TM Scotch-Weld Epoxy Adhesives DP190 Translucent and Gray Technical Data Product Description March 2019 3MTM Scotch-WeldTM Epoxy Adhesive DP190 Translucent is a 1:1 mix ratio similar to 3MTM Scotch-WeldTM Epoxy Adhesive 2216 B/A Translucent but faster curing. 3MTM Scotch-WeldTM Epoxy Adhesive DP190 Gray is a 1:1 by volume mix ratio of 3MTM Scotch-WeldTM Epoxy Adhesive 2216 B/A Gray and exhibits good peel, shear and environmental aging properties. Available in bulk containers as 3MTM Scotch-WeldTM Epoxy Adhesive 2216 B/A. Features * 90 minute worklife * High shear and peel strength * Flexible * 1:1 mix ratio * Translucent or gray color Typical Uncured Physical Properties Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes. Base Resins Viscosity1, Approximate Base (B) @ 75F Accelerator (A) 3MTM ScotchWeldTM Epoxy Adhesive DP190 Translucent 3MTM ScotchWeldTM Epoxy Adhesive DP190 Gray Epoxy/Amine Epoxy/Amine 2,000-8,000 cps 7,000-15,000 cps 75,000-150,000 cps 40,000-80,000 cps Net Weight (Lbs./gal.) Base (B) Accelerator (A) 9.3-9.7 8.2-8.6 11.0-11.4 10.6-11.0 Color (Lbs./gal.) Base (B) Accelerator (A) Clear Amber White Gray Mix Ratio (B:A) By Volume By Weight 1:1 1.15:1 1:1 1.06:1 Worklife2 @ 73F (23C) 2 gram 20 gram 80 min. 60 min. -- 90 min. Footnotes: 1. Viscosity determined using 3M test method C-1D. Procedure involves Brookfield RVF, #7 spindle, 20 rpm and 80F (26C). Measurement taken after 1 minute rotation. 2. Worklife determined using 3M test method C-3180. Procedure involves periodically measuring a 2 gram mixed mass for selfleveling and wetting properties. This time will also approximate the usable worklife in an 3MTM EPXTM Applicator mixing nozzle. 3MTM Scotch-WeldTM Epoxy Adhesives DP190 Translucent and Gray Typical Cured Properties Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes. Physical Footnotes: 3. Tack-free time determined per 3M test method C-3173. Involves dispensing 0.5 gram amount of adhesive onto substrate and testing periodically for no adhesive transfer to metal spatula. 4. Handling strength determined per 3M test method C-3179. Time to handling strength taken to be that required to achieve a 50 psi OLS strength using aluminum substrates. 5. The cure time is defined as that time required for the adhesive to achieve a minimum of 80% of the ultimate strength as measured by aluminum-aluminum OLS. 6. Tensile and Elongation. Used procedure in 3M test method C-3094/ATSM D 882. Samples were 2 in. dumbbells with .0125 in. neck and .030 in. sample thickness. Separation rate was 2 inches per minute. Samples cured 2 hrs RT plus 2 hrs/ 160F (71C). 7. Weight loss by TGA reported as that temperature at which 5% weight loss occurs by TGA in air at 5C rise per minute per ASTM 1131-86. 8. TCE determined using TMA Analyzer using a heating rate of 50F (10C) per minute. Second heat values given. 9. Glass Transition Temperature (Tg) determined using DSC Analyzer with a heating rate of 68F (20C) per minute. Second heat values given. 10. Thermal conductivity determined using ASTM C177 and C-matic Instrument using 2 in. diameter samples. 11. Thermal shock resistance run per 3M test method C-3174. Involves potting a metal washer into a 2 in. x 0.5 in. thick section and cycling this test specimen to colder and colder temperatures. Color Hardness (ASTM D 2240) Shore D Worklife2 Tack-free Time3 Time to Handling Strength4 Full Cure Time5 Elongation6 Tensile Strength6 3MTM Scotch-WeldTM Epoxy Adhesive DP190 Translucent Translucent 3MTM Scotch-WeldTM Epoxy Adhesive DP190 Gray Gray 35 80 minutes ~ 4 hrs 6 hrs 14 days 120% 2750 psi 60 90 minutes ~ 6 hrs 8-12 hrs 7 days 30% 3500 psi 3MTM ScotchWeldTM Epoxy Adhesive DP190 Translucent 1% @ 390F (199C) 5% @ 594F (312C) 3MTM ScotchWeldTM Epoxy Adhesive DP190 1% @ 477FGray (247C) 5% @ 639F (337C) 86 (41-68F [5-20C] range) 166 (167-284F [75-140C] range) 62 (41-68F [5-25C] range) 177 (167-284F [65-140C] range) 50F (10C) 80F (27C) 45F (7C) 68F (20C) .079 .39 x 10-3 .136 .220 90.9 x 10-2 .381 Pass 5 cycles without cracking Pass 5 cycles without cracking 3MTM ScotchWeldTM Epoxy Adhesive DP190 Translucent 6.2 3MTM ScotchWeldTM Epoxy Adhesive DP190 6.5Gray 0.16 0.09 875 volts/mil 830 volts/mil 7.5 x 1010 ohm-cm 5.0 x 1012 ohm-cm Thermal Weight Loss by Thermal Gravimetric Analysis (TGA)7 Thermal Coefficient of Expansion (TCE) by TMA8 ( x 10 -6 units/unit/C) Below Tg Above Tg Glass Transition Temperature (Tg) by DCS 9 Onset Mid-Point Thermal Conductivity10 (@ 110F on .250 in. samples) BTU - ft./ft.2 - hr. - F) Cal./sec. - cm - C) Watt/m - C Thermal Shock Resistance11 Potted Washer Olyphant Test (3M ITSD Test Method C-3174 +100C [air] to -50C [liquid]) Electrical Dielectric Constant @ 1 KHZ @ 73F (23C) (ASTM D 150) Dissipation Factor @ 1 KHZ @ 73F (23C) (ASTM D 150) Dielectric Strength (ASTM D 149) Sample Thickness Approx. 30 mil. Volume Resistivity (ASTM D 257) -2- 3MTM Scotch-WeldTM Epoxy Adhesives DP190 Translucent and Gray Typical Adhesive Performance Characteristics The following product performance data were obtained in the 3M laboratory under the conditions specified. The following data show typical results obtained with the 3MTM Scotch-WeldTM Adhesives when applied to properly prepared substrates, cured, and tested according to the specifications indicated. The data were generated using the 3MTM EPXTM Applicator System equipped with an EPX applicator static mixer, according to manufacturer's directions. Thorough hand mixing should afford comparable results. Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes. Overlap Shear Strength (OLS) to12 (Bonds cured 24 hrs @ RT + 2 hrs 160F [71C]) Etched Aluminum 3MTM Scotch-WeldTM Epoxy Adhesive DP190 Translucent 3MTM Scotch-WeldTM Epoxy Adhesive DP190 Gray 1800 psi 2500 psi Sanded Aluminum (60 grit) 850 psi 1500 psi Cold Rolled Steel 850 psi 1400 psi Wood, Fir 650 psi 1100 psi Glass, Borosilicate 260 psi 300 psi Glass, +3MTM Scotch-WeldTM Primer 3901 300 psi 300 psi Polycarbonate 400 psi 800 psi Acrylic 350 psi 500 psi Fiberglass 1000 psi 1600 psi ABS 400 psi 700 psi PVC 650 psi 800 psi 90 psi 50 psi Polypropylene Rate of Strength Buildup (OLS on Etched Aluminum)12 Bonds tested after: 1 hr @ RT 3MTM ScotchWeldTM Epoxy Adhesive DP190 Translucent 10 psi 3MTM ScotchWeldTM Epoxy Adhesive DP190 10 Gray psi 6 hrs @ RT 200 psi 50 psi 24 hrs @ RT 800 psi 1000 psi 7 days @ RT 1200 psi 2000 psi 1 mo @ RT 1800 psi 2200 psi 3 mos @ RT 1800 psi 2500 psi Footnotes: 12. Overlap shear (OLS) strengths were measured on 1 in. wide 1/2 in. overlap specimens. These bonds were made individually using 1 in. x 4 in. pieces of substrate. The thickness of the bond line was 0.005-0.008 in. All strengths were measured at 70F (21C) except were noted. (Test per ASTM D 1002-72.) The separation rate of the testing jaws was 0.1 in. per minute for metals, 2 in. per minute for plastics and 20 in. per minute for rubbers. The thickness of the substrates were: steel, 0.060 in.; other metals, 0.05-0.064 in.; rubber, 0.125 in.; plastics, 0.125 in. -3- 3MTM Scotch-WeldTM Epoxy Adhesives DP190 Translucent and Gray Typical Adhesive Performance Characteristics (continued) Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes. Environmental Aging (OLS on Etched Aluminum)12 Bonds tested after: 3MTM Scotch-WeldTM Epoxy Adhesive DP190 Translucent 3MTM Scotch-WeldTM Epoxy Adhesive DP190 Gray 24 hrs RT + 2 hrs @ 160F (71C) 1700 psi 2500 psi 24 hrs RT + 2 hrs @ 240F (115C) 3200 psi 3000 psi 1 wk RT + wk @ 90F/90% RH 1400 psi 2400 psi 1 wk RT + 1 wk 248F (120C) 3500 psi 3500 psi 1 wk RT + 1 wk H2O Immersion 1700 psi 2500 psi Footnotes: 12. Overlap shear (OLS) strengths were measured on 1 in. wide 1/2 in. overlap specimens. These bonds were made individually using 1 in. x 4 in. pieces of substrate. The thickness of the bond line was 0.005-0.008 in. All strengths were measured at 70F (21C) except were noted. (Test per ASTM D 1002-72.) The separation rate of the testing jaws was 0.1 in. per minute for metals, 2 in. per minute for plastics and 20 in. per minute for rubbers. The thickness of the substrates were: steel, 0.060 in.; other metals, 0.05-0.064 in.; rubber, Overlap Shear Strength vs Temperature12 (Bonds cured 24 hr @ RT + 2 hrs @ 160F [71C]) Bonds tested at: 0.125 in.; plastics, 0.125 in. 13. Solvent resistance was determined using cured (24 hrs RT + 2 hrs 160F [71C] samples (1/2 in. x 4 in. x 1/8 in. thickness) immersed in the test solvent for 1 hour and 1 month. After the allotted period of time the sample was removed and visually examined for surface attack as compared to the control. -67F (-55C) 3MTM Scotch-WeldTM Epoxy Adhesive DP190 Translucent 3500 psi 3MTM Scotch-WeldTM Epoxy Adhesive DP190 Gray 1500 psi 70F (21C) 1200 psi 2500 psi 120F (49C) 290 psi 1000 psi 150F (66C) 200 psi 600 psi 180F (82C) 160 psi 400 psi 180F Peel Strength vs Temperature12 (Bonds cured 24 hr @ RT + 4 hrs @ 160F [71C]) Bonds tested at: -67F (-55C) 3MTM Scotch-WeldTM Epoxy Adhesive DP190 Translucent 3 piw 70F (21C 3MTM Scotch-WeldTM Epoxy Adhesive DP190 Gray 3 piw 20 piw 20 piw 120F (49C) 3 piw 10 piw 150F (66C) 2 piw 4 piw 180F (82C) 1 piw 2 piw Solvent Resistance13 Acetone One Hour/One Month 3MTM Scotch-WeldTM Epoxy Adhesive DP190 Translucent A/A One Hour/One Month 3MTM Scotch-WeldTM Epoxy Adhesive DP190 Gray A/A Isopropyl Alcohol A/A A/A Freon TF A/A A/A Freon TMC A/B A/A 1,1,1-Trichlorethane A/A A/A RMA Flux A/A A/A Key: A - Unaffected, B - Slight Attack, C - Moderate/Severe Attack -4- 3MTM Scotch-WeldTM Epoxy Adhesives DP190 Translucent and Gray 3MTM EPXTM Pneumatic Applicator Delivery Rates 200 ml Applicator - Maximum Pressure 58 psi Adhesive* 6mm Nozzle gms/minute 10mm Nozzle gms/minute 11.9 46.0 3MTM Scotch-WeldTM Epoxy Adhesive DP190 Gray 48.5/50 ml Applicator - Maximum Pressure 50 psi 1/4 in. Nozzle gms/minute Adhesive* 3MTM Scotch-WeldTM Epoxy Adhesive DP190 Translucent Scotch-Weld epoxy adhesive DP190 Gray Scotch-Weld epoxy adhesive DP190 Gray Scotch-Weld epoxy adhesive DP190 100F (38C) 112 16.9 21.5 (nozzle cut back 2 divisions) 41.1 *Tests were run at a temperature of 70F 2F (21C 1C) and at maximum applicator pressure. Handling/Curing Information Directions For Use 1. For high strength structural bonds, paints, oxide films, oils, dust, mold release agents and all other surface contaminants must be completely removed. However, the amount of surface preparation necessary directly depends on the required bond strength and the environmental aging resistance desired by the user. For suggested surface preparations on common substrates, see the section on surface preparation. 2. Mixing For Duo Pak Cartridges 3MTM Scotch-WeldTM Epoxy Adhesives DP190 Translucent and DP190 Gray are supplied in a dual syringe plastic duo-pak cartridge as part of the 3MTM EPX Applicator system. To use, simply insert the duo-pak cartridge into the EPX applicator and start the plunger into the cylinders using light pressure on the trigger. Next, remove the duo-pak cartridge cap and expel a small amount of adhesive to be sure both sides of the duo-pak cartridge are flowing evenly and freely. If automatic mixing of Part A and Part B is desired, attach the EPX applicator mixing nozzle to the duo-pak cartridge and begin dispensing the adhesive. For hand mixing, expel the desired amount of adhesive and mix thoroughly. Mix approximately 15 seconds after uniform color is obtained. For Bulk Containers Mix thoroughly by weight or volume in the proportions specified in the typical uncured properties section. Mix approximately 15 seconds after uniform color is obtained. 3. For maximum bond strength, apply adhesive evenly to both surfaces to be joined. 4. Application to the substrates should be made within 75 minutes. Larger quantities and/or higher temperatures will reduce this working time. 5. Join the adhesive coated surfaces and allow to cure at 60F (16C) or above until completely firm. Heat up to 200F (93C) will speed curing. These products will cure in 7 to 14 days @ 75F (24C). 6. Keep parts from moving during cure. Contact pressure necessary. Maximum shear strength is obtained with a 3-5 mil bond line. 7. Excess uncured adhesive can be cleaned up with ketone type solvents.* *Note: When using solvents, extinguish all ignition sources, including pilot lights, and follow manufacturer's precautions and directions for use. Adhesive Coverage (typical): A 0.005 in. thick bondline will yield a coverage of -5- 3MTM Scotch-WeldTM Epoxy Adhesives DP190 Translucent and Gray Surface Preparation For high strength structural bonds, paint, oxide films, oils, dust, mold release agents and all other surface contaminants must be completely removed. However, the amount of surface preparation necessary directly depends on the required bond strength and the environmental aging resistance desired by the user. The following cleaning methods are suggested for common surfaces: Steel: 1. Wipe free of dust with oil-free solvent such as acetone, isopropyl or alcohol solvents.* 2. Sandblast or abrade using clean fine grit abrasives. 3. Wipe again with solvent to remove loose particles. 4. If a primer is used, it should be applied within 4 hours after surface preparation. Aluminum: 1. Alkaline Degrease: Oakite 164 solution (9-11 oz./gallon water) at 190F (87C) 10F for 10-20 minutes. Rinse immediately in large quantities of cold running water.* 2. Acid Etch: Place panels in the following solution for 10 minutes at 150F (65C) 5F.* Sodium Dichromate 4.1 - 4.9 oz./gallon Sulfuric Acid, 66Be 38.5 - 41.5 oz./gallon 2024-T3 aluminum (dissolved) 0.2 oz./gallon minimum Tap water as needed to balance 3. Rinse: Rinse panels in clear running tap water. 4. Dry: Air dry 15 minutes; force dry 10 minutes at 150F (65C) 10F. 5. If primer is to be used, it should be applied within 4 hours after surface preparation. Plastics/Rubber: 1. Wipe with isopropyl alcohol.* 2. Abrade using fine grit abrasives. 3. Wipe with isopropyl alcohol.* Glass: 1. Solvent wipe surface using acetone or MEK.* 2. Apply a thin coating (0.0001 in. or less) of 3MTM Scotch-WeldTM Metal Primer EC3901 or equivalent to the glass surfaces to be bonded and allow the primer to dry before bonding. *Note: When using solvents, extinguish all ignition sources, including pilot lights, and follow manufacturer's precautions and directions for use. Application Equipment Suggestions For smaller or intermittent applications, the 3MTM EPX Applicator is a convenient method of application. For larger applications these products may be applied by use of flow equipment. Two-part meter/mixing/proportioning/dispensing equipment is available for intermittent or production line use. These systems may be desirable because of their variable shot size and flow rate characteristics and are adaptable to many applications. -6- 3MTM Scotch-WeldTM Epoxy Adhesives DP190 Translucent and Gray Storage Store products at 60-80F (15-27C) for maximum shelf life. Shelf Life These products have a shelf life of 24 months in their unopened original containers from date of manufacture. Precautionary Information Refer to Product Label and Material Safety Data Sheet for health and safety information before using this product. For additional health and safety information, call 1-800-364-3577 or (651) 737-6501. Technical Information The technical information, guidance, and other statements contained in this document or otherwise provided by 3M are based upon records, tests, or experience that 3M believes to be reliable, but the accuracy, completeness, and representative nature of such information is not guaranteed. Such information is intended for people with knowledge and technical skills sufficient to assess and apply their own informed judgment to the information. No license under any 3M or third party intellectual property rights is granted or implied with this information. Product Selection and Use Many factors beyond 3M's control and uniquely within user's knowledge and control can affect the use and performance of a 3M product in a particular application. As a result, customer is solely responsible for evaluating the product and determining whether it is appropriate and suitable for customer's application, including conducting a workplace hazard assessment and reviewing all applicable regulations and standards (e.g., OSHA, ANSI, etc.). Failure to properly evaluate, select, and use a 3M product and appropriate safety products, or to meet all applicable safety regulations, may result in injury, sickness, death, and/or harm to property. Warranty, Limited Remedy, and Disclaimer Unless a different warranty is specifically stated on the applicable 3M product packaging or product literature (in which case such warranty governs), 3M warrants that each 3M product meets the applicable 3M product specification at the time 3M ships the product. 3M MAKES NO OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR ARISING OUT OF A COURSE OF DEALING, CUSTOM, OR USAGE OF TRADE. If a 3M product does not conform to this warranty, then the sole and exclusive remedy is, at 3M's option, replacement of the 3M product or refund of the purchase price Limitation of Liability Except for the limited remedy stated above, and except to the extent prohibited by law, 3M will not be liable for any loss or damage arising from or related to the 3M product, whether direct, indirect, special, incidental, or consequential (including, but not limited to, lost profits or business opportunity), regardless of the legal or equitable theory asserted, including, but not limited to, warranty, contract, negligence, or strict liability. ISO 9001: 2000 This Industrial Adhesives and Tapes Division product was manufactured under a 3M quality system registered to ISO 9001: 2000 standards. Industrial Adhesives and Tapes Division 3M Center, Building 225-3S-06 St. Paul, MN 55144-1000 800-362-3550 * 877-369-2923 (Fax) www.3M.com/structuraladhesives 3M, Scotch-Weld and EPX are trademarks of 3M Company. Printed in U.S.A. (c)3M 2010 78-6900-2952-1 (4/10) -7-