MIC811/812 Microprocessor Reset Circuits General Description Features The MIC811 and MIC812 are inexpensive microprocessor supervisory circuits that monitor power supplies in microprocessor based systems. * Precision voltage monitor for 3V, 3.3V or 5V power supplies * /RESET remains valid with VCC as low as 1V * 5A typical supply current * 140ms minimum reset pulse width available * Manual reset input * Available in 4-pin SOT-143 package The function of this device is to assert a reset if either the power supply drops below a designated reset threshold level or /MR is forced low. Several different reset threshold levels are available to accommodate 3V, 3.3V or 5V powered systems. The MIC811 has an active low /RESET output, while the MIC812 offers an active high RESET output. The reset output is guaranteed to remain asserted for a minimum of 140ms after VCC has risen above the designed reset threshold level. Having a push-pull output stage, the MIC811/812 does not require a pull-up resistor at the output. The MIC811/812 comes in a 4-pin SOT-143 package. Applications * * * * * Portable equipment Intelligent instruments Critical microprocessor power monitoring Printers/computers Controllers If a microprocessor voltage supervisor with an open-drain output stage is needed, see MIC6315. Datasheets and support documentation are available on Micrel's web site at: www.micrel.com. Typical Application Micrel Inc. * 2180 Fortune Drive * San Jose, CA 95131 * USA * tel +1 (408) 944-0800 * fax + 1 (408) 474-1000 * http://www.micrel.com September 9, 2014 Revision 2.0 Micrel, Inc. MIC811/812 Ordering Information Part Number Pb-Free Marking(1) Threshold Voltage Operating Temp. Range Package MIC811LUY KL 4.63 -40C to +85C 4-pin SOT-143 MIC811MUY KM 4.38 -40C to +85C 4-pin SOT-143 MIC811JUY KJ 4.00 -40C to +85C 4-pin SOT-143 MIC811TUY KT 3.08 -40C to +85C 4-pin SOT-143 MIC811SUY KS 2.93 -40C to +85C 4-pin SOT-143 MIC811RUY KR 2.63 -40C to +85C 4-pin SOT-143 MIC812LUY LL 4.63 -40C to +85C 4-pin SOT-143 MIC812MUY LM 4.38 -40C to +85C 4-pin SOT-143 MIC812JUY LJ 4.00 -40C to +85C 4-pin SOT-143 MIC812TUY LT 3.08 -40C to +85C 4-pin SOT-143 MIC812SUY LS 2.93 -40C to +85C 4-pin SOT-143 MIC812RUY LR 2.63 -40C to +85C 4-pin SOT-143 Note: 1. "_" underbar symbol not to scale Pin Configuration MIC811 4-Pin SOT-143 (U) MIC812 4-Pin SOT-143 (U) Pin Description MIC811 MIC812 Pin Name Pin Name 1 1 GND 2 N/A /RESET /RESET goes low if VCC falls below the reset threshold and remains asserted for one reset timeout period (140ms min.) after VCC exceeds the reset threshold. N/A 2 RESET RESET goes high if VCC falls below the reset threshold and remains asserted for one reset timeout period (140ms min.) after VCC exceeds the reset threshold. IC Ground Pin. 3 3 /MR Manual Reset Input. A logic low on /MR will force a reset. The reset will remain asserted as long as /MR is held low and for one reset timeout period (140ms min.) after /MR goes high. This input can be shorted to ground via a switch or driven from CMOS or TTL logic. Float if unused. 4 4 VCC Power Supply Input. September 9, 2014 2 Revision 2.0 Micrel, Inc. MIC811/812 Absolute Maximum Ratings(2) Operating Ratings(3) Terminal Voltage (VCC) ................................ -0.3V to +6.0V Input Current (VCC, /MR)............................................ 20mA Output Current (/RESET, RESET) .............................. 20mA Lead Temperature (soldering, 10s) ............................ 300C Storage Temperature (Ts)............................... 5C to 150C Rate of Rise (VCC) ................................................. 100V/s ESD Rating(4) .................................................................. 3kV Operating Temperature Range MIC811 ................................................. -40C to +85C MIC812 ................................................. -40C to +85C Power Dissipation (TA = +70C) ............................... 320mW Thermal Resistance SOT-143 (JA) .................................................. 265C/W Electrical Characteristics(5) For typical values, VCC = 5V for MIC8_L/M/J, VCC = 3.3V for MIC8_S/T, VCC = 3V for MIC8_R; TA = 25C, bold values indicate - 40C to TA +85C; unless noted. Symbol Parameter Condition VCC Operating Voltage Range TA = -40C to 85C IVCC VTH Supply Current Reset Voltage Threshold tRST Reset Timeout Period VOH /RESET Output Voltage VOL /RESET Output Voltage VOH RESET Output Voltage VOL RESET Output Voltage Min Typ 1 Max Units 5.5 V MIC811L/M/J, MIC812L/M/J: VCC = 5.0V, no load 5 15 A MIC811S/T, MIC812S/T: VCC = 3.3V, no load 5 10 A MIC811R, MIC812R: VCC = 3.0V, no load 5 10 A MIC811L, MIC812L 4.50 4.63 4.75 V MIC811M, MIC812M 4.25 4.38 4.50 V MIC811J, MIC812J 3.89 4.00 4.10 V MIC811T, MIC812T 3.00 3.08 3.15 V MIC811S, MIC812S 2.85 2.93 3.00 V MIC811R, MIC812R 2.55 2.63 2.70 V 140 240 560 ms ISOURCE = 800A, MIC811L/M/J VCC-1.5V V ISOURCE = 500A, MIC811R/S/T 0.8xVCC V VCC = VTH min., ISINK = 3.2mA, MIC811L/M/J 0.4 V VCC = VTH min., ISINK = 1.2mA, MIC811R/S/T 0.3 V VCC >1V, ISINK = 50A, TA = -40C to +85C 0.3 V 1.8V <VCC <VTH min., ISOURCE = 150A 0.8xVCC V ISINK = 3.2mA, MIC812L/M/J 0.4 V ISINK = 1.2mA, MIC812R/S/T 0.3 V Notes: 2. Exceeding the absolute maximum ratings may damage the device. 3. The device is not guaranteed to function outside its operating ratings. 4. Devices are ESD sensitive. Handling precautions are recommended. Human body model, 1.5k in series with 100pF. 5. Specification for packaged product only September 9, 2014 3 Revision 2.0 Micrel, Inc. MIC811/812 Electrical Characteristics (Continued)(5) For typical values, VCC = 5V for MIC8_L/M/J, VCC = 3.3V for MIC8_S/T, VCC = 3V for MIC8_R; TA = 25C, bold values indicate -40C to TA +85C; unless noted. Symbol Parameter Condition Min VCC > VTH max., MIC81_L/M/J MIC81_R/S/T VIL /MR Input Threshold Units s s 0.5 /MR to Reset Delay /MR Input Threshold Max 10 /MR Minimum Pulse Width VIH Typ 2.3 V 0.7xVCC V VCC > VTH max., MIC81-L/M/J MIC81_R/S/T 10 /MR Pull-Up Resistance /MR Glitch Immunity 20 100 0.8 V 0.25xVCC V 30 k ns Timing Diagram Reset Timing Diagram Functional Diagram September 9, 2014 4 Revision 2.0 Micrel, Inc. MIC811/812 /RESET Valid at Low Voltage A resistor can be added from the /RESET pin to ground to ensure the /RESET output remains low with VCC down to 0V. A 100k resistor connected from the /RESET to ground is recommended. The size of the resistor should be large enough not to load the output excessively and small enough to pull-down any stray leakage currents. Application Information Microprocessor Reset The /RESET (or RESET) pin is asserted whenever VCC falls below the reset threshold voltage. The /RESET pin remains asserted for a period of 140ms after VCC has risen above the reset threshold voltage. The reset function ensures that the microprocessor is properly reset and powers up in a known condition after a power failure. /RESET will remain valid with VCC as low as 1V. VCC Transients The MIC811/812 are relatively immune to negative-going VCC glitches below the reset threshold. Typically, a negative-going transient 125mV below the reset threshold with a duration of 20s or less will not cause a reset. Interfacing to Bidirectional Reset Pins The MIC811/812 can interface with Ps with bidirectional reset pins by connecting a 4.7k resistor in series with the MIC811/812 output and the P reset pin. September 9, 2014 Reset Valid to VCC = 0V 5 Revision 2.0 Micrel, Inc. MIC811/812 Package Information 4-Pin SOT-143 (U) September 9, 2014 6 Revision 2.0 Micrel, Inc. MIC811/812 MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com Micrel, Inc. is a leading global manufacturer of IC solutions for the worldwide high performance linear and power, LAN, and timing & communications markets. The Company's products include advanced mixed-signal, analog & power semiconductors; highperformance communication, clock management, MEMs-based clock oscillators & crystal-less clock generators, Ethernet switches, and physical layer transceiver ICs. Company customers include leading manufacturers of enterprise, consumer, industrial, mobile, telecommunications, automotive, and computer products. Corporation headquarters and state-of-the-art wafer fabrication facilities are located in San Jose, CA, with regional sales and support offices and advanced technology design centers situated throughout the Americas, Europe, and Asia. Additionally, the Company maintains an extensive network of distributors and reps worldwide. Micrel makes no representations or warranties with respect to the accuracy or completeness of the information furnished in this datasheet. This information is not intended as a warranty and Micrel does not assume responsibility for its use. Micrel reserves the right to change circuitry, specifications and descriptions at any time without notice. No license, whether express, implied, arising by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Micrel's terms and conditions of sale for such products, Micrel assumes no liability whatsoever, and Micrel disclaims any express or implied warranty relating to the sale and/or use of Micrel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser's use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser's own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale." (c) 2014 Micrel, Incorporated. September 9, 2014 7 Revision 2.0 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Micrel: MIC811JUY TR MIC811LUY TR MIC811RUY TR MIC811SUY TR MIC812JUY TR MIC812LUY TR MIC812MUY TR MIC812RUY TR MIC812SUY TR MIC812TUY TR MIC811SUY-TR MIC812TUY-TR MIC811LUY-TR MIC812SUY-TR MIC811JUY-TR MIC812RUY-TR MIC812MUY-TR MIC812LUY-TR MIC811RUY-TR MIC812JUYTR