DAC7800 DAC7801 DAC7802 (R) Dual Monolithic CMOS 12-Bit Multiplying DIGITAL-TO-ANALOG CONVERTERS FEATURES APPLICATIONS TWO D/As IN A 0.3" WIDE PACKAGE SINGLE +5V SUPPLY HIGH SPEED DIGITAL INTERFACE: Serial--DAC7800 8 + 4-Bit Parallel--DAC7801 12-Bit Parallel--DAC7802 MONOTONIC OVER TEMPERATURE PROCESS CONTROL OUTPUTS ATE PIN ELECTRONICS LEVEL SETTING PROGRAMMABLE FILTERS PROGRAMMABLE GAIN CIRCUITS AUTO-CALIBRATION CIRCUITS LOW CROSSTALK: -94dB min FULLY SPECIFIED OVER -40OC TO +85OC DESCRIPTION 12 DAC7802 12-Bit Interface VREF A RFB A CSB 12-Bit MDAC DAC A VREF B AGND A RFB B A1 IOUT B UPD A0 WR CLR CS 12 12-Bit MDAC DAC B AGND B CS CLR DAC7800 Serial Interface UPD B Serial 12 DAC7801 8-Bit Interface 8 Bits + 4 Bits 8 DAC7801 has a 2-byte (8 + 4) double-buffered interface. Data is first loaded (level transferred) into the input registers in two steps for each D/A. Then both D/As are updated simultaneously. DAC7801 features an asynchronous CLEAR control. DAC7801 is packaged in a 24-pin 0.3" wide plastic DIP. CSA WR IOUT A CLK DAC7800 features a serial interface capable of clocking-in data at a rate of at least 10MHz. Serial data is clocked (edge triggered) MSB first into a 24-bit shift register and then latched into each D/A separately or simultaneously as required by the application. An asynchronous CLEAR control is provided for poweron reset or system calibration functions. It is packaged in a 16-pin 0.3" wide plastic DIP. DAC7802 has a single-buffered 12-bit data word interface. Parallel data is loaded (edge triggered) into the single D/A register for each D/A. DAC7802 is packaged in a 24-pin 0.3" wide plastic DIP. UPD A The DAC7800, DAC7801 and DAC7802 are members of a new family of monolithic dual 12-bit CMOS multiplying digital-to-analog converters. The digital interface speed and the AC multiplying performance are achieved by using an advanced CMOS process optimized for data conversion circuits. High stability on-chip resistors provide true 12-bit integral and differential linearity over the wide industrial temperature range of -40oC to +85oC. International Airport Industrial Park * Mailing Address: PO Box 11400, Tucson, AZ 85734 * Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 * Tel: (520) 746-1111 * Twx: 910-952-1111 Internet: http://www.burr-brown.com/ * FAXLine: (800) 548-6133 (US/Canada Only) * Cable: BBRCORP * Telex: 066-6491 * FAX: (520) 889-1510 * Immediate Product Info: (800) 548-6132 (R) (c) 1990 Burr-Brown Corporation PDS-1079G 1 Printed in U.S.A. January, 1998 DAC7800, 01, 02 SPECIFICATIONS ELECTRICAL At VDD = +5VDC, VREF A = VREF B = +10V, TA = -40C to +85C, unless otherwise noted. DAC7800, 7801, 7802K PARAMETER CONDITIONS ACCURACY Resolution Relative Accuracy Differential Nonlinearity Gain Error MIN TYP MAX TA = +25C TA = -40C to +85C REFERENCE INPUT Input Resistance Input Resistance Match 6 2 0.005 3 5 10 150 10 0.5 14 3 0.8 0.8 1 10 10 UNITS 1/2 1 Bits LSB LSB LSB ppm/C nA nA 2 k % V V A A pF V mA %/% 2 TA = +25C TA = -40C to +85C CIN (Input Capacitance) POWER SUPPLY VDD IDD Power Supply Rejection MAX 1 1 3 Measured Using RFB A and RFB B. All Registers Loaded with All 1s. DIGITAL INPUTS VIH (Input High Voltage) VIL (Input Low Voltage) IIN (Input Current) TYP 12 Gain Temperature Coefficient(1) Output Leakage Current DAC7800, 7801, 7802L MIN 4.5 0.2 VDD from 4.5V to 5.5V 5.5 2 0.002 Same specification as for DAC7800, 7801, 7802K. AC PERFORMANCE OUTPUT OP AMP IS OPA602. At VDD = +5VDC, VREF A = VREF B = +10V, TA = +25C, unless otherwise noted. These specifications are fully characterized but not subject to test. DAC7800, 7801, 7802K PARAMETER CONDITIONS TYP MAX OUTPUT CURRENT SETTLING TIME To 0.01% of Full Scale RL = 100, CL = 13pF 0.4 0.8 DIGITAL-TO-ANALOG GLITCH IMPULSE VREF A = VREF B = 0V RL = 100, CL = 13pF 0.9 fVREF = 10kHz -75 -72 dB DAC Loaded with All 0s DAC Loaded with All 1s 30 70 50 100 pF pF AC FEEDTHROUGH OUTPUT CAPACITANCE CHANNEL-TO-CHANNEL ISOLATION VREF A to IOUT B VREF B to IOUT A fVREF A = 10kHz VREF B = 0V, Both DACs Loaded with 1s fVREF B = 10kHz VREF A = 0V, Both DACs Loaded with 1s DIGITAL CROSSTALK MIN DAC7800, 7801, 7802L MIN TYP MAX UNITS s nV-s -90 -94 dB -90 -101 dB nV-s Full Scale Transition RL = 100, CL = 13pF 0.9 Same specification as for DAC7800, 7801, 7802K. NOTE: (1) Guaranteed but not tested. The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user's own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support devices and/or systems. (R) DAC7800, 01, 02 2 PACKAGE/ORDERING INFORMATION PACKAGE PACKAGE DRAWING NUMBER(1) RELATIVE ACCURACY GAIN ERROR DAC7800KP DAC7800LP DAC7800KU DAC7800LU 16-Pin PDIP 16-Pin PDIP 16-Lead SOIC 16-Lead SOIC 180 180 211 211 1LSB 1/2LSB 3LSB 1LSB DAC7801KP DAC7801LP DAC7801KU DAC7801LU 24-Pin DIP 24-Pin DIP 24-Lead SOIC 24-Lead SOIC 243 243 239 239 1LSB 1/2LSB 3LSB 1LSB DAC7802KP DAC7802LP DAC7802KU DAC7802LU 24-Pin DIP 24-Pin DIP 24-Lead SOIC 24- Lead SOIC 243-3 243-3 239 239 1LSB 1/2LSB 3LSB 1LSB PRODUCT NOTE: (1) For detailed drawing and dimension table, please see end of data sheet, or Appendix C of Burr-Brown IC Data Book. ABSOLUTE MAXIMUM RATINGS ELECTROSTATIC DISCHARGE SENSITIVITY At TA = +25C, unless otherwise noted. VDD to AGND ................................................................................. 0V, +7V VDD to DGND ................................................................................. 0V, +7V AGND to DGND .......................................................................... -0.3, VDD Digital Input to DGND ......................................................... -0.3, VDD + 0.3 VREF A, VREF B to AGND ..................................................................... 20V VREF A, VREF B to DGND ..................................................................... 20V IOUT A, IOUT B to AGND ................................................................. -0.3, VDD Storage Temperature Range ........................................... -55C to +125C Operating Temperature Range .......................................... -40C to +85C Lead Temperature (soldering, 10s) ................................................ +300C Junction Temperature ...................................................................... +175C Electrostatic discharge can cause damage ranging from performance degradation to complete device failure. Burr-Brown Corporation recommends that all integrated circuits be handled and stored using appropriate ESD protection methods. Digital Inputs: All digital inputs of the DAC780X family incorporate on-chip ESD protection circuitry. This protection is designed and has been tested to withstand five 2500V positive and negative discharges (100pF in series with 1500) applied to each digital input. Analog Pins: Each analog pin has been tested to Burr-Brown's analog ESD test consisting of five 1000V positive and negative discharges (100pF in series with 1500) applied to each pin. AGND, IOUT, and RFB show some sensitivity. Failure to observe ESD handling procedures could result in catastrophic device failure. (R) 3 DAC7800, 01, 02 DAC7800 BLOCK DIAGRAM PIN CONFIGURATION VDD 12 10 UPD B DAC B Register 15 I OUT B 12 16 AGND B 14 RFB B Bit 11 13 V REF B Bit 12 4 VREF A Bit 23 3 R FB A 2 I OUT A DAC A Register 1 AGND A 12 6 UPD A 12 Control Logic and Shift Register DAC7800 5 DAC B Bit 0 DAC A 12 8 7 Data In CLK CS 11 9 CLR DGND AGND A 1 16 AGND B I OUT A 2 15 IOUT B R FB A 3 14 R FB B 13 VREF B 12 VDD VREF A 4 DAC7800 Top View DIP CLK 5 UPD A 6 11 CLR Data In 7 10 UPD B CS 8 9 DGND LOGIC TRUTH TABLE CLK UPD A UPD B CS CLR X X X X X 0 1 0 X X X 1 0 0 X 1 0 0 0 0 0 X 1 1 1 1 X X X X = Don't care. FUNCTION All register contents set to 0's (asynchronous). No data transfer. Input data is clocked into input register (location Bit 23) and previous data shifts. Input register bits 23 (LSB)--12 (MSB) are loaded into DAC A. Input register bits 11 (LSB)--0 (MSB) are loaded into DAC B. Input register bits 23 (LSB)--12 (MSB) are loaded into DAC A, and input register bits 11 (LSB)--0 (MSB) are loaded into DAC B. means falling edge triggered. DATA INPUT FORMAT DAC7800 Digital Interface Block Diagram UPD B UPD A DAC B Register DAC A Register LSB MSB Bit 23 Bit 12 LSB MSB Bit 11 Bit 0 CLK Data In 24-Bit Shift Register DAC7800 Data Input Sequence CLK Data In Bit 0 Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 MSB DAC B Bit 7 Bit 8 Bit 9 Bit 10 Bit 11 Bit 12 Bit 13 Bit 14 Bit 15 Bit 16 Bit 17 Bit 18 Bit 19 Bit 20 LSB MSB DAC B DAC A (R) DAC7800, 01, 02 4 Bit 21 Bit 22 Bit 23 LSB DAC A DAC7800 (CONT) TIMING CHARACTERISTICS VDD = +5V, VREF A = VREF B = +10V, TA = -40C to +85C. t5 PARAMETER CLK MINIMUM t1 -- Data Setup Time t2 -- Data Hold Time t3 -- Chip Select to CLK, Update, Data Setup Time t4 -- Chip Select to CLK, Update, Data Hold Time t5 -- CLK Pulse Width t6 -- Clear Pulse Width t7 -- Update Pulse Width t8 -- CLK Edge to UPD A or UPD B 0V t1 15ns 15ns 15ns DATA 40ns CS 40ns 40ns 40ns 15ns UPD A UPD B 5V 0V t3 t2 5V t8 t7 t4 5V t6 5V CLR NOTES: (1) All input signal rise and fall times are measured from 10% to 90% of +5V. t R = t F = 5ns. (2) Timing measurement reference level is VIH + V IL . 2 DAC7801 BLOCK DIAGRAM PIN CONFIGURATION VDD 20 DAC7801 DAC A MS Input Reg AGND A 1 24 AGND B IOUT A 2 23 I OUT B RFB A 3 22 RFB B VREF A 4 21 V REF B CS 5 20 V DD 19 UPD DAC A LS Input Reg 4 8 DAC A Register A1 19 I OUT A DB0 6 1 AGND A DB1 7 18 WR R FB A DB2 8 17 16 CLR 4 V REF A DB3 9 16 A0 15 A1 CS 5 21 V REF B DB4 10 15 A0 WR 18 22 R FB B DB5 11 14 DB7 CLR 17 23 I OUT B DGND 12 13 DB6 24 AGND B DAC A 3 Control Logic UPD DAC B 12 DAC B Register 14 4 8 DAC B MS Input Reg DAC B LS Input Reg DAC7801 Top View DIP 2 12 12 6 DB7-DB0 DGND LOGIC TRUTH TABLE CLR UPD CS WR A1 A0 1 1 0 1 1 1 1 1 1 1 1 X 1 1 1 1 0 0 1 X X 0 0 0 0 1 0 X 1 X 0 0 0 0 0 0 X X X 0 0 1 1 X X X X X 0 1 0 1 X X FUNCTION No Data Transfer No Data Transfer All Registers Cleared DAC A LS Input Register Loaded with DB7-DB0 (LSB) DAC A MS Input Register Loaded with DB3 (MSB)-DB0 DAC B LS Input Register Loaded with DB7-DB0 (LSB) DAC B MS Input Register Loaded with DB3 (MSB)-DB0 DAC A, DAC B Registers Updated Simultaneously from Input Registers DAC A, DAC B Registers are Transparent X = Don't care. (R) 5 DAC7800, 01, 02 DAC7801 (CONT) TIMING CHARACTERISTICS VDD = +5V, VREF A = VREF B = +10V, TA = -40C to +85C. t1 PARAMETER MINIMUM t1 -- Address Valid to Write Setup Time t2 -- Address Valid to Write Hold Time t3 -- Data Setup Time t4 -- Data Hold Time t5 -- Chip Select or Update to Write Setup Time t6 -- Chip Select or Update to Write Hold Time t7 -- Write Pulse Width t8 -- Clear Pulse Width t2 5V 0V A0-A1 t3 10ns 10ns 30ns 10ns 0ns 0ns 40ns 40ns t4 5V 0V DATA t5 t6 5V 0V CS, UPD t7 5V 0V WR t8 5V 0V CLR NOTES: (1) All input signal rise and fall times are measured from 10% to 90% of +5V. t R = tF = 5ns. (2) Timing measurement reference level is VIH + V IL . 2 DAC7802 BLOCK DIAGRAM PIN CONFIGURATION VDD AGND 1 24 I OUT B 12 IOUT A 2 23 R FB B DAC A Register R FB A 3 22 V REF B V REF A 4 21 V DD CS A 5 20 CS B (LSB) DB0 6 19 WR DB1 7 18 DB11 (MSB) DB2 8 17 DB10 DB3 9 16 DB9 DB4 10 15 DB8 DB5 11 14 DB7 DGND 12 13 DB6 21 DAC7802 CK 12 CS A CS B DAC A 5 DAC B 20 12 WR 19 CK 2 IOUT A 3 R FB A 4 V REF A 22 V REF B 23 R FB B 24 I OUT B 1 AGND DAC B Register 12 12 DGND 18 DAC7802 Top View DIP 6 TIMING CHARACTERISTICS DB11-DB0 At VDD = +5V, and TA = -40oC to +85oC. LOGIC TRUTH TABLE CSA CSB WR X X 1 1 1 X No Data Transfer 0 A Rising Edge on CSA or CSB Loads Data to the Respective DAC t1 t2 t3 t4 t5 No Data Transfer 0 1 DAC A Register Loaded from Data Bus 1 0 DAC B Register Loaded from Data Bus 0 0 DAC A and DAC B Registers Loaded from Data Bus X = Don't care. PARAMETER FUNCTION - MINIMUM Data Setup Time Data Hold Time Chip Select to Write Setup Time Chip Select to Write Hold Time Write Pulse Width 20ns 15ns 30ns 0ns 30ns t1 t2 5V 0V DATA t3 t4 CSA, CSB t5 means rising edge triggered. 5V 5V WR NOTES: (1) All input signal rise and fall times are measured from 10% to 90% of +5V. t R = t F = 5ns. (2) Timing measurement reference level VIH + V IL . is 2 (R) DAC7800, 01, 02 6 TYPICAL PERFORMANCE CURVES OUTPUT OP AMP IS OPA602. TA = +25C, VDD = +5V. OUTPUT LEAKAGE CURRENT vs TEMPERATURE THD + NOISE vs FREQUENCY -60 -65 100n -70 THD + Noise (dB) Output Leakage Current (A) 1 10n 1n 100p -75 1Vrms -80 3Vrms -85 6Vrms -90 10p -95 1p -100 -75 -50 -25 0 +25 +50 +75 +100 +125 10 100 100k Frequency (Hz) CHANNEL-TO-CHANNEL ISOLATION vs FREQUENCY FEEDTHROUGH vs FREQUENCY -20 0 -30 -10 -40 -20 -50 -30 Feedthrough (dB) Crosstalk (dB) 10k 1k Temperature (C) -60 -70 -80 -90 -40 -50 -60 -70 -80 -100 -110 -90 -120 -100 1k 10k 1M 100k 10M 1k 10k 1M 100k Frequency (Hz) 10M Frequency (Hz) PSRR vs FREQUENCY FREQUENCY RESPONSE +30 70 CF = 0pF +20 CF = 5pF 60 +10 50 0 40 PSRR (dB) Gain (dB) DAC Loaded w/0s -10 CF = 10pF -20 30 20 -30 10 -40 0 DAC Loaded w/1s -10 -50 1k 10k 100k 1M 10M 1k 10k 100k 1M Frequency (Hz) Frequency (Hz) (R) 7 DAC7800, 01, 02 DISCUSSION OF SPECIFICATIONS of the ladder regardless of the input code. The input resistance at VREF is therefore constant and can be driven by either a voltage or current, AC or DC, positive or negative polarity, and have a voltage range up to 20V. RELATIVE ACCURACY This term, also known as end point linearity or integral linearity, describes the transfer function of analog output to digital input code. Relative accuracy describes the deviation from a straight line, after zero and full scale errors have been adjusted to zero. VREF A 2R DIFFERENTIAL NONLINEARITY Differential nonlinearity is the deviation from an ideal 1LSB change in the output when the input code changes by 1LSB. A differential nonlinearity specification of 1LSB maximum guarantees monotonicity. R R 2R 2R 2R 2R R RFB A IOUT A AGND DB11 (MSB) GAIN ERROR Gain error is the difference between the full-scale DAC output and the ideal value. The ideal full scale output value for the DAC780X is -(4095/4096)VREF . Gain error may be adjusted to zero using external trims as shown in Figures 5 and 7. DB10 DB9 DB0 (LSB) FIGURE 1. Simplified Circuit Diagram for DAC A. A CMOS switch transistor, included in series with the ladder terminating resistor and in series with the feedback resistor, RFB A, compensates for the temperature drift of the ON resistance of the ladder switches. OUTPUT LEAKAGE CURRENT The current which appears at IOUT A and IOUT B with the DAC loaded with all zeros. Figure 2 shows an equivalent circuit for DAC A. COUT is the output capacitance due to the N-channel switches and varies from about 30pF to 70pF with digital input code. The current source ILKG is the combination of surface and junction leakages to the substrate. ILKG approximately doubles every 10C. RO is the equivalent output resistance of the D/A and it varies with input code. OUTPUT CAPACITANCE The parasitic capacitance measured from IOUT A or IOUT B to AGND. CHANNEL-TO-CHANNEL ISOLATION The AC output error due to capacitive coupling from DAC A to DAC B or DAC B to DAC A. R RFB A VREF A MULTIPLYING FEEDTHROUGH ERROR The AC output error due to capacitive coupling from VREF to IOUT with the DAC loaded with all zeros. R DIN VREF x 4096 R RO ILKG IOUT A COUT AGND A OUTPUT CURRENT SETTLING TIME The time required for the output current to settle to within +0.01% of final value for a full scale step. FIGURE 2. Equivalent Circuit for DAC A. INSTALLATION DIGITAL-TO-ANALOG GLITCH ENERGY The integrated area of the glitch pulse measured in nanovoltseconds. The key contributor to digital-to-analog glitch is charge injected by digital logic switching transients. ESD PROTECTION All digital inputs of the DAC780X incorporate on-chip ESD protection circuitry. This protection is designed to withstand 2.5kV (using the Human Body Model, 100pF and 1500). However, industry standard ESD protection methods should be used when handling or storing these components. When not in use, devices should be stored in conductive foam or rails. The foam or rails should be discharged to the destination socket potential before devices are removed. DIGITAL CROSSTALK Glitch impulse measured at the output of one DAC but caused by a full scale transition on the other DAC. The integrated area of the glitch pulse is measured in nanovoltseconds. POWER SUPPLY CONNECTIONS The DAC780X are designed to operate on VDD = +5V +10%. For optimum performance and noise rejection, power supply decoupling capacitors CD should be added as shown in the application circuits. These capacitors (1F tantalum recommended) should be located close to the D/A. AGND and CIRCUIT DESCRIPTION Figure 1 shows a simplified schematic of one half of a DAC780X. The current from the VREF A pin is switched between IOUT A and AGND by 12 single-pole double-throw CMOS switches. This maintains a constant current in each leg (R) DAC7800, 01, 02 R 8 DGND should be connected together at one point only, preferably at the power supply ground point. Separate returns minimize current flow in low-level signal paths if properly connected. Output op amp analog common (+ input) should be connected as near to the AGND pins of the DAC780X as possible. DATA INPUT ANALOG OUTPUT MSB LSB 1111 1111 1111 1000 0000 0000 0000 0000 0001 0000 0000 0000 -VREF (4095/4096) -VREF (2048/4096) = -1/2VREF -VREF (1/4096) 0 Volts TABLE II. Unipolar Output Code. WIRING PRECAUTIONS To minimize AC feedthrough when designing a PC board, care should be taken to minimize capacitive coupling between the VREF lines and the IOUT lines. Similarly, capacitive coupling between DACs may compromise the channel-tochannel isolation. Coupling from any of the digital control or data lines might degrade the glitch and digital crosstalk performance. Solder the DAC780X directly into the PC board without a socket. Sockets add parasitic capacitance (which can degrade AC performance). VDD VREF A +5V CD 1F + RFB A IOUT A DAC A DAC780X AMPLIFIER OFFSET VOLTAGE The output amplifier used with the DAC780X should have low input offset voltage to preserve the transfer function linearity. The voltage output of the amplifier has an error component which is the offset voltage of the op amp multiplied by the "noise gain" of the circuit. This "noise gain" is equal to (RF / RO + 1) where RO is the output impedance of the D/A IOUT terminal and RF is the feedback network impedance. The nonlinearity occurs due to the output impedance varying with code. If the 0 code case is excluded (where RO = infinity), the RO will vary from R to 3R providing a "noise gain" variation between 4/3 and 2. In addition, the variation of RO is nonlinear with code, and the largest steps in RO occur at major code transitions where the worst differential nonlinearity is also likely to be experienced. The nonlinearity seen at the amplifier output is 2VOS - 4VOS /3 = 2VOS/3. Thus, to maintain good nonlinearity the op amp offset should be much less than 1/2LSB. AGND A - A1 + VOUT A - A2 + VOUT B RFB B IOUT B DAC B DGND C1 10pF VREF B C2 10pF AGND B A1, A2 OPA602 or 1/2 OPA2107. DAC7802 has a single analog common, AGND. FIGURE 3. Unipolar Configuration. VDD +5V CD 1F + VIN A R1 100 V REF A RFB A R2 IOUT A DAC A UNIPOLAR CONFIGURATION Figure 3 shows DAC780X in a typical unipolar (two-quadrant) multiplying configuration. The analog output values versus digital input code are listed in Table II. The operational amplifiers used in this circuit can be single amplifiers such as the OPA602, or a dual amplifier such as the OPA2107. C1 and C2 provide phase compensation to minimize settling time and overshoot when using a high speed operational amplifier. If an application requires the D/A to have zero gain error, the circuit shown in Figure 4 may be used. Resistors R2 and R4 induce a positive gain error greater than worst-case initial negative gain error. Trim resistors R1 and R3 provide a variable negative gain error and have sufficient trim range to correct for the worst-case initial positive gain error plus the error produced by R2 and R4. AGND A C1 10pF - A1 + VOUT A RFB B R4 DAC780X IOUT B DAC B V REF B DGND 47 R3 100 47 AGND B C2 10pF - A2 + VOUT B A1, A2 OPA602 or 1/2 OPA2107. DAC7802 has a single analog common, AGND. V IN B FIGURE 4. Unipolar Configuration with Gain Trim. The operational amplifiers used in this circuit can be single amplifiers such as the OPA602, a dual amplifier such as the OPA2107, or a quad amplifier like the OPA404. C1 and C2 provide phase compensation to minimize settling time and overshoot when using a high speed operational amplifier. The bipolar offset resistors R5-R7 and R8-R10 should be ratio-matched to 0.01% to ensure the specified gain error performance. BIPOLAR CONFIGURATION Figure 5 shows the DAC780X in a typical bipolar (fourquadrant) multiplying configuration. The analog output values versus digital input code are listed in Table III. (R) 9 DAC7800, 01, 02 If an application requires the D/A to have zero gain error, the circuit shown in Figure 6 may be used. Resistors R2 and R4 induce a positive gain error greater than worst-case initial negative gain error. Trim resistors R1 and R3 provide a variable negative gain error and have sufficient trim range to correct for the worst-case initial positive gain error plus the error produced by R2 and R4. DATA INPUT ANALOG OUTPUT MSB LSB 1111 1111 1111 1000 0000 0001 1000 0000 0000 0111 1111 1111 0000 0000 0000 +VREF (2047/2048) +VREF (1/2048) 0 Volts -VREF (1/2048) -VREF (2048/2048) TABLE III. Bipolar Output Code. R1 20k +5V VDD VREF A R2 20k - CD + 1F A2 R3 10k VOUT A + RFB A C1 10pF IOUT A DAC A - A1 AGND A + DAC7802 has a single analog common, AGND. A1-A4, OPA602 or 1/2 OPA2107. DAC780X RFB B C2 10pF IOUT B DAC B AGND B - A3 + R5 10k R6 20k R4 20k - DGND A4 VOUT B + VREF B FIGURE 5. Bipolar Configuration. APPLICATIONS 12-BIT PLUS SIGN DACS For a bipolar DAC with 13 bits of resolution, two solutions are possible. As shown in Figure 7, the addition of a precision difference amplifier and a high speed JFET switch provides a 12-bit plus sign voltage-output DAC. When the switch selects the op amp output, the difference amplifier serves as a non-inverting output buffer. If the analog ground side of the switch is selected, the output of the difference amplifier is inverted. DAC1 and DAC2 can be updated in parallel with a single word to set the center frequency of the filter. DAC 4, which makes use of the uncommitted op amp in UAF42, sets the Q of the filter. DAC3 sets the gain of the filter transfer function without changing the Q of the filter. The reverse is also true. The center frequency is determined by fC = 1/2RC where R is the ladder resistance of the D/A (typical value, 10k) and C the internal capacitor value (1000pF) of the UAF42. External capacitors can be added to lower the center frequency of the filter. But the highest center frequency for this circuit will be about 16kHz because the effective series resistance of the D/A cannot be less than 10k. Another option, shown in Figure 8, also produces a 12-bit plus sign output without the additional switch and digital control line. DIGITALLY PROGRAMMABLE ACTIVE FILTER DAC780X are shown in Figure 9 in a digitally programmable active filter application. The design is based on the statevariable filter, Burr-Brown UAF42, an active filter topology that offers stable and repeatable filter characteristics. Note that the ladder resistance of the D/A may vary from device to device. Thus, for best tracking, DAC2 and DAC3 should be in the same package. Some calibration may be necessary from one filter to another. (R) DAC7800, 01, 02 10 R5 20k +5V VDD VIN A R6 20k - CD + 1F + VREF A RFB A R7 10k R2 47 C1 10pF IOUT A DAC A RFB B + DAC7802 has a single analog common, AGND. A1-A4, OPA602 or 1/2 OPA2107. R4 47 C2 10pF IOUT B DAC B - A1 AGND A DAC7802 AGND B - A3 + R9 10k 10k R8 20k VREF B R3 100 DGND VOUT A A2 R1 100 R10 20k - VOUT B A4 + VIN B FIGURE 6. Bipolar Configuration with Gain Trim. +15V 2 +10V 6 REF102 +5V 4 VDD CD 1F VREF A RFB A IOUT A DAC A AGND A C1 10pF R A1 R 2 DAC780X 6 R 10V 13 Bits 3 R Sign Control DAC B DGND VREF B DG188 AGND B 1 INA105 DAC7802 has a single analog common, AGND. A1 OPA602 or 1/2 OPA2107. FIGURE 7. 12-Bit Plus Sign DAC. (R) 11 DAC7800, 01, 02 +15V 2 +10V 6 REF102 +5V 4 VDD CD 1F VREF A RFB A C1 10pF IOUT A DAC A R A1 AGND A R 2 DAC780X R INA105 A2 AGND B VREF B DGND 10V 13 Bits 3 C2 10pF IOUT B DAC B 6 R RFB B 1 DAC7802 has a single analog common, AGND. A1 OPA602 or 1/2 OPA2107. FIGURE 8. 13-Bit Bipolar DAC. Q Adjust VREF 2 DAC 2 f C Adjust V REF 4 IOUT 2 DAC 4 AGND 2 VREF 1 I OUT 4 AGND 4 1/2 DAC780X IOUT 1 DAC 1 R FB 4 AGND 1 DAC780X High-Pass Out Filter Input 13 R Low-Pass Out Band-Pass Out 8 7 1 14 5 VREF 3 I OUT 3 DAC 3 C R C 12 AGND 3 1/2 DAC780X Gain Adjust 6 3 R R UAF 42 R = 50k 0.5% C = 1000pF 0.5% 11 2 FIGURE 9. Digitally Programmable Universal Active Filter. (R) DAC7800, 01, 02 12 4