IRF610B_FP001 - Fairchild Semiconductor

IRF610B/IRFS610B

200V N-Ch annel MOSFET

General Description

These N-Channel enhancement mode power field effect

transistors are produced using Fairchild’s proprietary,

planar, DMOS technology.

This advanced technology has been especially tailored to

minimize on-state resistance, provide superior switching

performance, and withstand high energy pulse in the

avalanche and commutation mode. These devices are well

suited for high efficiency switching DC/DC converters,

switch mode power supplies, DC-AC converters for

uninterrupted power supply and motor control.

Features

• 3.3A, 200V, RDS(on) = 1.5Ω @VGS = 10 V

• Low gate charge ( typical 7.2 nC)

• Low Crss ( typical 6.8 pF)

• Fast switching

• 100% avalanche tested

• Improved dv/dt capability

Absolute Maximum Ratings TC = 25°C unless otherwise noted

* Drain current limited by maximum junction temperature.

Thermal Characte ristics

Symbol Parameter IRF610B IRFS610B Units

VDSS Drain-Source Voltage 200 V

IDDrain Current - Continuous (TC = 25°C) 3.3 3.3 * A

- Continuous (TC = 100°C) 2.1 2.1 * A

IDM Drain Current - Pulsed (Note 1) 10 10 * A

VGSS Gate-Source Voltage ± 30 V

EAS Single Pulsed Avalanche Energy (Note 2) 40 mJ

IAR Avalanche Current (Note 1) 3.3 A

EAR Repetitive Avalanche Energy (Note 1) 3.8 mJ

dv/dt Peak Diode Recovery dv/dt (Note 3) 5.5 V/ns

PDPower Dissipation (TC = 25°C) 38 22 W

- Derate above 25°C 0.31 0.18 W/°C

TJ, TSTG Operating and Storage Temperature Range -55 to +150 °C

TLMaximum lead temperature for soldering purposes,

1/8" from case for 5 seconds 300 °C

Symbol Parameter IRF610B IRFS610B Units

RθJC Thermal Resistance, Junction-to-Case Max. 3.28 5.71 °C/W

RθCS Thermal Resistance, Case-to-Sink Typ. 0.5 -- °C/W

RθJA Thermal Resistance, Junction-to-Ambient Max. 62.5 62.5 °C/W

TO-220

IRF Series

GSD

TO-220F

IRFS Series

Rev. A1, December 2002

IRF610B/IRFS610B

(Note 4)

(Note 4, 5)

(Note 4)

Electrical Characteristics TC = 25°C unless otherwise noted

Notes:

1. Repetitive Rating : Pulse width limited by maximum junction temperature

2. L = 5.5mH, IAS = 3.3A, VDD = 50V, RG = 25 Ω, Starting TJ = 25°C

3. ISD ≤ 3.3A, di/dt ≤ 300A/µs, VDD ≤ BVDSS, Starting TJ = 25°C

4. Pulse Test : Pulse width ≤300µs, Duty cycle ≤2%

5. Essentially independent of operating temperature

Symbol Parame ter Test Condition s Min Typ Max Units

Off Characteristics

BVDSS Drain-S ource Breakdown Voltage VGS = 0 V, ID = 250 µA200 -- -- V

∆BVDSS

/ ∆TJ

Breakdown Voltage Temperature

Coefficient ID = 250 µA, Referenced to 25°C -- 0.2 -- V/°C

IDSS Zero Gate Voltage Drain Current VDS = 200 V, VGS = 0 V -- -- 10 µA

VDS = 160 V, TC = 125°C -- -- 100 µA

IGSSF Gate-Body Leakage Current, Forward VGS = 30 V, VDS = 0 V -- -- 100 nA

IGSSR Gate-Body Leakage Current, Reverse VGS = -30 V, VDS = 0 V -- -- -100 nA

On Characteri st ics

VGS(th) Gate Threshold Voltage VDS = VGS, ID = 250 µA2.0 -- 4.0 V

RDS(on) Static Drain-Source

On-Resistance VGS = 10 V, ID = 1.65 A -- 1.16 1.5 Ω

gFS Forward Transconductance VDS = 40 V, ID = 1.65 A -- 2.4 -- S

Dynamic Characteristics

Ciss Input Capacitance VDS = 25 V, VGS = 0 V,

f = 1.0 MHz

-- 175 225 pF

Coss Output Capacitance -- 30 40 pF

Crss Reverse Transfer Capacitance -- 6.8 9. 0 pF

Switching Characteristics

td(on) Turn-On Delay Time VDD = 100 V, ID = 3.3 A,

RG = 25 Ω

-- 5.2 20 ns

trTurn-On Rise Time -- 35 80 ns

td(off) Turn-Off De l a y Time -- 20 50 ns

tfTurn-Off F a ll Time -- 25 60 ns

QgTotal Gate Charge VDS = 160 V, ID = 3.3 A,

VGS = 10 V

-- 7.2 9.3 nC

Qgs Gate-Source Charge -- 1.3 -- nC

Qgd Gate-Drain Charge -- 3.5 -- nC

Drain-Source Diode Characteristics and Maximum Ratings

ISMaximum Continuous Drain-Source Diode Forward Current -- -- 3.3 A

ISM Maximum Pulsed Drain-Source Diode Forward Current -- -- 10 A

VSD Drain-Source Diode Forward Voltage VGS = 0 V, IS = 3.3 A -- -- 1.5 V

trr Reverse Recovery Time VGS = 0 V, IS = 3.3 A,

dIF / dt = 100 A/µs

-- 106 -- ns

Qrr Reverse Recovery Charge -- 0.37 -- µC

IRF610B/IRFS610B

02468

VDS = 100V

VDS = 40V

VDS = 160V

! Note : ID = 3.3 A

VGS, Gate-Source Voltage [V]

QG, T o ta l G a te C h a rg e [n C ]

02468

VGS = 20V

VGS = 10V

! Note : TJ = 25"

RDS(ON) [#],

Drain-Source O n-Resistance

ID, Drain Current [A]

246810

10-1

100

101

150oC

25oC

-55oC! Notes :

1. VDS = 40V

2. 2 50$s Pulse Test

ID, Drain Current [A]

VGS, Gate-Source Voltage [V]

10-1 100101

10-1

100

101 V GS

Top : 1 5 .0 V

1 0 .0 V

8 .0 V

7 .0 V

6 .5 V

6 .0 V

5 .5 V

Bottom : 5 .0 V

! N otes :

1. 250 $s Pulse Test

2. TC = 25 "

ID, Drain Current [A]

VDS, Drain-Source Voltage [V]

10-1 100101

100

200

300

400

500

Coss

Ciss = Cgs + Cgd (Cds = shorted)

Coss = Cds + Cgd

Crss = Cgd

N o te s :

1 . V GS = 0 V

2 . f = 1 MHz

Crss

Ciss

Capacitance [pF]

VDS, Drain-Source Voltage [V]

0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6

10-1

100

101

150"

! N o tes :

1. VGS = 0V

2. 2 50$s P ulse Te s t

25"

IDR, Reverse Drain Current [A]

VSD, Source-Drain voltage [V]

Typical Characteristics

Figure 5. Capacitance Cha rac te ri st i cs Figure 6. Gate Char ge C haracter is tics

Figure 3. On-Resistanc e Variation vs

Drain Current and Gate Vo ltage Figure 4. Body Diode Fo rwa rd Volt age

Va riat ion with Sour ce Cur r ent

and Temperature

Figure 2. Transfer CharacteristicsFigure 1. On- R egi on Charact er i st ic s

IRF610B/IRFS610B

100101102

10-2

10-1

100

101

10 ms

1 ms 100 µs

Operation in This Area

is Limited by R DS(on)

! Notes :

1. TC = 25 oC

2. TJ = 150 oC

3. Sin g le P u lse

ID, Dr a in Cur re n t [A ]

VDS, Drain-Source Voltage [V]

25 50 75 100 125 150

0.0

0.5

1.0

1.5

2.0

2.5

3.0

3.5

ID, Dr a in Cur re n t [A ]

TC, Case Temperature ["

]

-100 -50 0 50 100 150 200

0.0

0.5

1.0

1.5

2.0

2.5

3.0

! N o te s :

1 . V GS = 10 V

2 . ID = 1.65 A

RDS(ON) , (Normalized)

Drain-Source On-Resistance

TJ, Junction Tem perature [oC]

-100 -50 0 50 100 150 200

0.8

0.9

1.0

1.1

1.2

N o te s :

1 . V GS = 0 V

2 . ID = 250 $A

BV DSS , (N orm alized)

Drain-Source Breakdown Voltage

TJ, Junction Tem pe rature [oC]

Typical Characteristics (Continued)

Figure 9 -1. M aximum Safe O per at in g A re a

for I R F 6 10B

Figure 10. Maximum Drain Current

vs Case Temperature

Figu re 7. Brea kdown Voltage Variation

vs Temperature Figure 8. On-Resistance Va riation

Figure 9-2. M axi m um Safe Op er at ing Area

for IRFS610B

100101102

10-2

10-1

100

101

1 ms

100 m s

10 ms

Operation in This Area

is Limited by R DS(on)

! Notes :

1. TC = 25 oC

2. TJ = 150 oC

3. Single Pulse

ID, Drain Current [A]

VDS, Drain-Source Voltage [V]

IRF610B/IRFS610B

Typical Characteristics (Continued)

10-5 10-4 10-3 10-2 10-1 100101

10-1

100! Notes :

1 . Z%JC(t) = 3.2 8 "/W Ma x .

2 . Duty F a c tor, D = t1/t2

3 . TJM - T C = PDM * Z%JC(t)

s in gle p uls e

D=0.5

0.02

0.2

0.05

0.1

0.01

Z%JC

(t), T he r mal Re s po n s e

t1, Square W ave Pulse Duration [sec]

Figure 11-1. Tr ansient Therma l Res ponse Curve for IRF610B

PDM

10-5 10-4 10-3 10-2 10-1 100101

10-2

10-1

100! Notes :

1 . Z%JC(t) = 5 .71 "/W Ma x .

2 . Duty F a c tor, D = t1/t2

3 . TJM - TC = PDM * Z%JC(t)

s in g le p uls e

D=0.5

0.02

0.2

0.05

0.1

0.01

Z%JC

(t), T he r mal Res p o ns e

t1, S quare W ave Pulse Duration [sec]

Figure 11-2. Transient Th erm al Resp onse Curve IRFS610B

PDM

IRF610B/IRFS610B

Charge

VGS

10V Qg

Qgs Qgd

3mA

VGS

DUT

VDS

300nF

50K&

200nF

12V

Same Type

as DUT

Charge

VGS

10V Qg

Qgs Qgd

3mA

VGS

DUT

VDS

300nF

50K&

200nF

12V

Same Type

as DUT

VGS

VDS

10%

90%

td(on) tr

ton toff

td(off) tf

VDD

10V

VDS RL

DUT

VGS

VDS

10%

90%

td(on) tr

ton toff

td(off) tf

VDD

10V

VDS RL

DUT

VGS

EAS =LI

AS2

----

1--------------------

BVDSS -V

BVDSS

VDD

VDS

BVDSS

t p

VDD

IAS

VDS (t)

ID (t)

Time

10V DUT

t p

EAS =LI

AS2

----

EAS =LI

AS2

----

1--------------------

BVDSS -V

BVDSS

VDD

VDS

BVDSS

t p

VDD

IAS

VDS (t)

ID (t)

Time

10V DUT

t p

Gate Charge Test Circuit & Waveform

Resistive Switching Test Circuit & Waveforms

Unclamped Inductive Switching Test Circuit & W aveforms

IRF610B/IRFS610B

Peak Diode Recover y dv/dt Test Circui t & Waveform s

DUT

VDS

Driver

RGSame Type

as DUT

VGS • dv/dt controlled by RG

•I

SD con trol l ed by pul se period

VDD

ISD

10V

VGS

( Driver )

ISD

( DUT )

VDS

( DUT )

VDD

Body Diode

Forward Voltage Drop

VSD

IFM , Body Diode Forward Current

Body Diode Reverse Current

IRM

Body Diode Recovery dv/dt

di/dt

D = Gate Pulse Width

Gate Pu lse P eri od

--------------------------

DUT

VDS

Driver

RGSame Type

as DUT

VGS • dv/dt controlled by RG

•I

SD con trol l ed by pul se period

VDD

ISD

10V

VGS

( Driver )

ISD

( DUT )

VDS

( DUT )

VDD

Body Diode

Forward Voltage Drop

VSD

IFM , Body Diode Forward Current

Body Diode Reverse Current

IRM

Body Diode Recovery dv/dt

di/dt

D = Gate Pulse Width

Gate Pu lse P eri od

--------------------------

D = Gate Pulse Width

Gate Pu lse P eri od

--------------------------

IRF610B/IRFS610B

Package Dimensions

4.50 ±0.20

9.90 ±0.20

1.52 ±0.10

0.80 ±0.10 2.40 ±0.20

10.00 ±0.20

1.27 ±0.10

ø3.60 ±0.10

(8.70)

2.80 ±0.1015.90 ±0.20

10.08 ±0.30 18.95MAX.

(1.70)

(3.70)(3.00)

(1.46)

(1.00)

(45°)

9.20 ±0.2013.08 ±0.20

1.30 ±0.10

1.30 +0.10

–0.05

0.50 +0.10

–0.05

2.54TYP

[2.54 ±0.20]2.54TYP

[2.54 ±0.20]

TO-220

Dimensions in Millimeters

IRF610B/IRFS610B

Package Dimensions (Continued)

(7.00) (0.70)

MAX1.47

(30°)

3.30 ±0.10

15.80 ±0.20

15.87 ±0.20

6.68 ±0.20

9.75 ±0.30

4.70 ±0.20

10.16 ±0.20

(1.00x45°)

2.54 ±0.20

0.80 ±0.10

9.40 ±0.20

2.76 ±0.20

0.35 ±0.10

ø3.18 ±0.10

2.54TYP

[2.54 ±0.20]2.54TYP

[2.54 ±0.20]

0.50 +0.10

–0.05

TO-220F

Dimensions in Millimeters

DISCLAIMER

FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY

PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY

LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN;

NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.

LIFE SUPPORT POLICY

FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT

DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR

CORPORATION.

As used herein:

1. Life support devices or systems are devic es or syst em s

which, (a) ar e intended for surgical implant into the body,

or (b) support or sustain life, or (c) whose failure to perform

when properly used in accordance with instructions for use

provided in the labeling, can be reasonably expected to

result in significant injury to the user.

2. A critical component is any component of a life support

device or system whose failure to perform can be

reasonably expected to cause the failure of the life support

device or system, or to affect its safety or effectiveness.

PRODUCT STATUS DEFINITIONS

Definition of Terms

Datasheet Identification Product Status Definition

Advance Information Formative or In

Design This datasheet contains the design specifications for

product development. Specifications may change in

any manner without notice.

Preliminary First Production This dat asheet contains preliminary data, and

supplementary data will be published at a later date.

Fairchild Semiconduct or reserv es the right to make

changes at any time without notice in order to improve

design.

No Identification Needed Full Production This datasheet contains final specifications. Fairchild

Semiconductor reserves the right to make changes at

any time without notice in order to improve design.

Obsolete Not In Production This datasheet contains specifications on a product

that has been discontinued by Fairchild semiconductor.

The datasheet is printed for reference information only.

Rev. I1

TRADEMARKS

The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is not

intended to be an exhaustive list of all such trademarks.

FACT™

FACT Quiet series™

FAST®

FASTr™

FRFET™

GlobalOptoisolator™

GTO™

HiSeC™

I2C™

ImpliedDisconnect™

ISOPLANAR™

LittleFET™

MicroFET™

MicroPak™

MICROWIRE™

MSX™

MSXPro™

OCX™

OCXPro™

OPTOLOGIC®

OPTOPLANAR™

PACMAN™

POP™

Power247™

PowerTrench®

QFET™

QS™

QT Optoelectronics™

Quiet Series™

RapidConfigure™

RapidConnect™

SILENT SWITCHER®

SMART START™

SPM™

Stealth™

SuperSOT™-3

SuperSOT™-6

SuperSOT™-8

SyncFET™

TinyLogic™

TruTranslation™

UHC™

UltraFET®

VCX™

ACEx™

ActiveArray™

Bottomless™

CoolFET™

CROSSVOLT™

DOME™

EcoSPARK™

E2CMOS™

EnSigna™

Across the board. Around the world.™

The Power Franchise™

Programmab le Acti ve Droo p™