110 Watts
PD110 Series
Low Cost
•
100% Burn-In
•
Small Size, Light Weight
•
Three Wide Input Ranges
•
Over voltage Protection
•
Overcurrent Protection
•
••
Specification
All specifications typical at nominal line, full load and 25°C
Intelligent Design Quality Product
XPiQ inc.
DC/DC Conver ters
Input
Input Voltage • 10 to 20 VDC
(PD110 “L” series)
18 to 36 VDC
(PD110 “M” series)
36 to 72 VDC
(PD110 “H” series)
Input Current • 15A (rms) for 12 VDC
9.4A (rms) for 24 VDC
4.7A (rms) for 48 VDC
Output
Output Voltage/ • See rating chart
Current
Ripple • 1% peak to peak maximum
Overvoltage • Provided on output #1 only,
Protection set at 112-132% of its nominal
output voltage
Overcurrent • All outputs protected in short
Protection: circuit conditions
Temperature • All outputs ±0.04%/°C maximum
Coefficient:
General
Efficiency • 60% minimum
Hold-up time • 10 msec
Line Regulation • ±0.5% max.
Isolation Voltage • 1000 VDC from input to output
Environmental
Operating • 0°C to +70°C*
Temperature
Storage • -40°C to +85°C
Temperature
MTBF • 100,000 hours
Weight • 670 g without cover
* Derate linearly from 100% load to 50°C to 50% load at 70°C
PH: 508 429.9883
FAX: 800 226.2100
Email: sales@xp-iq.com
Holliston, MA 01746 USA
www.XP-iQ.com
53
PD110 13/11/02 3:25 pm Page 1
Model 1, 2, 3 4, 5 6, 7 8, 9 10 11 12 13
PD110-10, PD110-12 OUTPUT RETURN RETURN OUTPUT N.C. N.C. KEY N.C.
PD110-13, PD110-14 #1 #1
PD110-16
PD110-23 OUTPUT COMMON COMMON OUTPUT N.C. N.C. KEY N.C.
#1 RETURN RETURN #2
PD110-31, PD110-32 OUTPUT COMMON COMMON OUTPUT N.C. OUTPUT KEY N.C.
#1 RETURN RETURN #2 #3
PD110-40, PD110-41 OUTPUT COMMON COMMON OUTPUT N.C. OUTPUT KEY OUTPUT
PD110-42, PD110-45-1 #1 RETURN RETURN #2 #3 #4
PD110-45-2, PD110-46
Notes
•
Mechanical Details
Pin Char t
1. For output #2, minimum load is 0 A and peak current is shown for 10% maximum duty cycle for less than 60 seconds.
2. PD110 “M” & “H” series is suitable for 110 watts maximum at 20 CFM forced air cooling or 80 watts maximum at convection cooling.
3. PD110 “L” series is suitable for 90 watts maximum at 20 CFM forced air cooling or 70 watts maximum at convection cooling.
4. Suffix codes for mechanical format and input range are as follows: PD110-XXYZ: “XX” is the model code from the above table. “Y” is
the input range.
(L=10-20VDC, M=18-36VDC, H=36-72VDC); “Z” is the mechanical format (A=open PCB, C=enclosed) EX: PD110-31MC, 18-36VDC input,
enclosed form.
OPEN PCB “A” ENCLOSED “C”
Output #1 Output #2(1) Output #3 Output #4 Maximum
Output
Model Vnom Imin Imax Tol. Vnom Imax Ipeak Tol. Vnom Imin Imax Tol. Vnom Imin Imax Tol. Power
PD110-10 5 V 0.0 A 22.0 A 3% 110 W
PD110-12 12 V 0.0 A 9.0 A 2% 110 W
PD110-13 15 V 0.0 A 7.5 A 2% 110 W
PD110-14 24 V 0.0 A 4.5 A 2% 110 W
PD110-16 30 V 0.0 A 3.6 A 2% 110 W
PD110-23 +5 V 0.8 A 10.0 A 3% +12 V 5 A 9.0 A 3% 110 W
PD110-31 +5 V 0.8 A 10.0 A 3% +12 V 5 A 9.0 A 3% -12 V 0 A 1 A 4% 110 W
PD110-32 +5 V 0.8 A 10.0 A 3% +15 V 4 A 7.5 A 3% -15 V 0 A 1 A 4% 110 W
PD110-40 +5 V 0.8 A 10.0 A 3% +12 V 5 A 9.0 A 3% -12 V 0 A 1 A 4% -5 V 0 A 1 A 4% 110 W
PD110-41 +5 V 0.8 A 10.0 A 3% +15 V 4 A 7.5 A 3% -15 V 0 A 1 A 4% +24 V 0 A 1 A 4% 110 W
PD110-42 +5 V 0.8 A 10.0 A 3% +12 V 5 A 9.0 A 3% -12 V 0 A 1 A 4% +12 V 0 A 1 A 4% 110 W
PD110-45-1 +5 V 0.8 A 10.0 A 3% +12 V 5 A 9.0 A 3% -12 V 0 A 1 A 4% +24 V 0 A 3 A 8% 110 W
PD110-45-2 +5 V 0.8 A 10.0 A 3% +24 V 3 A 5.0 A 5% -12 V 0 A 1 A 4% +12 V 0 A 1 A 4% 110 W
PD110-46 +5 V 0.8 A 10.0 A 3% +15 V 4 A 7.5 A 3% -15 V 0 A 1 A 4% -5 V 0 A 1 A 4% 110 W
OUTPUT VOLTAGE & CURRENT RATINGS PD110
Dimensions shown in inches (mm). Tolerance 0.02 (0.5) maximum. Input connector mates with Molex
housing 09-50-3051 and Molex 2878 series crimp terminal. Output connector mates with Molex housing
09-50-3131 and Molex 2878 series crimp material.
PH: 508 429.9883
FAX: 800 226.2100
Email: sales@xp-iq.com
Holliston, MA 01746 USA
www.XP-iQ.com 54
PD110 13/11/02 3:25 pm Page 2
