2.18
2.18
MHz
Gain-bandwidth
product
f = 10 kHz,
C
L
= 100 pF
RL = 10 k,
25°C 2.18 2.18 MHz
BOM
Maximum output-
VO(PP) = 2 V,
AV = 1,
25°C
1
1
MHz
BOM
Maximum output-
swing bandwidth
VO(PP) = 2 V,
RL = 10 k,
AV = 1,
CL = 100 pF25°C1 1 MHz
AV = −1,
To 0.1%
1.5
1.5
ts
Settling time
AV = −1,
Step = 0.5 V to 2.5 V,
To 0.1%
25°C
1.5 1.5
s
tsSettling time
Step = 0.5 V to 2.5 V,
R
L
= 10 k,
To 0.01%
25°C
2.6
2.6
µs
s
RL = 10 k,
C
L
= 100 pFTo 0.01% 2.6 2.6
φmPhase margin at
unity gain
RL = 10 k
,
CL = 100 pF
25°C50°50°
Gain margin
RL = 10 k,
CL = 100 pF
25°C 10 10 dB
Full range is − 40°C to 125°C.
Referenced to 0 V
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
16 POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TLC2272I electrical characteristics at specified free-air temperature, VDD± = ±5 V (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
T
TLC2272I TLC2272AI
UNIT
PARAMETER
TEST CONDITIONS
TA
MIN TYP MAX MIN TYP MAX
UNIT
Input offset voltage
25°C 300 2500 300 950
µV
IO
Input offset voltage
Full range 3000 1500 µ
V
αVIO
Temperature
coefficient of input
offset voltage 25°C to 85°C 2 2 µV/°C
Input offset voltage
long-term drift
(see Note 4) VIC = 0 V,
RS = 50
VO = 0 V, 25°C0.002 0.002 µV/mo
RS = 50
25°C 0.5 60 0.5 60
I
Input offset current −40°C to 85°C 150 150 pA
Input offset current
Full range 800 800
pA
25°C 1 60 1 60
I
Input bias current −40°C to 85°C 150 150 pA
Input bias current
Full range 800 800
pA
Common-mode
RS = 50
|VIO |≤5 mV
25°C−5 to
4−5.3
to 4.2 −5 to
45.3
to 4.2
V
ICR
Common-mode
input voltage
R
S
= 50
Ω, |
V
IO | ≤
5 mV
Full range −5 to
3.5 −5 to
3.5
V
IO = −20 µA 25°C 4.99 4.99
Maximum positive
IO = −200 µA
25°C 4.85 4.93 4.85 4.93
VOM+ Maximum positive
peak output voltage
I
O
= −200
µ
A
Full range 4.85 4.85 V
peak output voltage
IO = −1 mA
25°C 4.25 4.65 4.25 4.65
V
I
O
= −1 mA
Full range 4.25 4.25
VIC = 0 V, IO = 50 µA 25°C 4.99 4.99
Maximum negative
VIC = 0 V,
IO = 500 µA
25°C 4.85 4.91 4.85 4.91
V
Maximum negative
peak output voltage
V
IC
= 0 V,
I
O
= 500
µ
A
Full range 4.85 4.85 V
peak output voltage
VIC = 0 V,
IO = 5 mA
25°C 3.5 4.1 3.5 4.1
V
V
IC
= 0 V,
I
O
= 5
m
A
Full range 3.5 3.5
Large-signal
RL = 10 k
25°C 25 50 25 50
A
Large-signal
differential voltage
amplification
V
O
= ±4 V
R
L
= 10 k
Full range 25 25 V/mV
differential voltage
amplification
VO = ±4 V
RL = 1 m25°C 300 300
V/mV
rid Differential input
resistance 25°C 1012 1012
riCommon-mode
input resistance 25°C 1012 1012
ciCommon-mode
input capacitance f = 10 kHz, P package 25°C 8 8 pF
zoClosed-loop output
impedance f = 1 MHz, AV = 10 25°C 130 130
Common-mode V
IC
= −5 V to 2.7 V, 25°C 75 80 75 80
dB
Common-mode
rejection ratio
VIC = −5 V to 2.7 V,
VO = 0 V, RS = 50 Full range 75 75
dB
Supply-voltage
rejection ratio
VDD = 4.4 V to 16 V,
25°C 80 95 80 95
dB
SVR
rejection ratio
(VDD±/VIO)
VDD = 4.4 V to 16 V,
VIC = VDD/2, No load Full range 80 80
dB
Supply current
VO = 0 V,
No load
25°C 2.4 3 2.4 3
mA
IDD Supply current VO = 0 V, No load Full range 3 3 mA
Full range is − 40°C to 125°C.
NOTE 4: Typical values are based on the input of fset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
17
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TLC2272I operating characteristics at specified free-air temperature, VDD± = ±5 V
PARAMETER
TEST CONDITIONS
TA
TLC2272I TLC2272AI
UNIT
PARAMETER
TEST CONDITIONS
TA
MIN TYP MAX MIN TYP MAX
UNIT
Slew rate at
VO = ±2.3 V,
RL = 10 k,
25°C 2.3 3.6 2.3 3.6
SR
Slew rate at
unity gain
V
O
=
±
2.3 V,
CL = 100 pF
R
L
= 10 k
,
Full
1.7
1.7
V/µs
SR
unity gain
CL = 100 pF
Full
range 1.7 1.7
V/µs
Vn
Equivalent input
f = 10 Hz 25°C 50 50
nVHz
Vn
Equivalent input
noise voltage f = 1 kHz 25°C 9 9
nVHz
VNPP
Peak-to-peak
equivalent input
f = 0.1 Hz to 1 Hz 25°C 1 1
V
VNPP
equivalent input
noise voltage f = 0.1 Hz to 10 Hz 25°C 1.4 1.4 µV
InEquivalent input
noise current 25°C 0.6 0.6 fAHz
Total harmonic
VO = ±2.3 V
AV = 1 0.0011% 0.0011%
THD + N
Total harmonic
distortion plus
noise
VO = ±2.3 V
R
L
= 10 kΩ,
f = 20 kHz
AV = 10 25°C0.004% 0.004%
THD + N
distortion plus
noise
RL = 10 kΩ,
f = 20 kHz AV = 100
25 C
0.03% 0.03%
Gain-bandwidth
f = 10 kHz,
RL = 10 k
,
25°C
2.25
2.25
MHz
Gain-bandwidth
product
f = 10 kHz,
CL = 100 pF
RL = 10 k,
25°C 2.25 2.25 MHz
BOM
Maximum
output-swing
VO(PP) = 4.6 V,
AV = 1,
25°C
0.54
0.54
MHz
BOM
output-swing
bandwidth
VO(PP) = 4.6 V,
RL = 10 k,
AV = 1,
CL = 100 pF 25°C0.54 0.54 MHz
AV = −1,
To 0.1%
1.5
1.5
ts
Settling time
AV = −1,
Step = −2.3 V to 2.3 V,
To 0.1%
25°C
1.5 1.5
s
tsSettling time
Step = −2.3 V to 2.3 V,
R
L
= 10 k,
To 0.01%
25°C
3.2
3.2
µs
s
RL = 10 k,
C
L
= 100 pF To 0.01% 3.2 3.2
φmPhase margin at
unity gain
RL = 10 k
,
CL = 100 pF
25°C52°52°
Gain margin
RL = 10 k,
CL = 100 pF
25°C 10 10 dB
Full range is −40°C to 125°C.
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
18 POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TLC2274I electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
TA
TLC2274I TLC2274AI
UNIT
PARAMETER
TEST CONDITIONS
TA
MIN TYP MAX MIN TYP MAX
UNIT
Input offset voltage
25°C 300 2500 300 950
µV
IO
Input offset voltage
Full range 3000 1500 µ
V
Temperature coefficient of
25
°
C to 85
°
C
2
2
µV/
°
C
αVIO
Temperature coefficient of
input offset voltage
25
°
C to 85
°
C
2
2
µ
V/
°
C
Input offset voltage
long-term drift (see Note 4)
VDD± = ±2.5 V,
VIC = 0 V,
25°C 0.002 0.002 µV/mo
V
DD±
=
±
2.5 V,
V
O
= 0 V,
V
IC
= 0 V,
R
S
= 50 25°C0.5 60 0.5 60
IIO Input offset current
VO = 0 V,
RS = 50
−40°C to 85°C 150 150 pA
Input offset current
Full range 800 800
pA
25°C 1 60 1 60
IIB Input bias current −40°C to 85°C 150 150 pA
Input bias current
Full range 800 800
pA
Common-mode input
RS = 50
|VIO |≤ 5 mV
25°C0 to
4−0.3
to 4.2 0 to
4−0.3
to 4.2
V
ICR
Common-mode input
voltage
R
S
= 50
Ω, |
V
IO | ≤
5 mV
Full range 0 to
3.5 0 to
3.5
V
IOH = −20 µA 25°C 4.99 4.99
IOH = −200 µA
25°C 4.85 4.93 4.85 4.93
VOH High-level output voltage
I
OH
= −200
µ
A
Full range 4.85 4.85 V
High-level output voltage
IOH = −1 mA
25°C 4.25 4.65 4.25 4.65
V
I
OH
= −1 mA
Full range 4.25 4.25
VIC = 2.5 V, IOL = 50 µA 25°C 0.01 0.01
VIC = 2.5 V,
IOL = 500 µA
25°C 0.09 0.15 0.09 0.15
VOL Low-level output voltage
V
IC
= 2.5 V,
I
OL
= 500
µ
A
Full range 0.15 0.15 V
Low-level output voltage
VIC = 2.5 V,
IOL = 5 mA
25°C 0.9 1.5 0.9 1.5
V
V
IC
= 2.5 V,
I
OL
= 5
m
A
Full range 1.5 1.5
Large-signal differential
V = 2.5 V,
RL = 10 k
25°C 15 35 15 35
A
Large-signal differential
voltage amplification
VIC = 2.5 V,
VO = 1 V to 4 V
RL = 10 k
Full range 15 15 V/mV
voltage amplification
V
O
= 1 V to 4 V
RL = 1 M25°C 175 175
V/mV
rid Differential input resistance 25°C 1012 1012
riCommon-mode input
resistance 25°C 1012 1012
ciCommon-mode input
capacitance f = 10 kHz, N package 25°C 8 8 pF
zoClosed-loop output
impedance f = 1 MHz, AV = 10 25°C 140 140
Common-mode rejection V
IC
= 0 V to 2.7 V, 25°C 70 75 70 75
dB
Common-mode rejection
ratio
VIC = 0 V to 2.7 V,
VO = 2.5 V, RS = 50 Full range 70 70
dB
Supply-voltage rejection V
DD
= 4.4 V to 16 V, 25°C 80 95 80 95
dB
SVR
Supply-voltage rejection
ratio (VDD /VIO)
VDD = 4.4 V to 16 V,
VIC = VDD/2, No load Full range 80 80
dB
Supply current
VO = 2.5 V,
No load
25°C 4.4 6 4.4 6
mA
DD
Supply current
V
O
= 2.5 V,
No load
Full range 6 6
mA
Full range is − 40°C to 125°C.
Referenced to 0 V
NOTE 4: Typical values are based on the input of fset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
19
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TLC2274I operating characteristics at specified free-air temperature, VDD = 5 V
PARAMETER
TEST CONDITIONS
TA
TLC2274I TLC2274AI
UNIT
PARAMETER
TEST CONDITIONS
T
A
MIN TYP MAX MIN TYP MAX
UNIT
Slew rate at unity
VO = 0.5 V to 2.5 V,
25°C2.3 3.6 2.3 3.6
SR Slew rate at unity
gain
VO = 0.5 V to 2.5 V,
RL = 10 k, CL = 100 pF
Full
1.7
1.7
V/µs
SR
gain
RL = 10 k, CL = 100 pF
Full
range 1.7 1.7
V/µs
Vn
Equivalent input
f = 10 Hz 25°C 50 50
nV/Hz
Vn
Equivalent input
noise voltage f = 1 kHz 25°C 9 9 nV/Hz
VN(PP)
Peak-to-peak
equivalent input
f = 0.1 Hz to 1 Hz 25°C 1 1
V
VN(PP)
equivalent input
noise voltage f = 0.1 Hz to 10 Hz 25°C 1.4 1.4 µV
InEquivalent input
noise current 25°C 0.6 0.6 fA/Hz
Total harmonic
VO = 0.5 V to 2.5 V,
AV = 1 0.0013% 0.0013%
THD + N Total harmonic
distortion plus noise
VO = 0.5 V to 2.5 V,
f = 20 kHz,
R = 10 k
AV = 10 25°C0.004% 0.004%
THD + N
distortion plus noise
f = 20 kHz,
RL = 10 kAV = 100
25 C
0.03% 0.03%
Gain-bandwidth
f = 10 kHz,
RL = 10 k
,
25°C
2.18
2.18
MHz
Gain-bandwidth
product
f = 10 kHz,
C
L
= 100 pF
RL = 10 k,
25°C 2.18 2.18 MHz
BOM
Maximum
output-swing
VO(PP) = 2 V,
AV = 1,
25°C
1
1
MHz
BOM
output-swing
bandwidth
VO(PP) = 2 V,
RL = 10 k,
AV = 1,
CL = 100 pF25°C1 1 MHz
AV = −1,
To 0.1%
1.5
1.5
ts
Settling time
AV = −1,
Step = 0.5 V to 2.5 V,
To 0.1%
25°C
1.5 1.5
s
tsSettling time
Step = 0.5 V to 2.5 V,
R
L
= 10 k,
To 0.01%
25°C
2.6
2.6
µs
s
RL = 10 k,
C
L
= 100 pFTo 0.01% 2.6 2.6
φmPhase margin at
unity gain
RL = 10 k
,
CL = 100 pF
25°C 50°50°
Gain margin
RL = 10 k,
CL = 100 pF
25°C 10 10 dB
Full range is − 40°C to 125°C.
Referenced to 0 V
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
20 POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TLC2274I electrical characteristics at specified free-air temperature, VDD± = ±5 V (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
TA
TLC2274I TLC2274AI
UNIT
PARAMETER
TEST CONDITIONS
TA
MIN TYP MAX MIN TYP MAX
UNIT
Input offset voltage
25°C 300 2500 300 950
µV
IO
Input offset voltage
Full range 3000 1500 µ
V
Temperature coefficient of
25
°
C to 85
°
C
2
2
µV/
°
C
αVIO
Temperature coefficient of
input offset voltage
25
°
C to 85
°
C
2
2
µ
V/
°
C
Input offset voltage
long-term drift (see Note 4)
VIC = 0 V,
VO = 0 V,
25°C 0.002 0.002 µV/mo
V
IC
= 0 V,
R
S
= 50
V
O
= 0 V,
25°C 0.5 60 0.5 60
IIO Input offset current
RS = 50
−40°C to 85°C 150 150 pA
Input offset current
Full range 800 800
pA
25°C 1 60 1 60
IIB Input bias current −40°C to 85°C 150 150 pA
Input bias current
Full range 800 800
pA
Common-mode input
RS = 50
VIO |≤5 mV
25°C−5 to
4−5.3
to 4.2 −5 to
4−5.3
to 4.2
V
ICR
Common-mode input
voltage
R
S
= 50
Ω,
V
IO | ≤
5 mV
Full range −5 to
3.5 −5 to
3.5
V
IO = −20 µA 25°C 4.99 4.99
Maximum positive peak
IO = −200 µA
25°C 4.85 4.93 4.85 4.93
VOM+ Maximum positive peak
output voltage
I
O
= −200
µ
A
Full range 4.85 4.85 V
output voltage
IO = −1 mA
25°C 4.25 4.65 4.25 4.65
V
I
O
= −1 mA
Full range 4.25 4.25
VIC = 0 V, IO = 50 µA 25°C 4.99 4.99
Maximum negative peak
VIC = 0 V,
IO = 500 µA
25°C 4.85 4.91 4.85 4.91
VOM Maximum negative peak
output voltage
V
IC
= 0 V,
I
O
= 500
µ
A
Full range 4.85 4.85 V
output voltage
VIC = 0 V,
IO = 5 mA
25°C 3.5 4.1 3.5 4.1
V
V
IC
= 0 V,
I
O
= 5
m
A
Full range 3.5 3.5
Large-signal differential
RL = 10 k
25°C 25 50 25 50
AVD Large-signal differential
voltage amplification
VO = ±4 V
R
L
= 10 k
Full range 25 25 V/mV
voltage amplification
VO = 4 V
RL = 1 M25°C 300 300
V/mV
rid Differential input resistance 25°C 1012 1012
riCommon-mode input
resistance 25°C 1012 1012
ciCommon-mode input
capacitance f = 10 kHz, N package 25°C 8 8 pF
zoClosed-loop output
impedance f = 1 MHz, AV = 10 25°C 130 130
Common-mode rejection V
IC
= −5 V to 2.7 V, 25°C 75 80 75 80
dB
Common-mode rejection
ratio
VIC = −5 V to 2.7 V,
VO = 0 V, RS = 50 Full range 75 75
dB
Supply-voltage rejection V
DD
± = ±2.2 V to ±8 V, 25°C 80 95 80 95
dB
SVR
Supply-voltage rejection
ratio (VDD±/VIO)
VDD± = ±2.2 V to ±8 V,
VIC = 0 V, No load Full range 80 80
dB
Supply current
VO = 0 V,
No load
25°C 4.8 6 4.8 6
mA
DD
Supply current
V
O
= 0 V,
No load
Full range 6 6
mA
Full range is − 40°C to 125°C.
NOTE 4: Typical values are based on the input of fset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
21
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TLC2274I operating characteristics at specified free-air temperature, VDD± = ±5 V
PARAMETER
TEST CONDITIONS
TA
TLC2274I TLC2274AI
UNIT
PARAMETER
TEST CONDITIONS
T
A
MIN TYP MAX MIN TYP MAX
UNIT
Slew rate at unity
VO = ±2.3 V,
RL = 10 k,
25°C 2.3 3.6 2.3 3.6
SR Slew rate at unity
gain
VO = ±2.3 V,
CL = 100 pF
RL = 10 k,
Full
1.7
1.7
V/µs
SR
gain
CL = 100 pF
Full
range 1.7 1.7
V/µs
Vn
Equivalent input
f = 10 Hz 25°C 50 50
nV/Hz
Vn
Equivalent input
noise voltage f = 1 kHz 25°C 9 9 nV/Hz
VN(PP)
Peak-to-peak
equivalent input
f = 0.1 Hz to 1 Hz 25°C 1 1
V
VN(PP)
equivalent input
noise voltage f = 0.1 Hz to 10 Hz 25°C 1.4 1.4 µV
InEquivalent input
noise current 25°C 0.6 0.6 fA/Hz
Total harmonic
VO = ±2.3 V,
AV = 1 0.0011% 0.0011%
THD + N
Total harmonic
distortion plus
noise
VO = ±2.3 V,
R
L
= 10 kΩ,
f = 20 kHz
AV = 10 25°C0.004% 0.004%
THD + N
distortion plus
noise
RL = 10 kΩ,
f = 20 kHz AV = 100
25 C
0.03% 0.03%
Gain-bandwidth
f = 10 kHz,
RL = 10 k
,
25°C
2.25
2.25
MHz
Gain-bandwidth
product
f = 10 kHz,
CL = 100 pF
RL = 10 k,
25°C 2.25 2.25 MHz
BOM
Maximum output-
VO(PP) = 4.6 V,
AV = 1,
25°C
0.54
0.54
MHz
BOM
Maximum output-
swing bandwidth
VO(PP) = 4.6 V,
R
L
= 10 k,
AV = 1,
C
L
= 100 pF 25°C0.54 0.54 MHz
AV = −1,
To 0.1%
1.5
1.5
ts
Settling time
AV = −1,
Step = −2.3 V to 2.3 V,
To 0.1%
25°C
1.5 1.5
s
tsSettling time
Step = −2.3 V to 2.3 V,
R
L
= 10 k,
To 0.01%
25°C
3.2
3.2
µs
s
RL = 10 k,
C
L
= 100 pF To 0.01% 3.2 3.2
φmPhase margin at
unity gain
RL = 10 k
,
CL = 100 pF
25°C 52°52°
Gain margin
RL = 10 k,
CL = 100 pF
25°C 10 10 dB
Full range is −40°C to 125°C.
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
22 POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TLC2272Q and TLC2272M electrical characteristics at specified free-air temperature, VDD = 5 V
(unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
TLC2272Q,
TLC2272M TLC2272AQ,
TLC2272AM
UNIT
PARAMETER
TEST CONDITIONS
TA
MIN TYP MAX MIN TYP MAX
UNIT
Input offset voltage
25°C 300 2500 300 950
µV
IO
Input offset voltage
Full range 3000 1500 µ
V
Temperature coefficient
25
°
C
2
2
µV/°C
αVIO
Temperature coefficient
of input offset voltage
25 C
to 125°C
2
2
µ
V/
°
C
Input offset voltage long-
term drift (see Note 4) VIC = 0 V,
V
O
= 0 V, VDD± = ±2.5 V
,
R
S
= 50 25°C 0.002 0.002 µV/mo
Input offset current
VO = 0 V,
RS = 50
25°C 0.5 60 0.5 60
pA
IO
Input offset current
Full range 800 800
pA
Input bias current
25°C 1 60 1 60
pA
IB
Input bias current
Full range 800 800
pA
Common-mode input
RS = 50
|VIO |≤ 5 mV
25°C0
to 4 0.3
to 4.2 0
to 4 0.3
to 4.2
V
ICR
Common-mode input
voltage
R
S
= 50
Ω, |
V
IO
| ≤
5 mV
Full range 0
to 3.5 0
to 3.5
V
IOH = −20 µA 25°C 4.99 4.99
High-level output
IOH = −200 µA
25°C 4.85 4.93 4.85 4.93
V
High-level output
voltage
I
OH
= −200
µ
A
Full range 4.85 4.85 V
voltage
IOH = −1 mA
25°C 4.25 4.65 4.25 4.65
V
I
OH
= −1 mA
Full range 4.25 4.25
VIC = 2.5 V, IOL = 50 µA 25°C 0.01 0.01
VIC = 2.5 V,
IOL = 500 µA
25°C 0.09 0.15 0.09 0.15
V
Low-level output voltage
V
IC
= 2.5 V,
I
OL
= 500
µ
A
Full range 0.15 0.15 V
Low-level output voltage
VIC = 2.5 V,
IOL = 5 mA
25°C 0.9 1.5 0.9 1.5
V
V
IC
= 2.5 V,
I
OL
= 5
m
A
Full range 1.5 1.5
Large-signal
VIC = 2.5 V,
RL = 10 k
25°C 10 35 10 35
A
Large-signal
differential voltage VIC = 2.5 V,
VO = 1 V to 4 V
RL = 10 k
Full range 10 10 V/mV
differential voltage
amplification
V
O
= 1 V to 4 V
RL = 1 m25°C 175 175
V/mV
rid Differential input
resistance 25°C 1012 1012
riCommon-mode input
resistance 25°C 1012 1012
ciCommon-mode input
capacitance f = 10 kHz, P package 25°C 8 8 pF
zoClosed-loop output
impedance f = 1 MHz, AV = 10 25°C 140 140
Common-mode rejection
VIC = 0 V to 2.7 V,
25°C 70 75 70 75
dB
Common-mode rejection
ratio
VIC = 0 V to 2.7 V,
VO = 2.5 V, RS = 50 Full range 70 70
dB
Supply-voltage rejection
VDD = 4.4 V to 16 V,
25°C 80 95 80 95
dB
SVR
Supply-voltage rejection
ratio (VDD/VIO)
VDD = 4.4 V to 16 V,
VIC = VDD/2, No load Full range 80 80
dB
Supply current
VO = 2.5 V,
No load
25°C 2.2 3 2.2 3
mA
IDD Supply current VO = 2.5 V, No load Full range 3 3 mA
Full range is −40°C to 125°C for Q level part, −55°C to 125°C for M level part.
Referenced to 2.5 V
NOTE 4: Typical values are based on the input of fset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
23
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TLC2272Q and TLC2272M operating characteristics at specified free-air temperature, VDD = 5 V
PARAMETER
TEST CONDITIONS
TA
TLC2272Q,
TLC2272M TLC2272AQ,
TLC2272AM
UNIT
PARAMETER
TEST CONDITIONS
TA
MIN TYP MAX MIN TYP MAX
UNIT
Slew rate at
VO = 1.25 V to 2.75 V,
25°C 2.3 3.6 2.3 3.6
SR Slew rate at
unity gain
VO = 1.25 V to 2.75 V,
RL = 10 k‡, CL = 100 pF
Full
1.7
1.7
V/µs
SR
unity gain
RL = 10 k‡, CL = 100 pF
Full
range 1.7 1.7
V/µs
Vn
Equivalent input
f = 10 Hz 25°C 50 50
nV/Hz
Vn
Equivalent input
noise voltage f = 1 kHz 25°C 9 9
nV/Hz
VNPP
Peak-to-peak
equivalent input
f = 0.1 Hz to 1 Hz 25°C 1 1
V
VNPP
equivalent input
noise voltage f = 0.1 Hz to 10 Hz 25°C 1.4 1.4 µV
InEquivalent input
noise current 25°C 0.6 0.6 fA/Hz
Total harmonic
VO = 0.5 V to 2.5 V,
AV = 1 0.0013% 0.0013%
THD + N
Total harmonic
distortion plus
noise
VO = 0.5 V to 2.5 V,
f = 20 kHz,
R = 10 k ,
AV = 10 25°C0.004% 0.004%
THD + N
distortion plus
noise
f = 20 kHz,
RL = 10 k,AV = 100
25 C
0.03% 0.03%
Gain-bandwidth
f = 10 kHz,
RL = 10 k
,
25°C
2.18
2.18
MHz
Gain-bandwidth
product
f = 10 kHz,
C
L
= 100 pF
RL = 10 k,
25°C 2.18 2.18 MHz
BOM
Maximum output-
VO(PP) = 2 V,
AV = 1,
25°C
1
1
MHz
BOM
Maximum output-
swing bandwidth
VO(PP) = 2 V,
RL = 10 k,
AV = 1,
CL = 100 pF25°C1 1 MHz
AV = −1,
To 0.1%
1.5
1.5
ts
Settling time
AV = −1,
Step = 0.5 V to 2.5 V,
To 0.1%
25°C
1.5 1.5
s
tsSettling time
Step = 0.5 V to 2.5 V,
R
L
= 10 k,
To 0.01%
25°C
2.6
2.6
µs
s
RL = 10 k,
C
L
= 100 pFTo 0.01% 2.6 2.6
φmPhase margin at
unity gain
RL = 10 k
,
CL = 100 pF
25°C50°50°
Gain margin
RL = 10 k,
CL = 100 pF
25°C 10 10 dB
Full range is −40°C to 125°C for Q level part, −55°C to 125°C for M level part.
Referenced to 2.5 V
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
24 POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TLC2272Q and TLC2272M electrical characteristics at specified free-air temperature, VDD± = ±5 V
(unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
TLC2272Q,
TLC2272M TLC2272AQ,
TLC2272AM
UNIT
PARAMETER
TEST CONDITIONS
TA
MIN TYP MAX MIN TYP MAX
UNIT
Input offset voltage
25°C 300 2500 300 950
µV
IO
Input offset voltage
Full range 3000 1500 µ
V
Temperature coefficient of
25
°
C
2
2
µV/°C
αVIO
Temperature coefficient of
input offset voltage
25 C
to 125°C
2
2
µ
V/
°
C
Input offset voltage
long-term drift
(see Note 4) VIC = 0 V,
RS = 50 VO = 0 V, 25°C0.002 0.002 µV/mo
Input offset current
S
25°C 0.5 60 0.5 60
pA
IO
Input offset current
Full range 800 800
pA
Input bias current
25°C 1 60 1 60
pA
IB
Input bias current
Full range 800 800
pA
25 C
−5
5.3
−5
5.3
Common-mode input
25
°
C
−5
to 4
5.3
to 4.2
−5
to 4
5.3
to 4.2
Common-mode input
RS = 50
|VIO |≤5 mV
25 C
to 4 to 4.2 to 4 to 4.2
V
ICR
Common-mode input
voltage
R
S
= 50
Ω, |
V
IO
| ≤
5 mV
Full range
−5
−5
V
voltage
RS = 50 ,
|VIO |5 mV
Full range
−5
to 3.5
−5
to 3.5
V
Full range
to 3.5 to 3.5
IO = −20 µA 25°C 4.99 4.99
Maximum positive peak
IO = −200 µA
25°C 4.85 4.93 4.85 4.93
V
Maximum positive peak
output voltage
I
O
= −200
µ
A
Full range 4.85 4.85 V
output voltage
IO = −1 mA
25°C 4.25 4.65 4.25 4.65
V
I
O
= −1 mA
Full range 4.25 4.25
VIC = 0 V, IO = 50 µA 25°C 4.99 4.99
Maximum negative peak
VIC = 0 V,
IO = 500 µA
25°C 4.85 4.91 4.85 4.91
V
Maximum negative peak
output voltage
V
IC
= 0 V,
I
O
= 500
µ
A
Full range 4.85 4.85 V
output voltage
VIC = 0 V,
IO = 5 mA
25°C 3.5 4.1 3.5 4.1
V
V
IC
= 0 V,
I
O
= 5
m
A
Full range 3.5 3.5
Large-signal differential
RL = 10 k
25°C 20 50 20 50
A
Large-signal differential
voltage amplification
V
O
= ±4 V
R
L
= 10 k
Full range 20 20 V/mV
voltage amplification
VO = ±4 V
RL = 1 m25°C 300 300
V/mV
rid Differential input resistance 25°C 1012 1012
riCommon-mode input
resistance 25°C 1012 1012
ciCommon-mode input
capacitance f = 10 kHz, P package 25°C 8 8 pF
zoClosed-loop output
impedance f = 1 MHz, AV = 10 25°C 130 130
Common-mode rejection
VIC = −5 V to 2.7 V,
25°C 75 80 75 80
dB
Common-mode rejection
ratio
VIC = −5 V to 2.7 V,
VO = 0 V, RS = 50 Full range 75 75
dB
Supply-voltage rejection
VDD =
±
2.2 V to
±
8 V,
25°C 80 95 80 95
dB
SVR
Supply-voltage rejection
ratio (VDD±/VIO)
VDD = ±2.2 V to ±8 V,
VIC = 0 V, No load Full range 80 80
dB
Supply current
VO = 2.5 V,
No load
25°C 2.4 3 2.4 3
mA
IDD Supply current VO = 2.5 V, No load Full range 3 3 mA
Full range is −40°C to 125°C for Q level part, −55°C to 125°C for M level part.
NOTE 4: Typical values are based on the input of fset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
25
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TLC2272Q and TLC2272M operating characteristics at specified free-air temperature,
VDD± = ±5 V
PARAMETER
TEST CONDITIONS
TA
TLC2272Q,
TLC2272M TLC2272AQ,
TLC2272AM
UNIT
PARAMETER
TEST CONDITIONS
TA
MIN TYP MAX MIN TYP MAX
UNIT
Slew rate at
VO = ±1 V, RL = 10 k,
25°C 2.3 3.6 2.3 3.6
SR Slew rate at
unity gain
VO = ±1 V, RL = 10 k,
CL = 100 pF
Full
1.7
1.7
V/µs
SR
unity gain
CL = 100 pF
Full
range 1.7 1.7
V/µs
Vn
Equivalent input
f = 10 Hz 25°C 50 50
nV/Hz
Vn
Equivalent input
noise voltage f = 1 kHz 25°C 9 9
nV/Hz
VNPP
Peak-to-peak
equivalent input
f = 0.1 Hz to 1 Hz 25°C 1 1
V
VNPP
equivalent input
noise voltage f = 0.1 Hz to 10 Hz 25°C 1.4 1.4 µV
InEquivalent input
noise current 25°C 0.6 0.6 fA/Hz
Total harmonic
VO = ±2.3 V
AV = 1 0.0011% 0.0011%
THD + N
Total harmonic
distortion plus
noise
VO = ±2.3 V
R
L
= 10 kΩ,
f = 20 kHz
AV = 10 25°C0.004% 0.004%
THD + N
distortion plus
noise
RL = 10 kΩ,
f = 20 kHz AV = 100
25 C
0.03% 0.03%
Gain-bandwidth
f = 10 kHz,
RL = 10 k
,
25°C
2.25
2.25
MHz
Gain-bandwidth
product
f = 10 kHz,
CL = 100 pF
RL = 10 k,
25°C 2.25 2.25 MHz
BOM
Maximum
output-swing
VO(PP) = 4.6 V,
AV = 1,
25°C
0.54
0.54
MHz
BOM
output-swing
bandwidth
VO(PP) = 4.6 V,
RL = 10 k,
AV = 1,
CL = 100 pF 25°C 0.54 0.54 MHz
AV = −1,
To 0.1%
1.5
1.5
ts
Settling time
AV = −1,
Step = −2.3 V to 2.3 V,
To 0.1%
25°C
1.5 1.5
s
tsSettling time
Step = −2.3 V to 2.3 V,
R
L
= 10 k,
To 0.01%
25°C
3.2
3.2
µs
s
RL = 10 k,
C
L
= 100 pF To 0.01% 3.2 3.2
φmPhase margin at
unity gain
RL = 10 k
,
CL = 100 pF
25°C52°52°
Gain margin
RL = 10 k,
CL = 100 pF
25°C 10 10 dB
Full range is −40°C to 125°C for Q level part, −55°C to 125°C for M level part.
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
26 POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TLC2274Q and TLC2274M electrical characteristics at specified free-air temperature, VDD = 5 V
(unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
TLC2274Q,
TLC2274M TLC2274AQ,
TLC2274AM
UNIT
PARAMETER
TEST CONDITIONS
TA
MIN TYP MAX MIN TYP MAX
UNIT
Input offset voltage
25°C 300 2500 300 950
µV
IO
Input offset voltage
Full range 3000 1500 µ
V
Temperature coefficient
25
°
C
2
2
µV/°C
αVIO
Temperature coefficient
of input offset voltage
25 C
to 125°C
2
2
µ
V/
°
C
Input offset voltage
long-term drift
(see Note 4) VDD± = ±2.5 V
,
VO = 0 V, VIC = 0 V,
RS = 50 25°C0.002 0.002 µV/mo
Input offset current
O
S
25°C 0.5 60 0.5 60
pA
IO
Input offset current
Full range 800 800
pA
Input bias current
25°C 1 60 1 60
pA
IB
Input bias current
Full range 800 800
pA
25 C
0
0.3
0
0.3
Common-mode input
25
°
C
0
to 4
0.3
to 4.2
0
to 4
0.3
to 4.2
Common-mode input
RS = 50
|VIO |≤ 5 mV
25 C
to 4 to 4.2 to 4 to 4.2
V
ICR
Common-mode input
voltage
R
S
= 50
Ω, |
V
IO
| ≤
5 mV
Full range
0 to
0 to
V
voltage
RS = 50 ,
|VIO | 5 mV
Full range
0 to
3.5
0 to
3.5
V
Full range
3.5 3.5
IOH = −20 µA 25°C 4.99 4.99
High-level output
IOH = −200 µA
25°C 4.85 4.93 4.85 4.93
V
High-level output
voltage
I
OH
= −200
µ
A
Full range 4.85 4.85 V
voltage
IOH = −1 mA
25°C 4.25 4.65 4.25 4.65
V
I
OH
= −1 mA
Full range 4.25 4.25
VIC = 2.5 V, IOL = 50 µA 25°C 0.01 0.01
Low-level output
VIC = 2.5 V,
25°C 0.09 0.15 0.09 0.15
V
Low-level output
voltage
VIC = 2.5 V,
IOL = 500 µAFull range 0.15 0.15 V
voltage
VIC = 2.5 V,
IOL = 5 mA
25°C 0.9 1.5 0.9 1.5
V
V
IC
= 2.5 V,
I
OL
= 5
m
A
Full range 1.5 1.5
Large-signal differential
VIC = 2.5 V,
RL = 10 k
25°C 10 35 10 35
A
Large-signal differential
voltage amplification
VIC = 2.5 V,
VO = 1 V to 4 V
RL = 10 k
Full range 10 10 V/mV
voltage amplification
V
O
= 1 V to 4 V
RL = 1 M25°C 175 175
V/mV
rid Differential input
resistance 25°C 1012 1012
riCommon-mode input
resistance 25°C 1012 1012
ciCommon-mode input
capacitance f = 10 kHz, N package 25°C 8 8 pF
zoClosed-loop output
impedance f = 1 MHz, AV = 10 25°C 140 140
Common-mode
VIC = 0 V to 2.7 V,
25°C 70 75 70 75
dB
Common-mode
rejection ratio
VIC = 0 V to 2.7 V,
VO = 2.5 V, RS = 50 Full range 70 70
dB
Supply-voltage rejection
VDD = 4.4 V to 16 V,
25°C 80 95 80 95
dB
SVR
Supply-voltage rejection
ratio (VDD/VIO)
VDD = 4.4 V to 16 V,
VIC = VDD/2, No load Full range 80 80
dB
Supply current
VO = 2.5 V,
No load
25°C 4.4 6 4.4 6
mA
IDD Supply current VO = 2.5 V, No load Full range 6 6 mA
Full range is −40°C to 125°C for Q level part, −55°C to 125°C for M level part.
Referenced to 2.5 V
NOTE 4: Typical values are based on the input of fset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
27
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TLC2274Q and TLC2274M operating characteristics at specified free-air temperature, VDD = 5 V
PARAMETER
TEST CONDITIONS
TA
TLC2274Q,
TLC2274M TLC2274AQ,
TLC2274AM
UNIT
PARAMETER
TEST CONDITIONS
TA
MIN TYP MAX MIN TYP MAX
UNIT
Slew rate at unity
VO = 0.5 V to 2.5 V,
CL = 100 pF
25°C2.3 3.6 2.3 3.6
SR Slew rate at unity
gain
VO = 0.5 V to 2.5 V,
RL = 10 k,
CL = 100 pF
Full
1.7
1.7
V/µs
SR
gain
RL = 10 k,
Full
range 1.7 1.7
V/µs
Vn
Equivalent input
f = 10 Hz 25°C 50 50
nV/Hz
Vn
Equivalent input
noise voltage f = 1 kHz 25°C 9 9 nV/Hz
VN(PP)
Peak-to-peak
equivalent input
f = 0.1 Hz to 1 Hz 25°C 1 1
V
VN(PP)
equivalent input
noise voltage f = 0.1 Hz to 10 Hz 25°C 1.4 1.4 µV
InEquivalent input
noise current 25°C 0.6 0.6 fA/Hz
Total harmonic
VO = 0.5 V to 2.5 V,
AV = 1 0.0013% 0.0013%
THD + N
Total harmonic
distortion plus
noise
VO = 0.5 V to 2.5 V,
f = 20 kHz,
R = 10 k
AV = 10 25°C0.004% 0.004%
THD + N
distortion plus
noise
f = 20 kHz,
RL = 10 kAV = 100
25 C
0.03% 0.03%
Gain-bandwidth
f = 10 kHz,
RL = 10 k
,
25°C
2.18
2.18
MHz
Gain-bandwidth
product
f = 10 kHz,
C
L
= 100 pF
RL = 10 k,
25°C 2.18 2.18 MHz
BOM
Maximum out-
put-swing band-
VO(PP) = 2 V,
AV = 1,
25°C
1
1
MHz
BOM
put-swing band-
width
VO(PP) = 2 V,
RL = 10 k,
AV = 1,
CL = 100 pF25°C1 1 MHz
AV = −1,
To 0.1%
1.5
1.5
ts
Settling time
AV = −1,
Step = 0.5 V to 2.5 V,
To 0.1%
25°C
1.5 1.5
s
tsSettling time
Step = 0.5 V to 2.5 V,
R
L
= 10 k,
To 0.01%
25°C
2.6
2.6
µs
s
RL = 10 k,
C
L
= 100 pFTo 0.01% 2.6 2.6
φmPhase margin at
unity gain
RL = 10 k
,
CL = 100 pF
25°C50°50°
Gain margin
RL = 10 k,
CL = 100 pF
25°C 10 10 dB
Full range is −40°C to 125°C for Q level part, −55°C to 125°C for M level part.
Referenced to 2.5 V
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
28 POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TLC2274Q and TLC2274M electrical characteristics at specified free-air temperature, VDD± = ±5 V
(unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
TLC2274Q,
TLC2274M TLC2274AQ,
TLC2274AM
UNIT
PARAMETER
TEST CONDITIONS
TA
MIN TYP MAX MIN TYP MAX
UNIT
Input offset voltage
25°C 300 2500 300 950
V
VIO Input offset voltage Full range 3000 1500 µV
Temperature coefficient of
25
°
C
2
2
V/°C
αVIO
Temperature coefficient of
input offset voltage
25 C
to 125°C2 2 µV/°C
Input offset voltage long-
term drift (see Note 4) VIC = 0 V,
R
S
= 50 VO = 0 V, 25°C0.002 0.002 µV/mo
Input offset current
RS = 50
25°C 0.5 60 0.5 60
pA
IIO Input offset current Full range 800 800 pA
Input bias current
25°C 1 60 1 60
pA
IIB Input bias current Full range 800 800 pA
−5
5.3
−5
5.3
Common-mode input
25
°
C
−5
to 4
5.3
to 4.2
−5
to 4
5.3
to 4.2
Common-mode input
RS = 50
|VIO |≤ 5 mV
25°C
to 4 to 4.2 to 4 to 4.2
V
V
Common-mode input
voltage
R
S
= 50 Ω, |V
IO
| ≤ 5 mV
−5
−5
V
voltage
RS = 50 ,
|VIO | 5 mV
Full range
−5
to 3.5
−5
to 3.5
V
Full range
to 3.5 to 3.5
IO = −20 µA 25°C 4.99 4.99
Maximum positive peak
IO = −200 A
25°C 4.85 4.93 4.85 4.93
V
Maximum positive peak
output voltage
IO = −200 µAFull range 4.85 4.85 V
output voltage
IO = −1 mA
25°C 4.25 4.65 4.25 4.65
V
IO = −1 mA Full range 4.25 4.25
VIC = 0 V, IO = 50 µA 25°C 4.99 4.99
Maximum negative peak
VIC = 0 V,
IO = 500 A
25°C 4.85 4.91 4.85 4.91
V
Maximum negative peak
output voltage
VIC = 0 V, IO = 500 µAFull range 4.85 4.85 V
output voltage
VIC = 0 V,
IO = 5 mA
25°C 3.5 4.1 3.5 4.1
V
VIC = 0 V, IO = 5 mAFull range 3.5 3.5
Large-signal differential
RL = 10 k
25°C 20 50 20 50
A
Large-signal differential
voltage amplification
V
O
= ±4 V RL = 10 kFull range 20 20 V/mV
voltage amplification
VO = ±4 V
RL = 1 M25°C 300 300
V/mV
rid Differential input resistance 25°C 1012 1012
riCommon-mode input
resistance 25°C 1012 1012
ciCommon-mode input
capacitance f = 10 kHz, N package 25°C 8 8 pF
zoClosed-loop output
impedance f = 1 MHz, AV = 10 25°C 130 130
Common-mode rejection
VIC = −5 V to 2.7 V
25°C 75 80 75 80
dB
CMRR
Common-mode rejection
ratio
VIC = −5 V to 2.7 V
VO = 0 V, RS = 50 Full range 75 75 dB
Supply-voltage rejection
VDD± =
±
2.2 V to
±
8 V,
25°C 80 95 80 95
dB
kSVR
Supply-voltage rejection
ratio (VDD±/VIO)
VDD± = ± 2.2 V to ±8 V,
VIC = 0 V, No load Full range 80 80 dB
Supply current
VO = 0 V,
No load
25°C 4.8 6 4.8 6
mA
DD
Supply current
V
O
= 0 V,
No load
Full range 6 6
mA
Full range is −40°C to 125°C for Q level part, −55°C to 125°C for M level part.
NOTE 4: Typical values are based on the input of fset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
29
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TLC2274Q and TLC2274M operating characteristics at specified free-air temperature,
VDD± = ±5 V
PARAMETER
TEST CONDITIONS
TA
TLC2274Q,
TLC2274M TLC2274AQ,
TLC2274AM
UNIT
PARAMETER
TEST CONDITIONS
TA
MIN TYP MAX MIN TYP MAX
UNIT
Slew rate at unity
VO = ±2.3 V,
RL = 10 k,
25°C 2.3 3.6 2.3 3.6
SR Slew rate at unity
gain
VO = ±2.3 V,
CL = 100 pF
RL = 10 k,
Full
1.7
1.7
V/µs
SR
gain
CL = 100 pF
Full
range 1.7 1.7
V/µs
Vn
Equivalent input
f = 10 Hz 25°C 50 50
nV/Hz
Vn
Equivalent input
noise voltage f = 1 kHz 25°C 9 9 nV/Hz
VN(PP)
Peak-to-peak
equivalent input
f = 0.1 Hz to 1 Hz 25°C 1 1
V
VN(PP)
equivalent input
noise voltage f = 0.1 Hz to 10 Hz 25°C 1.4 1.4 µV
InEquivalent input
noise current 25°C 0.6 0.6 fA/Hz
Total harmonic
VO = ±2.3 V,
AV = 1 0.0011% 0.0011%
THD + N
Total harmonic
distortion plus
noise
VO = ±2.3 V,
R
L
= 10 kΩ,
f = 20 kHz
AV = 10 25°C0.004% 0.004%
THD + N
distortion plus
noise
RL = 10 kΩ,
f = 20 kHz AV = 100
25 C
0.03% 0.03%
Gain-bandwidth
f = 10 kHz,
RL = 10 k
,
25°C
2.25
2.25
MHz
Gain-bandwidth
product
f = 10 kHz,
CL = 100 pF
RL = 10 k,
25°C 2.25 2.25 MHz
BOM
Maximum
output-swing
VO(PP) = 4.6 V,
AV = 1,
25°C
0.54
0.54
MHz
BOM
output-swing
bandwidth
VO(PP) = 4.6 V,
RL = 10 k,
AV = 1,
CL = 100 pF 25°C 0.54 0.54 MHz
AV = −1,
To 0.1%
1.5
1.5
ts
Settling time
AV = −1,
Step = −2.3 V to 2.3 V,
To 0.1%
25°C
1.5 1.5
s
tsSettling time
Step = −2.3 V to 2.3 V,
R
L
= 10 k,
To 0.01%
25°C
3.2
3.2
µs
s
RL = 10 k,
C
L
= 100 pF To 0.01% 3.2 3.2
φmPhase margin at
unit gain
RL = 10 k
,
CL = 100 pF
25°C 52°52°
Gain margin
RL = 10 k,
CL = 100 pF
25°C 10 10 dB
Full range is −40°C to 125°C for Q level part, −55°C to 125°C for M level part.
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
30 POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
VIO
Input offset voltage
Distribution
1 − 4
VIO Input offset voltage
Distribution
vs Common-mode voltage
1 − 4
5, 6
αVIO Input offset voltage temperature coefficient Distribution 7 − 10
IIB/IIO Input bias and input offset current vs Free-air temperature 11
VI
Input voltage
vs Supply voltage
12
VIInput voltage
vs Supply voltage
vs Free-air temperature
12
13
VOH High-level output voltage vs High-level output current 14
VOL Low-level output voltage vs Low-level output current 15, 16
VOM+ Maximum positive peak output voltage vs Output current 17
VOM Maximum negative peak output voltage vs Output current 18
VO(PP) Maximum peak-to-peak output voltage vs Frequency 19
IOS
Short-circuit output current
vs Supply voltage
20
IOS Short-circuit output current
vs Supply voltage
vs Free-air temperature
20
21
VOOutput voltage vs Differential input voltage 22, 23
Large-signal differential voltage amplification vs Load resistance 24
AVD Large-signal differential voltage amplification
and phase margin vs Frequency 25, 26
Large-signal differential voltage amplification vs Free-air temperature 27, 28
zoOutput impedance vs Frequency 29, 30
CMRR
Common-mode rejection ratio
vs Frequency
31
CMRR Common-mode rejection ratio
vs Frequency
vs Free-air temperature
31
32
kSVR
Supply-voltage rejection ratio
vs Frequency
33, 34
kSVR Supply-voltage rejection ratio
vs Frequency
vs Free-air temperature
33, 34
35
IDD
Supply current
vs Supply voltage
36, 37
IDD Supply current
vs Supply voltage
vs Free-air temperature
36, 37
38, 39
SR
Slew rate
vs Load capacitance
40
SR Slew rate
vs Load capacitance
vs Free-air temperature
40
41
Inverting large-signal pulse response 42, 43
VO
Voltage-follower large-signal pulse response 44, 45
VOInverting small-signal pulse response 46, 47
Voltage-follower small-signal pulse response 48, 49
VnEquivalent input noise voltage vs Frequency 50, 51
Noise voltage over a 10-second period 52
Integrated noise voltage vs Frequency 53
THD + N Total harmonic distortion plus noise vs Frequency 54
Gain-bandwidth product
vs Supply voltage
55
Gain-bandwidth product
vs Supply voltage
vs Free-air temperature
55
56
φmPhase margin vs Load capacitance 57
Gain margin vs Load capacitance 58
NOTE: For all graphs where VDD = 5 V, all loads are referenced to 2.5 V.
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
31
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
VIO − Input Offset Voltage − mV
Percentage of Amplifiers − %
DISTRIBUTION OF TLC2272
INPUT OFFSET VOLTAGE
10
5
0
20
15
−1.6 −1.2 0 0.4 0.8 1.2 1.6
891 Amplifiers From
0.8 0.4
2 Wafer Lots
VDD = ±2.5 V
TA = 25°C
Figure 1
VIO − Input Offset Voltage − mV
Percentage of Amplifiers − %
DISTRIBUTION OF TLC2272
INPUT OFFSET VOLTAGE
10
5
0
20
15
−1.6 −1.2 0 0.4 0.8 1.2 1.6
0.8 0.4
891 Amplifiers From
2 Wafer Lots
VDD = ±5 V
TA = 25°C
Figure 2
Figure 3
VIO − Input Offset Voltage − mV
Percentage of Amplifiers − %
DISTRIBUTION OF TLC2274
INPUT OFFSET VOLTAGE
10
5
0
20
15
0 0.4 0.8 1.2 1.6
992 Amplifiers From
1.6 1.2 0.8 0.4
2 Wafer Lots
VDD = ±2.5 V
Figure 4
VIO − Input Offset Voltage − mV
Percentage of Amplifiers − %
DISTRIBUTION OF TLC2274
INPUT OFFSET VOLTAGE
10
5
0
20
15
0 0.4 0.8 1.2 1.6
992 Amplifiers From
1.6 1.2 0.8 0.4
2 Wafer Lots
VDD = ±5 V
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
32 POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
0.5
0
−1−1 0 1
VIO − Input Offset Voltage − mV
1
2345
VIO
VIC − Common-Mode Voltage − V
VDD = 5 V
TA = 25°C
RS = 50
0.5
INPUT OFFSET VOLTAGE
vs
COMMON-MODE VOLTAGE
Figure 5
0.5
0
−1 −1 0 1
VIO − Input Offset Voltage − mV
1
2345
INPUT OFFSET VOLTAGE
vs
COMMON-MODE VOLTAGE
VIC − Common-Mode Voltage − V
VIO
0.5
VDD = ±5 V
TA = 25°C
RS = 50
−6 −5 −4 −3 −2
Figure 6
15
10
5
0−1 0 1
Percentage of Amplifiers − %
20
25
2345
DISTRIBUTION OF TLC2272
vs
INPUT OFFSET VOLTAGE TEMPERATURE
COEFFICIENT
αVIO − Temperature Coefficient − µV/°C
128 Amplifiers From
2 Wafer Lots
VDD = ±2.5 V
P Package
25°C to 125°C
−5 −4 −3 −2
Figure 7
−5 −4 −3 −2
15
10
5
0−1 0 1
Percentage of Amplifiers − %
20
25
2345
DISTRIBUTION OF TLC2272
vs
INPUT OFFSET VOLTAGE TEMPERATURE
COEFFICIENT
αVIO − Temperature Coefficient − µV/°C
128 Amplifiers From
2 Wafer Lots
VDD = ±5 V
P Package
25°C to 125°C
Figure 8
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
33
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
15
10
5
001
Percentage of Amplifiers − %
20
25
2345
DISTRIBUTION OF TLC2274
vs
INPUT OFFSET VOLTAGE TEMPERATURE
COEFFICIENT
αVIO − Temperature Coefficient − µV/°C
−5 −4 −3 −2 −1
128 Amplifiers From
2 Wafer Lots
VDD = ±2.5 V
N Package
TA = 25°C to 125°C
Figure 9
15
10
5
0
Percentage of Amplifiers − %
20
25
DISTRIBUTION OF TLC2274
vs
INPUT OFFSET VOLTAGE TEMPERATURE
COEFFICIENT
αVIO − Temperature Coefficient − µV/°C
012345
−5 −4 −3 −2 −1
128 Amplifiers From
2 Wafer Lots
VDD = ±2.5 V
N Package
TA = 25°C to 125°C
Figure 10
15
10
5
025 45 65 85
20
25
30
105 125
INPUT BIAS AND INPUT OFFSET CURRENT
vs
FREE-AIR TEMPERATURE
TA − Free-Air Temperature − °C
35 VDD = ±2.5 V
VIC = 0 V
VO = 0 V
RS = 50
IIB
IIO
IIB and IIO − Input Bias and Input Offset Currents − pA
IB
IIIO
Figure 11
0
− 2
− 6
− 8
− 10
8
− 4
2345678
− Input Voltage − V
4
2
6
10
INPUT VOLTAGE
vs
SUPPLY VOLTAGE
|VDD±| − Supply Voltage − V
VI
TA = 25°C
RS = 50
|VIO| 5mV
12
Figure 12
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
34 POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
−75 − 25 0 25 50 75 100 125
2
1
0
−1
3
4
5
− Input Voltage − V
VI
INPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
TA − Free-Air Temperature − °C
|VIO| 5mV
VDD = 5 V
−50
Figure 13
V0H − High-Level Output Voltage − V
VOH
IOH − High-Level Output Current − mA
4
2
1
0
6
3
01234
5
HIGH-LEVEL OUTPUT VOLTAGE
vs
HIGH-LEVEL OUTPUT CURRENT
VDD = 5 V
TA = 125°C
TA = −55°C
TA = 25°C
Figure 14
VOL − Low-Level Output Voltage − V
0.6
0.4
0.2
00123
0.8
45
VDD = 5 V
TA = 25°C
IOL − Low-Level Output Current − mA
VOL
VIC = 1.25 V
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT CURRENT
1
1.2
VIC = 2.5 V
Figure 15
VIC = 0 V
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT CURRENT
VOL − Low-Level Output Voltage − V
IOL − Low-Level Output Current − mA
VOL
0.6
0.4
0.2
00123
0.8
4
1
1.2
56
1.4 VDD = 5 V
VIC = 2.5 V
TA = 125°C
TA = 25°C
TA = −55°C
Figure 16
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
35
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
3
2
1012 3 4 5
− Maximum Positive Peak Output Voltage − V
4
5
MAXIMUM POSITIVE PEAK OUTPUT VOLTAGE
vs
OUTPUT CURRENT
|IO| − Output Current − mA
TA = −55°C
TA = 25°C
TA = 125°C
VDD± = ±5 V
VOM +
Figure 17
0123456
IO − Output Current − mA
MAXIMUM NEGATIVE PEAK OUTPUT VOLTAGE
vs
OUTPUT CURRENT
VDD = ±5 V
VIC = 0 V
TA = 125°C
TA = 25°C
TA = −55°C
3.8
−4
4.2
4.4
4.6
4.8
−5
− Maximum Negative Peak Output Voltage − V
VOM −
Figure 18
Figure 19
2
1
0
10 k 100 k 1 M
3
f − Frequency − Hz
4
10 M
6
5
7
8
9
10
MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE
vs
FREQUENCY
V(OPP) − Maximum Peak-to-Peak Output Voltage − VVO(PP)
VDD = 5 V
VDD = ±5 V
RL = 10 k
TA = 25°C
Figure 20
4
0
23 4
8
12
16
5678
IOS − Short-Circuit Output Current − mA
OS
I
|VDD±| − Supply Voltage − V
SHORT-CIRCUIT OUTPUT CURRENT
vs
SUPPLY VOLTAGE
VID = 100 mV
VO = 0 V
TA = 25°C
−8
VID = −100 mV
−4
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
36 POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
−5
SHORT-CIRCUIT OUTPUT CURRENT
vs
FREE-AIR TEMPERATURE
75 50 25 0 25 50 75 100 125
−1
−3
7
11
15
IOS − Short-Circuit Output Current − mA
OS
I
TA − Free-Air Temperature − °C
VID = 100 mV
VID = −100 mV
VO = 0 V
VDD = ±5 V
Figure 21
OUTPUT VOLTAGE
vs
DIFFERENTIAL INPUT VOLTAGE
3
2
1
0800
4
5
1200
VID − Differential Input Voltage − µV
− Output Voltage − V
VO
800 400 4000
VDD = 5 V
TA = 25°C
RL = 10 k
VIC = 2.5 V
Figure 22
1
−1
−3
−5 0 250
3
5
OUTPUT VOLTAGE
vs
DIFFERENTIAL INPUT VOLTAGE
500 750 1000
VID − Differential Input Voltage − µV
− Output Voltage − V
VO
1000 750 250500
Figure 23
VDD = ±5 V
TA = 25°C
RL = 10 k
VIC = 0 V
0.1
1
0.1 1 10 100
10
100
1000
LARGE-SIGNAL DIFFERENTIAL
VOLTAGE AMPLIFICATION
vs
LOAD RESISTANCE
RL − Load Resistance − k
VO = ±1 V
TA = 25°C
VDD = ±5 V
VDD = 5 V
Figure 24
AVD − Large-Signal Differential
ÁÁ
ÁÁ
ÁÁ
AVD
Voltage Amplification − dB
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
37
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
0
20
1 k 10 k 100 k 1 M
40
60
80
LARGE-SIGNAL DIFFERENTIAL VOLTAGE
AMPLIFICATION AND PHASE MARGIN
vs
FREQUENCY
f − Frequency − Hz
10 M
om − Phase Margin
φm
VDD = 5 V
RL = 10 k
CL = 100 pF
TA = 25°C
−20
−40 −90°
−45°
0°
45°
90°
135°
180°
AVD − Large-Signal Differential
ÁÁ
ÁÁ
ÁÁ
AVD
Voltage Amplification − dB
Figure 25
0
20
1 k 10 k 100 k 1 M
40
60
80
LARGE-SIGNAL DIFFERENTIAL VOLTAGE
AMPLIFICATION AND PHASE MARGIN
vs
FREQUENCY
f − Frequency − Hz 10 M
VDD = ±5 V
RL = 10 k
CL = 100 pF
TA = 25°C
om − Phase Margin
φm
−20
−40 −90°
−45°
0°
45°
90°
135°
180°
AVD − Large-Signal Differential
ÁÁ
ÁÁ
ÁÁ
AVD
Voltage Amplification − dB
Figure 26
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
38 POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
LARGE-SIGNAL DIFFERENTIAL
VOLTAGE AMPLIFICATION
vs
FREE-AIR TEMPERATURE
75 50 25 0 25 50 75 100 125
10
100
1 k
TA − Free-Air Temperature − °C
VDD = 5 V
VIC = 2.5 V
VO = 1 V to 4 V
RL = 1 M
RL = 10 k
AVD − Large-Signal Differential
ÁÁ
ÁÁ
AVD
Voltage Amplification − V/mV
Figure 27
LARGE-SIGNAL DIFFERENTIAL
VOLTAGE AMPLIFICATION
vs
FREE-AIR TEMPERATURE
75 50 25 0 25 50 75 100 125
10
100
1 k
TA − Free-Air Temperature − °C
RL = 1 M
RL = 10 k
VDD = ±5 V
VIC = 0 V
VO = ±4 V
AVD − Large-Signal Differential
ÁÁ
ÁÁ
AVD
Voltage Amplification − V/mV
Figure 28
10
1
0.1
1000
100
100 1 k 10 k 100 k 1 M
zo − Output Impedance − O
f − Frequency − Hz
zo
OUTPUT IMPEDANCE
vs
FREQUENCY
VDD = 5 V
TA = 25°C
AV = 100
AV = 10
AV = 1
Figure 29
10
1
0.1
1000
100
100 1 k 10 k 100 k 1 M
zo − Output Impedance − O
f − Frequency − Hz
zo
OUTPUT IMPEDANCE
vs
FREQUENCY
VDD = ±5 V
TA = 25°C
AV = 100
AV = 10
AV = 1
Figure 30
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
39
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
COMMON-MODE REJECTION RATIO
vs
FREQUENCY
60
40
20
010 100 1 k 10 k
CMRR − Common-Mode Rejection Ratio − dB
80
100
100 k 1 M
f − Frequency − Hz
VDD = ±5 V
VDD = 5 V
10 M
TA = 25°C
Figure 31
TA − Free-Air Temperature − °C
CMRR − Common-Mode Rejection Ratio − dB
COMMON-MODE REJECTION RATIO
vs
FREE-AIR TEMPERATURE
82
78
74
70
86
90
75 50 25 0 25 50 75 100 125
VDD = ±5 V
VDD = 5 V
VIC = 0 V to 2.7 V
VIC = −5 V to 2.7 V
Figure 32
40
20
0
10 100 1 k
kSVR − Supply-Voltage Rejection Ratio − dB
60
80
f − Frequency − Hz
100
10 k 100 k 1 M 10 M
SUPPLY-VOLTAGE REJECTION RATIO
vs
FREQUENCY
kSVR
VDD = 5 V
TA = 25°C
kSVR+
kSVR
−20
Figure 33
40
20
0
10 100 1 k
kSVR − Supply-Voltage Rejection Ratio − dB
60
80
f − Frequency − Hz
100
10 k 100 k 1 M 10 M
SUPPLY-VOLTAGE REJECTION RATIO
vs
FREQUENCY
kSVR
VDD = ±5 V
TA = 25°C
kSVR+
kSVR
−20
Figure 34
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
40 POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
kSVR − Supply Voltage Rejection Ratio − dB
SUPPLY VOLTAGE REJECTION RATIO
vs
FREE-AIR TEMPERATURE
kSVR
TA − Free-Air Temperature − °C
75 50 25 0 25 50 75 100 125
100
95
90
85
105
110 VDD± = ±2.2 V to ±8 V
VO = 0 V
Figure 35
012345678
0
0.6
1.2
1.8
2.4
3
IDD − Supply Current − mA
DD
I
|VDD±| − Supply Voltage − V
VO = 0 V
No Load
TA = 25°C
TA = −55°C
TA = 125°C
Figure 36
TLC2272
SUPPLY CURRENT
vs
SUPPLY VOLTAGE
Figure 37
012345678
0
1.2
2.4
3.6
4.8
6
IDD − Supply Current − mA
DD
I
|VDD±| − Supply Voltage − V
VO = 0 V
No Load
TA = 25°C
TA = −55°C
TA = 125°C
TLC2274
SUPPLY CURRENT
vs
SUPPLY VOLTAGE
Figure 38
75 50 25 0 25 50 75 100 125
0
0.6
1.2
1.8
2.4
3
TA − Free-Air Temperature − °C
IDD − Supply Current − mA
DD
I
VDD = 5 V
VO = 2.5 V
VDD = ±5 V
VO = 0 V
TLC2272
SUPPLY CURRENT
vs
FREE-AIR TEMPERATURE
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
41
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 39
75 50 25 0 25 50 75 100 125
0
1.2
2.4
3.6
4.8
6
TA − Free-Air Temperature − °C
IDD − Supply Current − mA
DD
I
VDD = 5 V
VO = 2.5 V
VDD = ±5 V
VO = 0 V
TLC2274
SUPPLY CURRENT
vs
FREE-AIR TEMPERATURE
µs
SR − Slew Rate − V/
0
1
2
3
CL − Load Capacitance − pF
SLEW RATE
vs
LOAD CAPACITANCE
10 k1 k10010
SR +
SR −
4
5VDD = 5 V
AV = −1
TA = 25°C
Figure 40
3
2
1
4
µs
SR − Slew Rate − V/
75 50 25 0 25 50 75 100 125
TA − Free-Air Temperature − °C
SLEW RATE
vs
FREE-AIR TEMPERATURE
VDD = 5 V
RL = 10 k
CL = 100 pF
AV = 1
SR +
SR −
0
5
Figure 41
INVERTING LARGE-SIGNAL PULSE RESPONSE
2
1
012345
3
4
5
6789
VO − Output Voltage − mV
VO
t − Time − µs
VDD = 5 V
RL = 10 k
CL = 100 pF
TA = 25°C
AV = −1
0
Figure 42
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
42 POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
0
− 1
− 3
− 4
− 5
4
− 2
12345
2
1
3
5
6789
VO − Output Voltage − V
VO
t − Time − µs
VDD = ±5 V
RL = 10 k
CL = 100 pF
TA = 25°C
AV = −1
INVERTING LARGE-SIGNAL PULSE RESPONSE
0
Figure 43
3
2
1
012345
4
5
6789
VO − Output Voltage − V
VO
t − Time − µs
VDD = 5 V
RL = 10 k
CL = 100 pF
AV = 1
TA = 25°C
VOLTAGE-FOLLOWER
LARGE-SIGNAL PULSE RESPONSE
0
Figure 44
VOLTAGE-FOLLOWER
LARGE-SIGNAL PULSE RESPONSE
0
−1
4
12345
2
1
3
5
6789
VO − Output Voltage − V
VO
t − Time − µs
VDD = ±5 V
RL = 10 k
CL = 100 pF
TA = 25°C
AV = 1
0
−2
−3
−5
−4
Figure 45
INVERTING SMALL-SIGNAL PULSE RESPONSE
2.5
2.45
2.4 0.5 1 1.5 2 2.5
2.55
2.6
2.65
3.5 4.5 5 5.5
VO − Output Voltage − V
VO
t − Time − µs
VDD = 5 V
RL = 10 k
CL = 100 pF
TA = 25°C
AV = −1
034
Figure 46
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
43
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
0
−100 0 0.5 1 1.5 2
50
100
2.5 3 3.5 4
VO − Output Voltage − mV
VO
t − Time − µs
INVERTING SMALL-SIGNAL PULSE RESPONSE
VDD = ±5 V
RL = 10 k
CL = 100 pF
TA = 25°C
AV = 1
−50
Figure 47
VOLTAGE-FOLLOWER
SMALL-SIGNAL PULSE RESPONSE
2.5
2.45
2.4
2.55
2.6
0 0.5 1 1.5
VO − Output Voltage − V
VO
t − Time − µs
2.65 VDD = 5 V
RL = 10 k
CL = 100 pF
TA = 25°C
AV = 1
Figure 48
VOLTAGE-FOLLOWER
SMALL-SIGNAL PULSE RESPONSE
0
−50
−100
50
100
0 0.5 1 1.5
VO − Output Voltage − mV
VO
t − Time − µs
VDD = ±5 V
RL = 10 k
CL = 100 pF
TA = 25°C
AV = 1
Figure 49
20
10
0
10 100 1 k
Vn − Equivalent Input Noise Voltage − nV Hz
30
f − Frequency − Hz
40
10 k
EQUIVALENT INPUT NOISE VOLTAGE
vs
FREQUENCY
50
60
VnnV/ Hz
VDD = 5 V
TA = 25°C
RS = 20
Figure 50
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
44 POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
20
10
0
10 100 1 k
Vn − Equivalent Input Noise Voltage − nV Hz
30
f − Frequency − Hz
40
10 k
EQUIVALENT INPUT NOISE VOLTAGE
vs
FREQUENCY
50
60
VnnV/ Hz
VDD = ±5 V
TA = 25°C
RS = 20
Figure 51
−750
−1000 246
0
250
810
Noise Voltage − nV
t − Time − s
NOISE VOLTAGE
OVER A 10 SECOND PERIOD
0
VDD = 5 V
f = 0.1 Hz to 10 Hz
TA = 25°C
500
750
1000
250
500
Figure 52
Integrated Noise Voltage − uVRMS
1
0.1
100
1 10 100 1 k
f − Frequency − Hz
INTEGRATED NOISE VOLTAGE
vs
FREQUENCY
10 k 100 k
VRMS
µ
Calculated Using
Ideal Pass-Band Filter
Lower Frequency = 1 Hz
TA= 25°C
10
Figure 53
0.0001
0.001
100 1 k 10 k 100 k
THD + N − Total Harmonic Distortion Plus Noise − %
f − Frequency − Hz
TOTAL HARMONIC DISTORTION PLUS NOISE
vs
FREQUENCY
0.01
0.1
1VDD = 5 V
TA = 25°C
RL = 10 k
AV = 100
AV = 10
AV = 1
Figure 54
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
45
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 55
Gain-Bandwidth Product − MHz
2.1
2012345
2.2
2.3
678
|VDD±| − Supply Voltage − V
2.4
2.5
GAIN-BANDWIDTH PRODUCT
vs
SUPPLY VOLTAGE
f = 10 kHz
RL = 10 k
CL = 100 pF
TA = 25°C
Figure 56
75 50 25 0 25 50 75 100 125
TA − Free-Air Temperature − °C
Gain-Bandwidth Product − MHz
GAIN-BANDWIDTH PRODUCT
vs
FREE-AIR TEMPERATURE
1.8
1.6
1.4
2
2.4
2.2
2.6
2.8
3VDD = 5 V
f = 10 kHz
RL = 10 k
CL = 100 pF
10
om − Phase Margin
10000
CL − Load Capacitance − pF
φm
PHASE MARGIN
vs
LOAD CAPACITANCE
1000100
VDD = ±5 V
TA = 25°C
Rnull = 20
Rnull = 10
Rnull = 0
75°
60°
45°
30°
15°
0°
10 k
10 k
VDD
VDD+ Rnull
CL
VI
Rnull = 100
Rnull = 50
Figure 57 Figure 58
3
010
Gain Margin − dB
6
9
10000
CL − Load Capacitance − pF
12
15
GAIN MARGIN
vs
LOAD CAPACITANCE
1000100
VDD = 5 V
AV = 1
RL = 10 k
TA = 25°C
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
 
  
 
SLOS190G − FEBRUAR Y 1997 − REVISED MAY 2004
46 POST OFFICE BOX 655303 DALLAS, TEXAS 75265
APPLICATION INFORMATION
macromodel information
Macromodel information provided was derived using Microsim Parts, the model generation software used
with Microsim PSpice. The Boyle macromodel (see Note 5) and subcircuit in Figure 59 were generated using
the TLC227x typical electrical and operating characteristics at TA = 25°C. Using this information, output
simulations of the following key parameters can be generated to a tolerance of 20% (in most cases):
DMaximum positive output voltage swing
DMaximum negative output voltage swing
DSlew rate
DQuiescent power dissipation
DInput bias current
DOpen-loop voltage amplification
DUnity gain frequency
DCommon-mode rejection ratio
DPhase margin
DDC output resistance
DAC output resistance
DShort-circuit output current limit
NOTE 5: G . R . Boyle, B. M. Cohn, D. O. Pederson, and J. E. Solomon, “Macromodeling of Integrated Circuit Operational Amplifiers”, IEEE Journal
of Solid-State Circuits, SC-9, 353 (1974).
OUT
+
+
+
+
+
+
+
+
+
.SUBCKT TLC227x 1 2 3 4 5
C1 11 1214E−12
C2 6 760.00E−12
DC 5 53DX
DE 54 5DX
DLP 90 91DX
DLN 92 90DX
DP 4 3DX
EGND 99 0POLY (2) (3,0) (4,) 0 .5 .5
FB 99 0POLY (5) VB VC VE VLP VLN 0
+ 984.9E3 −1E6 1E6 1E6 −1E6
GA 6 011 12 377.0E−6
GCM 0 6 10 99 134E−9
ISS 3 10DC 216.OE−6
HLIM 90 0VLIM 1K
J1 11 210 JX
J2 12 110 JX
R2 6 9100.OE3
RD1 60 112.653E3
RD2 60 122.653E3
R01 8 550
R02 7 9950
RP 3 44.310E3
RSS 10 99925.9E3
VAD 60 4−.5
VB 9 0DC 0
VC 3 53 DC .78
VE 54 4DC .78
VLIM 7 8DC 0
VLP 91 0DC 1.9
VLN 0 92DC 9.4
.MODEL DX D (IS=800.0E−18)
.MODEL JX PJF (IS=1.500E−12BETA=1.316E-3
+ VTO=−.270)
.ENDS
VCC+
RP
IN 2
IN+ 1
VCC
VAD
RD1
11
J1 J2
10
RSS ISS
3
12
RD2
60
VE
54 DE
DP
VC
DC
4
C1
53
R2 6
9
EGND
VB
FB
C2
GCM GA VLIM
8
5RO1
RO2
HLIM
90 DIP
91
DIN
92
VINVIP
99
7
Figure 59. Boyle Macromodel and Subcircuit
PSpice and Parts are trademarks of MicroSim Corporation.
!'# #!$'" !'#  ") !'# % &+ 
"'+  "'+  " *" &+  # $''+ %#", ''
 ") #%"  %", )"#"#  ")
#!$" %$" " *)) ") !' '"#(
PACKAGE OPTION ADDENDUM
www.ti.com 25-Sep-2013
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
5962-9318201M2A ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 5962-
9318201M2A
TLC2274
MFKB
5962-9318201MCA ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type -55 to 125 5962-9318201MC
A
TLC2274MJB
5962-9318201QDA ACTIVE CFP W 14 1 TBD A42 N / A for Pkg Type -55 to 125 5962-9318201QD
A
TLC2274MWB
5962-9318202Q2A ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 5962-
9318202Q2A
TLC2274
AMFKB
5962-9318202QCA ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type -55 to 125 5962-9318202QC
A
TLC2274AMJB
5962-9318202QDA ACTIVE CFP W 14 1 TBD A42 N / A for Pkg Type -55 to 125 5962-9318202QD
A
TLC2274AMWB
5962-9555201NXD ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -55 to 125 Q2272M
5962-9555201NXDR ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -55 to 125 Q2272M
5962-9555201Q2A ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 5962-
9555201Q2A
TLC2272
MFKB
5962-9555201QHA ACTIVE CFP U 10 1 TBD A42 N / A for Pkg Type -55 to 125 9555201QHA
TLC2272M
5962-9555201QPA ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 9555201QPA
TLC2272M
5962-9555202Q2A ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 5962-
9555202Q2A
TLC2272
AMFKB
PACKAGE OPTION ADDENDUM
www.ti.com 25-Sep-2013
Addendum-Page 2
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
5962-9555202QHA ACTIVE CFP U 10 1 TBD A42 N / A for Pkg Type -55 to 125 9555202QHA
TLC2272AM
5962-9555202QPA ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 9555202QPA
TLC2272AM
TLC2272ACD ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 2272AC
TLC2272ACDG4 ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 2272AC
TLC2272ACDR ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 2272AC
TLC2272ACDRG4 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 2272AC
TLC2272ACP ACTIVE PDIP P 8 50 Pb-Free
(RoHS) CU NIPDAU N / A for Pkg Type TLC2272AC
TLC2272ACPE4 ACTIVE PDIP P 8 50 Pb-Free
(RoHS) CU NIPDAU N / A for Pkg Type TLC2272AC
TLC2272ACPW ACTIVE TSSOP PW 8 150 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM P2272A
TLC2272ACPWG4 ACTIVE TSSOP PW 8 150 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM P2272A
TLC2272ACPWLE OBSOLETE TSSOP PW 8 TBD Call TI Call TI
TLC2272ACPWR ACTIVE TSSOP PW 8 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM P2272A
TLC2272ACPWRG4 ACTIVE TSSOP PW 8 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM P2272A
TLC2272AID ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 2272AI
TLC2272AIDG4 ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 2272AI
TLC2272AIDR ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 2272AI
TLC2272AIDRG4 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 2272AI
TLC2272AIP ACTIVE PDIP P 8 50 Pb-Free
(RoHS) CU NIPDAU N / A for Pkg Type TLC2272AI
PACKAGE OPTION ADDENDUM
www.ti.com 25-Sep-2013
Addendum-Page 3
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
TLC2272AIPE4 ACTIVE PDIP P 8 50 Pb-Free
(RoHS) CU NIPDAU N / A for Pkg Type TLC2272AI
TLC2272AMD ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -55 to 125 2272AM
TLC2272AMDG4 ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 2272AM
TLC2272AMDR ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -55 to 125 2272AM
TLC2272AMDRG4 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 2272AM
TLC2272AMFKB ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 5962-
9555202Q2A
TLC2272
AMFKB
TLC2272AMJGB ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 9555202QPA
TLC2272AM
TLC2272AMP OBSOLETE PDIP P 8 TBD Call TI Call TI -55 to 125
TLC2272AMUB ACTIVE CFP U 10 1 TBD A42 N / A for Pkg Type -55 to 125 9555202QHA
TLC2272AM
TLC2272AQD ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 C2272A
TLC2272AQDG4 ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM C2272A
TLC2272AQDR ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 C2272A
TLC2272AQDRG4 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM C2272A
TLC2272CD ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 2272C
TLC2272CDG4 ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 2272C
TLC2272CDR ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 2272C
TLC2272CDRG4 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 2272C
PACKAGE OPTION ADDENDUM
www.ti.com 25-Sep-2013
Addendum-Page 4
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
TLC2272CP ACTIVE PDIP P 8 50 Pb-Free
(RoHS) CU NIPDAU N / A for Pkg Type 0 to 70 TLC2272CP
TLC2272CPE4 ACTIVE PDIP P 8 50 Pb-Free
(RoHS) CU NIPDAU N / A for Pkg Type 0 to 70 TLC2272CP
TLC2272CPSR ACTIVE SO PS 8 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 P2272
TLC2272CPSRG4 ACTIVE SO PS 8 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 P2272
TLC2272CPW ACTIVE TSSOP PW 8 150 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 P2272
TLC2272CPWG4 ACTIVE TSSOP PW 8 150 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 P2272
TLC2272CPWLE OBSOLETE TSSOP PW 8 TBD Call TI Call TI 0 to 70
TLC2272CPWR ACTIVE TSSOP PW 8 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 P2272
TLC2272CPWRG4 ACTIVE TSSOP PW 8 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 P2272
TLC2272ID ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 2272I
TLC2272IDG4 ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 2272I
TLC2272IDR ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 2272I
TLC2272IDRG4 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 2272I
TLC2272IP ACTIVE PDIP P 8 50 Pb-Free
(RoHS) CU NIPDAU N / A for Pkg Type TLC2272IP
TLC2272IPE4 ACTIVE PDIP P 8 50 Pb-Free
(RoHS) CU NIPDAU N / A for Pkg Type TLC2272IP
TLC2272IPW ACTIVE TSSOP PW 8 150 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Y2272
TLC2272IPWG4 ACTIVE TSSOP PW 8 150 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Y2272
TLC2272IPWLE OBSOLETE TSSOP PW 8 TBD Call TI Call TI
TLC2272IPWR ACTIVE TSSOP PW 8 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Y2272
PACKAGE OPTION ADDENDUM
www.ti.com 25-Sep-2013
Addendum-Page 5
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
TLC2272IPWRG4 ACTIVE TSSOP PW 8 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Y2272
TLC2272MD ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -55 to 125 2272M
TLC2272MDG4 ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 2272M
TLC2272MDR ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -55 to 125 2272M
TLC2272MDRG4 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 2272M
TLC2272MFKB ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 5962-
9555201Q2A
TLC2272
MFKB
TLC2272MJG ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 TLC2272MJG
TLC2272MJGB ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 9555201QPA
TLC2272M
TLC2272MP OBSOLETE PDIP P 8 TBD Call TI Call TI -55 to 125
TLC2272MUB ACTIVE CFP U 10 1 TBD A42 N / A for Pkg Type -55 to 125 9555201QHA
TLC2272M
TLC2272QDG4 ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM C2272Q
TLC2272QDR ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 C2272Q
TLC2272QDRG4 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM C2272Q
TLC2272QPWRG4 ACTIVE TSSOP PW 8 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM T2272Q
TLC2274ACD ACTIVE SOIC D 14 50 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 2274AC
TLC2274ACDG4 ACTIVE SOIC D 14 50 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 2274AC
TLC2274ACDR ACTIVE SOIC D 14 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 2274AC
TLC2274ACDRG4 ACTIVE SOIC D 14 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 2274AC
PACKAGE OPTION ADDENDUM
www.ti.com 25-Sep-2013
Addendum-Page 6
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
TLC2274ACN ACTIVE PDIP N 14 25 Pb-Free
(RoHS) CU NIPDAU N / A for Pkg Type 0 to 70 TLC2274ACN
TLC2274ACNE4 ACTIVE PDIP N 14 25 Pb-Free
(RoHS) CU NIPDAU N / A for Pkg Type 0 to 70 TLC2274ACN
TLC2274ACPW ACTIVE TSSOP PW 14 90 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 P2274A
TLC2274ACPWG4 ACTIVE TSSOP PW 14 90 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 P2274A
TLC2274ACPWR ACTIVE TSSOP PW 14 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 P2274A
TLC2274ACPWRG4 ACTIVE TSSOP PW 14 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 P2274A
TLC2274AID ACTIVE SOIC D 14 50 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 2274AI
TLC2274AIDG4 ACTIVE SOIC D 14 50 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 2274AI
TLC2274AIDR ACTIVE SOIC D 14 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 2274AI
TLC2274AIDRG4 ACTIVE SOIC D 14 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 2274AI
TLC2274AIN ACTIVE PDIP N 14 25 Pb-Free
(RoHS) CU NIPDAU N / A for Pkg Type -40 to 125 TLC2274AIN
TLC2274AINE4 ACTIVE PDIP N 14 25 Pb-Free
(RoHS) CU NIPDAU N / A for Pkg Type -40 to 125 TLC2274AIN
TLC2274AIPW ACTIVE TSSOP PW 14 90 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 Y2274A
TLC2274AIPWG4 ACTIVE TSSOP PW 14 90 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 Y2274A
TLC2274AIPWLE OBSOLETE TSSOP PW 14 TBD Call TI Call TI -40 to 125
TLC2274AIPWR ACTIVE TSSOP PW 14 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 Y2274A
TLC2274AIPWRG4 ACTIVE TSSOP PW 14 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 Y2274A
TLC2274AMD ACTIVE SOIC D 14 50 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -55 to 125 2274AM
PACKAGE OPTION ADDENDUM
www.ti.com 25-Sep-2013
Addendum-Page 7
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
TLC2274AMDG4 ACTIVE SOIC D 14 50 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 2274AM
TLC2274AMDR OBSOLETE SOIC D 14 TBD Call TI Call TI -55 to 125 2274AM
TLC2274AMDRG4 ACTIVE SOIC D 14 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 2274AM
TLC2274AMFKB ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 5962-
9318202Q2A
TLC2274
AMFKB
TLC2274AMJB ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type -55 to 125 5962-9318202QC
A
TLC2274AMJB
TLC2274AMWB ACTIVE CFP W 14 1 TBD A42 N / A for Pkg Type -55 to 125 5962-9318202QD
A
TLC2274AMWB
TLC2274AQD ACTIVE SOIC D 14 50 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 TLC2274A
TLC2274AQDG4 ACTIVE SOIC D 14 50 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PJ2274A
TLC2274AQDR ACTIVE SOIC D 14 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 TLC2274A
TLC2274AQDRG4 ACTIVE SOIC D 14 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PJ2274A
TLC2274CD ACTIVE SOIC D 14 50 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2274C
TLC2274CDG4 ACTIVE SOIC D 14 50 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2274C
TLC2274CDR ACTIVE SOIC D 14 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2274C
TLC2274CDRG4 ACTIVE SOIC D 14 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2274C
TLC2274CN ACTIVE PDIP N 14 25 Pb-Free
(RoHS) CU NIPDAU N / A for Pkg Type TLC2274CN
TLC2274CNE4 ACTIVE PDIP N 14 25 Pb-Free
(RoHS) CU NIPDAU N / A for Pkg Type TLC2274CN
TLC2274CNSR ACTIVE SO NS 14 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2274
PACKAGE OPTION ADDENDUM
www.ti.com 25-Sep-2013
Addendum-Page 8
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
TLC2274CNSRG4 ACTIVE SO NS 14 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2274
TLC2274CPW ACTIVE TSSOP PW 14 90 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM P2274
TLC2274CPWG4 ACTIVE TSSOP PW 14 90 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM P2274
TLC2274CPWLE OBSOLETE TSSOP PW 14 TBD Call TI Call TI
TLC2274CPWR ACTIVE TSSOP PW 14 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM P2274
TLC2274CPWRG4 ACTIVE TSSOP PW 14 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 P2274
TLC2274ID ACTIVE SOIC D 14 50 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2274I
TLC2274IDG4 ACTIVE SOIC D 14 50 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2274I
TLC2274IDR ACTIVE SOIC D 14 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2274I
TLC2274IDRG4 ACTIVE SOIC D 14 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2274I
TLC2274IN ACTIVE PDIP N 14 25 Pb-Free
(RoHS) CU NIPDAU N / A for Pkg Type TLC2274IN
TLC2274INE4 ACTIVE PDIP N 14 25 Pb-Free
(RoHS) CU NIPDAU N / A for Pkg Type TLC2274IN
TLC2274IPW ACTIVE TSSOP PW 14 90 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Y2274
TLC2274IPWG4 ACTIVE TSSOP PW 14 90 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Y2274
TLC2274IPWLE OBSOLETE TSSOP PW 14 TBD Call TI Call TI
TLC2274IPWR ACTIVE TSSOP PW 14 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Y2274
TLC2274IPWRG4 ACTIVE TSSOP PW 14 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Y2274
TLC2274MD ACTIVE SOIC D 14 50 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -55 to 125 TLC2274M
TLC2274MDG4 ACTIVE SOIC D 14 50 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PJ2274M
PACKAGE OPTION ADDENDUM
www.ti.com 25-Sep-2013
Addendum-Page 9
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
TLC2274MDR ACTIVE SOIC D 14 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -55 to 125 TLC2274M
TLC2274MDRG4 ACTIVE SOIC D 14 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PJ2274M
TLC2274MFKB ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 5962-
9318201M2A
TLC2274
MFKB
TLC2274MJ ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type -55 to 125 TLC2274MJ
TLC2274MJB ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type -55 to 125 5962-9318201MC
A
TLC2274MJB
TLC2274MN ACTIVE PDIP N 14 25 Pb-Free
(RoHS) CU NIPDAU N / A for Pkg Type -55 to 125 TLC2274MN
TLC2274MWB ACTIVE CFP W 14 1 TBD A42 N / A for Pkg Type -55 to 125 5962-9318201QD
A
TLC2274MWB
TLC2274QD ACTIVE SOIC D 14 50 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 TLC2274
TLC2274QDG4 ACTIVE SOIC D 14 50 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2274
TLC2274QDR OBSOLETE SOIC D 14 TBD Call TI Call TI -40 to 125 TLC2274
TLC2274QDRG4 ACTIVE SOIC D 14 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2274
TLC2274Y PREVIEW DIESALE Y 0 TBD Call TI Call TI
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
PACKAGE OPTION ADDENDUM
www.ti.com 25-Sep-2013
Addendum-Page 10
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TLC2272, TLC2272A, TLC2272AM, TLC2272M, TLC2274, TLC2274A, TLC2274AM, TLC2274M :
Catalog: TLC2272A, TLC2272, TLC2274A, TLC2274
Automotive: TLC2272-Q1, TLC2272A-Q1, TLC2272A-Q1, TLC2272-Q1, TLC2274-Q1, TLC2274A-Q1, TLC2274A-Q1, TLC2274-Q1
Enhanced Product: TLC2272A-EP, TLC2272A-EP, TLC2274-EP, TLC2274A-EP, TLC2274A-EP, TLC2274-EP
Military: TLC2272M, TLC2272AM, TLC2274M, TLC2274AM
NOTE: Qualified Version Definitions:
Catalog - TI's standard catalog product
Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
Enhanced Product - Supports Defense, Aerospace and Medical Applications
PACKAGE OPTION ADDENDUM
www.ti.com 25-Sep-2013
Addendum-Page 11
Military - QML certified for Military and Defense Applications
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
5962-9555201NXDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
TLC2272ACDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
TLC2272ACPWR TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.0 Q1
TLC2272AIDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
TLC2272AMDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
TLC2272AMDRG4 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
TLC2272CDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
TLC2272CPWR TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.0 Q1
TLC2272IDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
TLC2272IPWR TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.0 Q1
TLC2272MDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
TLC2274ACDR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1
TLC2274ACPWR TSSOP PW 14 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1
TLC2274AIDR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1
TLC2274AIPWR TSSOP PW 14 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1
TLC2274AQDR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1
TLC2274CDR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1
TLC2274CNSR SO NS 14 2000 330.0 16.4 8.2 10.5 2.5 12.0 16.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 8-Jul-2013
Pack Materials-Page 1
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
TLC2274CPWR TSSOP PW 14 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1
TLC2274IDR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1
TLC2274IPWR TSSOP PW 14 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1
TLC2274MDR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1
TLC2274MDRG4 SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1
TLC2274QDRG4 SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
5962-9555201NXDR SOIC D 8 2500 367.0 367.0 35.0
TLC2272ACDR SOIC D 8 2500 340.5 338.1 20.6
TLC2272ACPWR TSSOP PW 8 2000 367.0 367.0 35.0
TLC2272AIDR SOIC D 8 2500 340.5 338.1 20.6
TLC2272AMDR SOIC D 8 2500 367.0 367.0 35.0
TLC2272AMDRG4 SOIC D 8 2500 367.0 367.0 35.0
TLC2272CDR SOIC D 8 2500 340.5 338.1 20.6
TLC2272CPWR TSSOP PW 8 2000 367.0 367.0 35.0
TLC2272IDR SOIC D 8 2500 340.5 338.1 20.6
TLC2272IPWR TSSOP PW 8 2000 367.0 367.0 35.0
TLC2272MDR SOIC D 8 2500 367.0 367.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 8-Jul-2013
Pack Materials-Page 2
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
TLC2274ACDR SOIC D 14 2500 333.2 345.9 28.6
TLC2274ACPWR TSSOP PW 14 2000 367.0 367.0 35.0
TLC2274AIDR SOIC D 14 2500 333.2 345.9 28.6
TLC2274AIPWR TSSOP PW 14 2000 367.0 367.0 35.0
TLC2274AQDR SOIC D 14 2500 367.0 367.0 38.0
TLC2274CDR SOIC D 14 2500 333.2 345.9 28.6
TLC2274CNSR SO NS 14 2000 367.0 367.0 38.0
TLC2274CPWR TSSOP PW 14 2000 367.0 367.0 35.0
TLC2274IDR SOIC D 14 2500 333.2 345.9 28.6
TLC2274IPWR TSSOP PW 14 2000 367.0 367.0 35.0
TLC2274MDR SOIC D 14 2500 367.0 367.0 38.0
TLC2274MDRG4 SOIC D 14 2500 367.0 367.0 38.0
TLC2274QDRG4 SOIC D 14 2500 367.0 367.0 38.0
PACKAGE MATERIALS INFORMATION
www.ti.com 8-Jul-2013
Pack Materials-Page 3
MECHANICAL DATA
MCER001A – JANUARY 1995 – REVISED JANUAR Y 1997
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
JG (R-GDIP-T8) CERAMIC DUAL-IN-LINE
0.310 (7,87)
0.290 (7,37)
0.014 (0,36)
0.008 (0,20)
Seating Plane
4040107/C 08/96
5
4
0.065 (1,65)
0.045 (1,14)
8
1
0.020 (0,51) MIN
0.400 (10,16)
0.355 (9,00)
0.015 (0,38)
0.023 (0,58)
0.063 (1,60)
0.015 (0,38)
0.200 (5,08) MAX
0.130 (3,30) MIN
0.245 (6,22)
0.280 (7,11)
0.100 (2,54)
0°–15°
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. This package can be hermetically sealed with a ceramic lid using glass frit.
D. Index point is provided on cap for terminal identification.
E. Falls within MIL STD 1835 GDIP1-T8
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated