Low Drop Voltage Regulator TLE 4276 Features * * * * * * * * * * * 5 V, 8.5 V, 10 V or variable output voltage Output voltage tolerance 4% 400 mA current capability Low-drop voltage Inhibit input Very low current consumption Short-circuit-proof Reverse polarity proof Suitable for use in automotive electronics Green Product (RoHS compliant) AEC Qualified P-TO220-5-43 P-TO220-5-3 P-TO220-5-122 P-TO252-5-11 Type Package Type Package TLE 4276 V50 PG-TO220-5-11 TLE 4276 GV50 PG-TO263-5-1 TLE 4276 V85 PG-TO220-5-11 TLE 4276 GV85 PG-TO263-5-1 TLE 4276 V10 PG-TO220-5-11 TLE 4276 GV10 PG-TO263-5-1 TLE 4276 V PG-TO220-5-11 TLE 4276 GV PG-TO263-5-1 TLE 4276 SV50 PG-TO220-5-12 TLE 4276 DV50 PG-TO252-5-11 TLE 4276 SV85 PG-TO220-5-12 TLE 4276 DV PG-TO252-5-11 TLE 4276 SV PG-TO220-5-12 Data Sheet 1 Rev. 2.6, 2007-03-20 TLE 4276 Functional Description The TLE 4276 is a low-drop voltage regulator in a TO package. The IC regulates an input voltage up to 40 V to VQ,nom = 5.0 V (V50), 8.5 V (V85), 10 V (V10) and adjustable voltage (V). The maximum output current is 400 mA. The IC can be switched off via the inhibit input, which causes the current consumption to drop below 10 A. The IC is short-circuitproof and includes temperature protection which turns off the device at overtemperature. Dimensioning Information on External Components The input capacitor CI is necessary for compensation of line influences. Using a resistor of approx. 1 in series with CI, the oscillating of input inductivity and input capacitance can be damped. The output capacitor CQ is necessary for the stability of the regulation circuit. Stability is guaranteed at values CQ 22 F and an ESR of 3 within the operating temperature range. Circuit Description The control amplifier compares a reference voltage to a voltage that is proportional to the output voltage and drives the base of the series transistor via a buffer. Saturation control as a function of the load current prevents any oversaturation of the power element. The IC also incorporates a number of internal circuits for protection against: * * * Overload Overtemperature Reverse polarity Data Sheet 2 Rev. 2.6, 2007-03-20 TLE 4276 PG-TO220-5-11 PG-TO220-5-12 PG-TO263-5-1 PG-TO252-5-11 GND 1 5 1 5 5 1 5 1 GND INH Q N.C. (VA) Q INH N.C. (VA) AEP02560 AEP02043 Q GND INH N.C. (VA) AEP02041 GND INH Q N.C. (VA) AEP02042 Figure 1 Pin Configuration (top view) Table 1 Pin Definitions and Functions Pin No. Symbol Function 1 I Input; block to ground directly at the IC with a ceramic capacitor. 2 INH Inhibit; low-active input. 3 GND Ground 4 N.C. VA Not connected for V50, V85, V10 Voltage Adjust Input; only for adjustable version. Connect an external voltage divider to determine the output voltage. 5 Q Output; block to GND with a 22 F capacitor, ESR 3 at 10 kHz Heatsink Data Sheet Connect to GND. 3 Rev. 2.6, 2007-03-20 TLE 4276 Saturation Control and Protection Circuit Temperature Sensor 1 6 Control Amplifier Q Buffer Bandgap Reference *) **) 2 4 3 INH VA GND *) For fixed Voltage Regulator only **) For adjustable Voltage Regulator only Figure 2 Data Sheet AEB02044 Block Diagram 4 Rev. 2.6, 2007-03-20 TLE 4276 Table 2 Absolute Maximum Ratings Parameter Symbol Limit Values Unit Test Condition Min. Max. VI II -42 45 V - - - - Internally limited VINH -42 45 V - VVA -0.3 10 V - VQ IQ -1.0 40 V - - - - Internally limited IGND - 100 mA - Tj Tstg -40 150 C - -50 150 C - Input I Voltage Current Inhibit INH Voltage Voltage Adjust Input VA Voltage Output Q Voltage Current Ground GND Current Temperature Junction temperature Storage temperature Note: Maximum ratings are absolute ratings; exceeding any one of these values may cause irreversible damage to the integrated circuit. Table 3 ESD Rating Parameter Symbol Limit Values Min. ESD Capability Data Sheet Unit Notes V Human Body Model Max. VESD,HBM 2000 - 5 Rev. 2.6, 2007-03-20 TLE 4276 Table 4 Operating Range Parameter Symbol Limit Values Min. Max. Unit Remarks Input voltage VI VQ + 0.5 40 V Fixed voltage devices V50, V85, V10 Input voltage VQ + 0.5 40 V Variable device V Input voltage VI VI 4.5 V 40 V Variable device V, VQ < 4 V Junction temperature Tj -40 150 C - Rthj-a Rthj-a Rthj-c - 65 K/W TO220 - 80 K/W TO252, TO2631) 4 K/W - Thermal Resistance Junction ambient Junction ambient Junction case - 1) Package mounted on PCB 80 x 80 x 1.5mm ; 35 Cu; 5 Sn; Footprint only; zero airflow. 3 Data Sheet 6 Rev. 2.6, 2007-03-20 TLE 4276 Table 5 Characteristics VI = 13.5 V; -40 C < Tj < 150 C (unless otherwise specified) Parameter Symbol Unit Measuring Condition Min. Typ. Max. Output voltage VQ 4.8 5.0 5.2 V 1 V50-Version 5 mA < IQ < 400 mA 6 V < VI < 28 V Output voltage VQ 4.8 5.0 5.2 V 1 V50-Version 5 mA < IQ < 200 mA 6 V < VI < 40 V Output voltage VQ 8.16 8.50 8.84 V V85-Version 1 5 mA < IQ < 400 mA 9.5 V < VI < 28 V Output voltage VQ 8.16 8.50 8.84 V 1 V85-Version 5 mA < IQ < 200 mA 9.5 V < VI < 40 V Output voltage VQ 9.6 10.0 10.4 V 1 V10-Version 5 mA < IQ < 400 mA 11 V < VI < 28 V Output voltage VQ 9.6 10.0 10.4 V V10-Version 1 5 mA < IQ < 200 mA 11 V < VI < 40 V Output voltage tolerance VQ -4 - 4 % 1 V-Version R2 < 50 k VQ + 1 V VI 40 V VI > 4.5 V 5 mA IQ 400 mA Output current limitation1) IQ 400 600 1100 mA Current consumption; Iq = II - IQ Iq - - 10 Current consumption; Iq = II - IQ Iq - 100 Current consumption; Iq = II - IQ Iq - 5 Data Sheet Limit Values Measuring Circuit - 1 A VINH = 0 V; Tj 100 C 1 220 A IQ = 1 mA 1 10 mA IQ = 250 mA 1 7 Rev. 2.6, 2007-03-20 TLE 4276 Table 5 Characteristics (cont'd) VI = 13.5 V; -40 C < Tj < 150 C (unless otherwise specified) Parameter Symbol Limit Values Unit Measuring Condition Measuring Circuit Min. Typ. Max. Current consumption; Iq = II - IQ Iq - 15 25 mA IQ = 400 mA 1 Drop voltage1) VDR - 250 500 mV V50, V85, V10 IQ = 250 mA VDR = VI - VQ 1 Drop voltage1) VDR - 250 500 mV variable devices IQ = 250 mA VI > 4.5 V VDR = VI - VQ 1 Load regulation VQ,Lo - 5 35 mV Line regulation VQ,Li - 15 25 mV Power supply ripple rejection PSRR - 54 - dB IQ = 5 mA to 400 mA 1 Vl = 12 V to 32 V 1 IQ = 5 mA fr = 100 Hz; 1 Vr = 0.5 Vpp Temperature output voltage drift dVQ/dT - 0.5 - - - mV/K Inhibit on voltage VINH - 2 3.5 V VQ 4.9 V 1 Inhibit off voltage VINH 0.5 1.7 - V VQ 0.1 V 1 Input current IINH 5 10 20 A VINH = 5 V 1 Inhibit 1) Measured when the output voltage VQ has dropped 100 mV from the nominal value obtained at VI = 13.5 V. Data Sheet 8 Rev. 2.6, 2007-03-20 TLE 4276 II Input 100 F IQ 5 Q I 1 Output CQ 100 nF 22 F TLE 4276 IINH VI INH 2 3 VINH *) Optional 4 GND R 1*) VQ *) VA Voltage Adjust R 2*) for adjustable Voltage Regulator Figure 3 RL AES02045 Measuring Circuit I 1 Input CI e.g. KL 15 2 4 3 GND *) Optional Figure 4 Data Sheet CQ TLE 4276 INH Output 5 Q for adjustable Voltage Regulator R 1*) *) VA Voltage Adjust R 2*) AES02046 Application Circuit 9 Rev. 2.6, 2007-03-20 TLE 4276 Application Information for Variable Output Regulator TLE 4276 V, SV, DV, GV The output voltage of the TLE 4276 V can be adjusted between 2.5 V and 20 V by an external output voltage divider, closing the control loop to the voltage adjust pin VA. The voltage at pin VA is compared to the internal reference of typical 2.5 V in an error amplifier. It controls the output voltage. 5 Q Internal Reference 2.5 V Typical Current and Saturation Control Vref R1 CQ 22 F 4 VA R2 AEB02804 Figure 5 Application Detail External Components at Output for Variable Voltage Regulator The output voltage is calculated according to Equation (1): VQ = (R1 + R2)/R2 x Vref, neglecting IVA (1) Vref is typically 2.5 V. To avoid errors caused by leakage current IVA, we recommend to choose the resistor value R2 according to Equation (2): R2 < 50 k (2) For a 2.5 V output voltage the output pin Q is directly connected to the adjust pin VA. The accuracy of the resistors R1 and R2 add an additional error to the output voltage tolerance. The operation range of the variable TLE 4276 V is VQ + 0.5 V to 40 V. For internal biasing a minimum input voltage of 4.3 V is required. For output voltages below 4 V the voltage drop is 4.3 V - VQ Data Sheet 10 Rev. 2.6, 2007-03-20 TLE 4276 Typical Performance Characteristics (V50, V85 and V10): Voltage VDR versus Output Current IQ Max. Output Current IQ versus Input Voltage VI AED03017 600 mV VDR IQ AED03020 800 mA 500 600 T j = 125 C 400 T j = 25 C VQ = 0 V 300 400 200 T j = 25 C 200 100 0 0 100 200 0 300 mA 400 0 10 20 30 40 V 50 IQ VI Current Consumption Iq versus Output Current IQ (high load) Current Consumption Iq versus Output Current IQ (low load) AED03021 60 AED03022 0.6 Iq mA Iq mA 50 0.5 40 0.4 T j = 25 C VI = 13.5 V 0.3 30 T j = 25 C VI = 13.5 V 20 0.2 10 0.1 0 0 100 200 300 400 0 mA 600 10 20 30 40 mA 60 IQ IQ Data Sheet 0 11 Rev. 2.6, 2007-03-20 TLE 4276 Typical Performance Characteristics for V50: Output Voltage VQ versus Temperature Tj Current Consumption Iq versus Input Voltage VI AED03081 5.2 VQ AED01967 30 V q mA 5.1 20 VI = 13.5 V T j = 25 C R L = 20 5.0 10 4.9 4.8 -40 0 40 80 0 120 C 160 0 10 20 30 Tj Low Voltage Behavior High Voltage Behavior AED01968 6 VQ 50 V V V VQ 5 AED03082_4276 3.5 mA II 3.0 2.5 4 2.0 VI = VQ 1.5 3 T j = 25 C R L = 20 T j = 25 C R L = 6.8 k 1.0 2 0.5 1 0 0 0 2 4 6 -2 -50 8 V 10 Data Sheet -25 0 25 V 50 VI VI 12 Rev. 2.6, 2007-03-20 TLE 4276 Typical Performance Characteristics for V85: Output Voltage VQ versus Temperature Tj Current Consumption Iq versus Input Voltage VI AED03018 9.0 VQ AED03025 30 V Iq mA 25 VI = 13.5 V 8.5 20 T j = 25 C R L = 34 15 8.0 10 5 7.5 -40 0 40 80 0 120 C 160 0 10 20 30 40 V 50 Tj VI Low Voltage Behavior High Voltage Behavior AED01972 12 VQ AED03080_4276 3.5 mA II 3.0 V 10 VQ 2.5 8 2.0 V =VQ 1.5 6 T j = 25 C R L = 34 T j = 25 C R L = 10 k 1.0 4 0.5 2 0 0 Data Sheet 0 4 8 12 -2 -50 16 V 20 V -25 0 25 V 50 VI 13 Rev. 2.6, 2007-03-20 TLE 4276 Typical Performance Characteristics for V10: Output Voltage VQ versus Temperature Tj Current Consumption Iq versus Input Voltage VI AED03019 10.5 AED03023 30 VQ V Iq mA 25 VI = 13.5 V 10.0 20 T j = 25 C R L = 40 15 9.5 10 5 9.0 -40 0 40 80 0 120 C 160 0 10 20 30 40 V 50 Tj VI Low Voltage Behavior High Voltage Behavior AED03024 12 VQ V VQ 10 AED03079_4276 3.5 mA II 3.0 2.5 8 2.0 VI = VQ 1.5 6 T j = 25 C R L = 40 T j = 25 C R L = 12 k 1.0 4 0.5 2 0 0 0 4 8 12 -2 -50 16 V 20 0 25 V 50 VI VI Data Sheet -25 14 Rev. 2.6, 2007-03-20 TLE 4276 Package Outlines 10 0.2 A 9.9 0.2 3.7 0.3 10.2 0.3 9.25 0.2 0.05 2.4 C 0.5 0.1 0...0.15 5 x 0.8 0.1 4 x 1.7 1) 1.6 0.3 1.27 0.1 8.6 0.3 0...0.3 4.4 2.8 0.2 1) 12.95 15.65 0.3 17 0.3 8.5 1) 3.7 -0.15 3.9 0.4 0.25 M A C 8.4 0.4 Typical All metal surfaces tin plated, except area of cut. GPT09064 Figure 6 PG-TO220-5-11 (Plastic Transistor Single Outline) Green Product (RoHS compliant) To meet the world-wide customer requirements for environmentally friendly products and to be compliant with government regulations the device is available as a green product. Green products are RoHS-Compliant (i.e Pb-free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020). You can find all of our packages, sorts of packing and others in our Infineon Internet Page "Products": http://www.infineon.com/products. Dimensions in mm SMD = Surface Mounted Device Data Sheet 15 Rev. 2.6, 2007-03-20 TLE 4276 10 0.2 A 9.9 0.2 B 1) 13 0.5 C 0.05 2.4 0.5 0.1 0...0.15 2.4 5 x 0.8 0.1 4 x 1.7 1) 9.25 0.2 1.27 0.1 2.8 0.2 0...0.3 4.4 11 0.5 1) 12.95 15.65 0.3 17 0.3 8.5 3.7 -0.15 0.25 M A B C Typical Metal surface min. X = 7.25, Y = 12.3 All metal surfaces tin plated, except area of cut. GPT09065 Figure 7 PG-TO220-5-12 (Plastic Transistor Single Outline) Green Product (RoHS compliant) To meet the world-wide customer requirements for environmentally friendly products and to be compliant with government regulations the device is available as a green product. Green products are RoHS-Compliant (i.e Pb-free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020). You can find all of our packages, sorts of packing and others in our Infineon Internet Page "Products": http://www.infineon.com/products. Dimensions in mm SMD = Surface Mounted Device Data Sheet 16 Rev. 2.6, 2007-03-20 TLE 4276 4.4 10 0.2 1.27 0.1 A 8.5 1) B 0.05 3.6 0.3 0...0.15 5 x 0.8 0.1 1.5 +0.4 2.4 0.1 7.55 1) 9.25 0.2 (13.85) 1 0.3 0...0.3 0.5 0.1 4 x 1.7 0.25 1) M A B 8 MAX. 0.1 B Typical Metal surface min. X = 7.25, Y = 6.9 All metal surfaces tin plated, except area of cut. GPT09470 Figure 8 PG-TO263-5-1 (Plastic Transistor Single Outline) Green Product (RoHS compliant) To meet the world-wide customer requirements for environmentally friendly products and to be compliant with government regulations the device is available as a green product. Green products are RoHS-Compliant (i.e Pb-free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020). You can find all of our packages, sorts of packing and others in our Infineon Internet Page "Products": http://www.infineon.com/products. Dimensions in mm SMD = Surface Mounted Device Data Sheet 17 Rev. 2.6, 2007-03-20 TLE 4276 6.5 +0.15 -0.05 A 1) 2.3 +0.05 -0.10 B (5) 0.51 MIN. 0.15 MAX. per side 5 x 0.6 0.1 1.14 4.56 0.5 +0.08 -0.04 0.9 +0.20 -0.01 0...0.15 0.8 0.15 (4.24) 1 0.1 9.98 0.5 6.22 -0.2 5.7 MAX. 0.5 +0.08 -0.04 0.1 B 0.25 M A B 1) Includes mold flashes on each side. All metal surfaces tin plated, except area of cut. GPT09527 Figure 9 PG-TO252-5-11 (Plastic Transistor Single Outline) Green Product (RoHS compliant) To meet the world-wide customer requirements for environmentally friendly products and to be compliant with government regulations the device is available as a green product. Green products are RoHS-Compliant (i.e Pb-free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020). You can find all of our packages, sorts of packing and others in our Infineon Internet Page "Products": http://www.infineon.com/products. Dimensions in mm SMD = Surface Mounted Device Data Sheet 18 Rev. 2.6, 2007-03-20 TLE 4276 Revision History Version Date Rev. 2.5 2004-12-23 Added ESD capability information in table "Maximum Ratings". Rev. 2.6 2007-03-20 Initial version of RoHS-compliant derivate of TLE 4276 Page 1: AEC certified statement added Page 1 and Page 15: RoHS compliance statement and Green product feature added Page 1 and Page 15: Package changed to RoHS compliant version Legal Disclaimer updated Data Sheet Changes 19 Rev. 2.6, 2007-03-20 Edition 2007-03-20 Published by Infineon Technologies AG 81726 Munich, Germany (c) 2007 Infineon Technologies AG All Rights Reserved. Legal Disclaimer The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights of any third party. Information For further information on technology, delivery terms and conditions and prices, please contact the nearest Infineon Technologies Office (www.infineon.com). Warnings Due to technical requirements, components may contain dangerous substances. For information on the types in question, please contact the nearest Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered.