SERIES SMA, SUBMINIATURE CONNECTORS DESCRIPTION CONTENTS HUBER+SUHNER SMA connectors are precision connectors for microwave applications up to 18 GHz. They distinguish themselves through their high mechanical strength, high durability, high reliability and low VSWR. Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 Interface dimensions . . . . . . . . . . . . . . . . . . . . . . 115 Interface dimensions in mm / inches . . . . . . . . . . . 115 Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 Cable connectors . . . . . . . . . . . . . . . . . . . . . . . . 118 Receptacles with solder end . . . . . . . . . . . . . . . 128 Receptacles with coaxial end . . . . . . . . . . . . . . . 130 Stripline launchers . . . . . . . . . . . . . . . . . . . . . . . . 131 Microstrip launchers . . . . . . . . . . . . . . . . . . . . . 133 Connectors with hermetic seal . . . . . . . . . . . . . . 133 PCB connectors . . . . . . . . . . . . . . . . . . . . . . . . . 135 Protective caps and shorts . . . . . . . . . . . . . . . . . 136 SMA Launchers with Transition Pins . . . . . . . . . . . 137 INTERFACE DIMENSIONS INTERFACE DIMENSIONS (MM / INCHES) Plug Plug (male) Jack (female) Jack min. max. min. max. A --- 4.59/.181 4.59/.181 --- B 0.00/.000 0.25/.010 0.00/.000 0.25/.010 C 0.00/.000 0.25/.010 0.00/.000 0.25/.010 D --- 2.54/.100 2.67/.105 --- E 1.24/.049 1.29/.051 1.24/.049 1.29/.051 F 0.38/.015 1.14/.045 1.88/.074 1.98/.078 G --- 3.43/.135 0.38/.015 1.14/.045 H 0.90/.036 0.94/.037 5.28/.208 5.49/.216 I --- --- 4.32/.170 --- K --- --- 5.54/.218 --- IP rating (interface, mated) IP68 HUBER+SUHNER SMA 115 SMA SMA launchers are the preferred connection element for varied microwave circuits. There is a huge variety of applications for HUBER+SUHNER SMA connectors, such as mobile communication, test & measurement, instruments, avionics, etc. PAGE Interface dimensions conformable to the Standards: International: Europe: USA: IEC 60169-15 CECC 22110 MIL-C-39012, SMA Interface MIL-STD-348a/310 BS 9210 N 0006 NF-C-93563 (KMR) GB: F: TECHNICAL DATA ELECTRICAL DATA MIL-C-39012 Cable type semi-rigid Cable dielectric diameter (mm/in.) flexible 1.5 / .066 3 / .117 1.5 / .066 3 / .117 50 8 Impedance Frequency range for interface DC ... 18 GHz VSWR (typical value) see table below RF-leakage measured at 3 GHz (f in GHz) 3.26 Dielectric withstanding voltage (at sea level, in V rms, 50 Hz) 3.17 100 dB-f 1000 1500 750 1000 335 500 250 335 250 375 190 250 85 125 65 85 670 1000 500 670 Working voltage (at sea level, in V rms, 50 Hz) Corona extinction voltage (at 21 000 m/70 000 ft., in V rms, 50 Hz) 3.22 Working voltage (at 21 000 m/70 000 ft., in V rms, 50 Hz) RF withstanding voltage at 5 MHz (V rms) 3.23 Insulation resistance 3.11 Contact resistance - centre contact - outer contact 3.16 60 dB 5*103 M8 $ 3m8 $ 2.5 m8 TYPICAL VSWR FREQUENCY RANGE CONNECTOR TYPE 1 GHz 2.5 GHz 5 GHz 12.4 GHz 18 GHz CABLE GROUP straight connectors 1.03 1.03 1.03 1.07 1.08 Y3, Y11 1.03 1.03 1.04 1.07 1.15 Y5, Y12 1.05 1.07 1.08 U2, U4 1.04 1.05 1.07 U7, U9 1.03 1.05 1.10 1.25 Y3, Y11 1.03 1.05 1.08 1.17 Y5, Y12 1.05 1.07 1.11 U2, U4 1.03 1.05 1.07 U7, U9 right angle connectors 116 HUBER+SUHNER SMA MECHANICAL DATA MIL-C-39012 standard: brass: Recommended coupling nut torque Coupling nut retention force 3.25 Contact captivation - axial 3.12 Cable retention 0.8 Nm ... 1.1 Nm / 7.1 in. lbs. ... 9.7 in. lbs 0.45 Nm / 4.0 in. lbs 270 N / 60.7 lbs 27 N / 6.1 lbs force1) see pages 28 - 34 Durability (matings) $ 500 1) Value considers maximum load of the cables without irreversible variations of specifications. TEST CONDITIONS Temperature range - 65qC ... + 165qC / - 85 qF ... + 329 qF Climatic category IEC o 55/155/21 Thermal shock MIL-STD-202, Method 107, Condition B Moisture resistance MIL-STD-202, Method 106 Corrosion Saltspray test acc. to MIL-STD-202, Method 101, Condition B Vibration MIL-STD-202, Method 204, Condition D Shock MIL-STD-202, Method 213, Condition I SMA ENVIRONMENTAL DATA MATERIAL DATA CONNECTOR PART MATERIAL PLATING Bodies, outer contacts copper-beryllium alloy stainless steel brass spring bronze gold passivated SUCOPLATE, gold gold Pin contacts copper-beryllium alloy, brass gold Socket contacts copper-beryllium alloy spring bronze gold Crimp ferrules copper, brass gold Insulators PTFE or PFA Gaskets silicone rubber Some connectors may have a specification that differs from the above mentioned data. The products are designed and guaranteed to pass the above mentioned test procedures. Any additional or different requirement arising from specific applications or environmental conditions which is not covered by these test procedures is subject to request. HUBER+SUHNER SMA 117 CABLE CONNECTORS Straight cable plugs (male) > for semi-rigid cables > with pin and insulator > cable entry soldered > centre contact soldered > compound 74_Z-0-0-116 needed (see page 398) HUBER+SUHNER type Item no. Cable group (example) Packaging Assembly instruction Plating body 11_SMA-50-1-1/111_NE 22642387 Y1 (EZ 34) single 9118 gold 11_SMA-50-1-2/111_NE 22642388 Y2 (EZ 47) single 9119 gold Cable group (example) Packaging Assembly instruction Plating body Y3, Y11 bulk 100 pcs. 9056 gold > for semi-rigid cables > with pin and insulator > cable entry soldered > centre contact soldered Fig. 1 Fig. 2 HUBER+SUHNER type Item no. Fig. 11_SMA-50-2-15/111_NH U 22645898 11_SMA-50-2-29/119_NH U 22660366 Y3, Y11 (EZ 86) bulk 100 pcs. 27334 stainless 11_SMA-50-2-65/119_NH U 22645366 Y3, Y11 (EZ 86) bulk 100 pcs. 9056 stainless steel2) 1 (EZ 86) 1) centre contact plugged-in 1 steel2) 21) 2) cable entry CuBe/gold > for semi-rigid cables > without pin and insulator > cable entry soldered HUBER+SUHNER type Item no. 11_SMA-50-3-14/-11_NH U 22644467 11_SMA-50-3-64/-19_NH U 22649224 Cable group (example) Packaging Assembly instruction Plating body Y5 bulk 100 pcs. 9055 gold Y5 (EZ 141) (EZ 141) bulk 100 pcs. 118 stainless 26.5 GHz steel2) 26.5 GHz 2) cable entry CuBe/gold U centre contact NOT captivated Cable groups see page 28 9055 Notes Assembly tools see page 385 HUBER+SUHNER SMA Mounting holes see page 412 > for semi-rigid cables > with pin and insulator > cable entry soldered > centre contact soldered Fig. 2 HUBER+SUHNER type Item no. Cable group (example) Packaging Assembly instruction Plating body Y5, Y12 bulk 100 pcs. 9056 gold Fig. 11_SMA-50-3-15/111_NH U 22651601 11_SMA-50-3-65/119_NH U 22646570 Y5, Y12 (EZ 141) bulk 100 pcs. 9056 stainless 11_SMA-50-3-39/111_YH 23026120 Y5, Y12 (EZ 141) bulk 100 pcs. 150012 SUCOPRO (EZ 141) 1) centre contact plugged-in 1 steel2) 1 21) 2) cable entry CuBe/gold > for semi-rigid cables > without pin and insulator > cable entry soldered > short version HUBER+SUHNER type 11_SMA-50-3-16/-11_NH Item no. U 22644470 11_SMA-50-3-42/-33_NH U 22646128 11_SMA-50-3-66/-19_NH U 22645207 Cable group (example) Packaging Assembly instruction Plating body Notes Y5 bulk 100 pcs. 9055 gold 26.5 GHz 9055 SUCOPLATE1) 26.5 GHz 9055 steel2) 26.5 GHz (EZ 141) Y5 (EZ 141) Y5 (EZ 141) bulk 100 pcs. bulk 100 pcs. 1) use torque wrench 74_Z-0-0-79 stainless 2) cable entry CuBe/gold > for flexible cables > cable entry clamp > centre contact soldered HUBER+SUHNER type Item no. Cable group (example) Packaging Assembly instruction Plating body 11_SMA-50-3-7/111_NE 22640050 U7 (RG 58 C/U) single 3071 gold 11_SMA-50-3-8/111_NH 22648630 U10 (RG 223/U) bulk 100 pcs. 3071 gold 11_SMA-50-3-10/111_NE 22640053 U10 (RG 223/U) single 3071 gold U centre contact NOT captivated Cable groups see page 28 Assembly tools see page 385 HUBER+SUHNER SMA Mounting holes see page 412 119 SMA Fig. 1 > for flexible cables > cable entry crimp > centre contact soldered > taper sleeves see page 406 HUBER+SUHNER type Item no. Cable group (example) Packaging Assembly instruction Plating body Crimp insert 11_SMA-50-1-4/111_NE 22645871 U1 (RG 178 B/U) single 27061 gold A 11_SMA-50-2-5/111_NH 22646312 U2 (RG 316/U) bulk 100 pcs. 27266 gold A 11_SMA-50-2-6/111_NH 22650740 U4 (K 02252 D) bulk 100 pcs. 27266 gold A 11_SMA-50-2-27/111_NH 22652923 U2 (RG 316/U) bulk 100 pcs. 27164 gold 1 A 1) 11_SMA-50-2-41/133_NH 22652160 U4 (K 02252 D) bulk 100 pcs. 3069 SUCOPLATE2) A 11_SMA-50-2-42/133_NH 22648783 U2 (RG 316/U) bulk 100 pcs. 27266 SUCOPLATE2) A 11_SMA-50-2-55/199_NE 22641377 U2 (RG 316/U) single 3069 stainless steel A 11_SMA-50-2-56/199_NH 22651486 U4 (K 02252 D) bulk 100 pcs. 3069 stainless steel A 1) HUBER+SUHNER full crimp 2) use torque wrench 74_Z-0-0-79 > for flexible cables > cable entry crimp > centre contact soldered > taper sleeves see page 406 HUBER+SUHNER type Item no. Cable group (example) Packaging Assembly instruction Plating body Crimp insert 11_SMA-50-3-5/111_NE 22640048 U7 single 3069 gold B 11_SMA-50-3-6/111_NH 22650739 U9, 11 bulk 100 pcs. 3069 gold B 3069 SUCOPLATE1) B bulk 100 pcs. 3069 SUCOPLATE1) B single 3069 stainless steel B bulk 100 pcs. 3069 stainless steel B 11_SMA-50-3-45/133_NH 22645987 (RG 58 C/U) U7 (RG 400/U) (RG 58 C/U) 11_SMA-50-3-46/133_NH 22651819 U9, 11 11_SMA-50-3-55/199_NE 22641371 U7 11_SMA-50-3-56/199_NH 22648300 U9, 11 (RG 400/U) (RG 58 C/U) (RG 400/U) bulk 100 pcs. 1) use torque wrench 74_Z-0-0-79 Cable groups see page 28 120 Assembly tools see page 385 HUBER+SUHNER SMA Mounting holes see page 412 Right angle cable plugs (male) > for semi-rigid cables > cable entry soldered SMA > centre contact soldered HUBER+SUHNER type Item no. Cable group (example) Packaging Assembly instruction Plating body 16_SMA-50-2-43/133_NE 22641953 Y3, Y11 (EZ 86) single 3068 SUCOPLATE1) 16_SMA-50-2-53/119_NH 22646639 Y3, Y11 (EZ 86) bulk 100 pcs. 3068 stainless steel2) 16_SMA-50-2-103/111_NH 22652924 Y3, Y11 (EZ 86) bulk 100 pcs. 3068 gold 1) use torque wrench 74_Z-0-0-79 Notes 2) cable entry CuBe/gold > for semi-rigid cables > cable entry soldered > centre contact soldered HUBER+SUHNER type Item no. Cable group (example) Packaging Assembly instruction Plating body 16_SMA-50-3-3/111_NH 22646569 Y5, Y12 (EZ 141) bulk 100 pcs. 3068 gold 16_SMA-50-3-43/133_NE 22642241 Y5, Y12 (EZ 141) single 3070 SUCOPLATE1) Notes 1) use torque wrench 74_Z-0-0-79 Cable groups see page 28 Assembly tools see page 385 HUBER+SUHNER SMA Mounting holes see page 412 121 > for flexible cables > cable entry crimp > centre contact soldered > taper sleeves see page 406 HUBER+SUHNER type Item no. Cable group (example) Packaging Assembly instruction Plating body Crimp insert 16_SMA-50-1-1/111_NH 22660358 U1 (RG 178 B/U) bulk 100 pcs. 3070 gold A 16_SMA-50-2-105/111_NH 22651456 U2 (RG 316/U) bulk 100 pcs. 3070 gold A 16_SMA-50-2-106/111_NH 22651458 U4 (K 02252 D) bulk 100 pcs. 3070 gold A 3070 SUCOPLATE1) A bulk 100 pcs. 3070 SUCOPLATE1) A 16_SMA-50-2-141/133_NH 16_SMA-50-2-145/133_NH 22651997 U4 (K 02252 D) bulk 100 pcs. 22652929 U2 HUBER+SUHNER type Item no. Cable group (example) Packaging Assembly instruction Plating body Crimp insert 16_SMA-50-3-105/111_NH 22651800 U7 (RG 58 C/U) bulk 100 pcs. 3070 gold B 16 _SMA-50-3-106/111_NH 22650545 U9, 11 (RG 400/U) bulk 100 pcs. 3070 gold B 3070 SUCOPLATE1) B 3070 SUCOPLATE1) B (RG 316/U) > for flexible cables > cable entry crimp > centre contact soldered > taper sleeves see page 406 16_SMA-50-3-145/133_NE 16_SMA-50-3-146/133_NE 22651584 22649909 U7 (RG 58 C/U) U9, 11 (RG 400/U) single single 1) use torque wrench 74_Z-0-0-79 Cable groups see page 28 122 Assembly tools see page 385 HUBER+SUHNER SMA Mounting holes see page 412 Straight cable jacks (female) > for semi-rigid cables > cable entry soldered > centre contact soldered Fig. 2 HUBER+SUHNER type Item no. Cable group (example) Packaging Assembly instruction Plating body Fig. 21_SMA-50-1-1/111_NE 22642385 Y1 (EZ 34) single 9118 gold 1 21_SMA-50-1-2/111_NE 22642386 Y2 (EZ 47) single 9119 gold 1 22652141 Y3, Y11 (EZ 86) bulk 100 pcs. 9057 gold 2 HUBER+SUHNER type Item no. Cable group (example) Packaging Assembly instruction Plating body Notes 21_SMA-50-3-47/111_YE 23025549 Y5 bulk 100 pcs. 150012 SUCOPRO 21_SMA-50-2-15/111_NH U > for semi-rigid cables > cable entry soldered > centre contact plugged-in (EZ 141) U centre contact NOT captivated Cable groups see page 28 Assembly tools see page 385 HUBER+SUHNER SMA Mounting holes see page 412 123 SMA Fig. 1 > for flexible cables > cable entry crimp > centre contact soldered > taper sleeves see page 406 HUBER+SUHNER type Item no. Cable group (example) Packaging Assembly instruction Plating body Crimp insert 21_SMA-50-2-5/111_NE 22640077 U2 (RG 316/U) single 3069 gold A 21_SMA-50-2-6/111_NH 22651818 U4 (K 02252 D) bulk 100 pcs. 3069 gold A HUBER+SUHNER type Item no. Cable group (example) Packaging Assembly instruction Plating body Crimp insert 21_SMA-50-3-5/111_NE 22640081 U7 (RG 58 C/U) single 3069 gold B 21_SMA-50-3-6/111_NE 22640082 U9, 11 (RG 400/U) single 3069 gold B > for flexible cables > cable entry crimp > centre contact soldered > taper sleeves see page 406 Straight bulkhead cable jacks (female) > for semi-rigid cables > cable entry soldered > centre contact soldered > with panel seal > insulating washers see page 408 HUBER+SUHNER type 24_SMA-50-2-15/111_NH U Item no. Cable group (example) Packaging Assembly instruction Plating body Mounting hole 22645490 Y3, Y11 bulk 100 pcs. 9057 gold ML 35 (EZ 86) U centre contact NOT captivated Cable groups see page 28 124 Assembly tools see page 385 HUBER+SUHNER SMA Mounting holes see page 412 > for semi-rigid cables > cable entry soldered > centre contact soldered > with panel seal > insulating washers see page 408 HUBER+SUHNER type U Cable group (example) Packaging Assembly instruction Plating body Mounting hole 22645259 Y5, Y12 bulk 100 pcs. 9057 gold ML 35 (EZ 141) SMA 24_SMA-50-3-15/111_NH Item no. > for flexible cables > cable entry crimp > centre contact soldered > with panel seal > taper sleeves see page 406 HUBER+SUHNER type Item no. Cable group (example) Packaging Assembly Instruction/ Mounting Hole 24_SMA-50-2-13/111_NH 22651719 U4 (K 02252 D) bulk 100 pcs. 3069 / ML 20 gold A 24_SMA-50-2-14/111_NH 22651747 U2 (RG 316/U) bulk 100 pcs. 3069 / ML 20 gold A A Plating body Crimp insert 24_SMA-50-2-45/133_NH 22652352 U4 (K 02252 D) bulk 100 pcs. 3069 / ML 20 SUCOPLATE1) 24_SMA-50-2-45/133_UH 22648472 U4 (K 02252 D) bulk 100 pcs. 3069 / ML 20 SUCOPLATE1) A 3069 / ML 20 SUCOPLATE1) A 24_SMA-50-2-46/133_NH 22646565 U2 (RG 316/U) bulk 100 pcs. 1) use torque wrench 74_Z-0-0-79 U centre contact NOT captivated Cable groups see page 28 Assembly tools see page 385 HUBER+SUHNER SMA Mounting holes see page 412 125 > for flexible cables > cable entry crimp > centre contact soldered > taper sleeves see page 406 HUBER+SUHNER type Item no. Cable group (example) Packaging Assembly Instruction/ Mounting Hole 24_SMA-50-3-42/133_NE 22641358 U9 single 3072 / ML 20 (RG 223/U) Plating body Crimp insert SUCOPLATE1) B 1) use torque wrench 74_Z-0-0-79 Straight panel cable jacks (female) > for semi-rigid cables > cable entry soldered > centre contact soldered Fig. 1 Fig. 2 HUBER+SUHNER type Item no. Cable group (example) Packaging Assembly instruction/ Mounting hole Plating body Fig. 25_SMA-50-1-2/111_NE 22642390 Y2 (EZ 47) single 9119 / ML 19 gold 1 25_SMA-50-1-4/111_NE 22642391 Y2 (EZ 47) single 9119 gold 2 Cable groups see page 28 126 Assembly tools see page 385 HUBER+SUHNER SMA Mounting holes see page 412 > for semi-rigid cables > cable entry soldered > centre contact soldered Fig. 2 HUBER+SUHNER type Item no. Cable group (example) Packaging Assembly instruction/ Mounting hole Plating body Fig. 25_SMA-50-2-15/111_NE U 22544551 Y3, Y11 (EZ 86) single 9057 / ML 19 gold 1 25_SMA-50-2-25/111_NE U 22641493 Y3, Y11 (EZ 86) single 9057 gold 2 > for semi-rigid cables > cable entry soldered > centre contact soldered Fig. 1 Fig. 2 HUBER+SUHNER type Item no. Cable group (example) Packaging Assembly instruction/ Mounting hole Plating body Fig. 25_SMA-50-3-15/111_NH U 22644717 Y5, Y12 (EZ 141) bulk 100 pcs. 9057 / ML 19 gold 1 25_SMA-50-3-25/111_NH U 22646563 Y5, Y12 (EZ 141) bulk 100 pcs. 9057 gold 2 U centre contact NOT captivated Cable groups see page 28 Assembly tools see page 385 HUBER+SUHNER SMA Mounting holes see page 412 127 SMA Fig. 1 > for flexible cables > cable entry crimp > centre contact soldered > square flange > taper sleeves see page 406 HUBER+SUHNER type Item no. Cable group (example) Packaging Assembly instruction/ Mounting hole Plating body Crimp insert 25_SMA-50-2-5/111_NH 22650755 U2 (RG 316/U) bulk 100 pcs. 3072 / ML 19 gold A 25_SMA-50-2-6/111_NE 22640113 U4 (K 02252 D) single 3072 / ML 19 gold A 3072 / ML 19 SUCOPLATE1) A 25_SMA-50-2-46/133_NE 22642246 U4 (K 02252 D) single 1) use torque wrench 74_Z-0-0-79 RECEPTACLES WITH SOLDER END Receptacles, jacks (female) > bulkhead mounted > with panel seal HUBER+SUHNER type Item no. Packaging Plating body Mounting hole Notes 22_SMA-50-0-1/111_NE 22640087 single gold ML 20 rear mounting Cable groups see page 28 128 Assembly tools see page 385 HUBER+SUHNER SMA Mounting holes see page 412 Receptacles, jacks (female) > rear mounting > without panel seal > insulating washers see page 408 HUBER+SUHNER type Item no. Packaging Plating body Mounting hole 22_SMA-50-0-4/111_NH 22649418 bulk 100 pcs. gold ML 35 ML 35 22643518 single 22_SMA-50-0-203/111_NH 22652012 bulk 100 pcs. gold ML 35 HUBER+SUHNER type Item no. Packaging Plating body Notes 23_SMA-50-0-1/111_NH 22651409 bulk 100 pcs. gold 23_SMA-50-0-44/133_NH 22652098 bulk 100 pcs. SUCOPLATE 23_SMA-50-0-51/199_NE 22543948 single stainless steel HUBER+SUHNER type Item no. Packaging Plating body 23_SMA-50-0-11/111_NE 22640095 single gold 23_SMA-50-0-41/133_NH 22644383 bulk 100 pcs. SUCOPLATE 23_SMA-50-0-61/199_NE 22544796 single stainless steel use torque wrench 74_Z-0-0-79 SMA 22_SMA-50-0-44/133_NE SUCOPLATE Notes > panel mounted use torque wrench 74_Z-0-0-79 > panel mounted Cable groups see page 28 Notes use torque wrench 74_Z-0-0-79 Assembly tools see page 385 HUBER+SUHNER SMA Mounting holes see page 412 129 Right angle receptacles, jack (female) > bulkhead mounted > without panel seal > insulating washers see page 408 HUBER+SUHNER type Item no. Packaging Plating body Mounting hole 27_SMA-50-0-11/111_NE 22544384 single gold ML 35 HUBER+SUHNER type Item no. Packaging Plating body Notes 28_SMA-50-0-1/111_NH 22650703 bulk 100 pcs. gold 28_SMA-50-0-41/133_NH 22645468 bulk 100 pcs. SUCOPLATE use torque wrench 74_Z-0-0-79 Notes > panel mounted RECEPTACLES WITH COAXIAL END Receptacles, jacks (female) > bulkhead mounted HUBER+SUHNER type Item no. Packaging Plating body Mounting hole Notes 22_SMA-50-0-3/111_NE 22640089 single gold ML 98 tap drill 74_Z-0-0-24 22_SMA-50-0-53/199_NE 22543498 single stainless steel ML 98 tap drill 74_Z-0-0-24 Cable groups see page 28 130 Assembly tools see page 385 HUBER+SUHNER SMA Mounting holes see page 412 Receptacles, jacks (female) > panel mounted Item no. Packaging Plating body Notes 23_SMA-50-0-21/111_NE 22640101 single gold flush dielectric SMA HUBER+SUHNER type Fig. 1 Fig. 2 HUBER+SUHNER type Item no. Packaging Plating body Notes Fig. 23_SMA-50-0-3/111_NE 22640092 single gold extended dielectric 1 23_SMA-50-0-13/111_NH 22658873 bulk 100 pcs. gold extended dielectric 2 23_SMA-50-0-53/199_NE 22641394 single stainless steel extended dielectric 1 STRIPLINE LAUNCHERS Panel launchers, male > tab contact HUBER+SUHNER type Item no. Packaging Plating body Notes 13_SMA-50-0-2/111_NE 22640056 single gold flush dielectric Cable groups see page 28 Assembly tools see page 385 HUBER+SUHNER SMA Mounting holes see page 412 131 Panel launchers, male > tab contact HUBER+SUHNER type Item no. Packaging Plating body 13_SMA-50-0-141/133_NH 22649018 bulk 100 pcs. SUCOPLATE1) flush dielectric HUBER+SUHNER type Item no. Packaging Plating body Notes 23_SMA-50-0-2/111_NE 22640091 single gold flush dielectric 23_SMA-50-0-52/199_NE 22543487 single stainless steel flush dielectric HUBER+SUHNER type Item no. Packaging Plating body Notes 23_SMA-50-0-12/111_NE 22640096 single gold flush dielectric 23_SMA-50-0-62/199_NE 22544779 single stainless steel flush dielectric Notes 1) use torque wrench 74_Z-0-0-79 Panel launchers, female > tab contact > tab contact Cable groups see page 28 132 Assembly tools see page 385 HUBER+SUHNER SMA Mounting holes see page 412 MICROSTRIP LAUNCHERS Panel launchers, female HUBER+SUHNER type Item no. Packaging Plating body Notes 23_SMA-50-0-4/111_NE 22640093 single gold flush dielectric SMA > tab contact, offset CONNECTORS WITH HERMETIC SEAL All hermetic seal SMA connectors use precision glass to metal seals, which are soldered into the connector body. Caution: max. soldering temperature for hermetic seal SMA connectors is 250qC / 482qF. Receptacle, male, hermetic seal > "Spark Plug" with metal ring seal > RoHs compliant alternative on request metal ring HUBER+SUHNER type Item no. Packaging Plating body Mounting hole Notes 12_SMA-50-0-110/111_NE 22652315 single gold ML 42 pressure max. 200 N/cm2 (290 psi) Cable groups see page 28 Assembly tools see page 385 HUBER+SUHNER SMA Mounting holes see page 412 133 Receptacle, female, hermetic seal > "Spark Plug" with metal ring seal > RoHS compliant alternative on request metal ring HUBER+SUHNER type Item no. Packaging Plating body Mounting hole Notes 22_SMA-50-0-10/111_NE 22641291 single gold ML 42 pressure max. 200 N/cm2 (290 psi) For type 12_SMA-50-0-110 (see previous page) and 22_SMA-50-0-10 (see above): Use assembly tool 74_Z-0-0-75 and torque wrench 74_Z-0-0-80! The specified torque of 200 Ncm (17.7 in. lbs) results in a leakage rate of 10-8 Torr l/sec. (atm cc/s) maximum. Receptacles, jacks (female) > bulkhead mounted > with panel seal > RoHS compliant alternative on request HUBER+SUHNER type Item no. Packaging Plating body Mounting hole Notes 22_SMA-50-0-12/111_NY 22641293 75 pcs. gold ML 98 pressure max. 200 N/cm2 (290 psi) 1) 1) leak rate 10-6 Torr l/sec.(atm cc/s) max. tap drill 74_Z-0-0-24 Receptacles, female, hermetic seal > bulkhead mounted for direct soldering > supplied with separate insulating bushing > RoHS compliant alternative on request insulating bushing HUBER+SUHNER type Item no. Packaging Plating body Mounting hole Notes 22_SMA-50-0-15/111_NE 22544588 single gold ML 96 pressure max. 200 N/cm2 (290 psi) 1) 1) leak rate 10-8 Torr l/sec.(atm cc/s) max. Cable groups see page 28 134 soldering temperature 250 C / 482 F max. Assembly tools see page 385 HUBER+SUHNER SMA Mounting holes see page 412 PCB CONNECTORS Straight PCB jacks (female) > without stand-off Item no. Packaging Plating body Mounting hole 82_SMA-50-0-1/111_NH 22644334 bulk 100 pcs. gold ML 41 HUBER+SUHNER type Item no. Packaging Plating body Mounting hole 82_SMA-50-0-45/111_NE 22652330 single gold ML 132 Notes SMA HUBER+SUHNER type > edge mount Notes Right angle PCB jacks (female) > without stand-off HUBER+SUHNER type Item no. Packaging Plating body Mounting hole 85_SMA-50-0-101/111_NH 22652140 bulk 100 pcs. gold ML 41 Cable groups see page 28 Assembly tools see page 385 HUBER+SUHNER SMA Notes Mounting holes see page 412 135 > with stand-off HUBER+SUHNER type 85_SMA-50-0-144/111_YH Item no. 23000527 Packaging Plating body Mounting hole bulk 100 pcs. SUCOPLATE ML 41 Notes PROTECTIVE CAPS AND SHORTS Cap with chain for jacks HUBER+SUHNER type Item no. Packaging Plating body Notes 62_SMA-0-0-1/-11_NE 22640159 single gold non-shorting, humidity sealed 62_SMA-0-0-51/-99_NE 22644252 single stainless steel non-shorting, humidity sealed HUBER+SUHNER type Item no. Packaging Plating body Notes 64_SMA-0-0-1/111_NE 22640161 single gold SMA plug, humidity sealed Shorting Caps Cable groups see page 28 136 Assembly tools see page 385 HUBER+SUHNER SMA Mounting holes see page 412 SMA LAUNCHERS WITH TRANSITION PINS flush design recessed design SMA SMA launchers have interchangeable transition pins and insulators. This design offers many advantages as: - connector replacement without disturbing the electronic circuit - improved mechanical performance - greater design flexibility (mechanical and electrical) - reduced inventory costs The launchers accept transition pins with a diameter of 0.92 mm/.036 in. Connectors and pins have to be ordered separately. All parts conform to MIL C-83517. Connector housings are available with recessed or flush rear contact. The PTFE dielectric is always flush with the connector flange back. Tab contact ACCEPTS O 0.92/ .036 DIA CONTACT ACCEPTS O 0.92/ .036 DIA CONTACT Fig. 1 Fig. 2 HUBER+SUHNER type Item no. Packaging Plating body Fig. Notes 23_SMA-0-165/199_NE 22644159 single stainless steel 1 flush design 23_SMA-0-166/199_NE 22644160 single stainless steel 2 flush design 23_SMA-0-167/199_NE 22644155 single stainless steel 1 recessed design 23_SMA-0-168/199_NE 22644156 single stainless steel 2 recessed design Cable groups see page 28 Assembly tools see page 385 HUBER+SUHNER SMA Mounting holes see page 412 137 Transition pins for flush launchers Tab contact HUBER+SUHNER type Item no. Packaging Plating 73_Z-0-0-138/1--_UZ 22644145 10 pins gold Notes Transition pins for recessed launchers Pin contact and insulator HUBER+SUHNER type Item no. Packaging Plating 73_Z-0-0-136/1--_UZ 22644151 10 pins and insulators gold HUBER+SUHNER type Item no. Packaging Plating 73_Z-0-0-141/1--_UZ 22644147 10 pins gold Notes Pin contact Cable groups see page 28 138 Assembly tools see page 385 HUBER+SUHNER SMA Notes Mounting holes see page 412 Tab contact Item no. Packaging Plating 73_Z-0-0-142/1--_UZ 22644148 10 pins gold HUBER+SUHNER type Item no. Packaging Plating 73_Z-0-0-151/1--_UZ 22644143 10 pins gold Notes SMA HUBER+SUHNER type Slotted contact Cable groups see page 28 Assembly tools see page 385 HUBER+SUHNER SMA Notes Mounting holes see page 412 139