System Management
Device Overview
January 2009
6
System Management: I2C Peripherals
A family for every common problem
General Purpose Input Output
(GPIO) expanders
More of different types of input or
output, locally or remote
LED Blinkers, dimmers, drivers
Solutions for LED controllability
for direct or in-direct control
Serial ADCs / DACs
Analog control and audio
Tiny and simple Analog-to-Digital
Converters and vice versa
Buffers
Extenders, hubs, repeaters
many devices, large distances and
hazardous circumstances
Temperature Sensors (digital)
Digital temperature information
with internal or external diode
Real Time Clocks (RTCs)
Digital Time and/or calendar
with low power consumption
LCD drivers
Simple displays with a lot of functions
monochrome, character, shapes, dots
DIP / CBT switches
I2C programmable DIP switches and
Cross Bar Technology control (CBT
Switch)
7
System Management: I2C Peripherals
A family for every common problem
Multiplexers and switches
Add advanced I2C bus architecture
devices to allow more devices,
backup, hot-swap
Bus controllers
Add fully featured extra I2C bus
Parallel to I2C master or serial
Bridge ICs with I2C Master
I2C Slave Bridge ICs
I2C Slave devices that add wired
connectivity: SPI Master, UARTs or
DUARTs (dual UARTs)
EEPROMS / E2PROMS/ RAM
Digital permanent memory with long
retention and/or security features
Small Micro Controllers (8-bit)
Add easy custom functionality for
standard tasks
I2C Voltage level translators
Simple multi-configuration level
shifters that support bi-directional and
simultaneous different type of IOs
www.nxp.com/support
33
Bus Architecture
34
I2C-bus –parallel vs serial
Commonly described as “Two-wire bus”
One wire for data, one wire for clock
Serial bus to conserve pins (versus parallel)
Master-Slave hierarchy for simplicity
Good for low to medium speed applications (< 1 MHz)
Logic
V
CC
I2C = Inter-IC
Parallel
Costs EMC, interconnects and pins
Lot of programming
Lots of wires
Saves PCB space
Easily expandable
Better results, no hassle
35
< n data bytes > last data byte
Master Slave
S slave address W Adata Adata
AP
S slave address W Adata Adata APreceiver
transmitter
S slave address R A data A data A P receiver transmitter
< n data bytes >
S = Start condition R = read (active high)
A = Acknowledge A = Not Acknowledge
P = Stop condition W = Write (active low)
Write data
Read data
New devices can be
easily „clipped on to
an existing bus!
Each device is addressed individually by
software with a unique address that can be
modified by hardware pins.
SDA
con-
troller
SCL
GPIO LED LCD
1010A2A1A0R/W EEPROM
A2
A1
A0
1010100R/W
Open drain outputs provide for a “wired-
AND” connection that allows devices to be
added or removed without impact.
The master always
sends the SCL
(clock) signal.
Master Slave
I2C Bus Basics - Address and Data
SCL
SDA
SCL
SDA
36
NXP Introduces Fast-mode Plus
1394.a
CML
RS-422
RS-485
RS-232 RS-423
I2C
0.1
1
10
35
400
655
2500
Data Transfer Rate (Mbps)
010 100 1000
Cable Length (meters)
I2C data can be transmitted at speeds
up to 1 MHz for more bandwidth
3.4 MHz
100 kHz
400 kHz
10X output strength allows
longer distances without
using buffers
Lowers system
cost with more
flexibility
1 MHz
Fm+
P82B96
37
Fast-mode Plus Specifics –PCA96XX
Bus speed DC to 1 MHz fully compatible with existing I2C and SMBus
–Higher bandwidth allows more devices on the bus and more complicated
patterns
Bus drive strength 10x normal I2C I/O Drive
–Drive heavier capacitive load or longer cable lengths
New practical features
–Integrate software reset activates POR with I2C sequence
–Hardware address pins connecting to VCC, GND SCL, SDA allows
up to 64 addresses vs the normal 8 using only three pins
Target market: amusement, back lighting & architectural lighting
I2C-bus Specification UM10204 at www.nxp.com/i2c
38
Maximum bus speed vs capacity
39
New Products
46
System Management
I2C Logic
–Bus Controller
–Temperature Sensor
–EEPROM & DIP Switch
–Multiplexer and Switch
–Voltage Level Translation
Bus Buffer
–Static Level Offset
–Hot Swap
–Long Distance
GTL
–Active transceivers for computing
–Passive voltage level translation
GPIO
–Quasi Bi-Directional output
–Push-pull output
–High Voltage/Automotive
LED
–LED Status Indication
–LED Color Mixing
–LED Signs
47
SE97/98A –Temp Sensor & SPD for DDR3 DIMM
Features
Temperature integrated 2kbit SPD
JEDEC JC42.4 specification compliant
SE97
–3.0 V –3.6 V EEPROM voltage write
and temp sensor operation
–1.7 V –3.6 V EEPROM voltage read
SE98A
–1.7 V –3.6 V temp sensor operation
2x3 DFN, 4x5 TSSOPW
Benefits
Offers wide range of packages: 2x3
HUSON, 3x3 HVSON, and 4x5 TSSOP
Offers lowest height (0.5 mm or
0.8mm) on 2x3 package
MEM MEM MEM MEM
Memory Controller CPU
SMBus EVENT
Memory Bus
DIMM
Memory Module
Temp Sensor only
(SE98A) or Combo
Device (SE97)
48
Differences between LM75A vs LM75B
49
LM75B –SO and TSSOP accuracy vs Temp
SOIC Package TSSOP Package
SO TSSOP
57
System Management
I2C Logic
–Bus Controller
–Temperature Sensor
–EEPROM & DIP Switch
–Multiplexer and Switch
–Voltage Level Translation
Bus Buffer
–Static Level Offset
–Hot Swap
–Long Distance
GTL
–Active transceivers for computing
–Passive voltage level translation
GPIO
–Quasi Bi-Directional output
–Push-pull output
–High Voltage/Automotive
LED
–LED Status Indication
–LED Color Mixing
–LED Signs
58
PCA9507 versus PCA9517/17A
PCA9507 is an upgrade replacement over PCA9517/17A with integrated rise
time accelerator for longer cable HDMI DDC application
Specifically designed for HDMI DDC source applications
A-side has normal voltage swings to interface with any other device
Features PCA9507 PCA9517A PCA9517
A-side with “rise time accelerator” for heavy
load or long cable (over 18 meters)* Yes No No
A-side supply voltage range 2.7V to 5.5V 0.9V to 5.5V 0.9V to 5.5V
ESD HBM 5 kV 5kV 2kV
PCA9507 and PCA9517/17A Comparison
* Note: Longer cable stretches clock low time and requires less than 400 kHz speed operation Not recommended for new designs
59
PCA9507 HDMI DDC Buffer/Extender
Features Benefits
Bidirectional bus buffer Isolate capacitance & noise on DDC line
Rise time accelerator - A-side Extend DDC line > 18 m
Strong A-side driver Increase noise margin on DDC line
5 kV ESD HBM Require no external discrete components
Dual Supplies Permit 5V DDC level shift to 3.3V
DVDR/STB Digital TV
PCA9507
A B
60
PCA9517A –High ESD I2C Bus Buffer
PCA9517Acable
PCA9517A
PCA9517A
PCA9517A
PCA9517A
PCA9517A
PCA9517A
:
PCA9517A
PCA9517A
Redundant Power Supply
Features:
I2C bidirectional buffer
Dual supply rails
–Voltage translation
Normal I/O voltage swing with high
drive on A-side
5 kV ESD HBM
Benefits:
Isolates capacitance and noise for
cable application
Incurs no offset voltage
Redundant Power Supply Ethernet Switch
PCA9517A buffers each end of the cable
Ethernet Switch
..
61
PCA9509 –1.1 V to 3.3/5 V translator
Bidirectional Voltage translation
between 1.1 V and 3.3/5 V without
directional pin
Isolate bus capacitance
ENABLE signal controlled from 1.1 V
or 3.3/5 V side
Ideal for 1.1 V master controlling
3.3/5 V slave or vice-versa
No external pull-up required on the
1.1 V side due to internal current
source
TSSOP8, MSOP8, XSON8 package
B Side
Normal I2C Levels
SMBus/5V
A Side
Static Offset
Low Voltage
Side
Processor
SMBus / Cable
VCC(A) range 1V to VCC(B) -1V
VCC(B) range 3.0 to 5.5V
63
System Management
I2C Logic
–Bus Controller
–Temperature Sensor
–EEPROM & DIP Switch
–Multiplexer and Switch
–Voltage Level Translation
Bus Buffer
–Static Level Offset
–Hot Swap
–Long Distance
GTL
–Active transceivers for computing
–Passive voltage level translation
GPIO
–Quasi Bi-Directional output
–Push-pull output
–High Voltage/Automotive
LED
–LED Status Indication
–LED Color Mixing
–LED Signs
64
PCA9600: Fm+ I2C Bus-Buffer
Fm+
I2C-bus
1 MHz and
60 mA drive
Processor
KEY POINTS
- Longer point-to-point or multi-point architectures
- Isolates capacitance allowing 400 pF on SX/SY
side and 4000 pF on TX/TY side
- I2C-bus logic levels on SX/SY side independent
of supply voltage
- Upgrade for P82B96
Voltage range
Max I2C freq Bus Voltage Range
PCA9600 2.3 - 5.5V w/5V tolerance 1 MHz 2 - 15 V
1 MHz
I2C-bus
FEATURES
- Bidirectional data transfer
- TX/TY outputs have 60 mA sink
capability for driving low-impedance or
high capacitive buses
-1 MHz operation up to 20 meters
GND
Cable
400 pF 4,000 pF
71
System Management
I2C Logic
–Bus Controller
–Temperature Sensor
–EEPROM & DIP Switch
–Multiplexer and Switch
–Voltage Level Translation
Bus Buffer
–Static Level Offset
–Hot Swap
–Long Distance
GTL
–Active transceivers for computing
–Passive voltage level translation
GPIO
–Quasi Bi-Directional output
–Push-pull output
–High Voltage/Automotive
LED
–LED Status Indication
–LED Color Mixing
–LED Signs
72
PCA9574: Level Shifting GPIO with /RESET & /INT
FEATURES
Fast Mode I2C Interface
–400kHz , 400pF bus capacitance
8 Inputs/Outputs
–True Bi-directional Style I/O
–Push-Pull Outputs
–Bus Hold Feature for Inputs
–Programmable Pull-up/Pull-down
Operating Power Supply Voltage Range 1.1V to 3.6V
I/O Voltage Range (VDD(I/O)) = 1.1V to 3.6V
–1.1V, 1.5V, 1.8V, 2.5V, 3.3V±10%
2-Slave Addresses using 1 Address Pin
Bit Maskable Input Interrupts
Hardware/Software Reset
Active Low Open Drain /INT output signals input state change
Low Standby Current <1uA
-40ºC to +85ºC Temp Range
16-TSSOP, 16-SO, 16-HVQFN (3 x 3 x 1 mm) Packages
73
PCA9575: Level Shifting GPIO with /RESET & /INT
FEATURES
Fast Mode I2C Interface
–400kHz , 400pF bus capacitance
16 Inputs/Outputs
–True Bi-directional Style I/O
–Push-Pull Outputs
–Bus Keeper Feature for Inputs
–Programmable Pull-up/Pull-down
Operating Power Supply Voltage Range 1.1V to 3.6V
I/O Voltage Range (VDD(I/O)1, VDD(I/O)2) = 1.1V to 3.6V
–1.1V, 1.5V, 1.8V, 2.5V, 3.3V±10%
Four-Slave Addresses using 2 Address Pins
Bit Maskable Input Interrupts
Hardware/Software Reset
Active Low Open Drain /INT output signals input state change
Low Standby Current <1uA
-40ºC to +85ºC Temp Range
24/28-TSSOP, 24-HVQFN (3x3x1 and 4x4x0.8) Packages
75
FEATURES
I2C Two-wire clip-on feature offers design flexibility
Open drain outputs can sink up to 25 mA
2.3V to 5.5V Supply Voltage
Low Stand-by current < 1μA
Active Low Open-Drain Interrupt Output when input state changes
3-Programmable I2C Address up to 8 devices
Supports I2C Standards 100/400 kHz (Standard/Fast Mode)
Package Availability
Package
Type
Package
Designator
Size
SO24 D 7.5x15.4
TSSOP24 PW 4.4x7.8
HWQFN24 HF 4x4x0.75
PCA9535C:16-bit low power GPIO w/Open Drain
Open drain
PCA9535C
APPLICATIONS
Add additional GPIO Ports for input or output to monitor and command
signal generation.
Keypad and switch control
ACPI power switch
LED control
Signal monitoring
Audio control
Fan control
76
FEATURES
Identical to PCA9539 except for action of /RESET input
I2C Two-wire clip-on feature offers design flexibility
Push Pull outputs can source up to 10 mA and sink up to 25 mA
2.3V to 5.5V Supply Voltage
Low Stand-by current < 1μA
Active Low Open-Drain Interrupt Output when input state changes
3-Programmable I2C Address up to 8 devices
Supports I2C Standards 100/400 kHz (Standard/Fast Mode)
Package Availability
Package
Type
Package
Designator
Size
TSSOP24 PW 4.4x7.8
HVQFN24 BS 4x4x1
PCA9539R:16-bit low power GPIO w/special reset
APPLICATIONS
Add additional GPIO Ports for input or output to monitor
and command signal generation.
Keypad and switch control
ACPI power switch
LED control
Signal monitoring
Audio control
Fan control
PCA9539R –the /RESET pin will only reset the I2C-bus
interface and not the whole device, allowing any chips
being controlled by the outputs to continued to be
controlled even while the I2C-bus interface is reset.
PCA9539R
only
77
System Management
I2C Logic
–Bus Controller
–Temperature Sensor
–EEPROM & DIP Switch
–Multiplexer and Switch
–Voltage Level Translation
Bus Buffer
–Static Level Offset
–Hot Swap
–Long Distance
GTL
–Active transceivers for computing
–Passive voltage level translation
GPIO
–Quasi Bi-Directional output
–Push-pull output
–High Voltage/Automotive
LED
–LED Status Indication
–LED Color Mixing
–LED Signs
78
PCA9701/02
18V Tolerant 16-Bit GPI with /INT
FEATURES
8/16-Bit General Purpose Input Channels
18V Tolerant Inputs
Open Drain /INT output
VCC = 5V
4 MHz SPI Interface
>8kV ESD Protection (HBM)
Temp Range: -40 oC to +125 oC
24-Pin (PCA9701) and 16-Pin (PCA9702)
APPLICATIONS
Automotive –Body Control, Seat Control
AEC-Q100 Compliance > PCA970XPW/Q100
AEC-Q100 Compliance
82
System Management
I2C Logic
–Bus Controller
–Temperature Sensor
–EEPROM & DIP Switch
–Multiplexer and Switch
–Voltage Level Translation
Bus Buffer
–Static Level Offset
–Hot Swap
–Long Distance
GTL
–Active transceivers for computing
–Passive voltage level translation
GPIO
–Quasi Bi-Directional output
–Push-pull output
–High Voltage/Automotive
LED
–LED Status Indication
–LED Color Mixing
–LED Signs
83
LED Driver Roadmap
84
PCA9901 1-Wire Single LED Driver
FEATURES
VCC = 2.1 V t o 5.5 V
1-bit Constant Current LED control
Stand alone blinking capability after “learning” the sequence
One-wire interface
Wake up, Standby and Reset modes
Imax = 20mA (current in the LED set by external resistor)
Ideal for low power applications: Icc <250µA, Istandby <1µA
VALUE PROPOSITION
Off loads the CPU from the LED blinking task
Reduces power consumption during LED blinking task
PCA9901
ISET
LEDOUT
CTRL
CPU
VDD
GND
VBAT
REXT = 22 k
VDD
GND
1Wire
85
FEATURES
Drop-in upgrade for PCA9633
40x power reduction compared to PCA9633
Low Stand-by current < 1μA
Push-Pull Output current rating: 25mA sink, 10mA source
2.3V to 5.5V Supply Voltage
Fixed I2C Address (C4h)
Supports I2C Standards 100/400 kHz (Standard/Fast Mode)
Multifunction: LED On/Off, Bright/Dim, Blinking controls
Blink rate: 40ms to 10.73 seconds
Four 8-Bit PWM Support Individual LED Brightness Control
One 6-Bit PWM Supports Group Dimming Control
Glue less connection to External FETs for higher LED drive
Package Availability
Package
Type
Size (mm)
TSSOP8 DP1 3.1x3.1x1.1
HVSON8 TK 3x3x1
HVSON10 TK2 3x3x1
PCA9632
4-bit Low power, Multifunction I2C LED Controller
APPLICATIONS
Multiple color LED Blinking / status indication
BlueTooth Headphone blinker
Keypad Colorful Fun Lighting
Handset Backlighting, Color mixing
Mobile / Smart Phones
Toys and Handheld Games
I²C Bus
PCA9533
P
W
M
Osc
PCA9533
PWM 1
400 kHz Osc
RGBA Dimmer/Blinker
PWM 2
PWM 4
Global
PWM
Sub1 addr Sub2 addr.
Sub3 addr Group addr.
1 MHz
Addr
C4h
PWM 3
88
SSL3250A –Asynchronous Boost Converter
for Single/Dual High Power LED
Feature:
Output 500mA for flash and 200mA torch, and 20mA separate output indicator with > 85% efficiency
Low side drive LED output up to 9.6V for single or dual LED
Wide input voltage range from 2.7V to 5.5V
Direct HW control or I2C Interface with external resistors to set output current
Strobe and torch input control for low latency for the respective flash and torch mode
TXMASK for push application (email download) to reduce flash current
Detect LED open, short, over-temperature shutdown, output over-voltage protection
3x3x0.8 [mm] HVQFN-16 package Direct Drop in Replacement
for ADP1653 from ADI
PCB Layout
7 mm
7 mm
SSL3250A
89
SSL3252 –Synchronous Boost Converter for
Single/Dual High Power LED
Feature:
Output 500mA flash, 160mA torch/assist light, and separate 10mA indicator with greater than 85% efficiency
High side output up to 8.85V, supporting single or dual LED, and also allowing excellent thermal dissipation
Wide input voltage range from 2.5V to 5.5V
Direct hardware control or I2C interface
Detect inductor broken coil, open, short detection, over-temperature and over current protection
Strobe signal for low latency when flash
2x1.5x0.6 [mm] WLCSP-12 package
SSL3252
5 mm
4 mm
L
COCi
Total PCB Area = 25mm2
90
SSL3250A versus SSL3252
SSL3250A is an asynchronous boost converter for single or dual high power LED
SSL3252 is a synchronous boost converter for single or dual high power LED
FEATURE SSL3250A SSL3252
Drive number of LED in series 1 or 2 1 or 2
Flash/Torch/indicator current 500mA / 200mA / 20mA 400 mA* / 160 mA / 10mA
Assist light NO YES
LED Output Low side drive High side drive
Fixed switching frequency 1.2 MHz 2MHz
Integrate external diode NO YES
Interface Type I2C or Direct I2C or Direct
VIN Range 2.7V to 5.5V 2.5V to 5.5V
Broken coil detection NO YES
Package HVQFN-16 WLCSP-12
Dimension 3x3x0.8 [mm] 2x1.5x0.5 [mm]
ES Availability NOW Q1‟09
RFS NOW Q2‟09
* SSL3252‟s flash current is 400mA @ 2 LED in series, and 500mA @ 1 LED
91
Charge Pump versus Inductor Boost
Inductor boost converter that extends battery life in flash or video mode, is critical for high performance
camera phone
Driving single and multiple LED allows one inductor boost converter to use across multiple platforms
Having multiple LEDs not only gives Xenon Flash physical resemblance, but driving them by one output
allows inductor boost converter provides more and uniform output light, resulting in high quality picture
Feature Charge
Pump Inductor
Boost Comments about Inductor Boost
Extra external
components Fly back
capacitor Inductor* Inductor size is large, but PCB area is primarily dominated by the size
of the LED layout area
Efficiency LOW HIGH Extend battery life that is critical in camera phone
Drive single LED YES YES Driving single and multiple LED allows a single device to use across
multiple platforms
Having multiple LEDs not only gives Xenon Flash physical
resemblance, but driving them by one output provides more and uniform
output light, resulting in taking high quality picture
Drive multiple
LED in series on
same output
NO YES
More Features NO YES TX_MASK reducing output current, prevents over-draining battery in
push application such as downloading email
Separate LED indictor output for video-on
* One additional rectifying diode is required for asynchronous converter
SSL3250A & SSL3252
93
PCA9685 –LED Lighting
RGB-LED
VCC3
drivers
PWM 1
PWM 2
PWM n
PCA9685
OE
Application:
Automotive
Entertainment
Architectural lighting
µC
VCC1
I2C bus, easy
remote control
VCC2
Easy color mixing Larger current /
higher voltage
DC/DC
Converter
PWM
input
VCC4
Drive high efficiency
converters
PCA9685
Global dimming also
with external pin
DC/DC
Converter
UBA3070
Key benefits:
Self-contained PWM on each output, set once, no PWM clock
running across your PCB, reducing EMI
12-bit PWM resolution
PWM frequency adjustable from 40 .. 1000 Hz
94
PCA963X PCA962X
Fast-mode Plus (1 MHz - 4 00 0 pF with SDA I OL 30 mA Yes ←
Voltage range
2.3 - 5.5V ←
7 address pin s 126 devices ←
LED drivers each output programmable at:
◆ Off
◆ On
◆ LED brightness
◆ LED brightness with group dim/blink
yes ←
■ 256-step (8-bit) linear programmable brightness per
LED
yes ←
■ 256-step group brightness control allows general dimming
yes ←
■ 256-step group blinking yes ←
All Call and Sub Calls yes ←
LED IOL 5V、25mA 40V、100mA
Status Now
Shipping 1Q09
PCA96XX LED Controller Migration
110
PCA9922
Constant Current Output LED Driver for large LED signs
The PCA9922 is a pin-to-pin functionally equivalent
5 V alternative for the ST2221A and STP08CDC596.
Features
•25 MHz serial interface
•3.3 V to 5.5 V operation
•8 LED low side constant current outputs
•Global control for the 8 LED outputs
variable between 15 mA to 60 mA
•5 mA to 60 mA maximum current for all 8
output channels set by an external resistor
•Constant current matching at 25 °C,
VDD = 5.0 V
•Bit-to-bit: ±6 %
•Chip-to-chip: ±10 %
•Gradual turn-on/turn-off output to limit EMI
•Error detection mode for line open, output
short to ground, LED open and LED short
•-40 °C to +85 °C operation
118
Release History
122
NEW PRODUCT INTRODUCTION: System Management
FAMILY or PART # FUNCTION RFS DATE COMMENT
PCA9549BS 8-bit CBT controlled by I2C-bus Feb 07 Release in HVQFN package
GTL2012 2 bit GTL to LVTTL Feb 07 ½ of GTL2005 or GTL2014 for computing
PCA9545B/45C 4 channel switch Mar 07 Alt address allows more devices on bus
GTL2003 8-bit Level Translator Mar 07 Offered in small DQFN package for computing
PCA9534BS3 8-bit GPIO Apr 07 Smaller HVQFN package
PCA9509GM Low Voltage Bus Buffer Jun 07 Offering in small package for computing
PCA9535HF/55HF 16-bit GPIO Jun 07 Offered in thinner HVQFN package
PCA9543B/43C 4 channel switch Jun 07 Alt address allows more devices on bus
GTL2018 8 bit GTL to LVTTL Jun 07 2X of GTL2005 or GTL2014 for computing
GTL2107 12-bit GTL Interface Jun 07 For Intel Xeon processor/chipset interface
PCA9518A Expandable 5 channel hub Jun 07 Fix Hi-Z (match TI) and make 2.3 to 3.6V operation
PCA9701 16 bit SPI GPI 18V tol Aug 07 For automotive relay pwr control, will be AEC-Q100
SE97 DDR3 DIMM TS with SPD Sept 07 +/-1 oC local TS w/2Kbit EEPROM
PCA9535C 16-bit GPIO Sept 07 Upper transistor disconnected/open drain I/O
PCA9632 4-bit LED Controller Sept 07 40X power reduction from PCA9633, for mobile
GTL2002DP/Q900 2-bit Level Translator Dec 07 Automotive AEC-Q100 qualification device
PCA9600 Fm+ Bus Buffer Dec 07 1 MHz version of P82B96
PCA9517A Bus Buffers Dec 07 Fix pin 3 ESD cell/latch up & need device higher Vil
PCA9507 Bus Buffers Dec 07 Level trans, isolate capacitance, rise time accelerator
System Management 2007
123
NEW PRODUCT INTRODUCTION: System Management
FAMILY or PART # FUNCTION RFS DATE COMMENT
PCA9625 16-bit LED Controller Jan 08 100 mA/24V Use FET for HV for Slot Machine
PCA9306DC1 2-bit Level Translator Feb 08 Small VSSOP package to match TI DCU package
PCA9508 Hot Swap Bus Buffer Mar 08 PCA9517A w/hot swap connect feature (like PCA9512A)
PCA9574 8-bit Low Voltage GPIO Mar 08 Separate VCC pin for I/O voltage translation 1.1 - 3.6V
PCA9632/02 4-bit LED controller Apr 08 Two address in version of PCA9632 allow 4 per bus
PCA9685 16-bit LED Controller Jun 08 12-bit accuracy (4K steps) for LCD TV Backlighting
PCA9539R 16-bit GPIO with INT/Reset Aug 08 Improved version of PCA9539 doesn‟t reset I/O state
SE97TL/TP DDR3 DIMM TS with SPD Sept 08 +/-1 oC local TS w/2Kbit EEPROM in 2 x 3 MLP package
PCA9702 8 bit SPI GPI 18V tol Sep 08 For automotive relay pwr control, may be AEC-Q100
PCA9575 16-bit Low Voltage GPIO Oct 08 Separate VCC pins for I/Os allows voltage trans 1.1 –3.6V
LM75B Low cost industrial temp sensor Nov 08 +/-2 oC local TS with interrupt output
SSL3150AHN Dual LED Flash - Sink Dec 08 Mobile - 500 mA for two LEDs in series
System Management 2008
124
NEW PRODUCT INTRODUCTION: System Management
FAMILY or PART # FUNCTION RFS DATE COMMENT
PCA9922 8-bit Constant current LED Driver Jan 09 For LED bill board, serial interface
PCA9622 16-bit LED Controller 1Q 09 100 mA/40V LED control, Fast-mode Plus interface
SE98A DDR3 DIMM TS without SPD 1Q 09 +/-1 oC local TS VCC range 1.7 –3.6V
PCA9624 8-bit LED Controller 1Q 09 100 mA/40V LED control, Fast-mode Plus interface
PCA9626 24-bit LED Controller 2Q 09 100 mA/40V LED control, Fast-mode Plus interface
SSL3252UK Dual LED Flash - Source 2Q 09 Mobile - 500 mA for two LEDs in series - CSP
PCA9901 1 wire LED controller 2Q 09 Mobile, low Idd, current source 20 mA, 3 pattern sequence
PCA9527 3 ch Buffer w/rise time accelerator 2Q 09 For HDMI DDC & CEC connections (or SCL/SDA & INT)
System Management 2009 –1H
132
Support
133
General: http://www.semiconductors.nxp.com/support
I2C Logic:
http://www.nxp.com/i2c
I2C.Support@nxp.com (E-mail Support)
http://forums.nxp.com/forums/viewforum.php?f=6 (Discussion Forum)
All other devices
http://www.standardics.nxp.com/interface/
Interface.Support@nxp.com (E-mail Support)
Interface Products Internet Support
135