HA17358/A Series Dual Operational Amplifier ADE-204-033 (Z) 1st Edition July 2000 Description HA17358 series and HA17358A series are dual operational amplifier that provide high gain and internal phase compensation, with single power supply. They can be widely applied to control equipments and to general use. Features * Wide range of supply voltage, and single power supply used * Wide range of common mode voltage, and possible to operate with an input about 0 V, and output around 0 V is available * Frequency characteristics and input bias current are temperature compensated Features only for "A" series * Low electro-magnetic susceptibility level Measurement Condition 5.0 Output Offset Voltage vs. Input Interference Vcc = +7.5 V Vee = -7.5 V Rs Rs - + Rf 0.01 Vin -10 dBm RF signal source (for quasi-RF noise) Vout V _ (= 100Vio) Output offset voltage (arb. unit) Rf 4.0 HA17358 series 3.0 2.0 Improvement 1.0 HA17358A series 0 -1.0 100E+3 1E+6 10E+6 100E+6 1E+9 Input RF frequency (Hz) 10E+9 Notice: The example of an applied circuit or combination with other equipment shown herein indicates characteristics and performance of semiconductor -applied products. The company shall assume no responsibility for any problem involving a patent caused when applying the descriptions in the example. HA17358/A Series Ordering Information HA17358 Series Type No. Application Package HA17358 Commercial use DP-8 HA17358F FP-8D HA17358A Series Type No. Application Package HA17358APS Industrial use DP-8 HA17358ARP FP-8DC HA17358AFP FP-8D 2 HA17358/A Series Pin Arrangement Vout1 1 Vin(-)1 2 Vin(+)1 3 GND 4 1 - + 2 + - 8 VCC 7 Vout2 6 Vin(-)2 5 Vin(+)2 (Top View) Circuit Schematic (1/2) Q5 Vin(-) Q1 Q2 Q3 Q4 Q6 Q7 C R1 Vin(+) Vout Q11 Q10 Q8 Q13 Q12 Q9 3 HA17358/A Series Absolute Maximum Ratings (Ta = 25C) Ratings Item Symbol HA17358/APS HA17358F/AFP/ARP Unit Supply voltage VCC 32 32 V Sink current Isink 50 50 1 mA 2 Power dissipation PT 570 * 385 * mW Common mode input voltage VCM -0.3 to VCC -0.3 to VCC V Differential input voltage Vin (diff) VCC VCC V Operating temperature Topr -20 to +75 -20 to +75 C Storage temperature Tstg -55 to +125 -55 to +125 C Notes: 1. This is the allowable values up to Ta = 50C. Derate by 8.3 mW/C. 2. This is the allowable value up to Ta = 45C mounting on 30% wiring density glass epoxy board. Derate by 7.14 mW/C above that temperature. 4 HA17358/A Series Electrical Characteristics (VCC = +15 V, Ta = 25C) Item Symbol Min Typ Max Unit Test Conditions Input offset voltage VIO -- 3 7 mV VCM = 7.5V, RS = 50, Rf = 50k Input offset current I IO -- 5 50 nA VCM = 7.5V, IIO = | II (+) - I I (-) | Input bias current I IB -- 30 250 nA VCM = 7.5V Power source rejection ratio PSRR -- 93 -- dB RS = 1k, Rf = 100k Voltage gain AVD 75 90 -- dB RL = , RS = 1k, Rf = 100k Common mode rejection ratio CMR -- 80 -- dB RS = 50, Rf = 5k Common mode input voltage range VCM (+) 13.5 -- -- V RS = 1k, Rf = 100k VCM (-) -- -- -0.3 V RS = 1k, Rf = 100k Peak-to-peak output voltage Vop-p -- 13.6 -- V f = 100Hz, RL = 20k, RS = 1k, Rf = 100k Output source current Iosource 20 40 -- mA VIN+ = 1V, VIN- = 0V, VOH = 10V Output sink current Iosink 10 20 -- mA VIN- = 1V, VIN+ = 0V, VOL = 2.5V Output sink current Iosink 15 50 -- A VIN- = 1V, VIN+ = 0V, Vout = 200mV Supply current I CC -- 0.8 2 mA VIN = GND, RL = Slew rate SR -- 0.2 -- V/s RL = , VCM = 7.5V, f = 1.5kHz Channel separation CS -- 120 -- dB f = 1kHz 5 HA17358/A Series Output Source Current vs. Ambient Temperature 80 VCC = 15 V 70 VOH = 10 V 60 50 40 30 20 10 0 -20 0 20 40 60 Ambeint temperature Ta (C) Input Bias Current vs. Ambient Temperature 80 Input bias current IIB (nA) Output source current Iosource (mA) Characteristic Curves VCC = 15 V VCM = 7.5 V 70 60 50 40 30 20 10 0 -20 80 2 1 8 16 24 32 Supply voltage VCC (V) 80 Input bias current IIB (nA) Supply current ICC (mA) Ta = 25C 3 0 40 20 0 40 Ta = 25C RL = 120 80 40 40 Maximum output voltage VOP-P (V) Voltage gain AVD (dB) 6 8 16 24 32 Supply voltage VCC (V) 40 Maxlmum Output Voltage vs. Frequency 160 8 16 24 32 Supply voltage VCC (V) Ta = 25C 60 Voltage Gain vs. Supply Voltage 0 80 Input Bias Current vs. Supply Voltage Supply Current vs. Supply Voltage 4 0 20 40 60 Ambeint temperature Ta (C) 20 VCC = 15 V Ta = 25C RL = 20 k 16 12 8 4 0 1k 3k 10 k 30 k 100 k 300 k Frequency f (Hz) 1M HA17358/A Series Voltage Gain vs. Frequency 120 VCC = 15V Ta = 25C RL = 80 60 40 20 0 1 3 10 30 100 300 1k 3k Frequency f (Hz) 10 k 30 k 100 k 300 k 1M Common Mode Rejection Ratio vs. Frequency 120 Common mode rejection ratio CMR (dB) Voltage gain AVD (dB) 100 VCC = 15V Ta = 25C RS = 50 100 80 60 40 20 0 100 300 1k 3 k 10 k 30 k 100 k 300 k Frequency f (Hz) 1M 7 HA17358/A Series Solder Mounting Method 1. Small and light surface-mount packages require spicial attentions on solder mounting. On solder mounting, pre-heating before soldering is needed. The following figure show an example of infrared rays refow. Temperature 2. The difference of thermal expansion coefficeient between mounted substrates and IC leads may cause a failure like solder peeling or soler wet, and electrical characteristics may change by thermal stress. Therefore, mounting should be done after sufficient confirmation for especially in case of ceramic substrates. 235C Max 10 s Max 140 to 160C 60 s 1 to 4C/s 1 to 5C/s Time (s) Figure 1 An Example of Infrared Rays Reflow Conditions 8 HA17358/A Series Package Dimensions Unit: mm 6.3 7.4 Max 9.6 10.6 Max 8 5 1 0.89 4 1.3 7.62 0.1 Min 2.54 Min 5.06 Max 1.27 Max + 0.10 0.25 - 0.05 0.48 0.10 2.54 0.25 0 - 15 Hitachi Code JEDEC EIAJ Mass (reference value) DP-8 Conforms Conforms 0.54 g Unit: mm 4.85 4.4 5.25 Max 5 8 1 0.75 Max *0.22 0.05 0.20 0.04 2.03 Max 4 0.25 6.50 +- 0.15 1.05 1.27 *0.42 0.08 0.40 0.06 0.10 0.10 0 - 8 0.25 0.60 +- 0.18 0.15 0.12 M *Dimension including the plating thickness Base material dimension Hitachi Code JEDEC EIAJ Mass (reference value) FP-8D -- Conforms 0.10 g 9 HA17358/A Series Unit: mm 3.95 4.90 5.3 Max 5 8 *0.22 0.03 0.20 0.03 4 1.75 Max 1 0.75 Max + 0.10 6.10 - 0.30 1.08 0.14 - 0.04 *0.42 0.08 0.40 0.06 + 0.11 0 - 8 1.27 + 0.67 0.60 - 0.20 0.15 0.25 M *Dimension including the plating thickness Base material dimension 10 Hitachi Code JEDEC EIAJ Mass (reference value) FP-8DC Conforms -- 0.085 g HA17358/A Series Cautions 1. Hitachi neither warrants nor grants licenses of any rights of Hitachi's or any third party's patent, copyright, trademark, or other intellectual property rights for information contained in this document. Hitachi bears no responsibility for problems that may arise with third party's rights, including intellectual property rights, in connection with use of the information contained in this document. 2. Products and product specifications may be subject to change without notice. Confirm that you have received the latest product standards or specifications before final design, purchase or use. 3. Hitachi makes every attempt to ensure that its products are of high quality and reliability. However, contact Hitachi's sales office before using the product in an application that demands especially high quality and reliability or where its failure or malfunction may directly threaten human life or cause risk of bodily injury, such as aerospace, aeronautics, nuclear power, combustion control, transportation, traffic, safety equipment or medical equipment for life support. 4. Design your application so that the product is used within the ranges guaranteed by Hitachi particularly for maximum rating, operating supply voltage range, heat radiation characteristics, installation conditions and other characteristics. Hitachi bears no responsibility for failure or damage when used beyond the guaranteed ranges. Even within the guaranteed ranges, consider normally foreseeable failure rates or failure modes in semiconductor devices and employ systemic measures such as failsafes, so that the equipment incorporating Hitachi product does not cause bodily injury, fire or other consequential damage due to operation of the Hitachi product. 5. This product is not designed to be radiation resistant. 6. No one is permitted to reproduce or duplicate, in any form, the whole or part of this document without written approval from Hitachi. 7. Contact Hitachi's sales office for any questions regarding this document or Hitachi semiconductor products. Hitachi, Ltd. Semiconductor & Integrated Circuits. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan Tel: Tokyo (03) 3270-2111 Fax: (03) 3270-5109 URL NorthAmerica Europe Asia Japan : : : : http://semiconductor.hitachi.com/ http://www.hitachi-eu.com/hel/ecg http://www.hitachi.com.sg/grp3/sicd http://www.hitachi.co.jp/Sicd/indx.htm For further information write to: Hitachi Semiconductor (America) Inc. 179 East Tasman Drive, San Jose,CA 95134 Tel: <1> (408) 433-1990 Fax: <1>(408) 433-0223 Hitachi Europe GmbH Electronic Components Group Dornacher Strae 3 D-85622 Feldkirchen, Munich Germany Tel: <49> (89) 9 9180-0 Fax: <49> (89) 9 29 30 00 Hitachi Asia Ltd. 16 Collyer Quay #20-00 Hitachi Tower Singapore 049318 Tel: 535-2100 Fax: 535-1533 Hitachi Europe Ltd. Electronic Components Group. Whitebrook Park Lower Cookham Road Maidenhead Berkshire SL6 8YA, United Kingdom Tel: <44> (1628) 585000 Fax: <44> (1628) 585160 Hitachi Asia Ltd. Taipei Branch Office 3rd Flr, Hung Kuo Building, No.167, Tun Hwa North Road, Taipei (105) Taiwan Tel: <886> (2) 2718-3666 Fax: <886> (2) 2718-8180 Telex: 23222 HAS-TP Hitachi Asia (Hong Kong) Ltd. Group III (Electronic Components) 7th Flr, North Tower, World Finance Centre, Harbour City, Canton Road, Tsim Sha Tsui, Kowloon, Hong Kong Tel: <852> (2) 735 9218 Fax: <852> (2) 730 0281 Telex: 40815 HITEC HX Copyright ' Hitachi, Ltd., 2000. All rights reserved. Printed in Japan. Colophon 1.0 11