New Product Single-phase Power Controller G3PW High-precision Control with Easy Setup * Precise heater burnout detection. * Set value and present value monitoring with indicators. * Phase control or optimum cycle control. * RS-485 communications to set manipulated variables and monitor load current. * Total run time monitoring. * Output modes for phase control: proportional to phase angle, proportional to voltage, proportional to square voltage, and constant-current control. * Application with various loads: constant load resistance, variable load resistance. * UL, and IEC/EN (TUV) certified. For the most recent information on models that have been certified for safety standards, refer to your OMRON website. Model Number Structure Model Number Legend G3PW-A2@@E@-@-@@@ 1 2 3 4 5 6 7 8 1. Basic model G3PW: Power Controller 2. Degree of protection A: Panel-mounting/Closed wallmounting 3. Voltage class 2: 200 VAC 4. Maximum rated current 20: 20 A 45: 45 A 60: 60 A 5. Power supply type E: Single-phase power supply 6. Current control U: Standard Model (no constant-current control) C: Constant-current Model 7. Control terminal block C: Screwless clamp terminal block S: Terminal block with small slotted screws 8. RS-485 communications Blank: Communications not supported. FLK: Communications supported. Ordering Information List of Models Number of phases Control terminal block Type Capacity Heater burnout detection Communications No No 20 A Standard Screwless clamp terminal block Constant current Single-phase G3PW-A220EU-C 45 A G3PW-A260EU-C 20 A G3PW-A220EC-C-FLK 45 A 60 A 45 A Yes Yes Constant current G3PW-A220EU-S No No G3PW-A245EU-S G3PW-A260EU-S 20 A 45 A G3PW-A245EC-C-FLK G3PW-A260EC-C-FLK 100 to 240 VAC 60 A Terminal block with small slotted screws G3PW-A245EU-C 60 A 20 A Standard Model number G3PW-A220EC-S-FLK Yes 60 A Yes G3PW-A245EC-S-FLK G3PW-A260EC-S-FLK Accessories (Order Separately) Name Resistive value Display Model External Variable Resistor 2 k 202 G32X-V2K 1 G3PW Ratings/Specifications Model Item Constant-current Models G3PW-A2@@EC-@-FLK Control method Analog input: Phase control or optimum cycle control Voltage ON/OFF input: ON/OFF control Maximum load capacity * Phase control: Linear (resistive) load, transformer primary-side control (flux density: 1.25 T max.) * Optimum cycle control: Linear (resistive) load (Transformer primaryside control is not supported.) Analog input Output mode Proportional to phase angle, proportional to square voltage, proportional to voltage Optimum cycle control Optimum cycle control (Output is switched to 100% or 0% each half cycle.) Proportional to voltage control Phase Single Rated voltage 100 to 240 VAC Operating voltage range -15% to +10% Power supply frequency 50/60 Hz Power supply frequency fluctuation 3 Hz 5 VA max. (Control power D-E) Power consumption Load current range Inrush current resistance I 2t -A220E@ 1 to 20 A -A245E@ 1 to 45 A -A260E@ 1 to 60 A -A220E@ 220 A (60 Hz, 1 cycle) -A245E@ 440 A (60 Hz, 1 cycle) -A260E@ 440 A (60 Hz, 1 cycle) -A220E@ 400A2s (1 cycle) -A245E@ 1,600A2s (1 cycle) -A260E@ 1,600A2s (1 cycle) Output voltage adjustable range Input signal for control Output value setting range Proportional to phase angle, proportional to square voltage, proportional to voltage, constant-current control Phase control Voltage ON/ ON/OFF control OFF input 0% to 98% Analog input 4 to 20 mA DC (input impedance: 100 ) or 1 to 5 VDC (input impedance: 30.1 k) Voltage ON/OFF Input 5 VDC (input impedance: 30.1 k) External main setting Specified Variable Resistor: G32X-V2K (2 k, 2 W) External duty setting Specified Variable Resistor: G32X-V2K (2 k, 2 W) Main setting 0.0% to 100% Base-up value 0.0% to 100% (Default: 0.0%) Upper/lower limits Output upper limit: 0.0% to 100% (Default: 100%) Output lower limit: 0.0% to 100% (Default: 0.0%) Duty setting Duty setting = Internal duty setting x External duty setting Internal duty setting range (set using front-panel keys or communications): 0% to 100% (Default: 100%) External duty setting range (set using external variable resistor): 0% to 100% (Default: 100%) Soft-start up time and soft-start down time 0.0 to 99.9 s (Default: 0.5 s) Either phase control or optimum cycle control can be used. Constant current --- Current fluctuation: 2% FS Load current upper limit --- 0.0 to 66.0 A (Default: 0.0 = OFF) Overcurrent detection time: 500 ms max. Current detection Heater burnout alarm Current transformer (CT) --- Built-in Current detection accuracy --- 10% FS of rated current Minimum detected load current --- 1A Detection method --- According to heater resistance (with heater resistance teaching and Heater Burnout Threshold parameter) Note: The accuracy of heater burnout detection will be lower for heaters for which the resistance significantly changes depending on the temperature. Setting range for heater burnout detection --- 1% to 100% (Default: 100%) Burnout detection accuracy --- 10% FS at rated current (Not applicable to loads with variable resistance.) Burnout detection output lower limit --- Detects a burnout at or above the specified output value. 0.0% to 100% (Default: 0.0%) Number of alarms for heater burnout detection --- 0 to 999 (Default: 150) --- Burnout of 1 of 10 heater elements can be detected (at the rated current). Multiple heater burnout detections Event inputs 2 Standard Models G3PW-A2@@EU-@ Number of event inputs 2 event inputs Event input 1: The function of the event input can be changed with a parameter setting in the initial setting level. The event input can be used for one of the following functions. * Switching the main setting between automatic and manual operation. * Switching between phase control and optimum cycle control. Event input 2: Alarm reset Contact input conditions ON: 1 k max., OFF: 100 k min. Non-contact input conditions ON residual voltage: 1.0 V max., OFF leakage current: 0.1 mA max. Current flow Approx. 1.1 mA (per input) Output voltage 5 VDC G3PW Model Item Number of alarm outputs Alarm outputs Standard Models Constant-current Models G3PW-A2@@EU-@ G3PW-A2@@EC-@-FLK 2 alarm outputs * Alarm output 1: ALARM1 (caution) * Alarm output 2: ALARM2 (warning) Open-collector outputs (Individual common) Maximum operating voltage 30 VDC Maximum load current 50 mA Maximum residual voltage 1.5 V Maximum leakage current 0.4 mA Serial communications Overcurrent detection --- One RS-485 port: CompoWay/F slave function (See note.) Note: Connection is possible to a Basic Unit in an EJ1 Modular Temperature Controller. Parameters can be set and monitored from the CX-Thermo Support Software running on a computer that is connected to the EJ1 End Unit. --- Rated current x 120% min., within 250 cycles SSR failure detection An error is detected within 3 seconds after an SSR failure. * Phase angle range for SSR short-circuit failure detection: 0% to 72% * Phase angle range for SSR open failure detection: 28% to 100% Output ON voltage drop 1.6 Vrms (at 100 % output on) Power supply frequency error Not within 47 to 63 Hz Leakage current 10 mA max. (100/110 VAC), 20 mA max. (200/220 VAC) Insulation resistance 100 M min. (at 500 VDC) Dielectric strength 2,500 VAC at 50/60 Hz for 1 min between charged parts and noncharged parts Vibration resistance 10 to 55 to 10 Hz, 100 m/s2 Shock resistance 300 m/s2 Ambient operating temperature -15C to 55C (with no icing or condensation) Ambient operating humidity 5% to 95% Storage temperature -25C to 65C (with no icing or condensation) Weight G3PW-A220E@-@-@@@: 1.0 kg max. G3PW-A245E@-@-@@@: 1.9 kg max. G3PW-A260E@-@-@@@: 1.9 kg max. Safety Standards UL508 CSA C22.2 No.14 EN60947-4-3 (pollution degree 2, overvoltage category II) EMC Directives EMI EN60947-1 EN60947-4-3 EMS EN60947-1 EN60947-4-3 Applicable Standards Fuses (recommended models for external connection) Recommended models Super-rapid Fuse (Fuji Electric) Type Fast-acting fuses * For 20 A CR6L-20/UL For 45 A CR6L-50/UL For 60 A CR6L-75/UL Fuse Holder (Fuji Electric) CMS-4 CMS-5 * Ask your OMRON representative for UL certified products. Time-delay fuses specifications Type Specification Time-delay fuses 250 VAC, 2 A 3 G3PW Nomenclature and Operations Level indicators 7-segment display Reset/event indicator Monitoring indicators LVL Key UP Key Communications indicator DOWN Key ENT/RST Key Control terminal block Command input and power supply terminal block (with cover) 1. 1 to 5-V/0 or 5-V input 2. 4 to 20-mA input 3. Current/voltage input COM 4. 100 to 240 VAC 5. 100 to 240 VAC Protective cover (removable) Load terminal block (under protective cover) 100 to 240 VAC Level Indicators Indicator Description ADJ Lit when in the adjustment level. SET Lit when in the initial setting level. EV Lit when an external contact reset input or an event input is ON. Monitoring Indicators Indicator Description %(IN) Lit when the input value is monitored in the monitor level. %(DUTY) Lit when the duty value is monitored in the monitor level. %(OUT) Lit when the output value is monitored in the monitor level. %(PHASE) Lit when the phase angle is monitored in the monitor level. A Lit when the current is monitored in the monitor level. Communications Indicator Indicator Description COMM Lit when the serial communications are in progress. Operation Keys Key symbol Name Enabling condition LVL (level) Key ENT/RST (enter/reset) Key Set value display Set value change and entry Error reset UP Key DOWN Key 4 Description Level Changes Monitor level Adjustment level Changing from monitor level to adjustment level or Monitor level Initial setting level from monitor level to initial setting level is possible Software is reset when moving from the initial set- even when an error occurs. ting level to monitor level. Set value change Monitor item/set value number change In the monitor level, the ENT/RST Key functions as a Reset Key only when an error occurs. (It does not function as a Reset Key when there is no error.) --- G3PW Engineering Data Ambient Temperature G3PW-A260E@ Load current (%) Load current (%) Current and Temperature Characteristics G3PW-A220E@/A245E@ 100 80 100 A 80 B 60 60 40 40 20 20 0 10 20 30 40 50 55 60 0 10 20 30 Ambient temperature (C) 40 A : Installation with 20 mm between Power Controllers B : Close mounting 50 55 60 Ambient temperature (C) Note: 1. The ambient operating temperature range is -15 to 55C, but take the following considerations into account. When the ambient temperature exceeds 40C, reduce the maximum load current as shown below. 2. At least 20 mm must be provided on the left and right sides of the G3PW-A260E@. If you must use side-by-side mounting, then reduce the maximum load current when the ambient temperature is over 30C. 3. Certification for safety standards was obtained with a mounting interval of 20 mm. 4. Leave sufficient space for ventilation. 5. Do not install the Power Controller above devices that generate significant amounts of heat, such as heaters, transformers, and highcapacity resistors. 6. If the ambient temperature reaches 55C or higher, install an air conditioner to lower the temperature. Resistance to Inrush Current (For repetitive inrush current, keep the inrush current below the values shown by the dotted lines.) G3PW-A245E@/G3PW-A260E@ Inrush current (A. peak) Inrush current (A. peak) G3PW-A220E@ 200 150 400 300 100 200 50 100 0 10 30 50 100 200 500 1,000 5,000 Power ON time (ms) 0 10 30 50 100 200 500 1,000 5,000 Power ON time (ms) 5 G3PW Dimensions Note: All units are in millimeters unless otherwise indicated. 20-A Models with Screwless Clamp Terminal Block G3PW-A220EU-C G3PW-A220EC-C-FLK Mounting Hole Dimensions 137 120 40 50 100 min. 170 1580.2 146.4 380.2 51 min. Two, M5 45/60-A Models with Screwless Clamp Terminal Block Mounting Hole Dimensions G3PW-A245EU-C G3PW-A260EU-C G3PW-A245EC-C-FLK G3PW-A260EC-C-FLK G3PW-A245EU-C G3PW-A245EC-C-FLK 100 min. 155 138 70 104 1760.2 188 171.5 Two, M5 57.60.2 71 min. G3PW-A260EU-C G3PW-A260EC-C-FLK 100 min. 1760.2 Two, M5 6 57.60.2 90 min. G3PW 20-A Models with Terminal Block with Small Slotted Screws G3PW-A220EU-S G3PW-A220EC-S-FLK Mounting Hole Dimensions 136.5 120 40 50 100 min. 170 1580.2 146.4 380.2 51 min. Two, M5 45/60-A Models with Terminal Block with Small Slotted Screws Mounting Hole Dimensions G3PW-A245EU-S G3PW-A260EU-S G3PW-A245EC-S-FLK G3PW-A260EC-S-FLK G3PW-A245EU-S G3PW-A245EC-S-FLK 100 min. 154.5 138 70 104 1760.2 57.60.2 188 Two, M5 171.5 71 min. G3PW-A260-EU-S G3PW-A260-EC-S-FLK 100 min. 1760.2 57.60.2 Two, M5 90 min. Accessories (Order Separately) External Variable Resistor Mounting Holes Nameplate Knob Filled with white resin G32X-V2K 2.51 311 3 dia. 2.80.2 dia. M9P0.75 6 -00.1 dia. 13.4 26 48 120.2 34 120.2 dia. 10.1 R26 max. 1.6 9.5 dia. 15 min. 101 17 max. 201 1.60.2 30 max. 48 6.5 14 17 7 G3PW Safety Precautions WARNING Do not attempt to disassemble the Power Controller while the power is being supplied. Doing so may occasionally result in strong electric shock. Do not touch any of the terminals while the power is being supplied. Also, always attach the terminal block cover after completing wiring. Touching live terminals may occasionally result in serious injury due to electric shock. Fail-safe measures must be taken by the customer to ensure safety in the event of incorrect, missing, or abnormal signals caused by broken signal lines, momentary power interruptions, or other causes. Abnormal operation may result in serious accidents. Do not use the Power Controller where subject to flammable or explosive gas. Otherwise, explosion may occur. Use the wire sizes given in this document and use twisted copper wires or solid copper wire. Use crimp terminals with insulative sleeves. If the crimp terminals do not come with insulative sleeves, attach insulative sleeves. Use the size of crimp terminals specified in this document. Make sure that the phases match for load terminal T1 and power supply terminal 4 (N), and for load terminal L1 and power supply terminal 5 (L). Insert suitable fuses in the power supply line and load output line to protect the circuits. The Power Controller will not operate normally if the wiring is not correct, and the load may be damaged. Leave at least 100 mm of space above and below the Power Controller when installing it to allow heat to dissipate. Do not obstruct the area around the Power Controller and especially the area around the heat sink. Install the Power Controller in the direction shown in this Instruction Sheet. The Power Controller generates a lot of heat and it uses natural heat convection for cooling. Installing the Power Controller in the wrong direction may cause in malfunctions or accidents. Do not touch the terminal sections while a voltage is being applied after the power supply terminal block and load terminal block have been wired. The power supply terminal block and load terminal block are not isolated to enable an alarm function. Electric shock may occur. 8 CAUTION The Power Controller and the heat sink become very hot. Do not touch anything but the setting keys while power is being supplied or just after the power supply is turned OFF. Doing so may cause burns. Do not attempt to disassemble, modify, or repair the Power Controller or touch any of the internal parts. Minor electric shock, fire, or malfunction may occasionally occur. Do not allow chips or filings from installation work, pieces of metal, or wire clippings to enter the Power Controller. Doing so may occasionally result in minor electric shock, fire, or malfunction. Always connect the load to load terminal T1. Also, always connect power supply terminal 4 (N) directly to the power supply. Do not connect it through the load. If the wiring is not correct, the fault detection function of the Power Controller will indicate "E10" and stop the output operation. Check the connection again. When using the Power Controller to control the primary side of a transformer, do not open the circuit on the secondary side of the transformer while the Power Controller is operating. Do not touch the connecting cables while power is being supplied. Static electricity from your body may cause malfunctioning. If a malfunction in the Power Controller prevents control operations or if an alarm cannot be output, it may occasionally cause damage to the connected equipment and devices. To maintain safety in the event of a malfunction in the Power Controller, always take appropriate safety measures, such as installing a separate monitoring system. Set the parameters of the Power Controller so that they are suitable for the system being controlled. If they are not suitable, unexpected operation may occasionally result in property damage or accidents. Tighten the terminal screws to the torque specified in this Instruction Sheet. If the screws are loose, it may occasionally cause a fire. G3PW Precautions for Safe Use OMRON constantly strives to improve quality and reliability. The G3PW, however, uses semiconductors, and semiconductors may commonly malfunction or fail. In particular, it may not be possible to ensure safety if the G3PW is used outside the rated ranges. Therefore, always use the G3PW within the ratings. When using the G3PW, always design the system to ensure safety and prevent human accidents, fires, and social harm in the event of G3PW failure. System design must include measures such as system redundancy, measures to prevent fires from spreading, and designs to prevent malfunction. 1. Do not apply a voltage or current in excess of the ratings to the terminal sections of the G3PW. Doing so may result in failure of the G3PW or fire damage. 2. Do not use the G3PW with loose terminals screws. Abnormal terminal heat may result in fire damage. 3. Do not obstruct the airflow around the heat sink of the G3PW. Abnormal heat may result in failure due to shorting of the output terminals or fire damage. 4. Be sure to read the Precautions for Correct Use to correctly perform wiring and tighten screws. Using the G3PW with incorrect wiring or insufficient screw tightening may result in fire damage due to abnormal heat when the power is supplied. Installation Environment * Use the Power Controller within the rated ambient temperature and humidity ranges. * If multiple Power Controllers are installed side-by-side or vertically, the heat that is generated will cause the internal temperatures of the Power Controllers to rise and will shorten their service life. In these kinds of installations, take suitable measures, such as installing fans for forced cooling. * The Power Controller is designed for indoor use only. Also, do not use the Power Controller in the following environments. * Locations subject to water, oil, or chemicals * Locations subject to direct sunlight * Locations where dust or corrosive gases (in particular, sulfuric or ammonia gas) are present * Locations subject to extreme temperature changes * Locations where icing or condensation may occur * Locations subject to excessive shocks or vibration * Locations subject to direct heat radiated from heating devices Installation and Wiring Safety Measures and Checking * Install a switch or circuit breaker so that the operator can immediately turn OFF the power, and provide a suitable display. * Apply the power supply voltage through the contacts of a switch, relay, or similar device so it reaches the rated voltage within 2 s. If the power supply voltage is increased gradually, the power supply may not be reset or outputs may malfunction. * Use a power supply voltage, input voltage, input current, and load within the specifications and rated ranges for the Power Controller. * Use a load that draws a current at the maximum output that is within the rated current range of the Power Controller. If the current drawn by the load is not within the rated current range, malfunction or fire may occur. * Make sure that the protective cover is attached to the load terminal block before using the Power Controller. Failure to do so may damage internal components due to mechanical stress. Preventing Inductive Noise * Allow as much space as possible between the Power Controller and devices that generate powerful high frequencies (highfrequency welders, high-frequency sewing machines, etc.) or surge. * Keep the signal lines that connect to the Power Controller's terminal block away from power cables carrying high voltages or large currents. Also, do not wire power lines together with or parallel to Power Controller wiring. Using shielded cables and using separate conduits or ducts is recommended. * Attach a surge suppressor or noise filter to peripheral devices that generate noise (in particular, motors, transformers, solenoids, magnetic coils or other equipment that have an inductance component). * When a noise filter is used at the power supply, first check the voltage or current, and attach the noise filter as close as possible to the Power Controller. Cleaning * Do not use paint thinner or similar chemical to clean with. Use commercially available standard grade alcohol. Storage * Store the Power Controller within the rated ambient temperature. * When installing the Power Controller, always securely tighten the top mounting screws first. When removing the Power Controller, always remove the bottom mounting screws first. * Take safety measures, such as wearing safety shoes, in case the Power Controller falls. * Touch the Power Controller only after first touching a grounded metal object to discharge any static electricity from your body. * Always ground the Power Controller to 100 or less. There are no ground terminals provided, so use the heat sink mounting screws as ground terminals. * Check the terminal number and polarity for each input before connecting it. * Use copper twisted wire in the sizes specified in this Instruction Sheet. * Use insulated crimp terminals with insulation sleeves. If using crimp terminals that are not insulated, cover them with insulation sleeves. Also, use terminals of the sizes specified in this Instruction Sheet. * Insert connectors all the way. * Do not connect anything to unused terminals. 9 G3PW Precautions for Correct Use Installation Direction Wiring the Load Terminal Block For cooling efficiency, install the Power Controller in the correct direction. The G3PW generates a lot of heat, and it uses natural heat convection for cooling. Installing the Power Controller in the wrong direction may cause it to malfunction or to be damaged. Recommended Wires When connecting to the load terminals, use the specified wire size for each model of Power Controller. Model Recommended wire size Tightening torque Terminal screws G3PW-A220 AWG 18 to 10 1.8 N*m M4 AWG 6 * 2.8 N*m M5 Top G3PW-A245 G3PW-A260 * Crimp terminals that conform to UL and CSA specifications must be used. Recommended Crimp Terminals * Either use insulated crimp terminals or cover the crimp terminals with insulating sleeves. * Always use the following crimp terminals to wire the load terminals. * Do not connect more than two crimp terminals to one terminal screw. Natural convection Model Bottom A Other device Other device A (mm) G3PW-A220 9.5 max. G3PW-A245/A260 12 max. Recommended Fuses 100 mm min. Airflow Recommended models Super-rapid Fuse (Fuji Electric) Type Fast-acting fuses * Mounting surface For 20 A CR6L-20/UL For 45 A CR6L-50/UL For 60 A CR6L-75/UL Fuse Holder (Fuji Electric) CMS-4 CMS-5 * Ask your OMRON representative for UL certified products. Time-delay fuses specifications Specified distance or longer Type Specification Time-delay fuses 250 VAC, 2 A Command Input and Power Supply Terminal Wiring 100 mm min. Voltage Input (1 to 5 VDC) Other device When using a voltage input, connect the positive and negative signal wires to terminals 1 and 3, respectively. Other device 1 Wiring the Power Supply and Load Circuits The G3PW will not operate correctly if the wiring is not correct. The failure detection function of the G3PW will stop the output from operating. Connect the AC power supply to power supply terminals 4 (N) and 5 (L). Connect the load to load terminal T1 and to the power supply, and then connect the power supply to load terminal L1 through a fastacting fuse. The AC power supply ground polarity and the G3PW terminal block polarity are not related, but connect the 4 (N) and 5 (L) terminals on the command input/power supply terminal block and the T1 and L1 terminals of the load terminal block to power supplies with the same phases. 1 2 T1 Time-delay fuse Power supply 100 to 240 VAC (50/60 Hz) L 5 Load Load circuit (T1) Fast-acting fuse 3 N 4 L 5 Temperature controller or other controller 1 to 5-V output Current Input (4 to 20 mA DC) When using current input, connect the positive and negative signal wires to terminals 2 and 3, respectively. 1 2 3 N 4 L 5 1 2 3 N 4 L 5 1 2 3 N 4 L 5 Temperature controller or other controller 4 to 20 mA output Command input/power supply terminal block L1 Load terminal block Load circuit (L1) 10 N 4 3 2 Max. 6 units are possible to connect (In case, Input impedance of Temperature controller is 600 max.) Note: If you connect more than one G3PW Controller for current input, do not connect the negative terminal of the event input/ reset input (L/N) and the current input terminal -3 as negative commons on the G3PW Controllers. If you do, the second and later G3PW Controllers may not operate. G3PW ON/OFF Voltage Input (0 or 5 VDC) Terminal Names When using an ON/OFF voltage input, connect the positive and negative signal wires to terminals 1 and 3, respectively and apply a command voltage that is 0 or 5V. 1 2 3 N 4 Multi-drop Max. of 31 nodes * 1. RS-485 (+) EJ1 Modular Temperature Controller, CJ-series Serial Communications Unit, etc. L 5 2. RS-485 (-) 3. Main setting 4. Main setting COM 5. Duty setting 6. Duty setting COM PLC or other controller 7. Alarm output 1 (+) Load 8. Alarm output 1 (-) 0 or 5-V output Automatic The G3PW may be damaged if a command voltage that is higher than 5 V is applied. If it is necessary to apply more than 5 V, split the voltage as shown below by inserting resistance in the line to terminal 1 and applying the voltage across terminals 1 and 3. The internal impedance between terminals 1 and 3 is 30.1 k. Internal impedance: 30.1 k 1 2 3 N L Output voltage Output of 5 V or higher Resistance PLC or other controller Resistance 0 or 5 V Not required 0 or 12 V 42 k, 1/5 W min. 0 or 24 V 120 k, 1/5 W min. Command Input and Power Supply Wire Sizes Model Recommended wire diameter Tightening torque Terminal screws All models AWG 18 to 14 0.8 to 1.0 N*m M3.5 10. Alarm output 2 (-) 11. Event input (+) Manual 12. Event input (-) 13. Reset input (+) 14. Reset input (-) For standard models, 1 and 2 are not used. * A terminator must be connected at each end of the RS-485 transmission path. The terminators must be at least 54 combined. Wiring Inputs for External Settings * Wiring to Adjust the Main Setting Use a G32X-V2K Variable Resistor to adjust the main setting. 1 * Wiring to Adjust the Duty Setting Use a G32X-V2K Variable Resistor to adjust the duty setting. 1 3. Main setting Recommended Crimp Terminals Always use the following crimp terminals (for M3.5) to wire to the command input and power supply terminals. 9. Alarm output 2 (+) Load 4. Main setting COM 2 2 5. Duty setting 3 3 6. Duty setting COM 7.2 mm max. Alarm Outputs 7.2 mm max. 1 2 Wiring the Control Terminal Block 3 4 Recommended Wire Sizes and Connection Method G3PW-A2@@E@-S (Models with terminal blocks with small slotted screws) G3PW-A2@@E@-C (Models with screwless clamp terminal block) 5 6 7. Alarm output 1 (+) Load 8. Alarm output 1 (-) 10. Alarm output 2 (-) Model Tightening torque Terminal screws 12 All models AWG 26 to 16 0.22 N*m M2 14 * Use copper AWG 26 to 16 twisted-pair cable when connecting the wires directly. * Strip the wire sheathing for the following lengths, according to the connector type. * Small slotted screw terminals: 7 mm * Screwless clamp terminals: 9 mm * When using twisted wires, it is recommended that you attach a ferrule with an insulating cover that conforms to DIN 46228-4 and connect the ferrule to the terminal. * Use shielded twisted-pair wires for RS-485 communications wires. A maximum of 500 m total of wiring can be used. Failure Detection Wiring Sufficiently consider the safety design of the system design so that the load circuit is turned OFF using the alarm output when a failure is detected in the G3PW. 2 Maximum operating voltage 30 VDC Maximum load current 50 mA Maximum leakage current 11 Recommended wire diameter Open collector Number of outputs Maximum resid1.5 V ual voltage 9. Alarm output 2 (+) Load Wire Sizes for Control Terminals (Models with Small Slotted Screws or Screwless Clamp Terminals) Output status 0.4 mA 13 Wiring an External Noise Filter Always insert a noise filter in the power supply lines to the G3PW. 1 2 T1 Power supply 100 to 240 VAC (50/60 Hz) Noise Filter RSMN-2030/2060 (TDK-Lambda Corporation) 1 3 2 4 Time-delay fuse Load N 4 3 L 5 Command input/power supply terminal block L1 Load terminal block Load circuit (T1) Load circuit (L1) Fast-acting fuse Grounding Always ground the Power Controller to 100 or less. There are no ground terminals provided, so use the heat sink mounting screws as ground terminals. 11 Advanced Digital Temperature Controller E5CN-H (48 x 48 mm) A New High-performance Controller: High Resolution, High Speed, and High Input Accuracy. Logic Operations and Preventive Maintenance Function. * High-resolution display with 5 digits/0.01C display in a compact Controller (48 x 48 mm). * High-speed sampling cycle of 60 ms. * High Accuracy Thermocouple/Pt input: 0.1% of PV Analog input: 0.1% FS * Universal inputs on all models (thermocouple, PT, or analog input) to handle various sensors with one Controller. * A PV/SV-status display function can be set to automatically alternate between displaying the status of the Temperature Controller (auto/ manual, RUN/STOP, and alarms) and the PV or SV. * Flexible contact outputs with logic operations (AND, OR, and delays) set from the Support Software (CX-Thermo Ver. 4.0) * Preventive maintenance for relays in the Temperature Controller using a Control Output ON/OFF Counter. 48 x 48 mm E5CN-H Advanced Digital Temperature Controller E5AN-H/E5EN-H (96 x 96 mm and 48 x 96 mm) A New High-performance Controller: High Resolution, High Speed, and High Input Accuracy. Logic Operations and Preventive Maintenance Function. Plus Infrared Port on Front Panel. * High-resolution display with 5 digits/0.01C display. * High-speed sampling cycle of 60 ms. * High Accuracy Thermocouple/Pt input: 0.1% of PV Analog input: 0.1% FS * Universal inputs on all models (thermocouple, PT, or analog input) to handle various sensors with one Controller. Models also available with Remote SP. * A PV/SV-status display function can be set to automatically alternate between displaying the status of the Temperature Controller (auto/manual, RUN/STOP, and alarms) and the PV or SV. * Flexible contact outputs with logic operations (AND, OR, and delays) set from the Support Software (CX-Thermo Ver. 4.0) * Preventive maintenance for relays in the Temperature Controller using a Control Output ON/OFF Counter. * Model available with position-proportional control 12 96 x 96 mm E5AN-H 48 x 96 mm E5EN-H Solid State Relays for Heaters Single-phase G3PE Compact, Slim-profile SSRs with Heat Sinks. Models with No Zero Cross for a Wide Range of Applications. * RoHS compliant. * Models also available with no zero cross * Surge pass protection improved surge dielectric strength for output currents. (OMRON testing) * Compact with a slim profile. * Mount to DIN Track or with screws. * Conforms to UL, CSA, and EN standards (TUV certification). Solid State Contactors for Heaters Three-phase G3PE Compact, Slim-profile SSRs with Heat Sinks. Solid State Contactors for Three-phase Heaters Reduced Installation Work with DIN Track Mounting. * RoHS compliant. * Surge pass protection improved surge dielectric strength for output currents. (OMRON testing) * Slim design with 3-phase output and built-in heat sinks. * DIN Track mounting types and screw mounting types are available. All DIN Track mounting types mount to DIN Track (applicable DIN Track: TR35-15Fe (IEC 60715)). * Conforms to UL, CSA, and EN standards (TUV certification). 13 MEMO 14 Warranty and Application Considerations Read and Understand This Catalog Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. Warranty and Limitations of Liability WARRANTY OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified) from date of sale by OMRON. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. LIMITATIONS OF LIABILITY OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS, OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY. In no event shall the responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted. IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR. Application Considerations SUITABILITY FOR USE OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of products in the customer's application or use of the products. Take all necessary steps to determine the suitability of the product for the systems, machines, and equipment with which it will be used. Know and observe all prohibitions of use applicable to this product. NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCTS ARE PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. Disclaimers PERFORMANCE DATA Performance data given in this catalog is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of OMRON's test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to the OMRON Warranty and Limitations of Liability. CHANGE IN SPECIFICATIONS Product specifications and accessories may be changed at any time based on improvements and other reasons. Consult with your OMRON representative at any time to confirm actual specifications of purchased product. DIMENSIONS AND WEIGHTS Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown. OMRON Corporation Industrial Automation Company Authorized Distributor: Tokyo, JAPAN Contact: www.ia.omron.com Regional Headquarters OMRON EUROPE B.V. Wegalaan 67-69-2132 JD Hoofddorp The Netherlands Tel: (31)2356-81-300/Fax: (31)2356-81-388 OMRON ELECTRONICS LLC One Commerce Drive Schaumburg, IL 60173-5302 U.S.A. Tel: (1) 847-843-7900/Fax: (1) 847-843-7787 OMRON ASIA PACIFIC PTE. LTD. No. 438A Alexandra Road # 05-05/08 (Lobby 2), Alexandra Technopark, Singapore 119967 Tel: (65) 6835-3011/Fax: (65) 6835-2711 OMRON (CHINA) CO., LTD. Room 2211, Bank of China Tower, 200 Yin Cheng Zhong Road, PuDong New Area, Shanghai, 200120, China Tel: (86) 21-5037-2222/Fax: (86) 21-5037-2200 (c) OMRON Corporation 2008 All Rights Reserved. In the interest of product improvement, specifications are subject to change without notice. CSM_11_1_0514 Printed in Japan Cat. No. J176-E1-01 1008 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Omron: G3PW-A220EC-S-FLK G3PW-A260EU-S G3PW-A245EU-S G3PW-A245EC-S-FLK G3PW-A260EC-C-FLK G3PWA245EC-C-FLK G3PW-A260EU-C G3PW-A220EU-S G3PW-A260EC-S-FLK G3PW-A220EC-C-FLK G3PWA245EU-C G3PW-A220EU-C