MU9C1485A-50TCI - Music Semiconductors

Preliminary Data Sheet

WidePort LANCAM® Family

LANCAM, the MUSIC logo, and the phrase “MUSIC Semiconductors” are registered trademarks of MUSIC Semiconductors. MUSIC is

a trademark of MUSIC Semiconductors. Certain features of this device are patented under US Patent 5,383,146. 2 December 1998 Rev. 2

Block Diagram

DISTINCTIVE CHARACTERISTICS

Ø4096 (4485A/L), 2048 (2485A/L), and 1024

(1485A/L) word CMOS content-addressable

memories (CAMs)

Ø64-bit word width

Ø32-bit I/O compatible with the MU9C1485

ØFast 50 ns compare speed

ØDual configuration register set for rapid

context switching

ØIncreased flexibility of MUSIC’s patented

CAM/RAM partitioning

Ø80-pin TQFP package with the same pinout as

the MU9C1485 and MU9C1965A/L

Ø5 volt (A) or 3.3 volt (L) operation

APPLICATION BENEFITS

Enhances Ethernet and Token-Ring LAN bridges

and switches:

Ø64-bit width stores 48-bit MAC address plus

associated data (Port ID, time stamp,

“permanent” flag)

Ø32-bit I/O supports multiple ports of fast

(100 Mb) Ethernet or Gigabit Ethernet

ØStation list depth flexibility with choice of

pin-compatible device densities and

glue-free cascading

Ø3.3 V olt option for low power systems

ØIndustrial temperature grades for harsh

environments

/CM

/EC

DQ31–0

(32)

I/O BUFFERS

DATA (64)

CONTROL

LOGIC

CAM ARRAY

32K or 16K

WORDS

X 64 BITS

COMPARAND

MASK REGIST ER 1

MASK REGIST ER 2

AD DRESS DECODER

32K or

16K X 2 VALIDITY BITS

PRIO

RITY ENCODER

FLAG

LOGIC

/FF

/FI

/M F

/MI

COMMANDS

& STATUS

215/14

CONTROL

AND STATUS

REGISTERS

17/16

(32) MUX

DEMUX

(32)

SOURCE AND

DESTINATION

SEGMENT

COUNTERS

DATA (64)(32)

/RESET

/MM

/MA

TRANSLATE

(802.3/802.5)

WidePort LANCAM® Family

Rev. 2 2

OPERATIONAL OVERVIEW

The MU9C4485A/L, MU9C2485A/L, and MU9C1485A/L

WidePort LANCAMs are 64-bit wide content-addressable

memories (CAMs), featuring a 32-bit wide interface. This

interface doubles the available I/O bandwidth in many

applications while maintaining the same powerful enhanced

architecture and instruction set as the MU9C2480A/L.

Content-addressable memories, also known as associative

memories, operate in the converse way to random access

memories (RAM). In a RAM, the input to the device is an

address and the output is the data stored at that address. In a

CAM, the input is a data sample and the output is a flag to

indicate a match and the address of the matching data. As a

result, a CAM searches large databases for matching data in a

short, constant time period, no matter how many entries are in

the database. The ability to search data words up to 64 bits

wide allows large address spaces to be searched rapidly and

efficiently. A patented architecture links each CAM entry to

associated data and makes this data available for use after a

successful compare operation.

While the WidePort LANCAMs are optimized for LAN network

address filtering, they are also well suited for applications that

require high-speed data searching, such as virtual memories

and cache management, data compression and encryption,

database accelerators, and image processing.

Skip Bit

Empty Bit

Entry T ype

Valid

Empty

Skip

RAM

T able 1: Entry Types vs. V alidity Bits

Table 2: I/O Cycles

LOW

HIGH

/CM

LOW

HIGH

LOW

HIGH

Cycle T ype

Command Write Cycle

Data Write Cycle

Command Read Cycle

Data Read Cycle

Pinout Diagram

GND

DQ9

DQ10

DQ11

VCC

TES T2

GND

DQ12

DQ13

GND

DQ14

DQ15

DQ16

DQ17

DQ18

DQ19

DQ20

VCC

DQ21

DQ22

DQ23

DQ24

DQ25

DQ26

DQ27

DQ28

DQ29

GND

DQ8

DQ7

DQ6

DQ5

GND

DQ4

DQ3

DQ2

DQ1

DQ0

VCC

/EC

/CM

/MA

GND

/FF

/MI

/MF

/MM

GND

/RESET

VCC

TES T1

DQ31

DQ30

GND

8 0-PIN TQFP

(Top Vie w)

GND

GENERAL DESCRIPTION

To use the WidePort LANCAM, the user loads the data into

the Comparand register , which is automatically compared to

all valid CAM locations. The device then indicates whether

or not one or more of the valid CAM locations contains data

that match the target data. The status of each CAM location

is determined by two validity bits at each memory location.

The two bits are encoded to render four validity conditions:

V alid, Skip, Empty , and Random Access, as shown in T able 1.

The memory can be partitioned into CAM and associated

RAM segments on 16-bit boundaries, but by using one of the

two available mask registers, the CAM/RAM partitioning can

be set at any arbitrary size between zero and 64 bits.

The W idePort LANCAM’ s internal data path is 64 bits wide

for rapid internal comparison and data movement. A data

translation facility converts between IEEE 802.3 (CSMA/CD

“Ethernet”) and 802.5 (T oken Ring) address formats. V ertical

cascading of additional WidePort LANCAMs in a daisy chain

fashion extends the CAM memory depth for large databases.

Cascading requires no external logic. Loading data to the

Control, Comparand, and mask registers automatically triggers

a compare. Compares may also be initiated by a command to

the device. Associated RAM data is available immediately

after a successful compare operation. The Status register reports

the results of compares including all flags and addresses. T wo

mask registers are available and can be used in two different

ways: to mask comparisons or to mask data writes. The random

access validity type allows additional masks to be stored in

the CAM array where they may be retrieved rapidly .

A simple four-wire control interface and commands loaded

into the Instruction decoder control the device. A powerful

instruction set increases the control flexibility and minimizes

software overhead. Additionally , dedicated pins for match and

multiple-match flags enhance performance when the device is

controlled by a state machine. These and other features make

the WidePort LANCAM a powerful associative memory that

drastically reduces search delays.

80-Pin TQFP

(T op V iew)

WidePort LANCAM® Family

Rev. 23

PIN DESCRIPTIONS

/E (Chip Enable, Input, TTL)

The /E input enables the device while LOW. The falling

edge registers the control signals /W, /CM, /EC. The rising

edge locks the daisy chain, turns off the DQ pins, and clocks

the Destination and Source Segment counters. The four

cycle types enabled by /E are shown in Table 2.

/W (Write Enable, Input, TTL)

The /W input selects the direction of data flow during a

device cycle. /W LOW selects a W rite cycle and /W HIGH

selects a Read cycle.

/CM (Data/Command Select, Input, TTL)

The /CM input selects whether the input signals on

DQ31–0 are data or commands. /CM LOW selects Command

cycles and /CM HIGH selects Data cycles.

/EC (Enable Daisy Chain, Input, TTL)

The /EC signal performs two functions. The /EC input

enables the /MF output to show the results of a comparison,

as shown in Figure 6. If /EC is LOW at the falling edge of /E

in a given cycle, the /MF output is enabled. Otherwise, the

/MF output is held HIGH. The /EC signal also enables the

/MF–/MI daisy chain, which serves to select the device

with the highest-priority match in a string of LANCAMs.

T ables 6a and 6b explain the ef fect of the /EC signal on a

device with or without a match in both Standard and

Enhanced modes. /EC must be HIGH during initialization.

DQ31–0 (Data Bus, Three-state I/O, TTL)

The DQ31–0 lines convey data, commands, and status to

and from the WidePort LANCAM, as shown in T able 3. /W

and /CM control the direction and nature of the information

that flows to or from the device. When /E is HIGH, DQ31–0 go

to HIGH-Z.

/MF (Match Flag, Output, TTL)

The /MF output goes LOW when one or more valid

matches occur during a compare cycle. /MF becomes

valid after /E goes HIGH on the cycle that enables the

daisy chain (on the first cycle that /EC is registered LOW

by the previous falling edge of /E; see Figure 6). In a

daisy chain, valid match(es) in higher priority devices

are passed from the /MI input to /MF. If the daisy chain

is enabled but the match flag is disabled in the Control

of the device (/MF=/MI). /MF is HIGH if there is no match

or when the daisy chain is disabled (/E goes HIGH when

/EC was HIGH on the previous falling edge of /E). The

System Match flag is the /MF pin of the last device in

the daisy chain. /MF will be reset when the active

configuration register set is changed.

/MI (Match Input, Input, TTL)

The /MI input prioritizes devices in vertically cascaded

systems. It is connected to the /MF output of the previous

device in the daisy chain. The /MI pin on the first device in

the chain must be tied HIGH.

/MA (Device Match Flag, Output, TTL)

The /MA output is LOW when one or more valid matches

occur during the current or the last previous compare

cycle. The /MA output is not qualified by /EC or /MI,

and reflects the match flag from that specific device’s

Status register . /MA will be reset when the active register

set is changed.

/MM (Device Multiple Match Flag, Output, TTL)

The /MM output is LOW when more than one valid

match occurs during the current or the last previous

compare cycle. The /MM output is not qualified by /EC

or /MI, and reflects the multiple match flag from that

specific device’ s Status register. /MM will be reset when

the active register set is changed.

/FF (Full Flag, Output, TTL)

If enabled in the Control register , the /FF output goes LOW

when no empty memory locations exist within the device

(and in the daisy chain above the device as indicated by

the /FI pin). The System Full flag is the /FF pin of the last

device in the daisy chain, and the Next Free address resides

in the device with /FI LOW and /FF HIGH. If disabled in the

Control register, the /FF output only depends on the /FI

input (/FF = /FI).

/FI (Full Input, Input, TTL)

The /FI input generates a CAM-Memory-System-Full

indication in vertically cascaded systems. It is connected

to the /FF output of the previous device in the daisy chain.

The /FI pin on the first device in a chain must be tied LOW.

All signals are implemented in CMOS technology with TTL levels. Signal names that start with a slash (“/”) are active LOW. Inputs

should never be left floating. The CAM architecture draws large currents during compare operations, mandating the use of good layout

and bypassing techniques. Refer to the Electrical Characteristics section for more information.

WidePort LANCAM® Family

Rev. 2 4

PIN DESCRIPTIONS

Continued

/RESET (Reset, Input, TTL)

/RESET must be driven LOW to place the device in a known

state before operation, which will reset the device to the

conditions shown in Table 5. The /RESET pin should be

driven by TTL levels, not directly by an RC timeout. /E

must be kept HIGH during /RESET .

TEST1, TEST2 (T est, Input, TTL)

These pins enable MUSIC production test modes that are

not usable in an application. They should be connected to

ground, either directly or through a pull-down resistor, or

they may be left unconnected. These pins may not be

implemented on all versions of these products.

VCC, GND (Positive Power Supply, Ground)

These pins are the power supply connections to the

W idePort LANCAM. VCC must meet the voltage supply

requirements in the Operating Conditions section relative

to the GND pins, which are at 0 Volts (system reference

potential), for correct operation of the device. All the

ground and power pins must be connected to their

respective planes with adequate bulk and high frequency

bypassing capacitors in close proximity to the device.

The MU9C2485A/L and MU9C1485A/L are compatible

with the original MU9C1485 connections, and may be

operated at -90 or slower switching characteristics

without the GND connections on pins 1, 2, 20, 21, 22, 41,

42, 60, 61, and 62.

FUNCTIONAL DESCRIPTION

The WidePort LANCAM is a content-addressable

memory (CAM) with 32-bit I/O for network address

filtering, virtual memory , data compression, caching, and

table lookup applications. The memory consists of static

CAM, organized in 64-bit data fields. Each data field can

be partitioned into a CAM and a RAM subfield on 16-bit

boundaries. The contents of the memory can be randomly

accessed or associatively accessed by the use of a

compare. During automatic comparison cycles, data in

the Comparand register is automatically compared with

the “Valid” entries in the memory array . The Device ID can be

read using a TCO PS instruction (see T able 13).

The data inputs and outputs of the W idePort LANCAM

are multiplexed for data and instructions over a 32-bit

I/O bus. Internally, data is handled on a 64-bit basis,

since the Comparand register, the mask registers, and

each memory entry are 64 bits wide. Memory entries are

globally configurable into CAM and RAM segments on

16-bit boundaries, as described in US Patent 5,383,146

assigned to MUSIC Semiconductors. Seven different

CAM/RAM splits are possible, with the CAM width

going from one to four segments, and the remaining RAM

width going from three to zero segments. Finer resolution

on compare width is possible by invoking a mask register

during a compare, which does global masking on a bit

basis. The CAM subfield contains the associative data,

which enters into compares, while the RAM subfield

contains the associated data, which is not compared. In

LAN bridges, the RAM subfield can hold, for example,

port-address and aging information related to the

destination or source address information held in the

CAM subfield of a given location. In a translation

application, the CAM field can hold the dictionary

entries, while the RAM field holds the translations, with

almost instantaneous response.

T able 3: DQ Bus Multiplexing

LOW

HIGH

LOW

HIGH

/CM

LOW

HIGH

Cycle Type

Command write

Command read

TCO 2nd cycle

Data write

Data read

“f” Bit

DQ31–16

Non-TCO Instruction

TCO Instruction (Read register)*

TCO Instruction (Write register)

Status Register bits 31–16

Status Register bits 31–16†

Data to CR, MRX, Mem.

Data from CR, MRX, Mem.

DQ15–0

XXXX

Absolute Address

XXXX

Value to Register

Status Register bits 15–0

Data to CR, MRX, Mem.

Data from CR, MRX, Mem.

Notes: *

†

A CW of a TCO Instruction with the “f” bit set to 0 sets up a Register read in the following cycle. The

following cycle must be a Command Read cycle, otherwise the register read will be cancelled.

Upper 16 bits will be Status Register bits 31–16, except for a read of the Page Address register, in which

case they will be all zeros.

WidePort LANCAM® Family

Rev. 25

Each entry has two validity bits (known as Skip bit and

Empty bit) associated with it to define its particular type:

empty, valid, skip, or RAM. When data is written to the

active Comparand register, and the active Segment

Control register reaches its terminal count, the contents

of the Comparand register are automatically compared

with the CAM portion of all the valid entries in the

memory array. For added versatility, the Comparand

time. A Compare instruction can then be used to force

another compare between the Comparand register and

the CAM portion of memory entries of any one of the

four validity types. After a Read or Move from Memory

operation, the validity bits of the location read or moved

will be copied into the Status register , where they can be

read from the Status register using Command Read cycles.

Data can be moved from one of the data registers (CR,

MR1, or MR2) to a memory location that is based on the

results of the last comparison (Highest-Priority Match

or Next Free), or to an absolute address, or to the location

pointed to by the active Address register. Data can also

be written directly to the memory from the DQ bus using

any of the above addressing modes. The Address

increment or decrement, allowing DMA-type reading or

writing from memory .

Two sets of configuration registers (Control, Segment

Control, Address, Mask Register 1, and Persistent Source

and Destination) are provided to permit rapid context

switching between foreground and background

activities. Writes, reads, moves, and compares are

controlled by the currently active set of configuration

registers. The foreground set would typically be pre-

loaded with values useful for comparing input data, often

called filtering, while the background set would be pre-

loaded with values useful for housekeeping activities

such as purging old entries. Moving from the foreground

task of filtering to the background task of purging can

be done by issuing a single instruction to change the

current set of configuration registers. The match

condition of the device is reset whenever the active

The active Control register determines the operating

conditions within the device. Conditions set by this

flag, enable or disable Full flag, default data translation,

CAM/RAM partitioning, disable or select masking

conditions, disable or select auto-incrementing or

auto-decrementing the Address register, and select

Standard (compatible with the MU9C1485) or Enhanced

mode. The active Segment Control register contains

separate counters to control the writing of 32-bit data

segments to the selected persistent destination, and to

control the reading of 32-bit data segments from the

selected persistent source.

There are two active mask registers at any one time,

which can be selected to mask comparisons or data

writes. Mask Register 1 has both a foreground and

background mode to support rapid context switching.

Mask Register 2 does not have this mode, but can be

shifted left or right one bit at a time. For masking

comparisons, data stored in the active selected mask

compared against the valid contents of the memory. If a

bit is set HIGH in the mask register , the same bit position

in the Comparand register becomes a “don’t care” for

the purpose of the comparison with all the memory

locations. During a Data W rite cycle or a MOV instruction,

data in the specified active mask register can also

determine which bits in the destination will be updated.

If a bit is HIGH in the mask register, the corresponding

bit of the destination is unchanged.

The match line associated with each memory address is

fed into a priority encoder where multiple responses are

resolved, and the address of the highest-priority

responder (the lowest numerical match address) is

generated. In the LAN bridge application, a multiple

response might indicate an error. In other applications

the existence of multiple responders may be valid.

Four input control signals and commands loaded into an

instruction decoder control the W idePort LANCAM. Two

of the four input control signals determine the cycle type.

The control signals tell the device whether the data on the

I/O bus represents data or a command, and is input or output.

Commands are decoded by instruction logic and control

moves, forced compares, validity bit manipulations, and the

data path within the device. Registers (Control, Segment

Control, Address, Next Free Address, etc.) are accessed using

Temporary Command Override instructions. The data path

from the DQ bus to/from data resources (comparand, masks,

and memory) within the device are set until changed by Select

Persistent Source and Destination instructions.

After a Compare cycle (caused by either a data write to the

Comparand or mask registers, a write to the Control register,

or a forced compare), the Status register contains the

FUNCTIONAL DESCRIPTION

Continued

WidePort LANCAM® Family

Rev. 2 6

FUNCTIONAL DESCRIPTION

Continued

address of the Highest-Priority Matching location in that

device, concatenated with its page address, along with

flags indicating internal match, multiple match, and full.

When the Status register is read with a Command Read

cycle, the device with the Highest-priority match will

respond, outputting the System Match address to the DQ

bus. The internal Match (/MA) and Multiple match (/MM)

flags are also output on pins. Another set of flags (/MF

and /FF) that are qualified by the match and full flags of

previous devices in the system are also available directly

on output pins, and are independently daisy-chained to

provide System Match and Full flags in vertically cascaded

LANCAM arrays. In such arrays, if no match occurs during

a comparison, read access to the memory and all the

registers except the Next Free register is denied to prevent

device contention. In a daisy chain, all devices will respond

to Command and Data Write cycles, depending on the

conditions shown in T ables 6a and 6b, unless the operation

involves the Highest-Priority Match address or the Next

Free address; in which case, only the specific device

having the Highest-Priority match or the Next Free

address will respond.

A Page Address register in each device simplifies vertical

expansion in systems using more than one LANCAM. This

system initialization, which then serves as the higher-order

address bits. A Device Select register allows the user to

target a specific device within a vertically cascaded system

by setting it equal to the Page Address Register value, or

to address all the devices in a string at the same time by

setting the Device Select value to FFFFH.

Figure 1a shows expansion using a daisy chain. Note that

system flags are generated without the need for external

logic. The Page Address register allows each device in the

vertically cascaded chain to supply its own address in the

event of a match, eliminating the need for an external priority

encoder to calculate the complete Match address at the

expense of the ripple-through time to resolve the highest-

priority match. The Full flag daisy-chaining allows

Associative writes using a Move to Next Free Address

instruction which does not need a supplied address.

Figure 1b shows an external PLD implementation of a simple

priority encoder that eliminates the daisy chain ripple-

through delays for systems requiring maximum performance

from many CAMS.

Figure 1a: V ertical Cascading Figure 1b: External Prioritizing

/MA

WidePort

LANCAM

/MI

Vcc

SYSTEM

MATCH

PLD

WidePort

LANCAM

WidePort

LANCAM

WidePort

LANCAM

Vcc

SYSTEM F UL L

SYSTE M MATC H

Wideport

LANCAM

/CM

/EC

DQ31-0

/MI

/FI

/FF

/MF

/MI

/FI

/FF

/MF

/CM

/EC

DQ31-0

/CM

/EC

DQ31-0

/CM

/EC

DQ31-0

Wideport

LANCAM

/MI

/FI

/FF

/MF

Wideport

LANCAM

WidePort LANCAM® Family

Rev. 27

OPERATIONAL CHARACTERISTICS

Throughout the following, “aaaH” represents a three-

digit hexadecimal number “aaa,” while “bbB”

represents a two-digit binary number “bb.” All memory

locations are written to or read from in 32-bit segments.

Segment 0 corresponds to the lowest order bits (bits

31–0) and Segment 1 corresponds to the highest order

bits (bits 63–32).

THE CONTROL BUS

Refer to the Block Diagram for the following discussion.

The inputs Chip Enable (/E), W rite Enable (/W), Command

Enable (/CM), and Enable Daisy Chain (/EC) are the primary

control mechanism for the WidePort LANCAM. The /EC

input of the Control bus enables the /MF Match flag output

when LOW and controls the daisy chain operation.

Instructions are the secondary control mechanism. Logical

combinations of the Control Bus inputs, coupled with the

execution of Select Persistent Source (SPS), Select Persistent

Destination (SPD), and Temporary Command Override

(TCO) instructions allow the I/O operations to and from the

DQ31–0 lines to the internal resources, as shown in T able 4.

The Comparand register is the default source and destination

for Data Read and Write cycles. This default state can be

overridden independently by executing a Select Persistent

Source or Select Persistent Destination instruction, selecting

a different source or destination for data. Subsequent Data

Read or Data Write cycles will access that source or destination

until another SPS or SPD instruction is executed. The currently

selected persistent source or destination can be read back

through a TCO PS or PD instruction. The sources and

destinations available for persistent access are those resources

on the 64-bit bus: Comparand register, Mask Register 1, Mask

The default destination for Command Write cycles is the

Instruction decoder , while the default source for Command

Read cycles is the Status register. The entire 32-bit Status

T emporary Command Override (TCO) instructions provide

access to the Control register, the Page Address register,

the Segment Control register , the Address register, the Next

Free Address register, and Device Select register. These

instructions are only active for one Command W rite cycle

to write a value into a register , or one Command Write cycle

followed by a Command Read cycle to read a register’s

contents. Each of these 16-bit registers is read out on the

DQ15–0 pins, with the upper 16 bits of the Status register

output on the DQ31–16 pins (except in the case of a Page

Address register read where 0s will be read on DQ31–16

instead), as shown in Table 3.

The data and control interfaces to the W idePort LANCAM

are synchronous. During a Write cycle, the Control and

Data inputs are registered by the falling edge of /E. When

writing to the persistently selected data destination, the

Destination Segment counter is clocked by the rising edge

of /E. During a Read cycle, the Control inputs are registered

by the falling edge of /E, and the Data outputs are enabled

while /E is LOW. When reading from the persistently

selected data source, the Source Segment counter is clocked

by the rising edge of /E.

THE REGISTER SET

The Control, Segment Control, Address, Mask Register 1,

and the Persistent Source and Destination registers are

duplicated, with one set termed the Foreground set, and

the other the Background set. The active set is chosen by

issuing Select Foreground Registers or Select Background

Registers instructions. By default, the Foreground set is

active after a reset. Having two alternate sets of registers

that determine the device configuration allows for a rapid

return to a foreground network filtering task from a

background housekeeping task.

W riting a value to the Control register or writing data to the

last segment of the Comparand or either mask register will

cause an automatic comparison to occur between the

contents of the Comparand register and the words in the

CAM segments of the memory marked valid, masked by

MR1 or MR2 if selected in the Control register .

Instruction Decoder

The Instruction decoder is the write-only decode logic for

instructions and is the default destination for Command

Write cycles using the DQ31–16 lines. If the instruction

requires an absolute address or register value, the “f”

Address Field flag (bit 11) of the instruction is set to a “1,”

and the data on the DQ15–0 lines are written to the proper

TCO, and the “f” bit is not set, the contents of the register

specified by the TCO may be read back by a successive

Command Read cycle to the DQ15–0 signal lines.

If the Address Field flag is set in a memory access

instruction, the absolute address supplied on the DQ15–0

lines is loaded into the Address register , and the instruction

completes at the new address. If the Address Field flag is not

set, the memory access occurs at the address currently

WidePort LANCAM® Family

Rev. 2 8

T able 4: Input/Output Operations

/CM

I/O Status

OUT

HIGH-Z

OUT

HIGH-Z

Operation

Load Instruction decoder

Load Address register

Load Control register

Load Page Address register

Load Segment Control register

Load Device Select register

Deselected

Read Next Free Address register

Read Address register

Read Status Register bits 31–0

Read Control register

Read Page Address register

Read Segment Control register

Read Device Select register

Read Current Persistent Source or Destination

Deselected

Load Comparand register

Load Mask Register 1

Load Mask Register 2

Write Memory Array at address

Write Memory Array at Next Free address

Write Memory Array at Highest-Priority match

Deselected

Read Comparand register

Read Mask Register 1

Read Mask Register 2

Read Memory Array at address

Read Memory Array at Highest-Priority match

Deselected

Cycle T ype

Cmd Write

Cmd Read

Data Write

Data Read

Notes

3, 10

5, 8

6, 8

5, 8

7, 8

SPS

SPD

TCO

Notes:

1. Default Command Write cycle destination (does not require a TCO instruction).

2. To load a value into a register using a TCO instruction takes one Command Write cycle with the “f” bit equal to 1, and

the value to be loaded into the selected register placed in DQ15–0.

3. Reading the contents of a register using a TCO instruction takes two cycles. The first cycle is a Command Write of a

TCO instruction with the “f” bit equal to 0. If the next cycle is a Command Read, the value stored in the selected register

will be read out on the DQ15–0 lines. Additionally, bits 31–16 of the Status register will be read out on the DQ31–16 lines,

except in the case of a Page Address read where 0s will be read on DQ31–16 instead.

4. Default Command Read cycle source (does not require a TCO instruction).

5. Default persistent source and destination after Reset. If other resources were sources or destinations, SPD CR or SPS

CR restores the Comparand register as the destination or source.

6. Selected by executing a Select Persistent Destination instruction.

7. Selected by executing a Select Persistent Source instruction.

8. Access is performed in one or two 32-bit Read or Write cycles. The Segment Control register is used to control the

selection of the desired 32-bit segement(s) by establishing the Segment counters’ limits and start values.

9. Device is deselected if Device Select register setting does not equal Page Address register setting, unless the Device

Select register is set to FFFFH which allows only write access to the device, except in the case of a match. (Writes to

the Device Select register are always active.) Device may also be deselected under locked daisy chain conditions as

shown in Tables 6a and 6b.

10. A Command Read cycle after a TCO PS or TCO PD reads back the Instruction decoder bits that were last set to select a

persistant source or destination. The TCO PS instruction will also read back the Device ID.

OPERATIONAL CHARACTERISTICS

Continued

WidePort LANCAM® Family

Rev. 29

contained in the Address register. After the execution of the

instruction, the Address register will increment, decrement, or

stay the same value depending on the setting of Control

Control Register (CT)

The Control register is composed of a number of switches

that configure the W idePort LANCAM, as shown in T able

9. It is written or read through DQ15–0 using a TCO CT

instruction on DQ31–16. On read cycles, DQ31–16 will be

the upper 16 bits of the Status register . If bit 15 of the value

written during a TCO CT is a 0, the device is reset (and all

other bits are ignored). See T able 5 for the Reset states. Bit

15 always reads back as a 0. A write to the Control register

causes an automatic compare to occur (except in the case

of a reset). Either the Foreground or Background Control

been selected, and only the active Control register will be

written to or read from.

If the Match flag is disabled through bits 14 and 13, the

internal match condition, /MA(int), used to determine a

daisy-chained device’ s response is forced HIGH as shown

in Tables 6a and 6b, so that Case 6 is not possible,

effectively removing the device from the daisy chain. With

the Match flag disabled, /MF=/MI and operations directed

to Highest-priority Match locations are ignored. Normal

operation of the device is with the /MF enabled. The Match

Flag Enable field has no effect on the /MA or /MM output

pins or Status Register bits. These bits always reflect the

true state of the device.

If the Full Flag is disabled through bits 12 and 11, the

device behaves as if it were full and ignores instructions to

Next Free address. Additionally , writes to the Page Address

normally. Additionally, with the /FF disabled, /FF=/FI.

Normal operation of the device is with the /FF enabled. The

Full Flag Enable field has no effect on the /FL Status Register

bit. This bit always reflects the true state of the device.

The IEEE Translation control at bits 10 and 9 can be used

to enable the translation hardware for writes to 64-bit

resources in the device. When translation is enabled, the

bits are reordered as shown in Figure 2.

Control Register bits 8–6 control the CAM/RAM

partitioning. The CAM portion of each word may be sized

from a full 64 bits down to 16 bits in 16-bit increments. The

RAM portion can be at either end of the 64-bit word.

Compare masks may be selected by bits 5 and 4. Mask

mask compare operations. The address register behavior is

controlled by bits 3 and 2, and may be set to increment,

decrement, or neither after a memory access. Bits 1 and 0

set the operating mode: Standard (compatible with the

MU9C1485) as shown in Table 6a, or Enhanced as shown

in T able 6b. The device will reset to the Standard mode and

follow the operating responses in T able 6a. When operating

DQ31 DQ24 DQ23 DQ16 DQ15 DQ8 DQ7 DQ0

Figure 2: IEEE 802.3/802.5 Format Mapping

OPERATIONAL CHARACTERISTICS

Continued

Table 5: Device Control State after Reset

CAM Status

Validity bits at all memory locations

Match and Full flag outputs

IEEE 802.3-802.5 Input Translation

CAM/RAM Partitioning

Comparison Masking

Address register auto-increment or -decrement

Source and Destination Segment counters count ranges

Address register and Next Free Address register

Page Address and Device Select registers

Control register after reset (including CT15)

Persistent Destination for Command writes

Persistent Source for Command reads

Persistent Source and Destination for Data reads and writes

Operating Mode

Configuration Register set

/RESET Condition

Skip = 0, Empty = 1 (empty)

Enabled

Not Translated

64 bits CAM, 0 bits RAM

Disabled

0B to 1B; loaded with 0B

Contain all 0s

Contain all 0s (no change on Software reset)

Contains 0008H

Instruction decoder

Status register

Comparand register

Standard

Foreground

WidePort LANCAM® Family

Rev. 2 10

OPERATIONAL CHARACTERISTICS

Continued

in Enhanced mode, it is not necessary to unlock the daisy

chain with a NOP instruction before command or data writes

after a non-matching compare, as required in Standard mode.

Segment Control Register (SC)

The Segment Control register, as shown in Table 10, is

accessed using a TCO SC instruction with the register contents

placed on DQ15–0. On read cycles, DQ31–16 will be the upper

16 bits of the Status register, and D15, D10, D5, and D2 always

read back as 0s. Reserved locations D14, D12, D9, D7, D4, and

D1 should always be set to 0 and as such will also read back as

0s. Either the Foreground or Background Segment Control

been selected, and only the active Segment Control register

will be written to or read from.

The Segment Control register contains dual independent

incrementing counters with limits, one for data reads and

one for data writes. These counters control which 32-bit

segment of the 64-bit internal resource is accessed during

a particular data cycle on the 32-bit data bus. The actual

destination for data writes and source for data reads (called

the persistent destination and source) are set independently

with SPD and SPS instructions, respectively.

Each of the two counters consists of a start limit, an end

limit, and the current segment pointer, each a single bit

representing either the lower segment (0) or the upper

segment (1). The current segment pointer can be set to

either 0 or 1 even if that value is outside the range set by

the start and end segments. The counters count up from

the current segment pointer to the end limit and then roll

over back to the start limit.

If a sequence of data writes or reads is interrupted, the

Segment Control register can be reset to its initial start limit

values with the RSC instruction. After a reset, both Source

and Destination counters are set to count from Segment 0

to Segment 1 with an initial value of 0.

Page Address Register (P A)

The Page Address register is loaded using a TCO PA

instruction on DQ31–16 with a user selected 16-bit value

(not FFFFH) on DQ15–0. During reads of the PA register,

DQ31–16 will all be 0. The entry in the P A register is used to

give a unique address to the different devices in a daisy

chain. In a daisy chain, the PA value of each device is

loaded using the SFF instruction to advance to the next

device, as shown in the “Setting Page Address Register

Values” section. A software reset (using the Control

Device Select Register (DS)

The Device Select register is used to select a specific (target)

device using the TCO DS instruction in DQ31–16 and

setting the 16-bit DS value in DQ15–0 equal to the target’ s

PA value. The DS register can be read through DQ15–0

with DQ31–16 returning the upper 16 bits of the Status

devices. However, in this case, the ability to read information

out of the device is restricted as shown in T ables 6a and 6b.

A software reset (using the Control register) does not affect

the Device Select register .

Address Register (AR)

The Address register points to the CAM memory location

to be operated upon when a M@[AR] or M@aaaH is part

of the instruction. It can be loaded directly by using a TCO

AR instruction or indirectly by using an instruction requiring

an absolute address, such as MOV aaaH, CR,V. The AR

returning the upper 16 bits of the Status register. After

being loaded, the Address register value will then be used

for the next memory access referencing the Address register .

A reset sets the Address register to zero.

Control Register bits CT3 and CT2 set the address to

automatically increment or decrement (or not change)

during sequences of Command or Data cycles. The Address

includes M@[AR] or M@aaaH, or after a data access to

the end limit segment (as set in the Segment Control

M@[AR] or M@aaaH.

Either the Foreground or Background Address register will

be active, depending on which register set has been

selected, and only the active Address register will be written

to or read from.

Next Free Address Register (NF)

The W idePort LANCAM automatically stores the address

of the first empty memory location in the Next Free Address

for M@NF operations. The Next Free Address register,

shown in T able 11, can be read through DQ15–0 using a TCO

NF instruction. DQ31–16 will return the upper 16 bits of the

Status register. By taking /EC LOW during the TCO NF

instruction cycle, only the device with /FI LOW and /FF

HIGH will output the contents of its Next Free Address

daisy-chained devices. The Next Free address may be read

from a specific device in the chain by setting the Device

WidePort LANCAM® Family

Rev. 211

Select register to the value of the desired device’s Page

address and leaving /EC HIGH.

The Full Flag daisy chain causes only the device whose /FI

input is LOW and /FF output HIGH to respond to an

instruction using the Next Free address. After a reset, the

Next Free Address register is set to zero.

Status Register

The 32-bit Status register, shown in Table 12, is the default

source for Command Read cycles. Bit 31 is the internal Match

flag, which will go LOW if a match was found in this particular

device. Bit 30 is the internal Multiple Match flag, which will go

LOW if a Multiple match was detected. Bit 29 is the internal

Full flag, which will go LOW if the particular device has no

empty memory locations. Bits 28 and 27 are the Skip and Empty

Validity bits, which reflect the validity of the last memory

location read. After a reset, the Skip and Empty bits will read

11 until a read or move from memory has occurred. The rest of

the Status register contains the Page address of the device

and the address of the Highest-Priority match. After a reset or

a no-match condition, the match address bits will be all 1s.

Comparand Register (CR)

The 64-bit Comparand register is the default destination

for data writes and reads, using the Segment Control register

to select which of the two 32-bit segments of the Comparand

and destination for data writes and reads can be changed

to the mask registers or memory by SPS and SPD

OPERATIONAL CHARACTERISTICS

Continued

NOTES:

1. Exceptions are:

A) A write to the Device Select register is always active in all devices;

B) A write to the Page Address register is active in the device with /FI LOW and /FF HIGH; and

C) The Set Full Flag (SFF) instruction is active in the device with /FI LOW and /FF HIGH.

2. If /MF is disabled in the Control register, /MA (Internal) is forced HIGH preventing a Case 6 response.

3. This is NO for a MOV instruction involving Memory at Next Free address if /FI is HIGH or the device is full.

4. This is NO if the Persistent Destination is Memory at Next Free address and /FI is HIGH or the device is full.

5. For a Command Read following a TCO NF instruction, this is YES if the device contains the first empty location in a daisy chain

(for example, /FI LOW and /FF HIGH) and NO if it does not.

6. This is NO for a MOV or VBC instruction involving Memory at Highest-Priority match.

7. This is NO if the Persistent Destination is Memory at Highest-Priority match.

Table 6a: Standard Mode Device Select Response

Case

Internal

/EC(int)

Internal

/MA (int)

External

/MI

Device Select

Reg.

DS=FFFFH

DS=PA

DS≠FFFFH and

DS≠PA

Command

Write1

YES3

Data Write

YES4

Command

Read

YES

NO5

YES5

Data Read

YES

T able 6b: Enhanced Mode Device Select Response

Case

Internal

/EC(int)

Internal

/MA (int)

External

/MI

Device Select

Reg.

DS = FFFFH

DS = P A

DS ≠ FFFFH

and DS ≠ PA

Command

Write1

YES3

YES3,6

YES3

Data Write

YES4

YES4,7

YES4

Command

Read

YES

NO5

YES5

Data Read

YES

WidePort LANCAM® Family

Rev. 2 12

OPERATIONAL CHARACTERISTICS

Continued

instructions. During an automatic or forced compare, the

Comparand register is simultaneously compared against

the CAM portion of all memory locations with the correct

validity condition. Automatic compares always compare

against valid memory locations, while forced compares,

using CMP instructions, can compare against memory

locations tagged with any specific validity condition.

The Comparand register may be shifted one bit at a time to

the right or left by issuing a Shift Right or Shift Left

instruction, with the right and left limits for the wrap-around

determined by the CAM/RAM partitioning set in the Control

CAM partition will reappear at the MSB of the CAM

partition. Likewise, bits shifted off the MSB of the CAM

partition will reappear at the LSB during shift lefts.

Mask Registers (MR1, MR2)

The Mask registers can be used in two different ways, either

to mask compares or to mask data writes and moves. Either

mask register can be selected in the Control register to

mask every compare, or selected by instructions to

participate in data writes or moves to and from Memory . If

a bit in the selected mask register is set to a 0, the

corresponding bit in the Comparand register will enter into

a masked compare operation. If a Mask bit is a 1, the

corresponding bit in the Comparand register will not enter

into a masked compare operation. Bits set to 0 in the mask

or memory location to be updated when masking data writes

or moves, while a bit set to 1 will prevent that bit in the

destination from being changed.

Either the Foreground or Background MR1 can be set

active, but after a reset, the Foreground MR1 is active

by default. MR2 incorporates a sliding mask, where the

data can be replicated one bit at a time to the right or left

with no wrap-around by issuing a Shift Right or Shift

Left instruction. The right and left limits are determined

by the CAM/RAM partitioning set in the Control register .

For a Shift Right the upper limit bit is replicated to the

next lower bit, while for a Shift Left the lower limit bit is

replicated to the next higher bit.

THE MEMORY ARRAY

Memory Organization

The Memory array is organized into 64-bit words with each

word having an additional two validity bits (Skip and

Empty). By default, all words are configured to be 64 CAM

cells. However , bits 8–6 of the Control register can divide

each word into a CAM field and a RAM field. The RAM

field can be assigned to the least-significant or most-

significant portion of each entry. The CAM/RAM

partitioning is allowed on 16-bit boundaries, permitting

selection of the configurations shown in Table 9, bits 8–6

(e.g., “001” sets the 48 MSBs to CAM and the 16 LSBs to

RAM). Memory Array bits designated as RAM can be used

to store and retrieve data associated with the CAM content

at the same memory location.

Memory Access

There are two general ways to get data into and out of the

memory array: directly or by moving the data through the

Comparand or mask registers.

The first way, through direct reads or writes, is set up by

issuing a Set Persistent Destination (SPD) or Set Persistent

Source (SPS) command. The addresses for the direct access

can be directly supplied, supplied from the Address register,

supplied from the Next Free Address register, or supplied

as the Highest-Priority Match address. Additionally , all the

direct writes can be masked by either mask register .

The second way is to move data via the Comparand or

mask registers. This is accomplished by issuing Data Move

commands (MOV). Moves using the Comparand register

can also be masked by either of the mask registers.

I/O CYCLES

The WidePort LANCAM supports four basic I/O cycles: Data

Read, Data Write, Command Read, and Command Write. The

type of cycle is determined by the states of the /W and /CM

control inputs. These signals are registered at the beginning

of a cycle by the falling edge of /E. T able 3 shows how the /W

and /CM lines select the cycle type and how the data bus is

utilized for each.

During Read cycles, the DQ31–0 outputs are enabled after

/E goes LOW. During Write cycles, the data or command

to be written is captured from DQ31–0 at the beginning of

the cycle by the falling edge of /E. Figures 3 and 4 show

Read and W rite cycles respectively . Figure 5 shows typical

cycle-to-cycle timing with the Match flag valid at the end

WidePort LANCAM® Family

Rev. 213

OPERATIONAL CHARACTERISTICS

Continued

of the Comparand W rite cycle, assuming /EC is LOW at the

start of this cycle. Data writes and reads to the comparand,

mask registers or memory occur in one or two 32-bit cycles,

depending on the settings in the Segment Control register .

The Compare operation automatically occurs during Data

writes to the Comparand or mask registers when the

destination segment counter reaches the end count set in

the Segment Control register. If there was a match, the

second cycle reads status or associated data, depending

on the state of /CM. For cascaded devices, /EC needs to be

LOW at the start of the cycle prior to any cycle that requires

a locked daisy chain, such as a Status register or associated

data read after a match. If there is no match in Standard

mode, the output buffers stay HIGH-Z, and the daisy chain

must be unlocked by taking /EC HIGH during a NOP or

other non-functioning cycle, as indicated in Table 6a.

Figure 6 shows how the internal /EC timing holds the daisy

chain locking effect over into the next cycle. In the Enhanced

mode, this NOP is not needed before data or command

writes following a non-matching compare, as indicated by

Table 6b. A single-chip system does not require daisy-

chained match flag operation, hence /EC could be tied HIGH

and the /MA pin or flag in the Status register used instead

of /MF, allowing access to the device regardless of the

match condition.

The minimum timings for the /E control signal are given in

the Switching Characteristics section. Note that at minimum

timings the /E signal is non-symmetrical, and that different

cycle types have different timing requirements, as given in

T able 8.

Figure 3: Read Cycle

Figure 4: Write Cycle

Figure 5: Cycle to Cycle Timing Example

DQ15–0

/CM

/EC

DATA OUT

DQ31–0

/CM

COMPARAND W RITE

CYCLE

STATUS READ

CYCLE ASS OCIATED DATA

READ CYCLE

DATA DATA

/ M F FL AGS UPD ATED

/M A, /M M

/EC

/M F MATCH FLAG V ALID

DQ15–0

/CM

WidePort LANCAM® Family

Rev. 2 14

OPERATIONAL CHARACTERISTICS

Continued

COMPARE OPERATIONS

During a Compare operation, the data in the Comparand

simultaneously . Any mask register used during compares must

be selected beforehand in the Control register. There are two

ways compares are initiated: Automatic and Forced compares.

Automatic compares perform a compare of the contents of the

Comparand register against Memory locations that are tagged

as “Valid,” and occur whenever the following happens:

ØThe Destination Segment counter in the Segment

Control register reaches its end limit during writes to

the Comparand or mask registers.

ØAfter a command write of a TCO CT is executed (except

for a software reset), so that a compare is executed

with the new settings of the Control register.

Forced compares are initiated by CMP instructions

using one of the four validity conditions, V, R, S, and E. The

forced compare against “Empty” locations automatically

masks all 64 bits of data to find all locations with the validity

bits set to “Empty”, while the other forced compares are

only masked as selected in the Control register.

VERTICAL CASCADING

WidePort LANCAMs can be vertically cascaded to

increase system depth. Through the use of flag daisy-

chaining, multiple devices will respond as an integrated

system. The flag daisy chain allows all commands to be

issued globally, with a response only in the device

containing the Highest-Priority Matching or Next Free

location. When connected in a daisy chain, the last device’ s

Full flag and Match flag accurately report the condition for

the whole string. A system in which W idePort LANCAMs

are vertically cascaded using daisy-chaining of the flags is

shown in Figure 1a.

To operate the daisy chain, the Device Select registers are

set to FFFFH to enable all devices to execute Command

Write and Data Write cycles. In normal operation, read

cycles are enabled from the device with the highest-priority

match by locking the daisy chain (see “Locked Daisy Chain”

section). An individual device in the chain may be targeted

for a read or write operation by temporarily setting the

Device Select registers to the page address of the target

device. Setting the Device Select registers back to FFFFH

restores the operation of the entire daisy chain.

Match Flag Cascading

The Match Flag daisy chain cascading is used for three

purposes: first, to allow operations on Highest-priority

Match addresses to be issued globally over the whole

string; second, to provide a system wide match flag;

third, to lock out all devices except the one with the

Highest-Priority match for instructions such as Status

reads after a match. The Match flag logic causes only

the highest-priority device to operate on its Highest-priority

Match location while devices with lower-priority matches

ignore Highest-priority Match operations. The lock-out feature

is enabled by the match flag cascading and the use of the /EC

control signal, as shown in Tables 6a and 6b.

The ripple delay of the flags when connected in a daisy

chain may require the extension of the /E HIGH time until

the logic in all devices has settled out. In a string of “n”

devices, the /E HIGH time should be greater than:

tEHMFV + (n-2)· tMIVMFV

If the last device’s Match flag is required by external

logic or a state machine before the start of the next CAM

cycle, one additional tMIVMFV should be added to the

/E HIGH time along any required setup time and delays

for the external logic.

Locked Daisy Chain

In a locked daisy chain, the highest-priority device is the

one with /MI HIGH and /MF LOW. In Standard mode, only

this device will respond to command and data reads and

writes, until the daisy chain has been unlocked by taking

/EC HIGH. This allows reading the associated data field

from only the Highest-Priority Match location anywhere in

a string of devices, or the Match address from the Status

updating the entry stored at the Highest-Priority Match

location. In Enhanced mode, devices are enabled to respond

to some command and data writes, as noted in Tables 6a

and 6b, but not command and data reads.

Figure 6: /EC(Int) Timing Diagram

/EC

/EC (INT )

/MF

WidePort LANCAM® Family

Rev. 215

which occur only in the device with the highest match; and

data writes or move instructions involving NF, which occur

only in the device with /FI LOW and /FF HIGH. Enhanced

mode speeds up system performance by eliminating the need

to unlock the daisy chain before Command or Data Write

cycles.

Full Flag Cascading

The Full Flag daisy chain cascading is used for three

purposes: first, to allow instructions that address Next Free

locations to operate globally; second, to provide a system

wide Full flag; third, to allow the loading of the Page

Address registers during initialization using the SFF

instruction. The full flag logic causes only the device

containing the first empty location to respond to Next Free

instructions such as “MOV NF ,CR,V”, which will move the

contents of the Comparand register to the first empty

location in a string of devices and set that location Valid,

so it will be available for the next automatic compare. W ith

devices connected as in Figure 1a, the /FF output of the

last device in a string provides a full indication for the

entire string.

IEEE 802.3/802.5 Format Mapping

To support the symmetrical mapping between the address

formats of IEEE 802.3 and IEEE 802.5, the WidePort

LANCAM provides a bit translation facility. Formally

expressed, the nth input bit, D(n), maps to the xth output

bit, Q(x), through the following expressions:

D(n) = Q(7-n) for 0 ≤ n ≤ 7,

D(n) = Q(23-n) for 8 ≤ n ≤ 15

D(n) = Q(39-n) for 16 ≤ n ≤ 23

D(n) = Q(55-n) for 24 ≤ n ≤ 31

Control Register bits CT10 and CT9 select whether to

persistently translate, or persistently not to translate, the

data written onto the 64-bit internal bus. The default

condition after a Reset command is not to translate the

incoming data. Figure 2 shows the bit mapping between

the two formats.

INITIALIZING THE WIDEPORT LANCAM

Initialization of the WidePort LANCAM is required to

configure the various registers on the device. Since a

Control register reset establishes the operating conditions

shown in T able 5, restoration of operating conditions better

suited for the application may be required after a reset,

whether using the Control Register reset, or the /RESET

pin. When the device powers up, the memory and registers

are in an unknown state, so the /RESET pin must be asserted

to place the device in a known state.

T able 6a (Standard mode) and Table 6b (Enhanced mode) show

when a device will respond to reads or writes and when it will

not, based on the state of /EC(int), the internal match condition,

and other control inputs. /EC is latched by the falling edge of

/E. /EC(int) is registered from the latched /EC signal off the

rising edge of /E, so it controls what happens in the next cycle,

as shown in Figure 6. When /EC is first taken LOW in a string

of LANCAM devices (and assuming the Device Select

registers are set to FFFFH), all devices will respond to that

command write or data write.

From then on the daisy chain will remain locked in each

subsequent cycle as long as /EC is held LOW on the falling

edge of /E in the current cycle. When the daisy chain is locked

in Standard mode, only the Highest-Priority Match device will

respond (See Case 6 of Table 6a). If, for example, all of the

CAM memory locations were empty , there would be no match,

and /MF would stay HIGH. Since none of the devices could

then be the Highest-Priority Match device, none will respond

to reads or writes until the daisy chain is unlocked by taking

/EC HIGH and asserting /E for a cycle.

If there is a match between the data in the Comparand

Highest-Priority Match device will respond to any cycle,

such as an associated data or Status Register read. If there

is not a match, then a NOP with /EC HIGH needs to be

inserted before issuing any new instructions, such as Write

to Next Free Address instruction to learn the data. Since

Next Free operations are controlled by the /FI–/FF daisy

chain, only the device with the first empty location will

respond. If an instruction is used to unlock the daisy chain

it will work only on the Highest-Priority Match device, if

one exists. If none exists, the instruction will have no effect

except to unlock the daisy chain. To read the Status

registers of specific devices when there is no match requires

the use of the TCO DS command to set DS=PA of each

device. Single chip systems can tie /EC HIGH and read the

Status register or the /MA and /MM pins to monitor match

conditions, as the daisy chain lock-out feature is not needed

in this configuration. This removes the need to insert a

NOP in the case of a no-match.

When the Control register is set to Enhanced mode, you

can continue to write data to the Comparand register or

issue a Move to Next Free Address instruction without

first having to issue a NOP with /EC HIGH to unlock the

daisy chain after a Compare cycle with no match, as

indicated in cases 4 and 5 of Table 6b. In Enhanced mode,

data write cycles as well as command write cycles are

enabled in all devices even when /EC is LOW. Exceptions

are data writes, moves, or VBC instructions involving HM,

OPERATIONAL CHARACTERISTICS

Continued

WidePort LANCAM® Family

Rev. 2 16

Notes:

1. Toggling the /RESET pin generates the same effect as this reset of the Control register, but good programming practice dictat es

a software reset for initialization to account for all possible prior conditions.

2. This instruction may be omitted for a single WidePort LANCAM application. The last SFF will cause the /FF pin in the last chip in

a daisy chain to go LOW. In a daisy chain, DS needs to be set equal to PA to read out a particular chip prior to a match condition.

3. T ypical WidePort LANCAM control environment: Enable match flag; Enable full flag; 32 CAM bits/32 RAM bits; Disable comparison

masking; and Enable address increment. This example translates to 8080H. See Table 9 for Control Register bit

assignments.

4. Setting the persistent source to the Memory at Highest-Priority match allows a compare operation to be followed by a read of the

associated data when a match is found. Note that the persistent destination is set to the Comparand register by the reset.

T able 7: Example Initialization Routine

Cycle Type

Command Write

Op-Code

TCO DS

TCO CT

TCO P A

SFF

•

TCO CT

TCO SC

SPS M@HM

DQ31–16

0A28H

0A00H

0A08H

0700H

0A00H

0A10H

0005H

DQ15–0

FFFFH

0000H

nnnnH

0000H

8080H

2808H

Comments

Target Device Select register and disable local device selection

Target Control register and reset

Target Page Address register and set page for cascaded operation

Set Full flag; allows access to next device (repeat previous cycle

plus this one for each device in chain)

Target Control register and reset Full flags, but not Page address

Target Control register and give initial values

Target Segment counter and set destination to only use upper

segment and source to only use lower segment

Set Persistent source to Memory at the Highest-Priority match

Notes

Data Bus

Setting Page Address Register V alues

In a vertically cascaded system, the user must set the

individual Page Address registers to unique values by

using the Page Address initialization mechanism. Each Page

Address register must contain a unique value to prevent

bus contention. This process allows individual device

selection. The Page Address register initialization works

as follows: W rites to Page Address registers are only active

for devices with /FI LOW and /FF HIGH. At initialization,

all devices are empty, thus the top device in the string will

respond to a TCO PA instruction, and load its PA register.

To advance to the next device in the string, a Set Full Flag

(SFF) instruction is used, which is also only active for the

device with /FI LOW and /FF HIGH. The SFF instruction

changes the first device’ s /FF to LOW , although the device

really is empty , which allows the next device in the string to

respond to the TCO PA instruction and load its PA register .

The initialization proceeds through the chain in a similar

manner filling all the PA registers in turn. Each device must

have a unique Page Address value stored in its PA register,

or contention will result. After all the PA registers are filled,

the entire string is reset through the Control register , which

does not change the values stored in the individual PA

registers. After the reset, the Device Select registers are

usually set to FFFFH to enable operation, in Case 1 of T able

6a. The Control registers and the Segment Control

registers are then set to their normal operating values

for the application.

Vertically Cascaded System Initialization

Table 7 shows an example of code that initializes a daisy-

chained string of WidePort LANCAM devices. The

initialization example shows how to set the Page Address

registers of each of the devices in the chain through the

use of the Set Full Flag instruction, and how the Control

registers and Segment counters of all the WidePort

LANCAM devices are set for a typical application. Each

Page Address register must contain a unique value (not

FFFFH) to prevent bus contention.

For typical daisy chain operation, data is loaded into the

Comparand registers of all the devices in a string

simultaneously by setting DS=FFFFH. Since reading is

prohibited when DS=FFFFH except for the device with a

match, for a diagnostic operation you need to select a

specific device by setting DS=PA for the desired device

to be able to read from it. Refer to Tables 6a and 6b for

preconditions for reading and writing.

Initialization for a single W idePort LANCAM is similar .

The Device Select register in this case is usually set to

equal the Page Address register for normal operations.

Also, the dedicated /MA flag output can be used instead

of /MF, allowing /EC to be tied HIGH.

OPERATIONAL CHARACTERISTICS

Continued

WidePort LANCAM® Family

Rev. 217

Instruction: Select Persistent Source (SPS)

Binary Op-Code: 0000 f000 0000 0sss*

f Address Field flag†

sss Selected source

This instruction selects a persistent source for data reads,

until another SPS instruction changes it or a reset occurs.

The default source after reset for Data Read cycles is the

Comparand register. Setting the persistent source to

M@aaaH loads the Address register with “aaaH,” and the

first access to that persistent source will be at aaaH, after

which the AR value increments or decrements as set in the

Control register. The SPS M@[AR] instruction does the

same except the current Address Register value is used.

Instruction: Select Persistent Destination (SPD)

Binary Op-Code: 0000 f001 mmdd dvvv*

f Address Field flag†

mm Mask Register select

ddd Selected destination

vvv Validity setting for Memory Location

destinations

This instruction selects a persistent destination for data

writes, which remains until another SPD instruction changes

it or a reset occurs. The default destination for Data Write

cycles is the Comparand register after a reset. When the

destination is the Comparand register or the memory array ,

the data written may be masked by either Mask Register 1

or Mask Register 2, so that only destination bits

corresponding to bits in the mask register set to 0 will be

modified. An automatic compare will occur after writing the

last segment of the Comparand or mask registers, but not

after writing to memory. Setting the persistent destination

to M@aaaH loads the Address register with “aaaH,” and

the first access to that persistent destination will be at aaaH,

after which the AR value increments or decrements as set

in the Control register . The SPD M@[AR] instruction does

the same except the current Address Register value is used.

Instruction: Temporary Command Override

(TCO)

Binary Op-Code: 0000 f010 00dd d000*

f Address Field flag†

ddd Register selected as source or

destination for only the next

Command Read or Write cycle

The TCO instruction temporarily redirects the DQ bus for

with the data on DQ15–0. If f=0, a subsequent Command

Read cycle reads the register contents through DQ15–0.

During register reads, DQ31–16 will contain the upper 16-

bits of the Status register, except in the case of a Page

Address register read where these bits are 0s. After the

access, subsequent Command Read or W rite cycles revert

to reading the Status register and writing to the Instruction

decoder . All registers except the Status, NF , PS, and PD are

available for write access. All registers are available for

read access. The complete Status register is only available

through a non-TCO Command Read access. Reading the

PS register also outputs the Device ID on bits 15–4, as

shown in T able 13.

Instruction: Data Move (MOV)

Binary Op-Code: 0000 f01 1 mmdd dsss or

0000 f01 1 mmdd dvss*

f Address Field flag†

mm Mask Register select

ddd Destination of data

sss Source of data

v Validity setting if destination is a

Memory location

The MOV instruction performs a 64-bit move of the data in

the selected source to the selected destination. If the source

or destination is aaaH, the Address register is set to “aaaH.”

For MOV instructions to or from aaaH or [AR], the Address

the move completes, as set in the Control register. Data

transfers between the Memory array and the Comparand

which correspond to bits in the selected mask register set

to 0 will be changed. A Memory location used as a

destination for a MOV instruction may be set to Valid or

left unchanged. If the source and destination are the same

Instruction: V alidity Bit Control (VBC)

Binary Op-Code: 0000 f100 00dd dvvv*

f Address Field flag†

dd d Destination of data

vv v Validity setting for Memory location

The VBC instruction sets the Validity bits at the selected

memory locations to the selected state. This feature can be

used to find all valid entries by using a repetitive sequence

of CMP V through a mask of all 1s followed by a VBC HM,

S. If the VBC target is aaaH, the Address register is set to

“aaaH.” For VBC instructions to or from aaaH or [AR], the

Address register will increment or decrement from that value

after the operation completes, as set in the Control register .

INSTRUCTION SET DESCRIPTIONS§

WidePort LANCAM® Family

Rev. 2 18

INSTRUCTION SET DESCRIPTIONS

Continued

Instruction: Compare (CMP)

Binary Op-Code: 0000 0101 0000 0vvv*

v vv Validity condition

A CMP V, S, or R instruction forces a Comparison of Valid,

Skipped, or Random entries against the Comparand register

through a mask register , if one is selected. During a CMP E

instruction, the compare is only done on the Validity bits

and all data bits are automatically masked.

Instruction: Special Instructions

Binary Op-Code: 0000 01 10 00dd drrr*

ddd Target resource

rrr Operation

These instructions are a special set for the A/L WidePort

LANCAMs to accommodate the added features over the

MU9C1485. Two alternate sets of configuration registers

can be selected by using the Select Foreground and Select

Background Registers instructions. These registers are the

Control, Segment Control, Address, Mask Register 1, and

the PS and PD registers. An RSC instruction resets the

Segment Control register count values for both the

Destination and Source counters to the original Start limits.

The Shift instructions shift the designated register one bit

right or left. The right and left limits for shifting are

determined by the CAM/RAM partitioning set in the Control

the example of a device set to 64 bits of CAM executing a

Shift Comparand Right instruction, bit 0 is moved to bit 63,

bit 1 is moved to bit 0, and bit 63 is moved to bit 62. For a

Shift Comparand Left instruction, bit 63 is moved to bit 0,

bit 0 is moved to bit 1, and bit 62 is moved to bit 63. MR2

acts as a sliding mask, where for a Shift Right instruction

bit 1 is moved to bit 0, while bit 0 “falls off the end,” and bit

63 is replicated to bit 62. For a Shift Mask Left instruction,

bit 0 is replicated to bit 1, bit 62 is moved to bit 63, and bit 63

"falls off the end.” With shorter width CAM fields, the

bit limits on the right or left move to match the width of

CAM field.

Instruction: Set Full Flag (SFF)

Binary Op-Code: 0000 01 11 0000 0000*

The SFF instruction is a special instruction used to force

the Full flag LOW to permit setting the Page Address

Instruction: No Operation (NOP)

Binary Op-Code: 0000 001 1 0000 0000

The NOP (No-OP) belongs to the MOV instructions, where

a register is moved to itself. No change occurs within the

device. This instruction is useful in unlocking the daisy

chain in Standard mode.

Notes:

§Instruction cycle lengths given in Table 8.

* Instruction Op-Codes are loaded on the DQ31–16 lines.

†If f=1, the instruction requires an absolute address

(or register contents for TCOs) to be supplied onthe

DQ15–0 lines. Supplied addresses will update the

Address register to the “aaaH” value supplied. After

an operation involving M@[AR] or M@aaaH, the

Address register will be incremented or decremented

depending on the setting in the Control register.

WidePort LANCAM® Family

Rev. 219

INSTRUCTION SET SUMMARY

MNEMONIC FORMA T

INS dst,src[msk],val

INS: Instruction mnemonic

dst: Destination of the data

src: Source of the data

msk:Mask register used

val: Validity condition set at the location written

Instruction: Select Persistent Source

Operation Mnemonic Op-Code

Comparand Register SPS CR 0000H

Mask Register 1 SPS MR1 0001H

Mask Register 2 SPS MR2 0002H

Memory Array at Addr. Reg. SPS M@[AR] 0004H

Memory Array at Address SPS M@aaaH 0804H

Mem. at Highest-Prio. Match SPS M@HM 0005H

Instruction: Select Persistent Destination

Operation Mnemonic Op-Code

Comparand Register SPD CR 0100H

Masked by MR1 SPD CR[MR1] 0140H

Masked by MR2 SPD CR[MR2] 0180H

Mask Register 1 SPD MR1 0108H

MaskRegister 2 SPD MR2 0110H

Mem. at Addr. Reg. set Valid SPD M@[AR],V 0124H

Masked by MR1 SPD M@[AR][MR1],V 0164H

Masked by MR2 SPD M@[AR][MR2],V 01A4H

Mem. at Addr. Reg. set Empty SPD M@[AR],E 0125H

Masked by MR1 SPD M@[AR][MR1],E 0165H

Masked by MR2 SPD M@[AR][MR2],E 01A5H

Mem. at Addr. Reg. set Skip SPD M@[AR],S 0126H

Masked by MR1 SPD M@[AR][MR1],S 0166H

Masked by MR2 SPD M@[AR][MR2],S 01A6H

Mem. at Addr . Reg. set Random SPD M@[AR],R 0127H

Masked by MR1 SPD M@[AR][MR1],R 0167H

Masked by MR2 SPD M@[AR][MR2],R 01A7H

Memory at Address set Valid SPD M@aaaH,V 0924H

Masked by MR1 SPD M@aaaH[MR1],V 0964H

Masked by MR2 SPD M@aaaH[MR2],V 09A4H

Memory at Addr. set Empty SPD M@aaaH,E 0925H

Masked by MR1 SPD M@aaaH[MR1],E 0965H

Masked by MR2 SPD M@aaaH[MR2],E 09A5H

Memory at Address set Skip SPD M@aaaH,S 0926H

Masked by MR1 SPD M@aaaH[MR1],S 0966H

Masked by MR2 SPD M@aaaH[MR2],S 09A6H

Mem. at Address set Random SPD M@aaaH,R 0927H

Masked by MR1 SPD M@aaaH[MR1],R 0967H

Masked by MR2 SPD M@aaaH[MR2],R 09A7H

Mem. at Highest-Prio. Match, V alid SPD M@HM,V 012CH

Masked by MR1 SPD M@HM[MR1],V 016CH

Masked by MR2 SPD M@HM[MR2],V 01ACH

Instruction: Select Persistent Destination

Cont.

Operation Mnemonic Op-Code

Mem. at Highest-Prio. Match, Emp. SPD M@HM,E 012DH

Masked by MR1 SPD M@HM[MR1],E 016DH

Masked by MR2 SPD M@HM[MR2],E 01ADH

Mem. at Highest-Prio. Match, Skip SPD M@HM,S 012EH

Masked by MR1 SPD M@HM[MR1],S 016EH

Masked by MR2 SPD M@HM[MR2],S 01AEH

Mem. at High.-Prio. Match, Random SPD M@HM,R 012FH

Masked by MR1 SPD M@HM[MR1],R 016FH

Masked by MR2 SPD M@HM[MR2],R 01AFH

Mem. at Next Free Addr., Valid SPD M@NF ,V 0134H

Masked by MR1 SPD M@NF[MR1],V 0174H

Masked by MR2 SPD M@NF[MR2],V 01B4H

Mem. at Next Free Addr., Empty SPD M@NF,E 0135H

Masked by MR1 SPD M@NF[MR1],E 0175H

Masked by MR2 SPD M@NF[MR2],E 01B5H

Mem. at Next Free Addr., Skip SPD M@NF,S 0136H

Masked by MR1 SPD M@NF[MR1],S 0176H

Masked by MR2 SPD M@NF[MR2],S 01B6H

Mem. at Next Free Addr ., Random SPD M@NF ,R 0137H

Masked by MR1 SPD M@NF[MR1],R 0177H

Masked by MR2 SPD M@NF[MR2],R 01B7H

Instruction: T emporary Command Override

Operation Mnemonic Op-Code

Control Register TCO CT 0n00H

Page Address Register TCO P A 0n08H

Segment Control Register TCO SC 0n10H