RBQ-12/33-D48 www.murata-ps.com Quarter-Brick 400-Watt Isolated DC-DC Converters Output (Vout, max) Current (A) Nominal Input (V) 11.85 33 48 Typical unit FEATURES PRODUCT OVERVIEW 391 Watts total output power, 11.85 VDC @ 33 A The fully isolated (2250 Vdc) RBQ-12/33-D48 module accepts a 36 to 75 Volt DC input voltage range (48 VDC nominal) and converts it to a low Vdc output. Applications include 48V-powered datacom and telecom installations, base stations, cellular dataphone repeaters, instruments and embedded systems. Wideband output ripple and noise is a low 100 mV, peak-to-peak. Regulated Intermediated Bus Architecture (RIBA) with PoL converters 96% ultra-high efficiency at full load (typical) 36 to 75 Volt DC input range (48 VDC nominal) Standard quarter-brick footprint Synchronous rectifier topology with 100 mV ripple & noise Up to +85 Celsius thermal performance (with derating) Stable no-load operation Multiple-unit parallel operation for increased current Fully isolated to 2250 VDC (BASIC) The RBQ's synchronous-rectifier topology with line regulation and fixed frequency operation means excellent efficiencies up to 96%, enabling "no heatsink" operation for most applications up to +85 Celsius (with derating airflow). "No fan" or zero airflow higher temperature applications may use the optional base plate for cold surface mounting or natural-convection heatsinks. A wealth of electronic protection features include input undervoltage lockout (UVLO) , output current limit, short circuit hiccup, and overtemperature shutdown. Available options include positive or negative logic remote On/Off control, conformal coating, various pin lengths, and the baseplate. Assembled using ISO-certified automated surfacemount techniques, the RBQ series is certified to all UL and IEC emissions, safety and flammability standards. Remote On/Off enable control Extensive protection features - SC, OC, UVLO, OT Certified to full safety, emissions and environmental standards Meets UL 60950-1, CAN/CSAC22.2 No. 609501, IEC60950-1, EN60950-1 safety approvals (2nd Edition) F1 *TPMBUJPO Barrier +Vin (1) +Vout (8) t4XJUDIJOH External DC Power Source On/Off Control (2) Open = On $MPTFE0GG 1PTJUJWF MPHJD t'JMUFST Controller and Power 5SBOTGFS Duty Cycle 3FHVMBUJPO t$VSSFOU4FOTF Reference and Error Amplifier -Vin (3) -Vout (4) Figure 1. Connection Diagram Typical topology is shown. Murata Power Solutions recommends an external fuse at F1. For full details go to www.murata-ps.com/rohs www.murata-ps.com/support MDC_RBQ-12/33-D48.A01 Page 1 of 15 RBQ-12/33-D48 Quarter-Brick 400-Watt Isolated DC-DC Converters PERFORMANCE SPECIFICATIONS SUMMARY AND ORDERING GUIDE Output Root Model RBQ-12/33-D48 Total VOUT (V, Power IOUT max) (A, max) (W, max) 11.85 33 391 Input Ripple & Noise (mVp-p) Typ. Max. 100 200 Regulation (max.) VIN Nom. Range Line (%) Load (%) (V) (V) +1/-2 Please refer to the part number structure for additional options and complete ordering part numbers. Regulation specifications describe the output voltage deviations as the line voltage or load current is varied from its nominal/midpoint value to either extreme. (Load step = 25 %). Line Regulation tested from 40V to 75V, output @nominal load. 3 48 36-75 IIN, min. IIN, full load load (mA) (A) 140 8.59 Efficiency Dimensions (baseplate) Typ. 96% (inches) (mm) 2.3 x 1.45 x 0.5 58.4 x 36.8 x 12.7 All specifications are at nominal line voltage and full load, +25 deg.C. unless otherwise noted. See detailed specifications. Output capacitors are 1F, 10uF and 470F in parallel, with a 220F input capacitor. I/O caps are necessary for our test equipment and may not be needed for your application. PART NUMBER STRUCTURE RB Q - 12 / 33 - D48 N B S H Lx - C RoHS Hazardous Materials compliance C = RoHS 6 (does not claim EU RoHS exemption 7b-lead in solder), standard Output Configuration RB = Regulated Converter Pin Length Option (Through-hole packages only) Quarter-Brick Package Isolated converter Blank = Standard pin length 0.180 inches (4.6mm) L1 = Pin length 0.110 inches (2.79mm)* L2 = Pin length 0.145 inches (3.68mm)* Maximum Output Voltage (11.85V) Conformal coating (optional) Blank = no coating, standard H = Coating added, optional* Maximum Rated Output Current in Amps Input Voltage Range D48 = 36-75V, 48V nominal Load Share Option Blank = no share S = Load share *Special quantity order is required; no sample quantities available. Baseplate B = Baseplate installed, standard On/Off Control Logic Option N = Negative logic P = Positive logic Note: Some model number combinations may not be available. Please contact Murata Power Solutions for ordering assistance. www.murata-ps.com/support MDC_RBQ-12/33-D48.A01 Page 2 of 15 RBQ-12/33-D48 Quarter-Brick 400-Watt Isolated DC-DC Converters FUNCTIONAL SPECIFICATIONS Conditions Minimum Full power operation Operating or non-operating, 100 mS max. duration Input to output, 100 mS to IEC/EN/UL 60950-1 Power on or off, referred to -Vin 0 ABSOLUTE MAXIMUM RATINGS Input Voltage, Continuous Input Voltage, Transient Isolation Voltage On/Off Remote Control Output Power Typical/Nominal Maximum Units 80 Vdc 0 100 Vdc 0 0 2250 15 391 Vdc Vdc W Current-limited, no damage, short-circuit 0 33 A protected Storage Temperature Range Vin = Zero (no power) -55 125 C Absolute maximums are stress ratings. Exposure of devices to greater than any of these conditions may adversely affect long-term reliability. Proper operation under conditions other than those listed in the Performance/Functional Specifications Table is not implied or recommended. Output Current INPUT Operating voltage range Recommended External Fuse Start-up threshold Undervoltage shutdown Internal Filter Type Input current Full Load Conditions Low Line Inrush Transient Output in Short Circuit No Load Input Current (Iout @ min) Shut-Down Mode Input Current Reflected (back) ripple current 36 Fast blow Rising input voltage Falling input voltage 32 30 Vin = minimum Iout = minimum, unit=ON 48 20 33.5 31.5 Pi 75 35 33 Vdc A Vdc Vdc 8.59 10.8 8.68 12 0.3 0.5 200 10 200 A A A2-Sec. A mA mA mA, RMS 140 5 70 Measured at input with specified filter GENERAL and SAFETY Efficiency Isolation Isolation Voltage, input to output Isolation Voltage, input to output Isolation Voltage, input to baseplate Isolation Voltage, output to baseplate Insulation Safety Rating Isolation Resistance Isolation Capacitance Safety Calculated MTBF Vin=48V, full load Vin=75V, full load 95 93 No baseplate With baseplate With baseplate With baseplate 2250 2250 1500 1500 96 94 % % Vdc Vdc Vdc Vdc basic 10 1500 Certifi ed to UL-60950-1, CSA-C22.2 No.609501, IEC/EN60950-1, 2nd edition Per Telcordia SR332, issue 1, class 3, ground fixed, Tambient=+25C Mohm pF Yes Hours x 106 1.8 DYNAMIC CHARACTERISTICS Fixed Switching Frequency Startup Delay Startup Delay Dynamic Load Response Dynamic Load Peak Deviation 360 Power On to Vout regulated, 10-90% Vout, resistive load Remote ON to 10% of Vout 50-75-50% load step, settling time to within 2% of Vout Same as above KHz 20 mS 10 mS 350 Sec 400 mV 1 0.8 15 2 V V mA 1 15 1 2 V V mA FEATURES and OPTIONS Remote On/Off Control "N" suffix: Negative Logic, ON state Negative Logic, OFF state Control Current "P" suffix: Positive Logic, ON state Positive Logic, OFF state Control Current ON = Pin grounded or external voltage OFF = Pin open or external voltage Open collector/drain -0.1 3.5 ON = Pin open or external voltage OFF = Ground pin or external voltage Open collector/drain 2.5 0 www.murata-ps.com/support MDC_RBQ-12/33-D48.A01 Page 3 of 15 RBQ-12/33-D48 Quarter-Brick 400-Watt Isolated DC-DC Converters FUNCTIONAL SPECIFICATIONS (CONT.) Conditions Minimum Typical/Nominal Maximum Units See Derating 0 386 391 W Measured @ 48Vin, Half Load. Over sample load (0-33A), input line (40-75V) and temperature (see derating curves) , for regular model and S option 11.5 11.7 11.85 Vdc 11 12.5 V 12.9 13.1 V For S option only 11.7 12.5 Vdc For S option only 11.69 11.71 Vdc For S option only 11.5 11.7 Vdc For S option only Output Voltage clamped (see technical note) 11.5 11.7 N/A 12.5 Vdc V 0 33 No minimum load 46 33 A 50 A 6 A +1/-2 3 200 0.02 % % mV pk-pk % of Vnom./C 6000 F OUTPUT Total Output Power Voltage Nominal Output Voltage Total Output Range Vout Overshoot Voltage Output Voltage (initial output set point @48V, no load) Output Voltage (initial output set point @48V, 50% load) Output Voltage (initial output set point @48V, 100% load) Output Voltage Overvoltage Protection Current Output Current Range Minimum Load Current Limit Inception Short Circuit Short Circuit Current 98% of Vnom., after warmup 40 Hiccup technique, autorecovery within 1.25% of Vout Short Circuit Duration (remove short for recovery) Short circuit protection method Regulation Line Regulation Load Regulation Ripple and Noise Temperature Coefficient Maximum Capacitive Loading (10% ceramic, 90% Oscon) Output shorted to ground, no damage Continuous Current limiting Vin=40 to 75V Iout=min. to max., Vin=48V 5 Hz- 20 MHz BW At all outputs Cap. ESR=<0.02, Full resistive load 100 0.003 470 MECHANICAL (Through Hole Models) Outline Dimensions (with baseplate) 2.3 x 1.45 x 0.5 58.4 x 36.8 x 12.7 2.4 69 0.04 0.001 1.0160.025 0.060 0.001 1.5240.025 Copper alloy 100-299 3.9-20 Weight (with baseplate) Through Hole Pin Diameter Input pins Through Hole Pin Diameter Output pins Through Hole Pin Material TH Pin Plating Metal and Thickness Nickel subplate Gold overplate Inches mm Ounces Grams Inches mm Inches mm -inches -inches ENVIRONMENTAL Operating Ambient Temperature Range Storage Temperature Thermal Protection/Shutdown With derating, full power, no condensation, components +125C. max. Vin = Zero (no power) Measured at hotspot Operating baseplate temperature Electromagnetic Interference Conducted, EN55022/CISPR22 Relative humidity, non-condensing Altitude -55 115 -40 External filter is required To +85C must derate -1%/1000 feet RoHS rating Notes -40 Unless otherwise noted, all specifications are at nominal input voltage, nominal output voltage and full load. General conditions are +25 Celsius ambient temperature, near sea level altitude, natural convection airflow. All models are tested and specified with external parallel 1F, 10F and 470 F output capacitors and 220 F external input capacitor. All capacitors are low-ESR types wired close to the converter. These capacitors are necessary for our test equipment and may not be needed in the user's application. 125 110 85 C 125 130 120 C C C B 10 -500 -152 Class 90 10,000 3048 %RH feet meters RoHS-6 Input (back) ripple current is tested and specified over 5 Hz to 20 MHz bandwidth. Input filtering is Cbus = 220 F, Cin = 220 F and Lbus = 4.7 H. All models are stable and regulate to specification under no load. The Remote On/Off Control is referred to -Vin. Regulation specifications describe the output voltage changes as the line voltage or load current is varied from its nominal or midpoint value to either extreme. www.murata-ps.com/support MDC_RBQ-12/33-D48.A01 Page 4 of 15 RBQ-12/33-D48 Quarter-Brick 400-Watt Isolated DC-DC Converters PERFORMANCE DATA VIN = 36V VIN = 48V VIN = 75V Dissipation at 48V input 3 6 9 12 15 18 21 Load Curre nt (Amps) 24 27 30 26 24 22 20 18 16 14 12 10 8 6 4 2 0 33 40 35 Current Share Load (Amps) 98 96 94 92 90 88 86 84 82 80 78 76 74 72 Current Sharing* Ta=25C, Vin=48V Loss E ficiency (%) Ef Efficiency and Power Dissipation 30 25 20 15 No. 1 Load No. 2 Load 10 5 0 0 6 12 18 24 30 36 42 Total Output Load (Amps) 48 54 60 66 *See Technical note section Startup Delay (Vin = 48V, Iout = 33A, Vout = nom, Cload = 470F, Ta = +25C) Ch1 = Vin, Ch2 = Vout Enable Startup Delay (Vin = 48V, Iout = 33A, Vout = nom, Cload = 470F, Ta = +25C) Ch2 = Vout, Ch4 = Enable Output ripple and Noise (Vin = 48V, Iout = 0A, Vout = nom, Cload = 1F || 10F || 470F, Ta = +25C) Output ripple and Noise (Vin = 48V, Iout = 33A, Vout = nom, Cload = 1F || 10F || 470F, Ta = +25C) www.murata-ps.com/support MDC_RBQ-12/33-D48.A01 Page 5 of 15 RBQ-12/33-D48 Quarter-Brick 400-Watt Isolated DC-DC Converters PERFORMANCE DATA Step Load Transient Response (Vin = 48V, Iout = 50-75% of Imax, Cload = 470F, Slew rate: 1A/uS, Ta = +25 C.) (-Delta = 278mV, Recovery Time = 164uS) Step Load Transient Response (Vin = 48V, Iout = 75-50% of Imax, Cload = 470F, Slew rate: 1A/uS, Ta = +25 C.) (-Delta = 266mV, Recovery Time = 156uS) Step Load Transient Response (Vin = 48V, Iout = 50-75-50% of Imax, Cload = 470F, Slew rate: 1A/uS, Ta = +25 C.) www.murata-ps.com/support MDC_RBQ-12/33-D48.A01 Page 6 of 15 RBQ-12/33-D48 Quarter-Brick 400-Watt Isolated DC-DC Converters PERFORMANCE DATA Maximum Current Temperature Derating in Longitudinal Direction Vin= 40V (air flow is from Vin to Vout), with baseplate Maximum Current Temperature Derating in Transverse Direction Vin= 40V (air flow is from -Vin to +Vin), with baseplate 40 35 35 30 0.5 m/s (100LFM) 1.0 m/s (200LFM) 1.5 m/s (300LFM) 2.0 m/s (400LFM) 2.5 m/s (500LFM) 3.0 m/s (600LFM) 25 Output Current (Amps) Output Current (Amps) 30 0.5 m/s (100LFM) 1.0 m/s (200LFM) 1.5 m/s (300LFM) 2.0 m/s (400LFM) 2.5 m/s (500LFM) 3.0 m/s (600LFM) 25 20 15 20 15 10 10 5 5 0 0 30 35 40 45 50 55 60 65 70 75 80 30 85 35 40 45 Maximum Current Temperature Derating in Transverse Direction Vin= 48V (air flow is from -Vin to +Vin), with baseplate 35 35 30 20 15 10 20 70 75 80 85 15 10 0 30 35 40 45 50 55 60 65 70 75 80 30 85 35 40 45 50 55 60 65 70 75 80 85 Ambient Temperature (C) Ambient Temperature (C) Maximum Current Temperature Derating in Transverse Direction Vin= 75V (air flow is from -Vin to +Vin), with baseplate Maximum Current Temperature Derating in Longitudinal Direction Vin= 75V (air flow is from Vin to Vout), with baseplate 40 35 35 30 30 25 Output Current (Amps) Output Current (Amps) 65 5 5 25 0.5 m/s (100LFM) 1.0 m/s (200LFM) 1.5 m/s (300LFM) 2.0 m/s (400LFM) 2.5 m/s (500LFM) 3.0 m/s (600LFM) 20 15 10 0.5 m/s (100LFM) 1.0 m/s (200LFM) 1.5 m/s (300LFM) 2.0 m/s (400LFM) 2.5 m/s (500LFM) 3.0 m/s (600LFM) 20 15 10 5 5 0 60 0.5 m/s (100LFM) 1.0 m/s (200LFM) 1.5 m/s (300LFM) 2.0 m/s (400LFM) 2.5 m/s (500LFM) 3.0 m/s (600LFM) 25 0.5 m/s (100LFM) 1.0 m/s (200LFM) 1.5 m/s (300LFM) 2.0 m/s (400LFM) 2.5 m/s (500LFM) 3.0 m/s (600LFM) Output Current (Amps) Output Current (Amps) 30 25 55 Maximum Current Temperature Derating in Longitudinal Direction Vin= 48V (air flow is from Vin to Vout), with baseplate 40 0 50 Ambient Temperature (C) Ambient Temperature (C) 0 30 35 40 45 50 55 60 65 Ambient Temperature (C) 70 75 80 85 30 35 40 45 50 55 60 65 70 75 80 85 Ambient Temperature (C) www.murata-ps.com/support MDC_RBQ-12/33-D48.A01 Page 7 of 15 RBQ-12/33-D48 Quarter-Brick 400-Watt Isolated DC-DC Converters MECHANICAL SPECIFICATIONS (THROUGH-HOLE MOUNT) BASEPLATE OPTION TOP VIEW 1.030 (26.16) 1.45 (36.8) 2.30 (58.42) 1.860 (47.24) 0.50 (12.7) 0.220 (5.59) 0.210 (5.33) M3 TYP 3PL L SEE NOTE 6 0.010 minimum clearance between standoffs and highest component 2.000 (50.8) PINS 1-3: 0.0400.002(1.0160.05) PINS 4,5: 0.0620.002(1.5750.05) 3 0.600 (15.24) 0.600 (15.24) SIDE VIEW 4 2 1 8 BASEPLATE OPTION BOTTOM VIEW NOTES: UNLESS OTHERWISE SPECIFIED: 1:M3 SCREW USED TO BOLT UNIT'S BASEPLATE TO OTHER SURFACES(SUCH AS HEATSINK) MUST NOT EXCEED 0.098''(2.5mm) DEPTH BELOW THE SURFACE OF BASEPLATE 2:APPLIED TORQUE PER SCREW SHOULD NOT EXCEED 5.3In-lb(0.6Nm); 3:ALL DIMENSION ARE IN INCHES[MILIMETER]; 4:ALL TOLERANCES: x.xxin, 0.02in(x.xmm,0.5mm) x.xxxin ,0.01in(x.xxmm,0.25mm) 5:COMPONENT WILL VARY BETWEEN MODELS 6:STANDARD PIN LENGTH: 0.180 Inch FOR L2 PIN LENGTH OPTION IN MODEL NAME, SEE PART NUMBER STRUCTURE. Dimensions are in inches (mm shown for ref. only). INPUT/OUTPUT CONNECTIONS Pin Function 1 +Vin 2 Remote On/Off 3 -Vin 4 -Vout 8 +Vout The 0.145" (L2) pin length is shown. Please refer to the part number structure for alternate pin lengths. Third Angle Projection Tolerances (unless otherwise specified): .XX 0.02 (0.5) .XXX 0.010 (0.25) Angles 2 Components are shown for reference only and may vary between units. www.murata-ps.com/support MDC_RBQ-12/33-D48.A01 Page 8 of 15 RBQ-12/33-D48 Quarter-Brick 400-Watt Isolated DC-DC Converters SHIPPING TRAYS AND BOXES, THROUGH-HOLE MOUNT 9.92 REF 9.92 REF EACH STATIC DISSIPATIVE POLYETHYLENE FOAM TRAY ACCOMMODATES 15 CONVERTERS IN A 3 X 5 ARRAY 0.88 REF 2.750.25 CLOSED HEIGHT CARTON ACCOMMODATES TWO (2) TRAYS YIELDING 30 CONVERTERS PER CARTON MPQ=30 11.00.25 10.50.25 SHIPPING TRAY DIMENSIONS RBQ modules are supplied in a 15-piece (5 x 3) shipping tray. The tray is an anti-static closed-cell polyethylene foam. Dimensions are shown below. 252.0 +.000 [9.92] -.062 46.36 [1.825] TYP 252.0 +.000 [9.92] -.062 15.875 [0.625] TYP 60.96 [2.400] TYP 18.67 [0.735] 36.83 [1.450] TYP CL 18.42 [0.725] TYP 6.35 [.25] R TYP 6.35 [.25] CHAMFER TYP (4-PL) Notes: 1. Material: Dow 220 antistat ethafoam (Density: 34-35 kg/m3) 2. Dimensions: 252 x 252 x 19.1 mm 5 x 3 array (15 per tray) 3. All dimensions in millimeters [inches] 4. Tolerances unless otherwise specified: +1/-0 www.murata-ps.com/support MDC_RBQ-12/33-D48.A01 Page 9 of 15 RBQ-12/33-D48 Quarter-Brick 400-Watt Isolated DC-DC Converters TECHNICAL NOTES Thermal Shutdown Extended operation at excessive temperature will initiate overtemperature shutdown triggered by a temperature sensor inside the PWM controller. This operates similarly to overcurrent and short circuit mode. The inception point of the overtemperature condition depends on the average power delivered, the ambient temperature and the extent of forced cooling airflow. Thermal shutdown uses only the hiccup mode (autorestart). Parallel Load Sharing (S Option, Load Sharing) Two or more converters may be connected in parallel at both the input and output terminals to support higher output current (total power, see figure 2) or to improve reliability due to the reduced stress that results when the modules are operating below their rated limits. For applications requiring current share, follow the guidelines below. See specification table for Output Voltage set points. The stated output voltage set point is trimmed to a very narrow range (11.7V 10mV @48Vin, 50% load). The output voltage will decrease when the load current is increased. Our goal is to have each converter contribute nearly identical current into the output load under all input, environmental and load conditions. F1 +Vin +Vout Vin CH1 On/Off CH2 Vout CH3 CH1 = Vin CH2 = On/Off CH3 = Vout Figure 3. Typical Turn On for Positive Logic Modules CAUTION: This converter is not internally fused. To avoid danger to persons or equipment and to retain safety certification, the user must connect an external fast-blow input fuse as listed in the specifications. Be sure that the PC board pad area and etch size are adequate to provide enough current so that the fuse will blow with an overload. On/Off -Vin -Vout + + Input Source - + Input Filter - On/Off Signal F2 +Vin +Vout On/Off -Vin LOAD -Vout - F3 +Vin +Vout On/Off -Vin -Vout Figure 2. Load Sharing Block Diagram Using Parallel Connections - Load Sharing (Power Boost) All converters must be powered up and powered down simultaneously. Use a common input power source. It is required to use a common Remote On/Off logic control signal to turn on modules (see figure 2). When Vin has reached steady state, apply control signal to the all modules. Figure 3 illustrates the turn on process for positive logic modules. First power up the parallel system (all converters) with a load not exceeding the rated load of each converter and allow converters to settle (typically 20-100mS) before applying full load. As a practical matter, if the loads are downstream PoL converters, power these up shortly after the converter has reached steady state output. Also be aware of the delay caused by charging up external bypass capacitors. It is critical that the PCB layout incorporates identical connections from each module to the load; use the same trace rating and airflow/thermal environments. If you add input filter components, use identical components and layout. When converters are connected in parallel, allow for a safety factor of at least 10%. Up to 90% of max output current can be used from each module. Using Parallel Connections - Redundancy (N+1) The redundancy connections in figure 4 requires external user supplied "OR"ing diodes or "OR"ing MOSFETs for reliability purposes. The diodes allow for an uninterruptable power system operation in case of a catastrophic failure (shorted output) by one of the converters. The diodes should be identical part numbers to enhance balance between the converters. The default factory nominal voltage should be sufficiently matched between converters. The OR'ing diode system is the responsibility of the user. Be aware of the power levels applied to the diodes and possible heat sink requirements. Schottky power diodes with approximately 0.3V drops or "OR"ing MOSFETs may be suitable in the loop whereas 0.7 V silicon power diodes may not be advisable. In the event of an internal device fault or failure of the mains power F1 +Vin +Vout On/Off -Vin -Vout + + Input Source - + Input Filter - On/Off Signal F2 +Vin +Vout On/Off -Vin LOAD -Vout - F3 +Vin +Vout On/Off -Vin -Vout Figure 4. Redundant Parallel Connections www.murata-ps.com/support MDC_RBQ-12/33-D48.A01 Page 10 of 15 RBQ-12/33-D48 Quarter-Brick 400-Watt Isolated DC-DC Converters modules on the primary side, the other devices automatically take over the entire supply of the loads. In the basic N+1 power system, the "N" equals the number of modules required to fully power the system and "+1" equals one back-up module that will take over for a failed module. If the system consists of two power modules, each providing 50% of the total load power under normal operation and one module fails, another one delivers full power to the load. This means you can use smaller and less expensive power converters as the redundant elements, while achieving the goal of increased availability. Start Up Considerations When power is first applied to the DC-DC converter, there is some risk of start up difficulties if you do not have both low AC and DC impedance and adequate regulation of the input source. Make sure that your source supply does not allow the instantaneous input voltage to go below the minimum voltage at all times. Use a moderate size capacitor very close to the input terminals. You may need two or more parallel capacitors. A larger electrolytic or ceramic cap supplies the surge current and a smaller parallel low-ESR ceramic cap gives low AC impedance. Remember that the input current is carried both by the wiring and the ground plane return. Make sure the ground plane uses adequate thickness copper. Run additional bus wire if necessary. Input Fusing Certain applications and/or safety agencies may require fuses at the inputs of power conversion components. Fuses should also be used when there is the possibility of sustained input voltage reversal which is not current-limited. For greatest safety, we recommend a fast blow fuse installed in the ungrounded input supply line. Input Under-Voltage Shutdown and Start-Up Threshold Under normal start-up conditions, converters will not begin to regulate properly until the rising input voltage exceeds and remains at the Start-Up Threshold Voltage (see Specifications). Once operating, converters will not turn off until the input voltage drops below the Under-Voltage Shutdown Limit. Subsequent restart will not occur until the input voltage rises again above the Start-Up Threshold. This built-in hysteresis prevents any unstable on/off operation at a single input voltage. Start-Up Time Assuming that the output current is set at the rated maximum, the Vin to Vout Start-Up Time (see Specifications) is the time interval between the point when the rising input voltage crosses the Start-Up Threshold and the fully loaded output voltage enters and remains within its specified accuracy band. Actual measured times will vary with input source impedance, external input capacitance, input voltage slew rate and final value of the input voltage as it appears at the converter. These converters include a soft start circuit to moderate the duty cycle of its PWM controller at power up, thereby limiting the input inrush current. The On/Off Remote Control interval from On command to Vout (final 5%) assumes that the converter already has its input voltage stabilized above the Start-Up Threshold before the On command. The interval is measured from the On command until the output enters and remains within its specified accuracy band. The specification assumes that the output is fully loaded at maximum rated current. Similar conditions apply to the On to Vout regulated specification such as external load capacitance and soft start circuitry. Recommended Input Filtering The user must assure that the input source has low AC impedance to provide dynamic stability and that the input supply has little or no inductive content, including long distributed wiring to a remote power supply. The converter will operate with no additional external capacitance if these conditions are met. For best performance, we recommend installing a low-ESR capacitor immediately adjacent to the converter's input terminals. The capacitor should be a ceramic type such as the Murata GRM32 series or a polymer type. Make sure that the input terminals do not go below the undervoltage shutdown voltage at all times. More input bulk capacitance may be added in parallel (either electrolytic or tantalum) if needed. Recommended Output Filtering The converter will achieve its rated output ripple and noise with no additional external capacitor. However, the user may install more external output capacitance to reduce the ripple even further or for improved dynamic response. Again, use low-ESR ceramic (Murata GRM32 series) or polymer capacitors. Mount these close to the converter. Measure the output ripple under your load conditions. Use only as much capacitance as required to achieve your ripple and noise objectives. Excessive capacitance can make step load recovery sluggish or possibly introduce instability. Do not exceed the maximum rated output capacitance listed in the specifications. Input Ripple Current and Output Noise All models in this converter series are tested and specified for input reflected ripple current and output noise using designated external input/output components, circuits and layout as shown in the figures below. The Cbus and Lbus components simulate a typical DC voltage bus. TO OSCILLOSCOPE CURRENT PROBE +Vin VIN + - + - LBUS CBUS CIN -Vin CIN = 220F (100V), ESR < 700m @ 100kHz CBUS = 220F (100V), ESR < 100m @ 100kHz LBUS = 4.7H Figure 5. Measuring Input Ripple Current Minimum Output Loading Requirements All models regulate within specification and are stable under no load to full load conditions. Operation under no load might however slightly increase output ripple and noise. www.murata-ps.com/support MDC_RBQ-12/33-D48.A01 Page 11 of 15 RBQ-12/33-D48 Quarter-Brick 400-Watt Isolated DC-DC Converters protection. In the extremely unlikely event of output circuit failure, excessive voltage could be applied to your circuit. Consider using an appropriate fuse in series with the output. +VOUT C1 C2 C3 SCOPE RLOAD -VOUT C1 = 1F C2 = 10F C3 = 470F Figure 6. Measuring Output Ripple and Noise (PARD) Thermal Shutdown To prevent many over temperature problems and damage, these converters include thermal shutdown circuitry. If environmental conditions cause the temperature of the DC-DCs to rise above the Operating Temperature Range up to the shutdown temperature, an on-board electronic temperature sensor will power down the unit. When the temperature decreases below the turn-on threshold, the converter will automatically restart. There is a small amount of hysteresis to prevent rapid on/off cycling. CAUTION: If you operate too close to the thermal limits, the converter may shut down suddenly without warning. Be sure to thoroughly test your application to avoid unplanned thermal shutdown. Temperature Derating Curves The graphs in this data sheet illustrate typical operation under a variety of conditions. The Derating curves show the maximum continuous ambient air temperature and decreasing maximum output current which is acceptable under increasing forced airflow measured in Linear Feet per Minute ("LFM"). Note that these are AVERAGE measurements. The converter will accept brief increases in current or reduced airflow as long as the average is not exceeded. Note that the temperatures are of the ambient airflow, not the converter itself which is obviously running at higher temperature than the outside air. Also note that "natural convection" is defined as very flow rates which are not using fan-forced airflow. Depending on the application, "natural convection" is usually about 30-65 LFM but is not equal to still air (0 LFM). Murata Power Solutions makes Characterization measurements in a closed cycle wind tunnel with calibrated airflow. We use both thermocouples and an infrared camera system to observe thermal performance. As a practical matter, it is quite difficult to insert an anemometer to precisely measure airflow in most applications. Sometimes it is possible to estimate the effective airflow if you thoroughly understand the enclosure geometry, entry/exit orifice areas and the fan flowrate specifications. CAUTION: If you exceed these Derating guidelines, the converter may have an unplanned Over Temperature shut down. Also, these graphs are all collected near Sea Level altitude. Be sure to reduce the derating for higher altitude. Output Current Limiting Current limiting inception is defined as the point at which full power falls below the rated tolerance. See the Performance/Functional Specifications. Note particularly that the output current may briefly rise above its rated value in normal operation as long as the average output power is not exceeded. This enhances reliability and continued operation of your application. If the output current is too high, the converter will enter the short circuit condition. Output Short Circuit Condition When a converter is in current-limit mode, the output voltage will drop as the output current demand increases. If the output voltage drops too low (approximately 97% of nominal output voltage for most models), the PWM controller will shut down. Following a time-out period, the PWM will restart, causing the output voltage to begin rising to its appropriate value. If the short-circuit condition persists, another shutdown cycle will initiate. This rapid on/off cycling is called "hiccup mode." The hiccup cycling reduces the average output current, thereby preventing excessive internal temperatures and/or component damage. A short circuit can be tolerated indefinitely. The "hiccup" system differs from older latching short circuit systems because you do not have to power down the converter to make it restart. The system will automatically restore operation as soon as the short circuit condition is removed. Remote On/Off Control On the input side, a remote On/Off Control can be specified with either logic type. Please refer to the Connection Diagram on page 1 for On/Off connections. Positive-logic models are enabled when the On/Off pin is left open or is pulled high to +15V with respect to -VIN. Positive-logic devices are disabled when the On/Off is grounded or brought to within a low voltage (see Specifications) with respect to -VIN. Negative-logic models are on (enabled) when the On/Off is grounded or brought to within a low voltage (see Specifications) with respect to -VIN. The device is off (disabled) when the On/Off is left open or is pulled high to +15VDC Max. with respect to -VIN. Dynamic control of the On/Off function should be able to sink specified signal current when brought low and withstand specified voltage when brought high. Be aware too that there is a finite time in milliseconds (see Specifications) between the time of On/Off Control activation and stable output. This time will vary slightly with output load type and current and input conditions. Output Capacitive Load These converters do not require external capacitance added to achieve rated specifications. Users should only consider adding capacitance to reduce switching noise and/or to handle spike current load steps. Install only enough capacitance to achieve noise objectives. Excess external capacitance may cause degraded transient response and possible oscillation or instability. Output Fusing The converter is extensively protected against current, voltage and temperature extremes. However your output application circuit may need additional www.murata-ps.com/support MDC_RBQ-12/33-D48.A01 Page 12 of 15 RBQ-12/33-D48 Quarter-Brick 400-Watt Isolated DC-DC Converters Output OVP (Output Clamped) The RBQ-12/33-D48 module incorporates circuitry to protect the output/load (Output OVP, Over Voltage Protection) by effectively clamping the output voltage to a maximum of 13.1V under certain fault conditions. The initial output voltage is set at the factory for an accuracy of 1.5%, and is regulated over line load and temperature using a closed loop feedback system. In the event of a failure that causes the module to operate open loop (failure in the control loop), the output voltage will be determined by the input voltage/duty cycle of the voltage conversion (Pulse Width Modulation) circuit. For example, when the input voltage is at 36V, the duty cycle is D1; when the input voltage is at 75V, the maximum duty cycle is D1/2; this change in duty cycle compensates Vout for Vin changes. As Vin continues to increase above 75V the voltage at Vout is clamped because maximum duty cycle has been reached. The output voltage is always proportional to Vin*Duty in a buck derived topology. Figure 4 is the test waveform for the RBQ-12/33-D48 module when its feedback loop is open, simulating a loop failure. Channel 1 is the input voltage and Channel 2 it the output voltage. When the input voltage climbs from 48Vdc to 100Vdc, the output voltage remains stable. Figure 7. Test Waveform with Feedback Loop Open www.murata-ps.com/support MDC_RBQ-12/33-D48.A01 Page 13 of 15 RBQ-12/33-D48 Quarter-Brick 400-Watt Isolated DC-DC Converters Emissions Performance, Model RBQ-12-33-D48 Murata Power Solutions measures its products for radio frequency emissions against the EN 55022 and CISPR 22 standards. Passive resistance loads are employed and the output is set to the maximum voltage. If you set up your own emissions testing, make sure the output load is rated at continuous power while doing the tests. [3] Conducted Emissions Test Results The recommended external input and output capacitors (if required) are included. Please refer to the fundamental switching frequency. All of this information is listed in the Product Specifications. An external discrete filter is installed and the circuit diagram is shown below. VCC RTN C1 C2 C3 L1 L2 C4 C5 + C6 C7 + C12 DC/DC LOAD -48V C8 C9 C10 GND C11 GND Figure 8. Conducted Emissions Test Circuit Graph 1. Conducted emissions performance, Positive Line, CISPR 22, Class B, full load [1] Conducted Emissions Parts List Reference C1, C2, C3, C4, C5 C6 L1, L2 C8, C9, C10, C11 C7 C12 Part Number Description Vendor SMD CERAMIC-100VGRM32ER72A105KA01L Murata 1000nF-X7R-1210 SMD CERAMIC100V-100nFGRM319R72A104KA01D Murata 10%-X7R-1206 COMMON MODE-473uHPG0060T Pulse 25%-14A SMD CERAMIC630V-0.22uFGRM55DR72J224KW01L Murata 10%-X7R-2220 Aluminum100V-220UfUHE2A221MHD Nichicon 10%-long lead NA [2] Conducted Emissions Test Equipment Used Hewlett Packard HP8594L Spectrum Analyzer - S/N 3827A00153 2Line V-networks LS1-15V 50/50Uh Line Impedance Stabilization Network Graph 2. Conducted emissions performance, Negative Line, CISPR 22, Class B, full load [4] Layout Recommendations Most applications can use the filtering which is already installed inside the converter or with the addition of the recommended external capacitors. For greater emissions suppression, consider additional filter components and/or shielding. Emissions performance will depend on the user's PC board layout, the chassis shielding environment and choice of external components. Please refer to Application Note GEAN-02 for further discussion. Since many factors affect both the amplitude and spectra of emissions, we recommend using an engineer who is experienced at emissions suppression. www.murata-ps.com/support MDC_RBQ-12/33-D48.A01 Page 14 of 15 RBQ-12/33-D48 Quarter-Brick 400-Watt Isolated DC-DC Converters Vertical Wind Tunnel IR Transparent optical window Variable speed fan Unit under test (UUT) Murata Power Solutions employs a computer controlled custom-designed closed loop vertical wind tunnel, infrared video camera system, and test instrumentation for accurate airflow and heat dissipation analysis of power products. The system includes a precision low flow-rate anemometer, variable speed fan, power supply input and load controls, temperature gauges, and adjustable heating element. The IR camera monitors the thermal performance of the Unit Under Test (UUT) under static steady-state conditions. A special optical port is used which is transparent to infrared wavelengths. IR Video Camera Heating element Precision low-rate anemometer 3" below UUT Both through-hole and surface mount converters are soldered down to a 10"x 10" host carrier board for realistic heat absorption and spreading. Both longitudinal and transverse airflow studies are possible by rotation of this carrier board since there are often significant differences in the heat dissipation in the two airflow directions. The combination of adjustable airflow, adjustable ambient heat, and adjustable Input/Output currents and voltages mean that a very wide range of measurement conditions can be studied. The collimator reduces the amount of turbulence adjacent to the UUT by minimizing airflow turbulence. Such turbulence influences the effective heat transfer characteristics and gives false readings. Excess turbulence removes more heat from some surfaces and less heat from others, possibly causing uneven overheating. Ambient temperature sensor Airflow collimator Both sides of the UUT are studied since there are different thermal gradients on each side. The adjustable heating element and fan, built-in temperature gauges, and no-contact IR camera mean that power supplies are tested in real-world conditions. Figure 9. Vertical Wind Tunnel Soldering Guidelines Murata Power Solutions recommends the specifications below when installing these converters. These specifications vary depending on the solder type. Exceeding these specifications may cause damage to the product. Your production environment may differ; therefore please thoroughly review these guidelines with your process engineers. Wave Solder Operations for through-hole mounted products (THMT) For Sn/Ag/Cu based solders: Maximum Preheat Temperature For Sn/Pb based solders: 115 C. Maximum Preheat Temperature 105 C. Maximum Pot Temperature 270 C. Maximum Pot Temperature 250 C. Maximum Solder Dwell Time 7 seconds Maximum Solder Dwell Time 6 seconds Murata Power Solutions, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A. ISO 9001 and 14001 REGISTERED This product is subject to the following operating requirements and the Life and Safety Critical Application Sales Policy: Refer to: http://www.murata-ps.com/requirements/ Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. (c) 2013 Murata Power Solutions, Inc. www.murata-ps.com/support MDC_RBQ-12/33-D48.A01 Page 15 of 15 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Murata: RBQ-12/33-D48NBSH-C RBQ-12/33-D48PBS-C RBQ-12/33-D48NB-C RBQ-12/33-D48PBSH-C RBQ-12/33-D48PBC RBQ-12/33-D48NBS-C RBQ-12/33-D48NBH-C RBQ-12/33-D48PBH-C