WP934RS/SRD T-1 (3mm) Single-Level Circuit Board Indicator DESCRIPTIONS z z z z PACKAGE DIMENSIONS The Super Bright Red source color devices are made with Gallium Aluminum Arsenide Red Light Emitting Diode Electrostatic discharge and power surge could damage the LEDs It is recommended to use a wrist band or anti-electrostatic glove when handling the LEDs All devices, equipments and machineries must be electrically grounded FEATURES z z z z z z z Pre-trimmed leads for pc mounting Pillars are designed for positioning the housing on P.C. board Black case enhances contrast ratio High reliability life measured in years Housing UL rating: 94V-0 Housing material: Type 66 nylon RoHS compliant APPLICATIONS z z z z z Status indicator Illuminator Signage applications Decorative and entertainment lighting Commercial and residential architectural lighting Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is 0.25(0.01") unless otherwise noted. 3. Lead spacing is measured where the leads emerge from the package. 4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. ATTENTION Observe precautions for handling electrostatic discharge sensitive devices SELECTION GUIDE Part Number WP934RS/SRD Emitting Color (Material) Super Bright Red (GaAlAs) Iv (mcd) @ 20mA [2] Viewing Angle [1] Lens Type Min. Typ. 150 400 Red Diffused 21/2 50 *50 *100 Notes: 1. 1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity / luminous flux: +/-15%. * Luminous intensity value is traceable to CIE127-2007 standards. (c) 2018 Kingbright. All Rights Reserved. Spec No: DSAF1861 / 1102013074 Rev No: V.10A Date: 12/14/2018 Page 1 / 4 WP934RS/SRD ELECTRICAL / OPTICAL CHARACTERISTICS at TA=25C Parameter Symbol Emitting Color peak Value Unit Typ. Max. Super Bright Red 655 - nm dom [1] Super Bright Red 640 - nm Spectral Bandwidth at 50% REL MAX IF = 20mA Super Bright Red 20 - nm Capacitance C Super Bright Red 45 - pF Forward Voltage IF = 20mA VF [2] Super Bright Red 1.85 2.5 V Reverse Current (VR = 5V) IR Super Bright Red - 10 A Wavelength at Peak Emission IF = 20mA Dominant Wavelength IF = 20mA Notes: 1. The dominant wavelength (d) above is the setup value of the sorting machine. (Tolerance d : 1nm. ) 2. Forward voltage: 0.1V. 3. Wavelength value is traceable to CIE127-2007 standards. 4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. ABSOLUTE MAXIMUM RATINGS at TA=25C Parameter Symbol Value Unit Power Dissipation PD 75 mW Reverse Voltage VR 5 V Junction Temperature Tj 115 C Operating Temperature Top -40 to +85 C Storage Temperature Tstg -40 to +85 C DC Forward Current IF 30 mA IFM [1] 155 mA - 3000 V Peak Forward Current Electrostatic Discharge Threshold (HBM) Lead Solder Temperature [2] 260C For 3 Seconds Lead Solder Temperature [3] 260C For 5 Seconds Notes: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. 2. 2mm below package base. 3. 5mm below package base. 4. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity - Ref JEDEC/JESD625-A and JEDEC/J-STD-033. (c) 2018 Kingbright. All Rights Reserved. Spec No: DSAF1861 / 1102013074 Rev No: V.10A Date: 12/14/2018 Page 2 / 4 WP934RS/SRD TECHNICAL DATA SPATIAL DISTRIBUTION RELATIVE INTENSITY vs. WAVELENGTH Red Relative Intensity (a. u.) 100% Ta = 25 C Ta = 25 C 80% 0 -15 15 30 -30 45 -45 60% 60 -60 40% 20% 75 -75 0% 350 400 450 500 550 600 Wavelength (nm) 650 700 750 800 -90 1.0 0.5 0.0 90 1.0 0.5 SUPER BRIGHT RED Forward current (mA) Ta = 25 C 40 30 20 10 1.7 1.9 2.1 2.3 Forward voltage (V) 2.5 Permissible forward current (mA) Luminous intensity normalised at 20mA 50 0 1.5 Forward Current Derating Curve Luminous Intensity vs. Forward Current Ta = 25 C 2.0 1.5 1.0 0.5 0.0 2.5 0 10 20 30 40 Forward current (mA) 50 50 Luminous Intensity vs. Ambient Temperature Luminous intensity normalised at Ta = 25 C Forward Current vs. Forward Voltage 40 30 20 10 0 -40 -20 0 20 40 60 80 100 Ambient temperature (C) 2.5 2.0 1.5 1.0 0.5 0.0 -40 -20 0 20 40 60 80 100 Ambient temperature (C) RECOMMENDED WAVE SOLDERING PROFILE Notes: 1. Recommend pre-heat temperature of 105C or less (as measured with a thermocouple attached to the LED pins) prior to immersion in the solder wave with a maximum solder bath temperature of 260C 2. Peak wave soldering temperature between 245C ~ 255C for 3 sec (5 sec max). 3. Do not apply stress to the epoxy resin while the temperature is above 85C. 4. Fixtures should not incur stress on the component when mounting and during soldering process. 5. SAC 305 solder alloy is recommended. 6. No more than one wave soldering pass. PACKING & LABEL SPECIFICATIONS (c) 2018 Kingbright. All Rights Reserved. Spec No: DSAF1861 / 1102013074 Rev No: V.10A Date: 12/14/2018 Page 3 / 4 WP934RS/SRD PRECAUTIONS Storage Conditions 1. Avoid continued exposure to the condensing moisture environment and keep the product away from rapid transitions in ambient temperature. 2. LEDs should be stored with temperature 30C and relative humidity < 60%. 3. Product in the original sealed package is recommended to be assembled within 72 hours of opening. Product in opened package for more than a week should be baked for 30 (+10/-0) hours at 85 ~ 100C. LED Mounting Method 1. The lead pitch of the LED must match the pitch of the mounting holes on the PCB during component placement. Lead-forming may be required to insure the lead pitch matches the hole pitch. Refer to the figure below for proper lead forming procedures. Note 1-3: Do not route PCB trace in the contact area between the leadframe and the PCB to prevent short-circuits. " " Correct mounting method " x " Incorrect mounting method Lead Forming Procedures 1. During soldering, component covers and holders should leave clearance to avoid placing damaging stress on the LED during soldering. 2. The tip of the soldering iron should never touch the lens epoxy. 3. Through-hole LEDs are incompatible with reflow soldering. 4. If the LED will undergo multiple soldering passes or face other processes where the part may be subjected to intense heat, please check with Kingbright for compatibility. PRECAUTIONARY NOTES 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at https://www.KingbrightUSA.com/ApplicationNotes (c) 2018 Kingbright. All Rights Reserved. Spec No: DSAF1861 / 1102013074 Rev No: V.10A Date: 12/14/2018 Page 4 / 4 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Kingbright: WP934RS/SRD