19-4420; Rev 1; 6/09 KIT ATION EVALU LE B A IL A AV Ultrasound VGA Integrated with CW Octal Mixer Features The MAX2036 8-channel variable-gain amplifier (VGA) and programmable octal mixer array is designed for high linearity, high dynamic range, and low-noise performance targeting ultrasound imaging and Doppler applications. Each amplifier features differential inputs and outputs and a total gain range of 50dB (typ). In addition, the VGAs offer very low output-referred noise performance suitable for interfacing with 10-bit ADCs. The MAX2036 VGA is optimized for less than 0.5dB absolute gain error to ensure minimal channel-to-channel ultrasound beamforming focus error. The device's differential outputs are designed to directly drive ultrasound ADCs through an external passive anti-aliasing filter. A switchable clamp is also provided at each amplifier's output to limit the output signals, thereby preventing ADC overdrive or saturation. Dynamic performance of the device is optimized to reduce distortion to support second-harmonic imaging. The device achieves a second-harmonic distortion specification of -62dBc at VOUT = 1.5VP-P and fIN = 5MHz, and an ultrasound-specific* two-tone third-order intermodulation distortion specification of -52dBc at VOUT = 1.5VP-P and fIN = 5MHz. The MAX2036 also integrates an octal quadrature mixer array and programmable LO phase generators for a complete CW beamforming solution. The LO phase selection for each channel can be programmed using a digital serial interface and a single high-frequency clock or the LOs for each complex mixer pair can be directly driven using separate 4 x LO clocks. The serial interface is designed to allow multiple devices to be easily daisy-chained in order to minimize program interface wiring. The LO phase dividers can be programmed to allow 4, 8, or 16 quadrature phases. The input path of each CW mixer consists of a selectable lowpass filter for optimal CWD noise performance. The outputs of the mixers are summed into I and Q differential current outputs. The mixers and LO generators are designed to have exceptionally low noise performance of -155dBc/Hz at 1kHz offset from a 1.25MHz carrier. The MAX2036 operates from a +5.0V power supply, consuming only 120mW/channel in VGA mode and 269mW/channel in normal power CW mode. A lowpower CW mode is also available and consumes only 226mW/channel. The device is available in a lead-free 100-pin TQFP package (14mm x 14mm) with an exposed pad. Electrical performance is guaranteed over a 0C to +70C temperature range. o 8-Channel Configuration o High Integration for Ultrasound Imaging Applications o Pin Compatible with the MAX2035 Ultrasound VGA VGA Features o Maximum Gain, Gain Range, and Output-Referred Noise Optimized for Interfacing with 10-Bit ADCs Maximum Gain of 39.5dB Total Gain Range of 50dB 60nV/Hz Ultra-Low Output-Referred Noise at 5MHz o 0.5dB Absolute Gain Error o 120mW Consumption per Channel o Switchable Output VGA Clamp Eliminating ADC Overdrive o Fully Differential VGA Outputs for Direct ADC Drive o Variable Gain Range Achieves 50dB Dynamic Range o -62dBc HD2 at VOUT = 1.5VP-P and fIN = 5MHz o Two-Tone Ultrasound-Specific* IMD3 of -52dBc at VOUT = 1.5VP-P and fIN = 5MHz CWD Mixer Features o Low Mixer Noise of -155dBc/Hz at 1kHz Offset from 1.25MHz Carrier o Serial-Programmable LO Phase Generator for 4, 8, 16 LO Quadrature Phase Resolution o Optional Individual Channel 4 x fLO LO Input Drive Capability o 269mW Power Consumption per Channel (Normal Power Mode) and 226mW Power Consumption per Channel (Low-Power Mode) Applications Ultrasound Imaging Sonar Ordering Information PART TEMP RANGE MAX2036CCQ+D 0C to +70C PIN-PACKAGE 100 TQFP-EP MAX2036CCQ+TD 0C to +70C 100 TQFP-EP +Denotes a lead(Pb)-free/RoHS-compliant package. T = Tape and reel. D = Dry packing. EP = Exposed pad. *See the Ultrasound-Specific IMD3 Specification in the Applications Information section. Pin Configuration appears at end of data sheet. ________________________________________________________________ Maxim Integrated Products 1 For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim's website at www.maxim-ic.com. MAX2036 General Description MAX2036 Ultrasound VGA Integrated with CW Octal Mixer ABSOLUTE MAXIMUM RATINGS VCC, VREF to GND .................................................-0.3V to +5.5V Any Other Pins to GND...............................-0.3V to (VCC + 0.3V) CW Mixer Output Voltage to GND (CW_IOUT+, CW_IOUT-, CW_QOUT+, CW_QOUT-) ................................................13V VGA Differential Input Voltage (VGIN_+, VGIN_-)............8.0VP-P Analog Gain Control Differential Input Voltage (VG_CTL+, VG_CTL-) ..................................................8.0VP-P CW Mixer Differential Input Voltage (CWIN_+, CWIN_-).......................................................8.0VP-P CW Mixer LVDS LO Differential Input Voltage..................8.0VP-P Continuous Power Dissipation (TA = +70C) 100-Pin TQFP (derated 45.5mW/C above +70C)..3636.4mW Operating Temperature Range...............................0C to +70C Junction Temperature ......................................................+150C JC (Note 1) .....................................................................+2C/W JA (Note 1)....................................................................+22C/W Storage Temperature Range .............................-40C to +150C Lead Temperature (soldering, 10s) .................................+300C Note 1: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a fourlayer board. For detailed information on package thermal considerations, refer to www.maxim-ic.com/thermal-tutorial. Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. DC ELECTRICAL CHARACTERISTICS--VGA MODE (Figure 7, VCC = VREF = 4.75V to 5.25V, VCM = (3/5)VREF, TA = 0C to +70C, VGND = 0V, LOW_PWR = 0, M4_EN = 0, CW_FILTER = 0 or 1, TEST_MODE = 0, PD = 0, CW_VG = 1, CW_M1 = 0, CW_M2 = 0, no RF signals applied, capacitance to GND at each of the VGA differential outputs is 60pF, differential capacitance across the VGA outputs is 10pF, RL = 1k, CW mixer outputs pulled up to +11V through four separate 0.1% 115 resistors, all CW channels programmed off. Typical values are at VCC = VREF = 5V, TA = +25C, unless otherwise noted.) (Note 2) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS 4.75 5 5.25 V 4.75 5 5.25 V PD = 0 204 231 PD =1 27 33 VGA MODE Supply Voltage Range VCC VCC External Reference Voltage Range VREF (Note 3) Refers to VCC supply current plus VREF current Total Power-Supply Current mA VCC Supply Current IVCC 192 216 mA VREF Current IREF 12 15 mA Refers to VCC supply current 24 27 mA Minimum gain +2 Maximum gain -2 Current Consumption per Amplifier Channel Differential Analog Control Voltage Range Differential Analog Control Common-Mode Voltage VCM 2.85 Analog Control Input Source/Sink Current VP-P 3 3.15 V 4.5 5 mA 0.8 V LOGIC INPUTS CMOS Input High Voltage VIH CMOS Input Low Voltage VIL 2 2.3 _______________________________________________________________________________________ V Ultrasound VGA Integrated with CW Octal Mixer (Figure 7, VCC = VREF = 4.75V to 5.25V, TA = 0C to +70C, VGND = 0V, LOW_PWR = 0, M4_EN = 0, CW_FILTER = 0 or 1, TEST_MODE = 0, PD = 0, CW_VG = 0, CW_M1 = 0, CW_M2 = 0, no RF signals applied, capacitance to GND at each of the VGA differential outputs is 60pF, differential capacitance across the VGA outputs is 10pF, RL = 1k, CW mixer outputs pulled up to +11V through four separate 0.1% 115 resistors. Typical values are at VCC = VREF = 5V, TA = +25C, unless otherwise noted.) (Note 2) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS CW MIXER MODE Current in Full-Power Mode 5V VCC Supply ICC_FP Refers to VCC supply current (all 8 channels) 245 265 mA Current in Full-Power Mode 11V VMIX Supply IMIX_FP Refers to VMIX supply current (all 8 channels) 106 120 mA Current in Full-Power Mode 5V VREF Supply IREF_FP Refers to VREF supply current (all 8 channels) 17 21 mA PDISS_FP Total power dissipation (all 8 channels including both 5V (VCC and VREF) and 11V mixer pullup supply power dissipation in the device) (Note 4) 2.15 2.41 W Power Dissipation in Full-Power Mode Current in Low-Power Mode 5V VCC Supply ICC_LP LOW_PWR = 1; refers to VCC supply current (all 8 channels) 245 265 mA Current in Low-Power Mode 11V VMIX Supply IMIX_LP LOW_PWR = 1; refers to VMIX supply current (all 8 channels) 53 60 mA Current in Low-Power Mode 5V VREF Supply IREF_LP LOW_PWR = 1; refers to VREF supply current (all 8 channels) 17 21 mA LOW_PWR = 1; total power dissipation (all 8 channels including both 5V (VCC and VREF) and 11V mixer pullup supply power dissipation in the device) (Note 4) 1.81 2.06 W Mixer LVDS LO Input CommonMode Voltage Modes 1 and 2 (Note 5) 1.25 0.2 V LVDS LO Differential Input Voltage Modes 1 and 2 700 mVP-P LVDS LO Input Common-Mode Current Per pin 150 LVDS LO Differential Input Resistance Modes 1 and 2 (Note 6) 30 Mixer IF Common-Mode Output Current Common-mode current in each of the differential mixer outputs (Note 7) DATA Output High Voltage DOUT voltage when terminated in DIN (daisy chain) (Note 8) DATA Output Low Voltage DOUT voltage when terminated in DIN (daisy chain) (Note 8) Power Dissipation in Low-Power Mode PDISS_LP 200 3.25 200 A k 3.75 4.5 mA V 0.5 V _______________________________________________________________________________________ 3 MAX2036 DC ELECTRICAL CHARACTERISTICS--CM MIXER MODE MAX2036 Ultrasound VGA Integrated with CW Octal Mixer AC ELECTRICAL CHARACTERISTICS--VGA MODE (Figure 7, VCC = VREF = 4.75V to 5.25V, VCM = (3/5)VREF, TA = 0C to +70C, VGND = 0V, LOW_PWR = 0, M4_EN = 0, CW_FILTER = 1, TEST_MODE = 0, PD = 0, CW_VG = 1, CW_M1 = 0, CW_M2 = 0, VG_CLAMP_MODE = 1, fRF = fLO/16 = 5MHz, capacitance to GND at each of the VGA differential outputs is 60pF, differential capacitance across the VGA outputs is 10pF, RL = 1k, CW mixer outputs pulled up to +11V through four separate 0.1% 115 resistors, differential mixer inputs are driven from a low-impedance source. Typical values are at VCC = VREF = 5V, TA = +25C, unless otherwise noted.) (Note 2) PARAMETER SYMBOL CONDITIONS MIN CW_VG set from logic 1 to 0 or from 0 to 1 (Note 9) Mode Select Response Time TYP MAX 2 UNITS s VGA MODE Large-Signal Bandwidth f-3dB Differential Input Resistance RIN Input Effective Capacitance CIN VOUT = 1.5VP-P, 3dB bandwidth, gain = 20dB Differential output capacitance is 10pF, capacitance to GND at each single-ended output is 60pF, RL = 1k 17 No capacitive load, RL = 1k 22 MHz 170 fRF = 10MHz, each input to ground 200 15 230 pF 100 Maximum Gain 39.5 dB Minimum Gain -10.5 dB 50 dB Differential Output Resistance ROUT Gain Range Absolute Gain Error TA = +25C, -2.0V < VG_CTL < -1.8V, VREF = 5V 0.6 TA = +25C, -1.8V < VG_CTL < +1.2V, VREF = 5V 0.5 TA = +25C, +1.2V < VG_CTL < +2.0V, VREF = 5V 1.2 VGA Gain Response Time 50dB gain change to within 1dB final value Input-Referred Noise VG_CTL set for maximum gain, no input signal VG_CTL set for +20dB of gain Output-Referred Noise Second Harmonic Third-Order Intermodulation Distortion Channel-to-Channel Crosstalk 4 HD2 IMD3 1 s 2 nV/Hz No input signal 60 VOUT = 1.5VP-P, 1kHz offset 120 VG_CLAMP_MODE = 1, VG_CTL set for +20dB of gain, fRF = 5MHz, VOUT = 1.5VP-P -55 VOUT = 1VP-P differential, fRF = 10MHz, VG_CTL set for +20dB of gain nV/Hz -62 dBc VG_CLAMP_MODE = 1, VG_CTL set for +20dB of gain, fRF = 10MHz, VOUT = 1.5VP-P VG_CTL set for +20dB of gain, fRF1 = 5MHz, fRF2 = 5.01MHz, VOUT = 1.5VP-P, VREF = 5V (Note 3) dB -62 -40 -52 dBc -80 dB _______________________________________________________________________________________ Ultrasound VGA Integrated with CW Octal Mixer (Figure 7, VCC = VREF = 4.75V to 5.25V, TA = 0C to +70C, VGND = 0V, LOW_PWR = 0, M4_EN = 0, CW_FILTER = 1, TEST_MODE = 0, PD = 0, CW_VG = 0, CW_M1 = 0, CW_M2 = 0, VG_CLAMP_MODE = 1, fRF = fLO/16 = 5MHz, capacitance to GND at each of the VGA differential outputs is 60pF, differential capacitance across the VGA outputs is 10pF, RL = 1k, CW mixer outputs pulled up to +11V through four separate 0.1% 115 resistors, differential mixer inputs are driven from a low-impedance source. Typical values are at VCC = VREF = 5V, TA = +25C, unless otherwise noted.) (Note 2) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS Maximum Output Voltage at Clamp ON VG_CLAMP_MODE = 0, VG_CTL set for +20dB of gain, 350mVP-P differential input 2.2 VP-P differential Maximum Output Voltage at Clamp OFF VG_CLAMP_MODE = 1, VG_CTL set for +20dB of gain, 350mVP-P differential input 3.4 VP-P differential CW MIXER MODE Mixer RF Frequency Range 0.9 Mixer LO Frequency Range 1 7.6 MHz 7.5 MHz Mixer IF Frequency Range 100 kHz Maximum Input Voltage Range 1.8 VP-P differential Differential Input Resistance 633 CW_FILTER = 1 1440 Mode 3, fRF = fLO/4 = 1.25MHz, measured at a 1kHz offset frequency; clutter tone at 0.9VP-P differential measured at the mixer input Input-Referred Noise Voltage Third-Order Intermodulation Distortion CW_FILTER = 0 IMD3 6 nV/Hz Mode 3, RF terminated into 50; fLO/4 = 1.25MHz, measured at 1kHz offset 4.6 Mode 1, fRF1 = 5MHz at 0.9VP-P differential input, Doppler tone fRF2 = 5.01MHz at 25dBc from clutter tone, fLO/16 = 5MHz (Note 10) -50 Mixer Output Voltage Compliance (Note 11) Channel-to-Channel Phase Matching Measured under zero beat conditions, fRF = 5MHz, fLO/16 = 5MHz (Note 12) 3 Degrees Channel-to-Channel Gain Matching Measured under zero beat conditions, fRF = 5MHz, fLO/16 = 5MHz (Note 12) 2 dB Transconductance (Note 13) 4.75 dBc CW_FILTER = 1 fRF = 1.1MHz at 1VP-P differential, fLO/16 = 1MHz CW_FILTER = 0 (low LPF cutoff frequency) fRF = 1.1MHz at 1VP-P differential, fLO/16 = 1MHz 12.00 V 2.8 mS 2.8 _______________________________________________________________________________________ 5 MAX2036 AC ELECTRICAL CHARACTERISTICS--CW MIXER MODE (continued) MAX2036 Ultrasound VGA Integrated with CW Octal Mixer AC ELECTRICAL CHARACTERISTICS--CW MIXER MODE (continued) (Figure 7, VCC = VREF = 4.75V to 5.25V, TA = 0C to +70C, VGND = 0V, LOW_PWR = 0, M4_EN = 0, CW_FILTER = 1, TEST_MODE = 0, PD = 0, CW_VG = 0, CW_M1 = 0, CW_M2 = 0, VG_CLAMP_MODE = 1, fRF = fLO/16 = 5MHz, capacitance to GND at each of the VGA differential outputs is 60pF, differential capacitance across the VGA outputs is 10pF, RL = 1k, CW mixer outputs pulled up to +11V through four separate 0.1% 115 resistors, differential mixer inputs are driven from a low-impedance source. Typical values are at VCC = VREF = 5V, TA = +25C, unless otherwise noted.) (Note 2) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS 10 MHz SERIAL SHIFT REGISTER Serial Shift Register Programming Rate Minimum Data Set-Up Time tDSU 30 ns Minimum Data Hold Time tHLD 2 ns Minimum Data Clock Time tDCLK 100 ns Minimum Data Clock Pulse Width High tDCLKPWH 30 ns Minimum Data Clock Pulse Width Low tDCLKPWL 30 ns tLD 30 ns tMIXCLK 30 ns tCLH 30 ns Minimum Load Line Minimum Load Line High to Mixer Clock On Minimum Data Clock to Load Line High Note 2: Specifications at TA = +25C and TA = +70C are guaranteed by production. Specifications at TA = 0C are guaranteed by design and characterization. Note 3: Noise performance of the device is dependent on the noise contribution from the supply to VREF. Use a low-noise supply for VREF. VCC and VREF can be connected together to share the same supply voltage if the supply for VCC exhibits low noise. Note 4: Total on-chip power dissipation is calculated as PDISS = VCC x ICC + VREF x IREF + [11V - (IMIX/4) x 115] x IMIX. Note 5: Note that the LVDS CWD LO clocks are DC-coupled. This is to ensure immediate synchronization when the clock is first turned on. An AC-coupled LO is problematic in that the RC time constant associated with the coupling capacitors and the input impedance of the pin causes there to be a period of time (related to the RC time constant) when the DC level on the chip side of the capacitor is outside the acceptable common-mode range and the LO swing does not exceed both the logic thresholds required for proper operation. This problem associated with AC-coupling would cause an inability to ensure synchronization among beamforming channels. The LVDS signal is terminated differentially with an external 100 resistor on the board. Note 6: External 100 resistor terminates the LVDS differential signal path. Note 7: The mixer common-mode current (3.25mA/channel) is specified as the common-mode current in each of the differential mixer outputs (CW_QOUT+, CW_QOUT-, CW_IOUT+, CW_IOUT-). Note 8: Specification guaranteed only for DOUT driving DIN of the next device in a daisy-chain fashion. Note 9: This response time does not include the CW output highpass filter. When switching to VGA mode, the CW outputs stop drawing current and the output voltage goes to the rail. If a highpass filter is used, the recovery time can be excessive and a switching network is recommended as shown in the Applications Information section. Note 10: See the Ultrasound-Specific IMD3 Specification in the Applications Information section. Note 11: Mixer output-voltage compliance is the range of acceptable voltages allowed on the CW mixer outputs. Note 12: Channel-to-channel gain-and-phase matching measured on 30 pieces during engineering characterization at room temperature. Each mixer is used as a phase detector and produces a DC voltage in the IQ plane. The phase is given by the angle of the vector drawn on that plane. Multiple channels from multiple parts are compared to each other to produce the phase variation. Note 13: Transconductance is defined as the quadrature summing of the CW differential output current at baseband divided by the mixer's input voltage. 6 _______________________________________________________________________________________ Ultrasound VGA Integrated with CW Octal Mixer VOUT = 1VP-P DIFFERENTIAL GAIN = 20dB -10 -20 3.5 PSMR (dBc) 3.0 2.5 2.0 IMD3 (dBc) -50 -60 -70 1.5 -30 f = 10MHz -40 -50 -60 1.0 -80 0 -90 7.5 10.0 12.5 15.0 17.5 20.0 -80 0 25 FREQUENCY (MHz) 50 75 -5 5 15 25 35 45 GAIN (dB) FREQUENCY (kHz) SECOND-HARMONIC DISTORTION vs. GAIN THIRD-HARMONIC DISTORTION vs. GAIN 0 VOUT = 1VP-P DIFFERENTIAL -10 -15 100 125 150 175 200 0 -20 MAX2036 toc05 5.0 VOUT = 1VP-P DIFFERENTIAL -10 -20 -30 -30 f = 12MHz -40 -50 HD3 (dBc) 2.5 MAX2036 toc04 0 f = 2MHz, 5MHz -70 0.5 HD2 (dBc) OVERDRIVE PHASE DELAY (ns) VOUT = 1.5VP-P DIFFERENTIAL VMOD = 50mVP-P, fCARRIER = 5MHz, GAIN = 20dB -40 0 MAX2036 toc02 VIN1 = 35mVP-P DIFFERENTIAL VIN2 = 87.5mVP-P DIFFERENTIAL GAIN = 20dB 4.0 -30 MAX2036 toc01 5.0 4.5 TWO-TONE ULTRASOUND-SPECIFIC IMD3 vs. GAIN POWER-SUPPLY MODULATION RATIO MAX2036 toc03 OVERDRIVE PHASE DELAY vs. FREQUENCY f = 5MHz -60 -70 f = 12MHz -40 f = 5MHz -50 -60 -70 -80 -90 -90 -100 -100 -15 -5 f = 2MHz -80 f = 2MHz 5 15 25 35 45 GAIN (dB) -15 -5 5 15 25 45 OVERLOAD RECOVERY TIME OVERLOAD RECOVERY TIME MAX2036 toc07 MAX2036 toc06 f = 5MHz OUTPUT OVERLOAD TO 1VP-P 35 GAIN (dB) DIFFERENTIAL INPUT 200mV/div f = 5MHz DIFFERENTIAL INPUT 200mV/div DIFFERENTIAL OUTPUT 500mV/div DIFFERENTIAL OUTPUT 500mV/div OUTPUT OVERLOAD TO 100mVP-P _______________________________________________________________________________________ 7 MAX2036 Typical Operating Characteristics (Figure 7, VCC = VREF = 4.75V to 5.25V, VGND = 0V, PD = 0, VG_CLAMP_MODE = 1, fRF = 5MHz, capacitance to GND at each of the VGA differential outputs is 60pF, differential capacitance across the VGA outputs is 10pF, RL = 1k, TA = 0C to +70C. Typical values are at VCC = VREF = 5V, VCM = 3.0V, TA = +25C, unless otherwise noted.) Typical Operating Characteristics (continued) (Figure 7, VCC = VREF = 4.75V to 5.25V, VGND = 0V, PD = 0, VG_CLAMP_MODE = 1, fRF = 5MHz, capacitance to GND at each of the VGA differential outputs is 60pF, differential capacitance across the VGA outputs is 10pF, RL = 1k, TA = 0C to +70C. Typical values are at VCC = VREF = 5V, VCM = 3.0V, TA = +25C, unless otherwise noted.) -85 -70 -80 -90 -90 -95 -100 -110 -15 -5 5 15 25 35 10 GAIN vs. DIFFERENTIAL ANALOG CONTROL VOLTAGE (VG_CTL) GAIN (dB) 15 5 -5 -15 -1.5 -0.5 0.5 1.5 30 35 25 30 25 15 20 10 15 5 1 10 100 0.1 1000 1 10 100 FREQUENCY (MHz) LARGE-SIGNAL BANDWIDTH vs. FREQUENCY LARGE-SIGNAL BANDWIDTH vs. FREQUENCY LARGE-SIGNAL BANDWIDTH vs. FREQUENCY MAX2036 toc14 20 VOUT = 1.5VP-P DIFFERENTIAL VG_CTL = +1.2VP-P DIFFERENTIAL 15 10 15 5 -5 GAIN (dB) 0 GAIN (dB) 10 10 0 -5 -15 0 -10 -20 -5 -15 -25 -20 1 10 FREQUENCY (MHz) 100 1000 1000 -10 5 -10 VOUT = 1.5VP-P DIFFERENTIAL VG_CTL = +1.7VP-P DIFFERENTIAL 5 20 0.1 MAX2036 toc10 0 0.1 FREQUENCY (MHz) VOUT = 1.5VP-P DIFFERENTIAL VG_CTL = +0.2VP-P DIFFERENTIAL 45 20 VG_CTL (VP-P DIFFERENTIAL) 30 25 35 VOUT = 1.5VP-P DIFFERENTIAL VG_CTL = -0.8VP-P DIFFERENTIAL 35 40 2.5 25 40 10 -2.5 15 LARGE-SIGNAL BANDWIDTH vs. FREQUENCY MAX2036 toc15 GAIN (dB) 25 5 LARGE-SIGNAL BANDWIDTH vs. FREQUENCY GAIN (dB) 35 -5 GAIN (dB) VOUT = 1.5VP-P DIFFERENTIAL VG_CTL = -2VP-P DIFFERENTIAL 45 -15 100 50 MAX2036 toc11 f = 5MHz 40 FREQUENCY (MHz) GAIN (dB) 45 50 30 1 45 MAX2036 toc12 -100 60 MAX2036 toc13 -80 -60 f = 5MHz 70 MAX2036 toc16 -75 80 OUTPUT-REFERRED NOISE VOLTAGE (nV/Hz) -50 CROSSTALK (dB) CROSSTALK (dB) VOUT = 1VP-P DIFFERENTIAL GAIN = 20dB, ADJACENT CHANNELS -40 -70 8 MAX2036 toc09 VOUT = 1.5VP-P DIFFERENTIAL f = 10MHz, ADJACENT CHANNELS -65 -30 MAX2036 toc08 -60 OUTPUT-REFERRED NOISE VOLTAGE vs. GAIN CHANNEL-TO-CHANNEL CROSSTALK vs. FREQUENCY CHANNEL-TO-CHANNEL CROSSTALK vs. GAIN GAIN (dB) MAX2036 Ultrasound VGA Integrated with CW Octal Mixer -30 0.1 1 10 100 FREQUENCY (MHz) 1000 0.1 1 10 100 FREQUENCY (MHz) _______________________________________________________________________________________ 1000 Ultrasound VGA Integrated with CW Octal Mixer -25 -30 -30 THIRD HARMONIC -40 -50 -60 SECOND HARMONIC -70 -80 -60 -80 -85 -90 -95 1000 0 0.5 -55 -60 THIRD HARMONIC -65 -70 -75 SECOND HARMONIC -80 -85 -90 2.5 200 3.0 25 45 65 85 800 1100 1400 1700 2000 HARMONIC DISTORTION vs. FREQUENCY TWO-TONE ULTRASOUND-SPECIFIC IMD3 vs. FREQUENCY VOUT = 1VP-P DIFFERENTIAL GAIN = 20dB -20 THIRD HARMONIC 0 VOUT = 1VP-P DIFFERENTIAL GAIN = 20dB -10 -20 -30 -40 -50 -60 SECOND HARMONIC -70 -30 -40 -50 -80 -60 0 105 10 20 30 40 -70 50 0 5 10 15 20 25 DIFFERENTIAL OUTPUT LOAD (pF) FREQUENCY (MHz) FREQUENCY (MHz) GAIN ERROR HISTOGRAM OUTPUT COMMON-MODE OFFSET VOLTAGE vs. GAIN DIFFERENTIAL OUTPUT IMPEDANCE MAGNITUDE vs. FREQUENCY 35 30 25 20 15 160 25 0 -4.50 -3.00 -1.50 0.75 2.25 3.75 -3.75 -2.25 -0.75 1.50 3.00 4.50 GAIN ERROR (dB) 140 120 -25 100 80 -75 5 180 50 -50 10 200 MAX2036 toc25 75 OFFSET VOLTAGE (mV) 40 100 ZOUT () SAMPLE SIZE = 188 UNITS fIN_ = 5MHz, GAIN = 20dB MAX2036 toc24 50 MAX2036 toc23 5 500 DIFFERENTIAL OUTPUT LOAD () -100 -100 0 2.0 -90 -95 45 1.5 IMD3 (dBc) -50 1.0 DIFFERENTIAL OUTPUT VOLTAGE (VP-P) 0 -10 HARMONIC DISTORTION (dBc) MAX2036 toc20 VOUT = 1VP-P DIFFERENTIAL f = 5MHz, GAIN = 20dB -45 SECOND HARMONIC -75 -100 10 100 FREQUENCY (MHz) MAX2036 toc19 -70 -100 1 THIRD HARMONIC -65 -40 -40 HARMONIC DISTORTION (dBc) -55 -90 HARMONIC DISTORTION vs. DIFFERENTIAL OUTPUT LOAD CAPACITANCE % OF UNITS -50 -35 0.1 VOUT = 1VP-P DIFFERENTIAL f = 5MHz, GAIN = 20dB -45 MAX2036 toc22 -20 -20 -40 HARMONIC DISTORTION (dBc) -15 f = 5MHz, GAIN = 20dB MAX2036 toc21 GAIN (dB) -10 MAX2036 toc18 -5 0 -10 HARMONIC DISTORTION (dBc) VOUT = 1VP-P DIFFERENTIAL VG_CTL = +2VP-P DIFFERENTIAL MAX2036 toc17 0 HARMONIC DISTORTION vs. DIFFERENTIAL OUTPUT LOAD RESISTANCE HARMONIC DISTORTION vs. DIFFERENTIAL OUTPUT VOLTAGE LARGE-SIGNAL BANDWIDTH vs. FREQUENCY 60 -100 -15 -5 5 15 GAIN (dB) 25 35 45 0.1 1 10 100 FREQUENCY (MHz) _______________________________________________________________________________________ 9 MAX2036 Typical Operating Characteristics (continued) (Figure 7, VCC = VREF = 4.75V to 5.25V, VGND = 0V, PD = 0, VG_CLAMP_MODE = 1, fRF = 5MHz, capacitance to GND at each of the VGA differential outputs is 60pF, differential capacitance across the VGA outputs is 10pF, RL = 1k, TA = 0C to +70C. Typical values are at VCC = VREF = 5V, VCM = 3.0V, TA = +25C, unless otherwise noted.) Typical Operating Characteristics (continued) (Figure 7, VCC = VREF = 4.75V to 5.25V, VGND = 0V, LOW_PWR = 0, M4_EN = 0, CW_FILTER = 1, TEST_MODE = 0, PD = 0, CW_VG = 0, CW_M1 = 0, CW_M2 = 0, CW mixer outputs pulled up to +11V through four separate 0.1% 115 resistors, differential mixer inputs are driven from a low impedance source.) CW FILTER RESPONSE (CW_FILTER = 1) CW FILTER RESPONSE (CW_FILTER = 0) 2 0 0 -5 LOSS (dB) -2 LOSS (dB) MAX2036 toc27 5 MAX2036 toc26 4 -4 -6 -8 -10 -15 -20 -10 -25 -12 -30 -14 0 5 10 15 5 10 15 20 FREQUENCY (MHz) FREQUENCY (MHz) CW IMD3 vs. FREQUENCY (MODE 1, VRF = 900mVP-P DIFFERENTIAL VCC = VREF) INPUT-REFERRED NOISE vs. CLUTTER VOLTAGE (MODE 4, F_CLUTTER = 1.25MHz AT 1kHz OFFSET) -48 -49 -50 -51 -52 4.75 5.00 5.25 -53 MAX2036 toc29 14 INPUT-REFERRED NOISE (nVHz) -47 12 10 8 6 4 2 -54 0 0 2 4 FRF (MHz) 10 0 20 MAX2036 toc28 -46 IMD3 (dBc) MAX2036 Ultrasound VGA Integrated with CW Octal Mixer 6 8 0 0.5 1.0 1.5 CLUTTER VOLTAGE (VP-P DIFF) ______________________________________________________________________________________ 2.0 Ultrasound VGA Integrated with CW Octal Mixer PIN NAME FUNCTION 1 CWIN2- 2 CWIN2+ CW Mixer Channel 2 Inverting Differential Input 3 VGIN3- VGA Channel 3 Inverting Differential Input 4 VGIN3+ VGA Channel 3 Noninverting Differential Input 5, 10, 19, 24, 29, 34, 58, 79, 81, 96 GND CW Mixer Channel 2 Noninverting Differential Input Ground 6 CWIN3- 7 CWIN3+ CW Mixer Channel 3 Inverting Differential Input 8 VGIN4- VGA Channel 4 Inverting Differential Input CW Mixer Channel 3 Noninverting Differential Input 9 VGIN4+ VGA Channel 4 Noninverting Differential Input 11 CWIN4- CW Mixer Channel 4 Inverting Differential Input 12 CWIN4+ CW Mixer Channel 4 Noninverting Differential Input 13 EXT_C1 External Compensation. Connect a 4.7F capacitor to ground as close as possible to the pin to bypass the internal biasing circuitry. 14 EXT_C2 External Compensation. Connect a 4.7F capacitor to ground as close as possible to the pin to bypass the internal biasing circuitry. 15 EXT_C3 External Compensation. Connect a 4.7F capacitor to ground as close as possible to the pin to bypass the internal biasing circuitry. 16, 42, 46, 54, 72, 82, 87 VCC 5V Power Supply. Connect to an external +5V power supply. Bypass each VCC supply to ground with 0.1F capacitors as close as possible to the pins. 17 VGIN5- VGA Channel 5 Inverting Differential Input 18 VGIN5+ VGA Channel 5 Noninverting Differential Input 20 CWIN5- CW Mixer Channel 5 Inverting Differential Input 21 CWIN5+ 22 VGIN6- VGA Channel 6 Inverting Differential Input 23 VGIN6+ VGA Channel 6 Noninverting Differential Input 25 CWIN6- CW Mixer Channel 6 Inverting Differential Input 26 CWIN6+ 27 VGIN7- VGA Channel 7 Inverting Differential Input 28 VGIN7+ VGA Channel 7 Noninverting Differential Input 30 CWIN7- CW Mixer Channel 7 Inverting Differential Input 31 CWIN7+ CW Mixer Channel 7 Noninverting Differential Input CW Mixer Channel 5 Noninverting Differential Input CW Mixer Channel 6 Noninverting Differential Input 32 VGIN8- VGA Channel 8 Inverting Differential Input 33 VGIN8+ VGA Channel 8 Noninverting Differential Input 35 CWIN8- CW Mixer Channel 8 Inverting Differential Input 36 CWIN8+ CW Mixer Channel 8 Noninverting Differential Input 37, 93 VREF 5V Reference Supply. Connect to a low-noise power supply. Bypass to GND with a 0.1F capacitor as close as possible to the pins. Note that noise performance of the device is dependent on the noise contribution from the supply to VREF. Use a low-noise supply for VREF. VCC and VREF can be connected together to share the same supply voltage if the supply for VCC exhibits low noise. ______________________________________________________________________________________ 11 MAX2036 Pin Description Ultrasound VGA Integrated with CW Octal Mixer MAX2036 Pin Description (continued) PIN 12 NAME FUNCTION External Resistor. Connect a 0.1% 7.5k resistor to ground as close as possible to the pin to set the bias for the internal biasing circuitry. 38 EXT_RES 39 CW_VG 40 PD Power-Down Switch. Drive PD high to set the device in power-down mode. Drive PD low for normal operation. 41 CW_FILTER CW Filter Mode Corner Frequency Select. Selects in corner frequency of the internal lowpass filter for the CW path. Set CW_FILTER to a logic-high for a corner frequency of 9.5MHz. Set CW_FILTER to a logic-low for a corner frequency of 4.5MHz. 43 M4_EN Mode 4 Enable. Set M4_EN to a logic-high to override the serial port and activate all 8 channels of the CW path. 44 LOW_PWR 45 DOUT 47 N.C. No Connect. Leave this pin unconnected (this pin is the TEST_MODE pin called out in the MAX2036 EV kit data sheet). 48 LO8 CW LO Input for Channel 8. LO clock input for modes 3 and 4. 49 VGOUT8+ 50 VGOUT8- 51 LO7 52 VGOUT7+ 53 VGOUT7- 55 LO6 56 VGOUT6+ 57 VGOUT6- 59 LO5 60 VGOUT5+ VGA Channel 5 Noninverting Differential Output 61 VGOUT5- VGA Channel 5 Inverting Differential Output 62 VG_CTL- 63 VG_CTL+ VGA Analog Gain Control Differential Input. Set the differential to -2V for maximum gain (+39.5dB) and +2V for minimum gain (-10.5dB). 64 LO_LVDS- CW LVDS LO Inverting Differential Input. LO clock inverting input for modes 1 and 2. 65 LO_LVDS+ 66 LO4 67 VGOUT4+ 68 VGOUT4- 69 LO3 70 VGOUT3+ 71 VGOUT3- 73 LO2 74 VGOUT2+ CW Mixer VGA Enable. Selects for VGA or CW mixer operation. Set CW_VG to a logic-high to enable the VGAs while the CW mixers are powered down. Set CW_VG to a logic-low to enable the CW mixers while the VGAs are powered down. Low-Power Enable. Set high to enable low-power CW mixer mode for the device. Serial Port Data Output. Data output for ease of daisy-chaining CW channels for analog beamforming programming. VGA Channel 8 Noninverting Differential Output VGA Channel 8 Inverting Differential Output CW LO Input for Channel 7. LO clock input for modes 3 and 4. VGA Channel 7 Noninverting Differential Output VGA Channel 7 Inverting Differential Output CW LO Input for Channel 6. LO clock input for modes 3 and 4. VGA Channel 6 Noninverting Differential Output VGA Channel 6 Inverting Differential Output CW LO Input for Channel 5. LO clock input for modes 3 and 4. CW LVDS LO Noninverting Differential Input. LO clock noninverting input for modes 1 and 2. CW LO Input for Channel 4. LO clock input for modes 3 and 4. VGA Channel 4 Noninverting Differential Output VGA Channel 4 Inverting Differential Output CW LO Input for Channel 3. LO clock input for modes 3 and 4. VGA Channel 3 Noninverting Differential Output VGA Channel 3 Inverting Differential Output CW LO Input for Channel 2. LO clock input for modes 3 and 4. VGA Channel 2 Noninverting Differential Output ______________________________________________________________________________________ Ultrasound VGA Integrated with CW Octal Mixer PIN NAME FUNCTION 75 VGOUT2- 76 LO1 77 VGOUT1+ 78 VGOUT1- 80 DIN Serial Port Data Input. Data input to program the serial shift registers. 83 CLK Serial Port Data Clock. Clock input for programming the serial shift registers. 84 CW_M1 CW Mode Select Input 1. Input for programming beamforming mode 1, 2, 3, or 4. See Table 1 for mode programming details. 85 CW_M2 CW Mode Select Input 2. Input for programming beamforming mode 1, 2, 3, or 4. See Table 1 for mode programming details. 86 VG_CLAMP _MODE 88 LOAD 89 CW_QOUT+ CW Mixer Noninverting Differential Quadrature Output. CW mixer output for 8 quadrature mixers combined. 90 CW_QOUT- CW Mixer Inverting Differential Quadrature Output. CW mixer output for 8 quadrature mixers combined. VGA Channel 2 Inverting Differential Output CW LO Input for Channel 1. LO clock input for modes 3 and 4. VGA Channel 1 Noninverting Differential Output VGA Channel 1 Inverting Differential Output VGA Clamp Mode Enable. Drive VG_CLAMP_MODE low to enable VGA clamp mode. VGA output is clamped at typically 2.2VP-P differential. Drive VG_CLAMP_MODE high to disable VGA clamp mode. Serial Port Load. Loads the data from the serial shift registers into the I/Q phase dividers. Pull LOAD bus from high to low, and from low to high for programming the I/Q phase dividers. 91 CW_IOUT- CW Mixer Inverting Differential In-Phase Output. CW mixer output for 8 in-phase mixers combined. 92 CW_IOUT+ CW Mixer Noninverting Differential In-Phase Output. CW mixer output for 8 in-phase mixers combined. 94 VGIN1- VGA Channel 1 Inverting Differential Input 95 VGIN1+ VGA Channel 1 Noninverting Differential Input 97 CWIN1- CW Mixer Channel 1 Inverting Differential Input 98 CWIN1+ 99 VGIN2- VGA Channel 2 Inverting Differential Input 100 VGIN2+ VGA Channel 2 Noninverting Differential Input -- EP CW Mixer Channel 1 Noninverting Differential Input Exposed Pad. Internally connected to GND. Connect EP to a large PCB ground plane to maximize thermal performance. ______________________________________________________________________________________ 13 MAX2036 Pin Description (continued) MAX2036 Ultrasound VGA Integrated with CW Octal Mixer Detailed Description The MAX2036 is an 8-channel VGA integrated with a programmable octal quadrature mixer array designed for ultrasound imaging and Doppler applications. The device is optimized for efficient power consumption, high dynamic range, and exceptionally low-noise performance. The VGA path features differential inputs, analog variable gain control, differential outputs for direct ADC drive, and a selectable output voltage clamp to avoid ADC overdrive. The integrated octal quadrature mixer array includes serial-programmable LO phase generators for CWD beamforming applications. The LO phase dividers can be programmed for 4, 8, or 16 quadrature phases. Lowpass filters are integrated at the input paths of each CW mixer. The outputs for the mixers are summed into single I/Q differential current outputs. The MAX2036 also integrates an octal quadrature mixer array and programmable LO phase generators for a complete continuous wave (CW) Doppler beamforming solution. The LO phase selection for each channel is programmed using a digital serial interface and a single high-frequency clock, or the LOs for each complex mixer pair can be directly driven using separate 4 x LO clocks. The serial interface is designed to allow multiple devices to be easily daisy chained in order to minimize program interface wiring. The LO phase dividers can be programmed to allow 4, 8, or 16 quadrature phases. The input path of each CW mixer consists of a selectable lowpass filter for optimal CWD noise performance. The outputs of the mixers are summed into single I and Q differential current outputs. The mixers and LO generators are designed to have exceptionally low noise performance of -155dBc/Hz at 1kHz offset from a 1.25MHz carrier, measured with 900mVP-P differential clutter signal. High-Level Wave Mixer and Programmable Beamformer Functional Diagram +5V +5V (LOW NOISE) VCC VREF MAX2036 VG_CTL+ VG_CTL- VG_CLAMP_MODE 50 VGIN1+ VGIN1- VGOUT1+ VGA VGOUT150 * * * * * * * * * * * * * * * * * * 50 VGIN8+ VGOUT8+ VGA VGIN8- VGOUT850 LOW_PWR PD CWIN1+ CW_IOUT+ CW_IOUT- I&Q CWIN1* * * * * * * * * * * * * * * * * * * * * * * * * * * CWIN8+ I&Q CWIN8- CW_QOUT+ CW_QOUT- Variable Gain Amplifier (VGA) The MAX2036's VGAs are optimized for high linearity, high dynamic range, and low output-noise performance, making this component ideal for ultrasound imaging applications. The VGA paths also exhibit a channel-to-channel crosstalk of -80dB at 10MHz and an absolute gain error of less than 0.5dB for minimal channel-to-channel focusing error in an ultrasound system. Each VGA path includes circuitry for adjusting analog gain, an output buffer with differential output ports (VGOUT_+, VGOUT_-) for driving ADCs, and differential input ports (VGIN_+, VGIN_-), which are ideal for directly interfacing to the MAX2034 quad LNA. See the High-Level Wave Mixer and Programmable BeamFormer Functional Diagram for details. 14 CW_VG CW_FILTER GND The VGA has an adjustable gain range from -10.5dB to +39.5dB, achieving a total dynamic range of 50dB (typ). The VGA gain can be adjusted using the differential gain-control inputs VG_CTL+ and VG_CTL-. Set the differential gain-control input voltage at +2V for minimum gain and -2V for maximum gain. The differential analog control common-mode voltage is 3V (typ). ______________________________________________________________________________________ Ultrasound VGA Integrated with CW Octal Mixer Octal Continuous Wave (CW) Mixer The MAX2036 CW mixers are designed using an active double-balanced topology. The mixers achieve high dynamic range and high-linearity performance, with exceptionally low noise, which is ideal for ultrasound CWD signal reception. The octal quadrature mixer array provides noise performance of -155dBc/Hz at 1kHz from a 1.25MHz carrier, and a two-tone, thirdorder, ultrasound-specific intermodulation product of typically -50dBc. See the Ultrasound-Specific IMD3 Specification in the Applications Information section. Power-Down The device can also be powered down with PD. Set PD to logic-high for power-down mode. In power-down mode, the device draws a total supply current of 27mA. Set PD to a logic-low for normal operation The octal array exhibits quadrature and in-phase differential current outputs (CW_QOUT+, CW_QOUT-, CW_IOUT+, CW_IOUT-) to produce the total CWD beamformed signal. The maximum differential current output is typically 3mAP-P and the mixer output-compliance voltage ranges from 4.75V to 12V. Overload Recovery The device is also optimized for quick overload recovery for operation under the large input-signal conditions that are typically found in ultrasound input buffer imaging applications. See the Typical Operating Characteristics for an illustration of the rapid recovery time from a transmit-related overload. High-Level CW Mixer and Programmable Beamformer Functional Diagram VREF VCC CWIN8 * * * CWIN2 CW_FILTER M4_EN MAX2036 * * * CW_IOUT+ CW_IOUTCW_IOUT2+ I Q * * * * * * CW_QOUT2- CW_QOUT* * * * * * CWIN1 I Q CW_QOUT+ I Q 5 DIN CHANNEL 8 I/Q DIVIDER PHASE SELECTOR 5 5-BIT SR 5-BIT SR CW_M1 CW_M2 LO2 * * * LO8 5 5-BIT SR * * * LOAD CHANNEL 2 I/Q DIVIDER PHASE SELECTOR * * * * * * LO_LVDS- CHANNEL 1 I/Q DIVIDER PHASE SELECTOR * * * LO_LVDS+ * * * * * * LO1 DOUT CLK GND LOW_PWR PD ______________________________________________________________________________________ 15 MAX2036 VGA Clamp A clamp is provided to limit the VGA output signals to avoid overdriving the ADC or to prevent ADC saturation. Set VG_CLAMP_MODE low to clamp the VGA differential outputs at 2.2VP-P. Set the VG_CLAMP_MODE high to disable the clamp. MAX2036 Ultrasound VGA Integrated with CW Octal Mixer CW Mixer Output Summation The outputs from the octal mixer array are summed internally to produce the total CWD summed beamformed signal. The octal array produces eight differential quadrature (Q) outputs and eight differential in-phase (I) outputs. All quadrature and in-phase outputs are summed into single I and Q differential current outputs (CW_QOUT+, CW_QOUT-, CW_IOUT+, CW_IOUT-). LO Phase Select The LO phase dividers can be programmed through the shift registers to allow for 4, 8, or 16 quadrature phases for a complete CW beamforming solution. the divide-by-16 circuit. The first 4 bits of the shift register are for programming the 16 phases; the fifth bit turns each channel on/off individually. For mode 1, set both CW_M1 and CW_M2 to a logic-low. See Table 2. Table 2. Mode 1 Logic Table (B4 = 0: Channel On/B4 = 1 Channel Off) MODE 1 CW_M1 = 0 CW_M2 = 0 MSB LSB SHUTDOWN PHASE (DEG) D C B A SD (B0) (B1) (B2) (B3) (B4) 0 0 0 0 0 0/1 22.5 0 0 0 1 0/1 CWD Beamforming Modes There are four separate modes of operating the CWD beamformer. See Table 1 for a summary of the different modes of operation. The mode of operation can be selected by the CW_M1 and CW_M2 logic inputs. Phase generation is controlled through the serial interface. See the Serial Interface section in the Applications Information section for details on how to program for different quadrature phases. Mode 1 For mode 1 operation, the LO_LVDS input frequency is typically 16 x fLO. As the CWD LO frequency range is 1MHz to 7.5MHz, the input frequency ranges from 16MHz to 120MHz. This high LO clock frequency requires a differential LVDS input. The 16 x fLO input is then divided by 16 to produce 16 phases. These 16 phases are generated for each of the 8 channels and programmed for the selected phase by a serial shift register. Each channel has a corresponding 5-bit shift register, which is used to program the output phase of 45 0 0 1 0 0/1 67.5 0 0 1 1 0/1 90 0 1 0 0 0/1 112.5 0 1 0 1 0/1 135 0 1 1 0 0/1 157.5 0 1 1 1 0/1 180 1 0 0 0 0/1 202.5 1 0 0 1 0/1 225 1 0 1 0 0/1 247.5 1 0 1 1 0/1 270 1 1 0 0 0/1 292.5 1 1 0 1 0/1 315 1 1 1 0 0/1 337.5 1 1 1 1 0/1 Table 1. Summary of CWD Beamforming Methods CW_M1 CW_M2 MODE LO INPUT CLOCK PHASE FREQUENCY INTERFACE RESOLUTION NO. OF CLOCK INPUTS PER CHIP PROGRAM BY SERIAL SHIFT REGISTER (SSR) NO. OF USEFUL BITS IN SSR 0 0 1 16 x LVDS 16 phases 1 Yes 4 0 0 1 2 8x LVDS 8 phases 1 Yes 3 1 MSB 1 0 3 4x 3V CMOS 4 phases 8 Yes 2 2 MSBs 3V CMOS Quadrature provided 8 No N/A N/A 1 1 4 4x N/A = Not applicable. 16 NO. OF DON'TCARE BITS IN SSR ______________________________________________________________________________________ Ultrasound VGA Integrated with CW Octal Mixer Table 3. Mode 2 Logic Table (DC = Don't Care, B4 = 0: Channel On/B4 = 1: Channel Off) Table 4. Mode 3 Logic Table (DC = Don't Care, B4 = 0: Channel On/B4 = 1: Channel Off) MODE 3 CW_M1 = 1 CW_M2 = 0 SHUTDOWN PHASE (DEG) D C B A SD (B0) (B1) (B2) (B3) (B4) 0 DC DC 0 0 0/1 90 DC DC 0 1 0/1 180 DC DC 1 0 0/1 270 DC DC 1 1 0/1 generated for each of the 8 channels and programmed for the selected phase by the serial shift register. For mode 3, 4 phases are generated, and only 2 of the 4 phase-programming bits are required where the 2phase programming MSBs are don't-care bits. For mode 3, set CW_M1 to a logic-high and set CW_M2 to a logic-low. See Table 4. 0 DC 0 0 0 0/1 45 DC 0 0 1 0/1 90 DC 0 1 0 0/1 135 DC 0 1 1 0/1 180 DC 1 0 0 0/1 225 DC 1 0 1 0/1 270 DC 1 1 0 0/1 Mode 4 The LO_LVDS input is not used in this mode. The appropriate phases are externally provided using separate 4 x fLO LO1-LO8 inputs for each channel. A 4 x fLO input is required so the device can internally generate accurate duty-cycle independent quadrature LO drives. Note that the serial shift register is not used in this mode. The CWD LO frequency range is 1MHz to 7.5MHz and the input frequency ranges from 4MHz to 30MHz. The appropriate inputs are provided at LO1 to LO8. A reset line is provided to the customer so that all the CWD channels can be synchronized. The reset line is implemented through the RESET. For mode 4, set both CW_M1 and CW_M2 to logic-high. See Table 5. 315 DC 1 1 1 0/1 Table 5. Mode 4 Logic Table MODE 2 CW_M1 = 0 CW_M2 = 1 SHUTDOWN PHASE (DEG) D C B A SD (B0) (B1) (B2) (B3) (B4) Mode 3 The LO_LVDS input is not used in this mode. Separate 4 x fLO clock inputs are provided using LO1-LO8 for each channel. The CWD LO frequency range is 1MHz to 7.5MHz, and the input frequency provides ranges from 4MHz to 30MHz. Note that the LO clock frequency can utilize 3V CMOS inputs. The 4 x fLO LO1-LO8 inputs are divided by 4 to produce 4 phases. These 4 phases are MODE 4 CW_M1 = 1 CW_M2 = 1 PHASE (DEG) Serial bus not used in mode 4 SHUTDOWN D C B A SD (B0) (B1) (B2) (B3) (B4) N/A N/A N/A N/A N/A N/A = Not applicable. ______________________________________________________________________________________ 17 MAX2036 Mode 2 The LO_LVDS input frequency is 8 x fLO (typ) for mode 2 operation. The CWD LO frequency range is 1MHz to 7.5MHz, and the input frequency ranges from 8MHz to 60MHz. This high LO clock frequency requires a differential LVDS input. The 8 x fLO input is then divided by 8 to produce 8 phases. These 8 phases are generated for each of the 8 channels and programmed for the selected phase by the serial shift register. Note that the serial shift register is common to modes 1, 2, and 3, where each channel has a corresponding 5-bit shift register, which is used to program the output phase. However, since mode 2 generates 8 phases only, 3 of the 4 phase-programming bits are used; 5 bits are still loaded per channel using the serial shift register, but the phase-programming MSB is a don't-care bit. The fifth bit in the shift register always turns each channel on/off individually. For mode 2, set CW_M1 to a logiclow and set CW_M2 to a logic-high. See Table 3. MAX2036 Ultrasound VGA Integrated with CW Octal Mixer DATA_IN CLOCK CHANNEL 1 A B C D SD CHANNEL 2 A B C D SD CHANNEL 3 A B C D SD CHANNEL 4 A B C D SD B3 B2 B1 B0 B4 B3 B2 B1 B0 B4 B3 B2 B1 B0 B4 B3 B2 B1 B0 B4 CHANNEL 5 A B C D SD CHANNEL 6 A B C D SD CHANNEL 7 A B C D SD CHANNEL 8 A B C D SD B3 B2 B1 B0 B4 B3 B2 B1 B0 B4 B3 B2 B1 B0 B4 B3 B2 B1 B0 B4 DATA_OUT Figure 1. Data Flow of Serial Shift Register Synchronization Figure 1 illustrates the serial programming of the 8 individual channels through the serial data port. Note that the serial data can be daisy chained from one part to another, allowing a single data line to be used to program multiple chips in the system. CW Lowpass Filter The MAX2036 also includes selectable lowpass filters between each CW differential input pair and corresponding mixer input. Shunt capacitors and resistors are integrated on chip for high band and low band. The parallel capacitor/resistor networks, which appear differentially across each of the CW differential inputs, are selectable through the CW_FILTER. Drive CW_FILTER high to set the corner frequency of the filter to be fC = 9.5MHz. Drive CW_FILTER low to set the corner frequency equal to fC = 4.5MHz. The CW_VG allows the filter inputs to be disconnected from input nodes (internal to chip) to prevent overloading the LNA output and to not change the VGA input common-mode voltage. VGA and CW Mixer Operation During normal operation, the MAX2036 is configured such that either the VGA path is enabled while the mixer array is powered down (VGA mode), or the quadrature mixer array is enabled while the VGA path is powered down (CW mode). During VGA mode, besides powering down the CW mixer array, the differential inputs to the lowpass filters and CW mixers also are internally disconnected from the input nodes, making the CW differential inputs (CWIN_+, CWIN_-) high impedance. The CW mode disconnects the VGA inputs internally from the input ports of the device. For VGA mode, set CW_VG to a logic-high, while for CW mode, set CW_VG to a logic-low. Power-Down and Low-Power Modes During device power-down, both the VGA and CW mixer are disabled regardless of the logic set at CW_VG. Both the VGA and CW mixer inputs are high impedance since the internal switches to the inputs are all disconnected. The total supply current of the device reduces to 27mA. Set PD to a logic-high for device power-down. A low-power mode is available to lower the required power for CWD operation. When selected, the complex mixers operate at lower quiescent currents and the total per-channel current is lowered to 53mA. Note that operation in this mode slightly reduces the dynamic performance of the device. Table 6 shows the logic function of standard operating modes. Table 6. Logic Function of Standard Operating Modes PD CW_VG INPUT INPUT LOW_PWR VGA CW MIXER INTERNAL SWITCH TO VGA INTERNAL SWITCH TO LPF AND CW 5V VCC CURRENT CONSUMPTION (mA) 11V VMIX CURRENT CONSUMPTION (mA) 0 1 1 N/A Off Off Off Off 27 1 0 N/A Off Off Off Off 27 0 0 0 0 Off On Off On 245 106 0 0 1 Off On Off On 245 53 0 1 N/A On Off On Off 204 0 N/A = Not applicable. 18 ______________________________________________________________________________________ Ultrasound VGA Integrated with CW Octal Mixer Mode Select Response Time The mode select response time is the time that the device takes to switch between CW and VGA modes. One possible approach to interfacing the CW outputs to an instrumentation amplifier used to drive an ADC is shown in Figure 2. In this implementation, there are four large-value (in the range of 470nF to 1F) capacitors between each of the CW_IOUT+, CW_IOUT-, CW_QOUT+, CW_QOUT- outputs and the circuitry they are driving. The output of the CW mixer usually drives the input of an instrumentation amplifier made up of op amps whose input impedance is set by common-mode setting resistors. 115 115 1F CW_IOUT- 50 The highpass pole in this case is at fP = 1/(2 x pi x RC) ~ 5Hz. Note that this low highpass corner frequency is required in order to filter the downconverted clutter tone, which appears at DC, but not interfere with CWD imaging at frequencies as low as 400Hz. For example, if one wanted to use CWD down to 400Hz, then a good choice for the highpass pole would be at least a decade below this (< 40Hz) as not to incur rolloff due to pole. Remember, if the highpass pole is set to 400Hz, the response is 3dB down at that corner frequency. The placement of the highpass pole at 5Hz in the above example is between the DC and 40Hz limitations just discussed. The bottom line is that any reasonably sized DC block between the output of the mixer and the instrumentation amplifier pose a significant time constant that slows the mode select switching speed. An alternative solution to the approach in Figure 2, which enables faster mode select response time, is shown in Figure 4. 31.6k 0.022F +11V 31.6k CW_IOUT+ 1F Figure 2. Typical Example of a CW Mixer's Output Circuit There are clearly both a highpass corner and a lowpass corner present in this output network. The lowpass corner is set primarily by the 115 mixer pullup resistors, the series 50 resistors, and the shunt 0.022F capacitor. This lowpass corner is used to filter a combination of LO leakage and upper sideband. The highpass corner, however, is of a larger concern due to the fact that it is dominated by the combination of a 1F DC blocking capacitor and the pair of shunt 31.6k resistors. If drawn, the simplified dominant highpass network would look like Figure 3. 1F 31.6k Figure 3. Simplified Circuit of Highpass Pole +5V Figure 4. Improved Mode Select Response Time Achieved with DC-Coupled Input to Instrumentation Amplifier In Figure 4, the outputs of the CWD mixers are DCcoupled into the inputs of the instrumentation amplifiers. Therefore, the op amps must be able to accommodate the full compliance range of the mixer outputs, which is a maximum of +11V when the mixers are disabled, down to the +5V supply of the MAX2036 when the mixers are enabled. The op amps can be powered from +11V for the high rail and +5V for the low rail, requiring a 6V op amp. ______________________________________________________________________________________ 19 MAX2036 Applications Information MAX2036 Ultrasound VGA Integrated with CW Octal Mixer Serial Interface The serial interface of the MAX2036 programs the LO for 16, 8, or 4 quadrature phases using a serial shift register implementation. Data is shifted into the device on DIN. The serial shift register clock is applied to the CLK input. The serial shift register has 5 bits per channel. The first 4 bits are for phase programming, and the fifth bit enables or disables each channel of the mixer array. Each mixer can be programmed to 1 of 16 phases; therefore, 4 bits are required for each channel for programming. The master high-frequency mixer clock is applied to differential inputs LO_LVDS+ and LO_LVDS(for modes 1 and 2) and LO_ (for modes 3 and 4). The LOAD input is provided to allow the user to load the phase counters with the programming values to generate the correct LO phases. The input signals for mixing are applied to the eight differential inputs, CWIN_+ and CWIN_-. The summed I/Q baseband differential outputs are provided on CW_IOUT+/- and CW_QOUT+/-. CW_M1 and CW_M2 are used to select one of the four possible modes of operation. See Table 1. The serial interface is designed to allow multiple devices to be easily daisy chained in order to minimize program interface wiring. DOUT is available for this daisy-chain function. Programming the Beamformer During normal CWD operation, the mixer clock at LO_ or LO_LVDS is on and the programming signals on DIN, CLK, and LOAD are off. (LOAD = high, CLK = low, and DIN = don't care, but fixed to a high or low). To start the programming sequence, turn off the mixer clock. Data is shifted into the shift register at a recommended 10MHz programming rate or 100ns minimum data clock period/time. See Figure 5 for timing details. After the shift registers are programmed, pull the LOAD bus to logic-low and then back to logic-high to load the internal counters into I/Q phase divider/selectors with the proper values. LOAD must remain low for a minimum time of tCLH. The user turns on the mixer clock to start beamforming. The clock must turn on such that it starts at the beginning of a mixer clock cycle. tDSU tHLD tCLH DIN CLK LOAD tDCLKPWH tDCLKPWL tDCLK MIXER CLOCK ON tLD tLDMIXCLK MIXER CLOCK OFF MIXER CLOCK ON MIXER CLOCK OFF MIXER CLOCK ON MIXER CLOCK OFF MIXER CLOCK ON Figure 5. Shift Register Timing Diagram 20 ______________________________________________________________________________________ Ultrasound VGA Integrated with CW Octal Mixer Ultrasound-Specific IMD3 Specification Unlike typical communications specs, the two input tones are not equal in magnitude for the ultrasoundspecific IMD3 two-tone specification. In this measurement, f1 represents reflections from tissue and f2 represents reflections from blood. The latter reflections are typically 25dB lower in magnitude, and hence the measurement is defined with one input tone 25dB lower than the other. The IMD3 product of interest (f1 - (f2 - f1)) presents itself as an undesired Doppler error signal in ultrasound applications. See Figure 6. External Compensation External compensation is required for bypassing internal biasing circuitry. Connect, as close as possible, individual 4.7F capacitors from each pin EXT_C1, EXT_C2, and EXT_C3 (pins 13, 14, 15) to ground. -25dB ULTRASOUND IMD3 External Bias Resistor An external resistor at EXT_RES is required to set the bias for the internal biasing circuitry. Connect, as close as possible, a 7.5k (0.1%) resistor from EXT_RES (pin 38) to ground. f1 - (f2 - f1) f1 f2 f2 + (f2 - f1) Analog Input and Output Coupling In typical applications, the MAX2036 is being driven from a low-noise amplifier (such as the MAX2034) and the VGA is typically driving a discrete differential antialias filter into an ADC (such as the MAX1436 octal ADC). The differential input impedance of the MAX2036 is typically 240. The differential outputs of the VGA are capable of driving a differential load capacitance to GND at each of the VGA differential outputs of 60pF, and differential capacitance across the VGA outputs is 10pF, RL = 1k. The differential outputs have a common-mode bias of approximately 3.75V. AC-couple these differential outputs if the next stage has a different common-mode input range. Figure 6. Ultrasound IMD3 Measurement Technique PCB Layout The pin configuration of the MAX2036 is optimized to facilitate a very compact physical layout of the device and its associated discrete components. A typical application for this device might incorporate several devices in close proximity to handle multiple channels of signal processing. The exposed pad (EP) of the MAX2036's TQFP-EP package provides a low thermal-resistance path to the die. It is important that the PCB on which the MAX2036 is mounted be designed to conduct heat from the EP. In addition, provide the EP with a low-inductance path to electrical ground. The EP MUST be soldered to a ground plane on the PCB, either directly or through an array of plated via holes. ______________________________________________________________________________________ 21 MAX2036 CW Mixer Output Summation The maximum differential current output is typically 3mA P-P and the mixer output compliance voltage ranges from 4.75V to 12V per mixer channel. The mixer common-mode current in each of the differential mixer outputs is typically 3.25mA. The total summed current would equal N x 3.25mA in each of the 115 load resistors (where N = number of channels). In this case, the quiescent output voltage at +VSUM and -VSUM outputs would be +11V - (N x 3.25mA x 115) = +11V - (8 x 3.25mA x 115) = 8.05V. The voltage swing at each output, with one channel driven at max output current (differential 3mA P-P ) while the other channels are not driven, would be 1.5mAP-P x 115 or 174mVP-P and the differential voltage would be 348mVP-P. The voltage compliance range is defined as the valid range for +VSUM and -VSUM in this example. +VIN 22 -V +V 100nF 100nF 100nF MAX2034 ONE CHANNEL ZIN IN CONTROL D2, D1, D0 100nF 100nF CW_FILTER CW_VG 12H CWIN_- CWIN_+ 12H VGIN_- VGIN_+ MAX2036 ONE CHANNEL VCC VG_CTL- GND LO DIVIDER VG_CTL+ CWD I/Q LO 50 50 VREF CW_QOUT+ CW_QOUT- CW_IOUT- CW_IOUT+ VGOUT_- 0.1F 0.1F VGOUT_+ 115 115 TO 10-BIT IMAGING ADC +VMIX 115 ADC CWD TO Q CHANNEL CWD Q CHANNELS IN CWD I CHANNELS IN ADC CWD 115 TO I CHANNEL +VMIX THIRD-ORDER BUTTERWORTH ANTI-ALIAS FILTER. MAX2036 Ultrasound VGA Integrated with CW Octal Mixer Figure 7. Typical per-Channel Ultrasound Imaging Application ______________________________________________________________________________________ Ultrasound VGA Integrated with CW Octal Mixer 51 VGOUT7VGOUT7+ LO7 52 53 54 VGOUT6+ LO6 VCC 55 56 57 LO5 GND VGOUT659 58 VGOUT5VGOUT5+ 61 60 VG_CTL+ VG_CTL63 62 LO_LVDS+ LO_LVDS65 64 VGOUT4+ LO4 66 67 68 69 VGOUT3VGOUT3+ LO3 VGOUT471 70 VCC 72 VGOUT2- VGOUT2+ LO2 75 74 73 TOP VIEW LO1 76 50 VGOUT8- VGOUT1+ VGOUT1- 77 49 78 48 VGOUT8+ LO8 GND DIN GND VCC 79 47 80 46 81 45 82 44 N.C. VCC DOUT LOW_PWR M4_EN VCC CW_FILTER PD CLK 83 43 CW_M1 CW_M2 VG_CLAMP_MODE 84 42 85 41 86 40 VCC LOAD CW_QOUT+ CW_QOUT- 87 39 88 38 90 36 CWIN8+ CW_IOUT- 91 35 CW_IOUT+ 92 34 VREF VGIN1VGIN1+ GND CWIN1- 93 33 CWIN8GND VGIN8+ 94 32 95 31 96 30 97 29 CWIN1+ 98 28 VGIN2VGIN2+ 99 27 VGIN8CWIN7+ CWIN7GND VGIN7+ VGIN7- 100 26 CWIN6+ MAX2036 89 VGIN6- 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 VGIN6+ GND CWIN6- 8 VGIN5+ GND CWIN5CWIN5+ 7 EXT_C3 VCC VGIN5- 6 EXT_C1 EXT_C2 5 GND CWIN4CWIN4+ 4 VGIN4+ 3 VGIN3VGIN3+ GND CWIN3CWIN3+ VGIN4- 2 CWIN2CWIN2+ 1 37 CW_VG EXT_RES VREF TQFP ______________________________________________________________________________________ 23 MAX2036 Pin Configuration MAX2036 Ultrasound VGA Integrated with CW Octal Mixer Package Information Chip Information PROCESS: Silicon Complementary Bipolar 24 For the latest package outline information and land patterns, go to www.maxim-ic.com/packages. Note that a "+", "#", or "-" in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. PACKAGE TYPE PACKAGE CODE DOCUMENT NO. 100 TQFP-EP C100E+3 21-0116 ______________________________________________________________________________________ Ultrasound VGA Integrated with CW Octal Mixer REVISION NUMBER REVISION DATE 0 1/09 Initial release 1 6/09 Corrected pin name inconsistencies DESCRIPTION PAGES CHANGED -- 1-6, 10, 12, 13, 18, 20 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 25 (c) 2009 Maxim Integrated Products Maxim is a registered trademark of Maxim Integrated Products, Inc. MAX2036 Revision History Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Maxim Integrated: MAX2036CCQ+ MAX2036CCQ+T