MECHANICAL
Housing: .598 ±.015 Depth F.M.S. x 1.094
±.015 diameter. Stainless steel can.
Bushing: 3/8-32, .375 Max Length F.M.S.
Excludes C-RING.*
Shaft: .249 ±.001 diameter, Flatted,
Slotted, Lengths to 1.5 inches*
AR lugs: 2 at 180 degrees, on .531 radius,
.125W x .128 F.M.S. 1 lug optional*
Terminal Style: Solder lugs or wire leads
Mechanical angle: 45, 60, 80, 90 degrees ±2 degrees
180 degrees, optional*
Rotational Life: 10M min.
Rotational Torque 2.0 in oz max. at 25 degrees C with
shaft seal
Stop Torque: 5 inch pounds
Push out: 20 pounds min.
Pull out: 10 pounds min.
ELECTRICAL
Electrical Angle: 45, 60, 80, 90 degrees ±2 degrees
180 degrees, optional*
Electrical Output Range: 0% - 100%, 5% – 45%, 5% – 95%,
10% - 90% of applied Vdd. Customer
specific linear outputs available.*
Linearity: ± 2% (less than 1% typical)
Specifications ................................
The unique, new HRS-100 Hall Effect Rotary Position Sensor
addresses a variety of marine, automotive, industrial truck and
aircraft position sensing and control applications requiring
precision, ultra long-life, cost-effective solutions in harsh
environments -- grime, extreme temperature, vibration
(dither) or moisture. Tight linearity of 2% or less and rugged
10 million cycle life plus programmable temperature coeffi-
cient, offset and gain control at the time of manufacture pro-
vide customization not previously available.
theNEW
Telephone: 800.874.1874 Fax: 800.223.5138
12055 Rojas Drive • Suite K • El Paso, Texas USA 79936 • www.clarostat.com
Series HRS100
NEW
Output current: 2 ma max. (source or sink)
Over voltage protection: 18 VDC Max.
Reverse voltage
protection: -14.5 VDC Max.
Supply voltage: 5 VDC ± 10%
Supply current: 5 ma. typical
Load Life: Greater than 10,000 Hrs. at rated load
ESD sensitivity: ±7KV max. (Human body model).
Standard electronic assembly practices
should be observed.
EMI 30 V/m, 10Khz to 1000Mhz at 3 meters
ENVIRONMENTAL
Low temperature
operation: -40 degrees C
High temperature
operation: +85 degrees C
Storage temperature: +105 degrees C Max.
Shock: 50 Gs, 11 ms
Vibration: 15Gs, 10 to 2000 Hz
*Consult the factory.
Clarostat reserves the right to change the above specifications without notice.
Hall Effect Rotary Position Sensor
Shaft Dimensions
.128
.112
.520
.080
.375
Mounting Surface
Vdd
3
GND.
1
OUTPUT
2
1.094
.875
.063 +.015
-.005
.047 ±.005
SLOTTED SHAFT
.375 ±.010
FLATTED SHAFT .218 ± .002
NOTE: Flat will extend to within .062 of
bushing where shaft length will not
permit standard flat.
Dimensions shown in inches
theNEW
Telephone: 800.874.1874 Fax: 800.223.5138
12055 Rojas Drive • Suite K • El Paso, Texas USA 79936 • www.clarostat.com
Dimensions ..................................
Applications .................................
MARINE:
Throttle position sensor
Outboard motor
Inboard/outboard (IO) based power systems
Diesel engine, electronic injector control
Control position sensor:
Rudder position
Trim tab and plain position
Drive tilt and drive gimbal position
Auto pilot feed back and controls
Drive by wire systems, control and feedback
AUTOMOTIVE:
Foot pedal position sensor
Throttle position sensor
Steering position sensor
Suspension system position sensors
Seat position sensor
Mirror position sensor
FORKLIFT – INDUSTRIAL TRUCK – FARM
EQUIPMENT:
Throttle/speed control (Forward,
Neutral, Reverse)
Foot pedal position sensor
Lift and shuttle position and control
Tilt control and feedback of
tilt position
Implement gimbal position and control
Steering position
AIRCRAFT:
Rudder, pitch-trim or
aileron position
Servo tab position
Flap and slat position
Flap asymmetry
sensors/detection
Elevator position
Nose wheel position
Throttle position
Foot pedal position sensor
Fly by wire feedback systems
How to Order ........... When ordering, indicate the desired options as shown in this example
NN32 P S D A
HRS100
MOISTURE
SEAL
Y: Yes
N: No
Vmin
CW end
Vmax
CCW end Vmax
CW end
.245 1.950
SHAFT LENGTH
1/64” increments,
measured from
mounting surface,
1.5 inches max.
TERMINALS
S: Solder lug
(90º from shaft)
F: S bent 90º to front
B: S bent 90º to back
W: Cable wire length
(Specify length, inches)
C: Cable wire W/connector:
(Specify cable length
and connector)
LINEARITY
A: 2%
B: 1.5%
C: 1%
Vmin
CCW end
Specify output voltages at both ends, minimum
and maximum values
.270 2.205
BUSHING
LENGTH
N: .375”
G: .250”
SHAFT END
P: Plain round
S: Slotted
F: Flatted
ROTATION
A: 45º
B: 60º
C: 80º
D: 90º
E: 180º
