NEW Hall Effect Rotary Position Sensor Series HRS100 The unique, new HRS-100 Hall Effect Rotary Position Sensor addresses a variety of marine, automotive, industrial truck and aircraft position sensing and control applications requiring precision, ultra long-life, cost-effective solutions in harsh environments -- grime, extreme temperature, vibration (dither) or moisture. Tight linearity of 2% or less and rugged 10 million cycle life plus programmable temperature coefficient, offset and gain control at the time of manufacture provide customization not previously available. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MECHANICAL Housing: .598 .015 Depth F.M.S. x 1.094 .015 diameter. Stainless steel can. Bushing: 3/8-32, .375 Max Length F.M.S. Excludes C-RING.* Shaft: .249 .001 diameter, Flatted, Slotted, Lengths to 1.5 inches* AR lugs: 2 at 180 degrees, on .531 radius, .125W x .128 F.M.S. 1 lug optional* Output current: 2 ma max. (source or sink) Over voltage protection: 18 VDC Max. Reverse voltage protection: -14.5 VDC Max. Supply voltage: 5 VDC 10% Supply current: 5 ma. typical Load Life: Greater than 10,000 Hrs. at rated load ESD sensitivity: 7KV max. (Human body model). Standard electronic assembly practices should be observed. 30 V/m, 10Khz to 1000Mhz at 3 meters Terminal Style: Solder lugs or wire leads Mechanical angle: 45, 60, 80, 90 degrees 2 degrees 180 degrees, optional* EMI Rotational Life: 10M min. ENVIRONMENTAL Rotational Torque 2.0 in oz max. at 25 degrees C with shaft seal Low temperature operation: -40 degrees C Stop Torque: 5 inch pounds Push out: 20 pounds min. High temperature operation: +85 degrees C Pull out: 10 pounds min. Storage temperature: +105 degrees C Max. Shock: 50 Gs, 11 ms Vibration: 15Gs, 10 to 2000 Hz ELECTRICAL Electrical Angle: 45, 60, 80, 90 degrees 2 degrees 180 degrees, optional* Electrical Output Range: 0% - 100%, 5% - 45%, 5% - 95%, 10% - 90% of applied Vdd. Customer specific linear outputs available.* Linearity: *Consult the factory. Clarostat reserves the right to change the above specifications without notice. 2% (less than 1% typical) Telephone: 800.874.1874 Fax: 800.223.5138 12055 Rojas Drive * Suite K * El Paso, Texas USA 79936 * www.clarostat.com theNEW Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MARINE: Throttle position sensor Outboard motor Inboard/outboard (IO) based power systems Diesel engine, electronic injector control Control position sensor: Rudder position Trim tab and plain position Drive tilt and drive gimbal position Auto pilot feed back and controls Drive by wire systems, control and feedback AUTOMOTIVE: Foot pedal position sensor Throttle position sensor Steering position sensor Suspension system position sensors Seat position sensor Mirror position sensor FORKLIFT - INDUSTRIAL TRUCK - FARM EQUIPMENT: Throttle/speed control (Forward, Neutral, Reverse) Foot pedal position sensor Lift and shuttle position and control Tilt control and feedback of tilt position Implement gimbal position and control Steering position AIRCRAFT: Rudder, pitch-trim or aileron position Servo tab position Flap and slat position Flap asymmetry sensors/detection Elevator position Nose wheel position Throttle position Foot pedal position sensor Fly by wire feedback systems Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mounting Surface 1.094 Shaft Dimensions .080 .520 .375 SLOTTED SHAFT .063 +.015 -.005 .047 .005 FLATTED SHAFT .218 .002 .875 .375 .010 .112 1 GND. .128 Dimensions shown in inches How to Order . . . . . . . . . . . SHAFT END BUSHING LENGTH HRS100 N MOISTURE SEAL Y: Yes N: No N 32 SHAFT LENGTH 1/64" increments, measured from mounting surface, 1.5 inches max. P NOTE: Flat will extend to within .062 of bushing where shaft length will not permit standard flat. When ordering, indicate the desired options as shown in this example ROTATION P: Plain round S: Slotted F: Flatted N: .375" G: .250" 3 Vdd OUTPUT 2 A: 45 B: 60 C: 80 S D: 90 E: 180 D TERMINALS S: Solder lug (90 from shaft) F: S bent 90 to front B: S bent 90 to back W: Cable wire length A LINEARITY A: 2% B: 1.5% C: 1% .245 .270 1.950 2.205 Vmin CCW end Vmax CCW end Vmin CW end Vmax CW end Specify output voltages at both ends, minimum and maximum values (Specify length, inches) C: Cable wire W/connector: (Specify cable length and connector) Telephone: 800.874.1874 Fax: 800.223.5138 12055 Rojas Drive * Suite K * El Paso, Texas USA 79936 * www.clarostat.com theNEW