LM35 Precision Centigrade Temperature Sensors General Description The LM35 series are precision integrated-circuit temperature sensors, whose output voltage is linearly proportional to the Celsius (Centigrade) temperature. The LM35 thus has an advantage over linear temperature sensors calibrated in Kelvin, as the user is not required to subtract a large constant voltage from its output to obtain convenient Centigrade scaling. The LM35 does not require any external calibration or trimming to provide typical accuracies of 14C at room temperature and 34C over a full -55 to +150C temperature range. Low cost is assured by trimming and calibration at the wafer level. The LM35's low output impedance, linear output, and precise inherent calibration make interfacing to readout or control circuitry especially easy. It can be used with single power supplies, or with plus and minus supplies. As it draws only 60 A from its supply, it has very low self-heating, less than 0.1C in still air. The LM35 is rated to operate over a -55 to +150C temperature range, while the LM35C is rated for a -40 to +110C range (-10 with improved accuracy). The LM35 series is available pack- aged in hermetic TO-46 transistor packages, while the LM35C, LM35CA, and LM35D are also available in the plastic TO-92 transistor package. The LM35D is also available in an 8-lead surface mount small outline package and a plastic TO-220 package. Features n n n n n n n n n n n Calibrated directly in Celsius (Centigrade) Linear + 10.0 mV/C scale factor 0.5C accuracy guaranteeable (at +25C) Rated for full -55 to +150C range Suitable for remote applications Low cost due to wafer-level trimming Operates from 4 to 30 volts Less than 60 A current drain Low self-heating, 0.08C in still air Nonlinearity only 14C typical Low impedance output, 0.1 for 1 mA load Typical Applications DS005516-4 DS005516-3 FIGURE 1. Basic Centigrade Temperature Sensor (+2C to +150C) Choose R1 = -VS/50 A V OUT =+1,500 mV at +150C = +250 mV at +25C = -550 mV at -55C FIGURE 2. Full-Range Centigrade Temperature Sensor (c) 2000 National Semiconductor Corporation DS005516 www.national.com LM35 Precision Centigrade Temperature Sensors November 2000 LM35 Connection Diagrams TO-46 Metal Can Package* SO-8 Small Outline Molded Package DS005516-1 DS005516-21 *Case is connected to negative pin (GND) N.C. = No Connection Order Number LM35H, LM35AH, LM35CH, LM35CAH or LM35DH See NS Package Number H03H Top View Order Number LM35DM See NS Package Number M08A TO-92 Plastic Package TO-220 Plastic Package* DS005516-2 Order Number LM35CZ, LM35CAZ or LM35DZ See NS Package Number Z03A DS005516-24 *Tab is connected to the negative pin (GND). Note: The LM35DT pinout is different than the discontinued LM35DP. Order Number LM35DT See NS Package Number TA03F www.national.com 2 TO-92 and TO-220 Package, (Soldering, 10 seconds) 260C SO Package (Note 12) Vapor Phase (60 seconds) 215C Infrared (15 seconds) 220C ESD Susceptibility (Note 11) 2500V Specified Operating Temperature Range: TMIN to T MAX (Note 2) LM35, LM35A -55C to +150C LM35C, LM35CA -40C to +110C LM35D 0C to +100C If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage Output Voltage Output Current Storage Temp.; TO-46 Package, TO-92 Package, SO-8 Package, TO-220 Package, Lead Temp.: TO-46 Package, (Soldering, 10 seconds) +35V to -0.2V +6V to -1.0V 10 mA -60C -60C -65C -65C to to to to +180C +150C +150C +150C 300C Electrical Characteristics (Notes 1, 6) LM35A Parameter Conditions Tested Typical T MINTATMAX 0.2 0.3 0.4 0.4 0.18 T MINTATMAX +10.0 Accuracy T A =+25C (Note 7) T A =-10C T A =TMAX T A =TMIN Nonlinearity LM35CA Design Limit Limit (Note 4) (Note 5) 0.5 1.0 1.0 0.35 Tested Typical 0.2 0.3 0.4 0.4 0.15 Design Units Limit Limit (Max.) (Note 4) (Note 5) 0.5 C 1.0 1.0 C C 1.5 0.3 C +9.9, mV/C C (Note 8) Sensor Gain (Average Slope) +9.9, +10.0 +10.1 Load Regulation T A =+25C (Note 3) 0IL1 mA T MINTATMAX Line Regulation T A =+25C (Note 3) 4VV S30V 0.4 0.5 0.01 0.02 Quiescent Current V S =+5V, +25C 56 (Note 9) V S =+5V 105 V S =+30V, +25C 56.2 V S =+30V 105.5 +10.1 1.0 0.1 0.4 0.5 0.01 0.02 131 91 3.0 0.05 67 56 68 56.2 133 91.5 1.0 mV/mA 3.0 0.05 mV/mA mV/V 0.1 67 mV/V A 114 A 116 A 68 A Change of 4VVS30V, +25C 0.2 Quiescent Current 4VV S30V 0.5 2.0 0.5 2.0 A +0.39 +0.5 +0.39 +0.5 A/C +1.5 +2.0 +1.5 +2.0 C 1.0 0.2 1.0 A (Note 3) Temperature Coefficient of Quiescent Current Minimum Temperature In circuit of for Rated Accuracy Figure 1, IL =0 Long Term Stability T J =TMAX, for 0.08 0.08 C 1000 hours 3 www.national.com LM35 Absolute Maximum Ratings (Note 10) LM35 Electrical Characteristics (Notes 1, 6) LM35 Parameter Conditions Design Limit Limit (Note 4) (Note 5) Typical Accuracy, T A =+25C LM35, LM35C T A =-10C (Note 7) T A =TMAX 0.4 0.5 0.8 0.8 T A =TMIN Accuracy, LM35D (Note 7) LM35C, LM35D Tested 1.0 1.5 1.5 T A =+25C TA =TMAX TA =TMIN Nonlinearity T MINTATMAX 0.3 T MINTATMAX +10.0 0.5 Typical 0.4 0.5 0.8 0.8 0.6 0.9 0.9 0.2 Tested Design Units Limit Limit (Max.) (Note 4) (Note 5) 1.0 C 1.5 1.5 2.0 1.5 C C C C 2.0 2.0 0.5 C +9.8, mV/C C C (Note 8) Sensor Gain (Average Slope) +9.8, +10.0 +10.2 0.4 0.5 0.01 0.02 2.0 V S =+5V, +25C 56 80 V S =+5V 105 V S =+30V, +25C 56.2 V S =+30V 105.5 Load Regulation T A =+25C (Note 3) 0IL1 mA T MINTATMAX Line Regulation T A =+25C (Note 3) 4VV S30V Quiescent Current (Note 9) +10.2 5.0 0.1 0.2 158 82 0.4 0.5 0.01 0.02 2.0 56 80 161 0.1 mV/V A 138 82 91.5 mV/mA mV/V 0.2 91 56.2 mV/mA 5.0 A A 141 A Change of 4VVS30V, +25C 0.2 Quiescent Current 4VV S30V 0.5 3.0 0.5 3.0 A +0.39 +0.7 +0.39 +0.7 A/C +1.5 +2.0 +1.5 +2.0 C 2.0 0.2 2.0 A (Note 3) Temperature Coefficient of Quiescent Current Minimum Temperature In circuit of for Rated Accuracy Figure 1, IL =0 Long Term Stability T J =TMAX, for 0.08 0.08 C 1000 hours Note 1: Unless otherwise noted, these specifications apply: -55CTJ+150C for the LM35 and LM35A; -40TJ+110C for the LM35C and LM35CA; and 0TJ+100C for the LM35D. VS =+5Vdc and ILOAD =50 A, in the circuit of Figure 2. These specifications also apply from +2C to TMAX in the circuit of Figure 1. Specifications in boldface apply over the full rated temperature range. Note 2: Thermal resistance of the TO-46 package is 400C/W, junction to ambient, and 24C/W junction to case. Thermal resistance of the TO-92 package is 180C/W junction to ambient. Thermal resistance of the small outline molded package is 220C/W junction to ambient. Thermal resistance of the TO-220 package is 90C/W junction to ambient. For additional thermal resistance information see table in the Applications section. Note 3: Regulation is measured at constant junction temperature, using pulse testing with a low duty cycle. Changes in output due to heating effects can be computed by multiplying the internal dissipation by the thermal resistance. Note 4: Tested Limits are guaranteed and 100% tested in production. Note 5: Design Limits are guaranteed (but not 100% production tested) over the indicated temperature and supply voltage ranges. These limits are not used to calculate outgoing quality levels. Note 6: Specifications in boldface apply over the full rated temperature range. Note 7: Accuracy is defined as the error between the output voltage and 10mv/C times the device's case temperature, at specified conditions of voltage, current, and temperature (expressed in C). Note 8: Nonlinearity is defined as the deviation of the output-voltage-versus-temperature curve from the best-fit straight line, over the device's rated temperature range. Note 9: Quiescent current is defined in the circuit of Figure 1. Note 10: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not apply when operating the device beyond its rated operating conditions. See Note 1. Note 11: Human body model, 100 pF discharged through a 1.5 k resistor. Note 12: See AN-450 "Surface Mounting Methods and Their Effect on Product Reliability" or the section titled "Surface Mount" found in a current National Semiconductor Linear Data Book for other methods of soldering surface mount devices. www.national.com 4 LM35 Typical Performance Characteristics Thermal Resistance Junction to Air Thermal Response in Still Air Thermal Time Constant DS005516-26 DS005516-25 Thermal Response in Stirred Oil Bath DS005516-27 Minimum Supply Voltage vs. Temperature Quiescent Current vs. Temperature (In Circuit of Figure 1.) DS005516-29 DS005516-28 DS005516-30 Quiescent Current vs. Temperature (In Circuit of Figure 2.) Accuracy vs. Temperature (Guaranteed) Accuracy vs. Temperature (Guaranteed) DS005516-32 DS005516-33 DS005516-31 5 www.national.com LM35 Typical Performance Characteristics (Continued) Noise Voltage Start-Up Response DS005516-34 DS005516-35 The TO-46 metal package can also be soldered to a metal surface or pipe without damage. Of course, in that case the V- terminal of the circuit will be grounded to that metal. Alternatively, the LM35 can be mounted inside a sealed-end metal tube, and can then be dipped into a bath or screwed into a threaded hole in a tank. As with any IC, the LM35 and accompanying wiring and circuits must be kept insulated and dry, to avoid leakage and corrosion. This is especially true if the circuit may operate at cold temperatures where condensation can occur. Printed-circuit coatings and varnishes such as Humiseal and epoxy paints or dips are often used to insure that moisture cannot corrode the LM35 or its connections. These devices are sometimes soldered to a small light-weight heat fin, to decrease the thermal time constant and speed up the response in slowly-moving air. On the other hand, a small thermal mass may be added to the sensor, to give the steadiest reading despite small deviations in the air temperature. Applications The LM35 can be applied easily in the same way as other integrated-circuit temperature sensors. It can be glued or cemented to a surface and its temperature will be within about 0.01C of the surface temperature. This presumes that the ambient air temperature is almost the same as the surface temperature; if the air temperature were much higher or lower than the surface temperature, the actual temperature of the LM35 die would be at an intermediate temperature between the surface temperature and the air temperature. This is expecially true for the TO-92 plastic package, where the copper leads are the principal thermal path to carry heat into the device, so its temperature might be closer to the air temperature than to the surface temperature. To minimize this problem, be sure that the wiring to the LM35, as it leaves the device, is held at the same temperature as the surface of interest. The easiest way to do this is to cover up these wires with a bead of epoxy which will insure that the leads and wires are all at the same temperature as the surface, and that the LM35 die's temperature will not be affected by the air temperature. Temperature Rise of LM35 Due To Self-heating (Thermal Resistance,JA) TO-46, TO-46*, TO-92, TO-92**, SO-8 SO-8** TO-220 no heat sink small heat fin no heat sink small heat fin no heat sink small heat fin no heat sink Still air 400C/W 100C/W 180C/W 140C/W 220C/W 110C/W 90C/W Moving air 100C/W 40C/W 90C/W 70C/W 105C/W 90C/W 26C/W Still oil 100C/W 40C/W 90C/W 70C/W Stirred oil 50C/W 30C/W 45C/W 40C/W (Clamped to metal, Infinite heat sink) (24C/W) (55C/W) *Wakefield type 201, or 1" disc of 0.020" sheet brass, soldered to case, or similar. **TO-92 and SO-8 packages glued and leads soldered to 1" square of 1/16" printed circuit board with 2 oz. foil or similar. www.national.com 6 LM35 Typical Applications DS005516-19 FIGURE 3. LM35 with Decoupling from Capacitive Load DS005516-6 FIGURE 6. Two-Wire Remote Temperature Sensor (Output Referred to Ground) DS005516-20 FIGURE 4. LM35 with R-C Damper CAPACITIVE LOADS Like most micropower circuits, the LM35 has a limited ability to drive heavy capacitive loads. The LM35 by itself is able to drive 50 pf without special precautions. If heavier loads are anticipated, it is easy to isolate or decouple the load with a resistor; see Figure 3. Or you can improve the tolerance of capacitance with a series R-C damper from output to ground; see Figure 4. When the LM35 is applied with a 200 load resistor as shown in Figure 5, Figure 6 or Figure 8 it is relatively immune to wiring capacitance because the capacitance forms a bypass from ground to input, not on the output. However, as with any linear circuit connected to wires in a hostile environment, its performance can be affected adversely by intense electromagnetic sources such as relays, radio transmitters, motors with arcing brushes, SCR transients, etc, as its wiring can act as a receiving antenna and its internal junctions can act as rectifiers. For best results in such cases, a bypass capacitor from VIN to ground and a series R-C damper such as 75 in series with 0.2 or 1 F from output to ground are often useful. These are shown in Figure 13, Figure 14, and Figure 16. DS005516-7 FIGURE 7. Temperature Sensor, Single Supply, -55 to +150C DS005516-8 FIGURE 8. Two-Wire Remote Temperature Sensor (Output Referred to Ground) DS005516-5 FIGURE 5. Two-Wire Remote Temperature Sensor (Grounded Sensor) DS005516-9 FIGURE 9. 4-To-20 mA Current Source (0C to +100C) 7 www.national.com LM35 Typical Applications (Continued) DS005516-11 FIGURE 11. Centigrade Thermometer (Analog Meter) DS005516-10 FIGURE 10. Fahrenheit Thermometer DS005516-12 FIGURE 12. Fahrenheit ThermometerExpanded Scale Thermometer (50 to 80 Fahrenheit, for Example Shown) DS005516-13 FIGURE 13. Temperature To Digital Converter (Serial Output) (+128C Full Scale) DS005516-14 FIGURE 14. Temperature To Digital Converter (Parallel TRI-STATETM Outputs for Standard Data Bus to P Interface) (128C Full Scale) www.national.com 8 LM35 Typical Applications (Continued) DS005516-16 * =1% or 2% film resistor Trim RB for VB =3.075V Trim RC for VC =1.955V Trim RA for VA =0.075V + 100mV/C x Tambient Example, VA =2.275V at 22C FIGURE 15. Bar-Graph Temperature Display (Dot Mode) DS005516-15 FIGURE 16. LM35 With Voltage-To-Frequency Converter And Isolated Output (2C to +150C; 20 Hz to 1500 Hz) 9 www.national.com LM35 Block Diagram DS005516-23 www.national.com 10 LM35 Physical Dimensions inches (millimeters) unless otherwise noted TO-46 Metal Can Package (H) Order Number LM35H, LM35AH, LM35CH, LM35CAH, or LM35DH NS Package Number H03H SO-8 Molded Small Outline Package (M) Order Number LM35DM NS Package Number M08A 11 www.national.com LM35 Physical Dimensions inches (millimeters) unless otherwise noted (Continued) Power Package TO-220 (T) Order Number LM35DT NS Package Number TA03F www.national.com 12 LM35 Precision Centigrade Temperature Sensors Physical Dimensions inches (millimeters) unless otherwise noted (Continued) TO-92 Plastic Package (Z) Order Number LM35CZ, LM35CAZ or LM35DZ NS Package Number Z03A LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: support@nsc.com www.national.com National Semiconductor Europe Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: ap.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.