SAA1064T/N2,118-CUT TAPE\"\" - NXP SEMICONDUCTORS

DATA SH EET

Product speciﬁcation

File under Integrated Circuits, IC01 February 1991

INTEGRATED CIRCUITS

SAA1064

4-digit LED-driver with I2C-Bus

interface

February 1991 2

Philips Semiconductors Product speciﬁcation

4-digit LED-driver with I2C-Bus interface SAA1064

GENERAL DESCRIPTION

The LED-driver is a bipolar integrated circuit made in an

I2L compatible 18 volts process. The circuit is especially

designed to drive four 7-segment LED displays with

decimal point by means of multiplexing between two pairs

of digits. It features an I2C-Bus slave transceiver interface

with the possibility to program four different SLAVE

ADDRESSES, a POWER RESET flag, 16 current sink

OUTPUTS, controllable by software up to 21 mA, two

multiplex drive outputs for common anode segments, an

on-chip multiplex oscillator, control bits to select static,

dynamic and blank mode, and one bit for segment test.

QUICK REFERENCE DATA

Note

1. The positive current is defined as the conventional current flow into a device (sink current).

PACKAGE OUTLINE

SAA1064: 24-lead DIL; plastic with internal heat spreader (SOT101B); SOT101-1; 1996 August 30.

SAA1064T: 24-lead mini-pack; plastic (SO-24; SOT137A); SOT137-1; 1996 August 30.

PARAMETER CONDITIONS SYMBOL MIN. TYP. MAX. UNIT

Supply voltage VEE = 0 V VCC 4.5 5 15 V

Supply current all outputs OFF VCC = 5 V ICC(1) 7 9.5 14 mA

Total power dissipation

24-lead DIL (SOT101B) Ptot −−1000 mW

24-lead DIL SO (SOT137A) Ptot −−500 mW

Operating ambient

temperature range Tamb −40 −+85 °C

February 1991 3

Philips Semiconductors Product speciﬁcation

4-digit LED-driver with I2C-Bus interface SAA1064

Fig.1 Block diagram.

February 1991 4

Philips Semiconductors Product speciﬁcation

4-digit LED-driver with I2C-Bus interface SAA1064

PINNING

SYMBOL PIN DESCRIPTION

ADR 1 I2C-Bus slave address input

CEXT 2 external control

P8 to P1 3-10 segment output

MX1 11 multiplex output

VEE 12 ground

VCC 13 positive supply

MX2 14 multiplex output

P9 to P16 15-22 segment output

SDA 23 I2C-Bus serial data line

SCL 24 I2C-Bus serial clock line

Fig.2 Pinning diagram.

February 1991 5

Philips Semiconductors Product speciﬁcation

4-digit LED-driver with I2C-Bus interface SAA1064

FUNCTIONAL DESCRIPTION

Address pin ADR

Four different slave addresses can be chosen by connecting ADR either to VEE, 3/8 VCC, 5/8 VCC or VCC. This results in

the corresponding valid addresses HEX 70, 72, 74 and 76 for writing and 71, 73, 75 and 77 for reading. All other

addresses cannot be acknowledged by the circuit.

S = start condition A1, A0 = programmable address bits

P = stop condition SC SB SA = subaddress bits

A = acknowledge C6 to C0 = control bits

X = don’t care PR = POWER RESET ﬂag

Fig.3 I2C-Bus format.

a. READ mode.

b. WRITE mode.

February 1991 6

Philips Semiconductors Product speciﬁcation

4-digit LED-driver with I2C-Bus interface SAA1064

Status byte

Only one bit is present in the status byte, the POWER RESET flag. A logic 1 indicates the occurence of a power failure

since the last time it was read out. After completion of the READ action this flag will be set to logic 0.

Subaddressing

The bits SC, SB and SA form a pointer and determine to which register the data byte following the instruction byte will

be written. All other bytes will then be stored in the registers with consecutive subaddresses. This feature is called

Auto-Increment (AI) of the subaddress and enables a quick initialization by the master.

The subaddress pointer will wrap around from 7 to 0.

The subaddresses are given as follows:

Control bits (see Fig.4)

The control bits C0 to C6 have the following meaning:

Note

1. At a current determined by C4, C5 and C6.

Data

A segment is switched ON if the corresponding data bit is logic 1. Data bits D17 to D10 correspond with digit 1, D27 to

D20 with digit 2, D37 to D30 with digit 3 and D47 to D40 with digit 4.

The MSBs correspond with the outputs P8 and P16, the LSBs with P1 and P9. Digit numbers 1 to 4 are equal to their

subaddresses (hex) 1 to 4.

SC SB SA SUB-ADDRESS FUNCTION

0 0 0 00 control register

0 0 1 01 digit 1

0 1 0 02 digit 2

0 1 1 03 digit 3

1 0 0 04 digit 4

1 0 1 05 reserved, not used

1 1 0 06 reserved, not used

1 1 1 07 reserved, not used

C0 = 0 static mode, i.e. continuous display of digits 1 and 2

C0 = 1 dynamic mode, i.e. alternating display of digit 1 + 3 and 2 + 4

C1 = 0/1 digits 1 + 3 are blanked/not blanked

C2 = 0/1 digits 2 + 4 are blanked/not blanked

C3 = 1 all segment outputs are switched-on for segment test(1)

C4 = 1 adds 3 mA to segment output current

C5 = 1 adds 6 mA to segment output current

C6 = 1 adds 12 mA to segment output current

February 1991 7

Philips Semiconductors Product speciﬁcation

4-digit LED-driver with I2C-Bus interface SAA1064

SDA, SCL

The SDA and SCL I/O meet the I2C-Bus specification. For protection against positive voltage pulses on these inputs

voltage regulator diodes are connected to VEE. This means that normal line voltage should not exceed 5,5 volt. Data will

be latched on the positive-going edge of the acknowledge related clock pulse.

Power-on reset

The power-on reset signal is generated internally and sets all bits to zero, resulting in a completely blanked display. Only

the POWER RESET flag is set.

External Control (CEXT)

With a capacitor connected to pin 2 the multiplex frequency can be set (see Fig.5). When static this pin can be connected

to VEE or VCC or left floating since the oscillator will be switched off.

Segment outputs

The segment outputs P1 to P16 are controllable current-sink sources. They are switched on by the corresponding data

bits and their current is adjusted by control bits C4, C5 and C6.

Multiplex outputs

The multiplex outputs MX1 and MX2 are switched alternately in dynamic mode with a frequency derived from the

clock-oscillator. In static mode MX1 is switched on. The outputs consist of an emitter-follower, which can be used to drive

the common anodes of two displays directly provided that the total power dissipation of the circuit is not exceeded. If this

occurs external transistors should be connected to pins 11 and 14 as shown in Fig.5.

February 1991 8

Philips Semiconductors Product speciﬁcation

4-digit LED-driver with I2C-Bus interface SAA1064

RATINGS

Limiting values in accordance with the Absolute Maximum System (IEC 134)

THERMAL RESISTANCE

PARAMETER CONDITIONS SYMBOL MIN. MAX. UNIT

Supply voltage (pin 13) VEE = 0 V VCC −0.5 18 V

Supply current (pin 13) ICC −50 200 mA

Total power dissipation

24-lead DIL (SOT101B) Ptot 1000 mW

24-lead SO (SO137A) Ptot 500 mW

SDA, SCL voltages VEE = 0 V V23, 24 −0.5 5.9 V

Voltages ADR-MX1 and MX2-P16 VEE = 0 V V1-11, V14-22 −0.5 VCC + 0.5 V

Input/output current all pins outputs OFF ±II/O −10 mA

Operating ambient

temperature range Tamb −40 +85 °C

Storage temperature range Tstg −55 +150 °C

From crystal to ambient

24-lead DIL Rth j-a 35 K/W

24-lead SO (on ceramic substrate) Rth j-a 75 K/W

24-lead SO (on printed circuit board) Rth j-a 105 K/W

February 1991 9

Philips Semiconductors Product speciﬁcation

4-digit LED-driver with I2C-Bus interface SAA1064

CHARACTERISTICS

VCC = 5 V; Tamb = 25 °C; voltages are referenced to ground (VEE = 0 V); unless otherwise speciﬁed

PARAMETER CONDITIONS SYMBOL MIN. TYP. MAX. UNIT

Supply

Supply voltage (pin 13) VCC 4,5 5,0 15 V

Supply current all outputs OFF

VCC = 5 V ICC 7,0 9,5 14,0 mA

Power dissipation all outputs OFF Pd−50 −mW

SDA; SCL (pins 23 and 24)

Input voltages V23,24 0−5,5 V

Logic input voltage LOW VIL(L) −−1,5 V

Logic input voltage HIGH VIH(L) 3,0 −−V

Input current LOW V23,24 = VEE −IIL −−10 µA

Input current HIGH V23,24 = VCC IIH −−10 µA

SDA

Logic output voltage LOW IO= 3 mA VOL(L) −−0,4 V

Output sink current ISDA 3−−mA

Address input (pin 1)

Input voltage

programmable address bits:

A0 = 0; A1 = 0 V1VEE −3/16VCC V

A0 = 1; A1 = 0 V15/16VCC 3/8VCC 7/16VCC V

A0 = 0; A1 = 1 V19/16VCC 5/8VCC 11/16VCC V

A0 = 1; A1 = 1 V113/16VCC −VCC V

Input current LOW V1= VEE −I1−−10 µA

Input current HIGH V1= VCC I1−−10 µA

External control (CEXT) pin 2

Switching level input

Input voltage LOW VIL −−V

CC−3,3 V

Input voltage HIGH VIH VCC−1,5 −−V

Input current V2= 2 V I2−140 −160 −180 µA

V2= 4 V I2140 160 180 µA

February 1991 10

Philips Semiconductors Product speciﬁcation

4-digit LED-driver with I2C-Bus interface SAA1064

* Value to be fixed.

Segment outputs

(P8 to P1; pins 3 to 10)

P9 to P16; pins 15 to 22)

Output voltages IO= 15 mA VO−−0.5 V

Output leakage current HIGH VO= VCC = 15 V ILO −−±10 µA

Output current LOW

All control bits (C4, C5

and C6) are HIGH VOL = 5 V IOL 17.85 21 25.2 mA

Contribution of:

control bit C4 IO2.55 3.0 3.6 mA

control bit C5 IO5.1 6.0 7.2 mA

control bit C6 IO10.2 12.0 14.4 mA

Relative segment output

current accuracy

with respect to highest value ∆IO−−7.5 %

Multiplex 1 and 2 (pins 11

and 14)

Maximum output voltage

(when ON) −IMPX = 50 mA VMPX VCC−1.5 −−V

Maximum output current HIGH

(when ON) VMPX = 2 V −IMPX 50 −110 mA

Maximum output current LOW

(when OFF) VO= 2 V +IMPX 50 70 110 µA

Multiplex output period CEXT = 2.7 nF TMPX 5−10 ms

Multiplexed duty factor −48.4 −%

PARAMETER CONDITIONS SYMBOL MIN. TYP. MAX. UNIT

February 1991 11

Philips Semiconductors Product speciﬁcation

4-digit LED-driver with I2C-Bus interface SAA1064

Fig.4 Timing diagram.

February 1991 12

Philips Semiconductors Product speciﬁcation

4-digit LED-driver with I2C-Bus interface SAA1064

APPLICATION INFORMATION

Fig.5 Dynamic mode application diagram.

February 1991 13

Philips Semiconductors Product speciﬁcation

4-digit LED-driver with I2C-Bus interface SAA1064

Fig.6 Static mode application diagram.

February 1991 14

Philips Semiconductors Product speciﬁcation

4-digit LED-driver with I2C-Bus interface SAA1064

POWER DISSIPATION

The total maximum power dissipation of the SAA1064 is made up by the following parts:

1. Maximum dissipation when none of the outputs are programmed (continuous line in Fig.7).

2. Maximum dissipation of each programmed output. The dashed line in Fig.7 visualises the dissipation when all the

segments are programmed (max. 16 in the static, and max. 32 in the dynamic mode). When less segments are

programmed one should take a proportional part of the maximum value.

3. Maximum dissipation of the programmed segment drivers which can be expressed as:

Padd = VO×IO×N.

Under no conditions the total maximum dissipation (500 mW for the SO and 1000 mW for the DIL package) should be

exceeded.

Where: Padd = The additional power dissipation of the segment drivers

VO= The low state segment driver output voltage

IO= The programmed segment output current

N = The number of programmed segments in the static mode, or half the number of

programmed segment drivers in the dynamic mode.

Example: VCC =5 V

O= 0.25 V

IO= 12 mA

24 programmed segments in dynamic mode

Ptot =P

2+P

= 75 mW + (50 * 24/32) mW +(0.25 * 12.10−3* 12) mW

= 148.5 mW

February 1991 15

Philips Semiconductors Product speciﬁcation

4-digit LED-driver with I2C-Bus interface SAA1064

handbook, full pagewidth

15.0

750

dissipation

(mW)

00 2.5 12.5 VCC (V)

500

250

7.55.0 10.0

(1)

(2)

MEA104

Fig.7 SAA1064 power dissipation as a function of supply voltage.

(1) All outputs programmed (no segment current sink).

(2) Outputs not programmed.

February 1991 16

Philips Semiconductors Product speciﬁcation

4-digit LED-driver with I2C-Bus interface SAA1064

PACKAGE OUTLINES

UNIT A

max. 1 2 b1cD E e M

REFERENCES

OUTLINE

VERSION EUROPEAN

PROJECTION ISSUE DATE

IEC JEDEC EIAJ

inches

DIMENSIONS (inch dimensions are derived from the original mm dimensions)

SOT101-1 92-11-17

95-01-23

min. A

max. bw

1.7

1.3 0.53

0.38 0.32

0.23 32.0

31.4 14.1

13.7 3.9

3.4 0.252.54 15.24 15.80

15.24 17.15

15.90 2.25.1 0.51 4.0

0.066

0.051 0.021

0.015 0.013

0.009 1.26

1.24 0.56

0.54 0.15

0.13 0.010.10 0.60 0.62

0.60 0.68

0.63 0.0870.20 0.020 0.16

051G02 MO-015AD

(e )

seating plane

pin 1 index

0 5 10 mm

scale

Note

1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.

max.

(1)

(1)(1)

DIP24: plastic dual in-line package; 24 leads (600 mil) SOT101-1

February 1991 17

Philips Semiconductors Product speciﬁcation

4-digit LED-driver with I2C-Bus interface SAA1064

UNIT A

max. A1A2A3bpcD

(1) E(1) (1)

ELL

pQZ

ywv θ

REFERENCES

OUTLINE

VERSION EUROPEAN

PROJECTION ISSUE DATE

IEC JEDEC EIAJ

inches

2.65 0.30

0.10 2.45

2.25 0.49

0.36 0.32

0.23 15.6

15.2 7.6

7.4 1.27 10.65

10.00 1.1

1.0 0.9

0.4 8

0.25 0.1

DIMENSIONS (inch dimensions are derived from the original mm dimensions)

Note

1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.

1.1

0.4

SOT137-1

detail X

vMA

(A )

0.25

075E05 MS-013AD

pin 1 index

0.10 0.012

0.004 0.096

0.089 0.019

0.014 0.013

0.009 0.61

0.60 0.30

0.29 0.050

1.4

0.055

0.419

0.394 0.043

0.039 0.035

0.016

0.01

0.25

0.01 0.004

0.043

0.016

0.01

0 5 10 mm

scale

SO24: plastic small outline package; 24 leads; body width 7.5 mm SOT137-1

95-01-24

97-05-22

February 1991 18

Philips Semiconductors Product speciﬁcation

4-digit LED-driver with I2C-Bus interface SAA1064

SOLDERING

Introduction

There is no soldering method that is ideal for all IC

packages. Wave soldering is often preferred when

through-hole and surface mounted components are mixed

on one printed-circuit board. However, wave soldering is

not always suitable for surface mounted ICs, or for

printed-circuits with high population densities. In these

situations reflow soldering is often used.

This text gives a very brief insight to a complex technology.

A more in-depth account of soldering ICs can be found in

our

“IC Package Databook”

(order code 9398 652 90011).

DIP

SOLDERING BY DIPPING OR BY WAVE

The maximum permissible temperature of the solder is

260 °C; solder at this temperature must not be in contact

with the joint for more than 5 seconds. The total contact

time of successive solder waves must not exceed

5 seconds.

The device may be mounted up to the seating plane, but

the temperature of the plastic body must not exceed the

specified maximum storage temperature (Tstg max). If the

printed-circuit board has been pre-heated, forced cooling

may be necessary immediately after soldering to keep the

temperature within the permissible limit.

REPAIRING SOLDERED JOINTS

Apply a low voltage soldering iron (less than 24 V) to the

lead(s) of the package, below the seating plane or not

more than 2 mm above it. If the temperature of the

soldering iron bit is less than 300 °C it may remain in

contact for up to 10 seconds. If the bit temperature is

between 300 and 400 °C, contact may be up to 5 seconds.

REFLOW SOLDERING

Reflow soldering techniques are suitable for all SO

packages.

Reflow soldering requires solder paste (a suspension of

fine solder particles, flux and binding agent) to be applied

to the printed-circuit board by screen printing, stencilling or

pressure-syringe dispensing before package placement.

Several techniques exist for reflowing; for example,

thermal conduction by heated belt. Dwell times vary

between 50 and 300 seconds depending on heating

method. Typical reflow temperatures range from

215 to 250 °C.

Preheating is necessary to dry the paste and evaporate

the binding agent. Preheating duration: 45 minutes at

45 °C.

WAVE SOLDERING

Wave soldering techniques can be used for all SO

packages if the following conditions are observed:

•A double-wave (a turbulent wave with high upward

pressure followed by a smooth laminar wave) soldering

technique should be used.

•The longitudinal axis of the package footprint must be

parallel to the solder flow.

•The package footprint must incorporate solder thieves at

the downstream end.

During placement and before soldering, the package must

be fixed with a droplet of adhesive. The adhesive can be

applied by screen printing, pin transfer or syringe

dispensing. The package can be soldered after the

adhesive is cured.

Maximum permissible solder temperature is 260 °C, and

maximum duration of package immersion in solder is

10 seconds, if cooled to less than 150 °C within

6 seconds. Typical dwell time is 4 seconds at 250 °C.

A mildly-activated flux will eliminate the need for removal

of corrosive residues in most applications.

REPAIRING SOLDERED JOINTS

Fix the component by first soldering two diagonally-

opposite end leads. Use only a low voltage soldering iron

(less than 24 V) applied to the flat part of the lead. Contact

time must be limited to 10 seconds at up to 300 °C. When

using a dedicated tool, all other leads can be soldered in

one operation within 2 to 5 seconds between

270 and 320 °C.

February 1991 19

Philips Semiconductors Product speciﬁcation

4-digit LED-driver with I2C-Bus interface SAA1064

DEFINITIONS

LIFE SUPPORT APPLICATIONS

These products are not designed for use in life support appliances, devices, or systems where malfunction of these

products can reasonably be expected to result in personal injury. Philips customers using or selling these products for

use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such

improper use or sale.

PURCHASE OF PHILIPS I2C COMPONENTS

Data sheet status

Objective speciﬁcation This data sheet contains target or goal speciﬁcations for product development.

Preliminary speciﬁcation This data sheet contains preliminary data; supplementary data may be published later.

Product speciﬁcation This data sheet contains ﬁnal product speciﬁcations.

Limiting values

Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or

more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation

of the device at these or at any other conditions above those given in the Characteristics sections of the speciﬁcation

is not implied. Exposure to limiting values for extended periods may affect device reliability.

Application information

Where application information is given, it is advisory and does not form part of the speciﬁcation.

Purchase of Philips I2C components conveys a license under the Philips’ I2C patent to use the

components in the I2C system provided the system conforms to the I2C specification defined by

Philips. This specification can be ordered using the code 9398 393 40011.