HA17358/A Series - Hitachi Semiconductor

HA17358/A Series

Dual Operational Amplifier

ADE-204-033 (Z)

1st Edition

July 2000

Description

HA17358 series and HA17358A series are dual operational amplifier that provide high gain and internal

phase compensation, with single power supply. They can be widely applied to control equipments and to

general use.

Features

• Wide range of supply voltage, and single power supply used

• Wide range of common mode voltage, and possible to operate with an input about 0 V, and output

around 0 V is available

• Frequency characteristics and input bias current are temperature compensated

Features only for “A” series

• Low electro-magnetic susceptibility level

Output Offset Voltage vs. Input InterferenceMeasurement Condition

Output offset voltage (arb. unit)

5.0

4.0

3.0

2.0

1.0

−1.0

100E+3 1E+6 10E+6 100E+6 1E+9 10E+9

Input RF frequency (Hz)

HA17358A series

HA17358 series

Rs −

0.01 µ

Vin

−10 dBm

RF signal source

(for quasi-RF noise)

Vcc = +7.5 V

Vee = −7.5 V

Vout

(= 100∗Vio)

_Improve-

ment

Notice: The example of an applied circuit or combination with other equipment shown herein indicates

characteristics and performance of semiconductor -applied products.

The company shall assume no responsibility for any problem involving a patent caused when

applying the descriptions in the example.

HA17358/A Series

Ordering Information

HA17358 Series

Type No. Application Package

HA17358 Commercial use DP-8

HA17358F FP-8D

HA17358A Series

Type No. Application Package

HA17358APS Industrial use DP-8

HA17358ARP FP-8DC

HA17358AFP FP-8D

HA17358/A Series

Pin Arrangement

−+

Vout1

Vin(−)1

Vin(+)1

GND

VCC

Vout2

Vin(−)2

Vin(+)2

+−

(Top View)

Circuit Schematic (1/2)

Q1Q4

Q2Q3

Q13

Q12

Q11

Q10

Q8Q9

Vout

Vin(+)

Vin(−)C

HA17358/A Series

Absolute Maximum Ratings (Ta = 25°C)

Ratings

Item Symbol HA17358/APS HA17358F/AFP/ARP Unit

Supply voltage VCC 32 32 V

Sink current Isink 50 50 mA

Power dissipation PT570 *1385 *2mW

Common mode input voltage VCM –0.3 to VCC −0.3 to VCC V

Differential input voltage Vin (diff) ±VCC ±VCC V

Operating temperature Topr −20 to +75 −20 to +75 °C

Storage temperature Tstg −55 to +125 −55 to +125 °C

Notes: 1. This is the allowable values up to Ta = 50°C. Derate by 8.3 mW/°C.

2. This is the allowable value up to Ta = 45°C mounting on 30% wiring density glass epoxy board.

Derate by 7.14 mW/°C above that temperature.

HA17358/A Series

Electrical Characteristics (VCC = +15 V, Ta = 25°C)

Item Symbol Min Typ Max Unit Test Conditions

Input offset voltage VIO —3 7 mVV

CM = 7.5V, RS = 50Ω, Rf = 50kΩ

Input offset current IIO — 5 50 nA VCM = 7.5V, IIO = | II (+) – II (–) |

Input bias current IIB — 30 250 nA VCM = 7.5V

Power source rejection

ratio PSRR — 93 — dB RS = 1kΩ, Rf = 100kΩ

Voltage gain AVD 75 90 — dB RL = ∞, RS = 1kΩ, Rf = 100kΩ

Common mode rejection

ratio CMR — 80 — dB RS = 50Ω, Rf = 5kΩ

Common mode input

voltage range VCM (+) 13.5 — — V RS = 1kΩ, Rf = 100kΩ

VCM (–) — — –0.3 V RS = 1kΩ, Rf = 100kΩ

Peak-to-peak output

voltage Vop-p — 13.6 — V f = 100Hz, RL = 20kΩ, R

= 1kΩ,

Rf = 100kΩ

Output source current Iosource 20 40 — mA VIN+ = 1V, VIN– = 0V, VOH = 10V

Output sink current Iosink 10 20 — mA VIN– = 1V, VIN+ = 0V, VOL = 2.5V

Output sink current Iosink 15 50 — µAV

IN– = 1V, VIN+ = 0V,

Vout = 200mV

Supply current ICC — 0.8 2 mA VIN = GND, RL = ∞

Slew rate SR — 0.2 — V/µsR

L = ∞, VCM = 7.5V, f = 1.5kHz

Channel separation CS — 120 — dB f = 1kHz

HA17358/A Series

Characteristic Curves

Output Source Current vs. Ambient Temperature

Output source current Iosource (mA)

Ambeint temperature Ta (°C)

−200 20406080

VCC = 15 V

VOH = 10 V

Input Bias Current vs. Ambient Temperature

Input bias current IIB (nA)

Ambeint temperature Ta (°C)

−200 20406080

VCC = 15 V

VCM = 7.5 V

Supply Current vs. Supply Voltage

Supply current ICC (mA)

Supply voltage VCC (V)

08 16243240

Ta = 25°C80

Input bias current IIB (nA)

Supply voltage VCC (V)

08 16243240

Ta = 25°C

Voltage Gain vs. Supply Voltage

160

Voltage gain AVD (dB)

Supply voltage VCC (V)

120

08 16243240

Ta = 25°C

RL = ∞

Maxlmum Output Voltage vs. Frequency

Input Bias Current vs. Supply Voltage

Maximum output voltage VOP-P (V)

Frequency f (Hz)

1 k 3 k 10 k 30 k 100 k 300 k

VCC = 15 V

Ta = 25°C

RL = 20 kΩ

1 M

HA17358/A Series

Voltage Gain vs. Frequency

VCC = 15V

Ta = 25°C

RL = ∞

Voltage gain AVD (dB)

120

100

01 3 10 30 100 300 1 k 3 k 10 k 30 k 100 k 300 k 1 M

Frequency f (Hz)

VCC = 15V

Ta = 25°C

RS = 50 Ω

120

100

100 300 1 k 3 k 10 k 30 k 100 k 300 k 1M

Frequency f (Hz)

Common Mode Rejection Ratio vs. Frequency

Common mode rejection ratio CMR (dB)

HA17358/A Series

Solder Mounting Method

1. Small and light surface-mount packages require spicial attentions on solder mounting.

On solder mounting, pre-heating before soldering is needed.

The following figure show an example of infrared rays refow.

2. The difference of thermal expansion coefficeient between mounted substrates and IC leads may cause a

failure like solder peeling or soler wet, and electrical characteristics may change by thermal stress.

Therefore, mounting should be done after sufficient confirmation for especially in case of ceramic

substrates.

Temperature

140 to 160°C

1 to 5°C/s

235°C Max 10 s Max

1 to 4°C/s

Time (s)

≅ 60 s

Figure 1 An Example of Infrared Rays Reflow Conditions

HA17358/A Series

Package Dimensions

Hitachi Code

JEDEC

EIAJ

Mass

(reference value)

DP-8

Conforms

0.54 g

Unit: mm

9.6

10.6 Max

0.89 1.3

6.3

7.4 Max

2.54 Min

5.06 Max

2.54 ± 0.25 0.48 ± 0.10

7.62

0.25

+ 0.10

– 0.05

0° – 15°

0.1 Min

1.27 Max

Hitachi Code

JEDEC

EIAJ

Mass

(reference value)

FP-8D

—

Conforms

0.10 g

Unit: mm

*Dimension including the plating thickness

Base material dimension

0.10 ± 0.10

2.03 Max

4.4

*0.22 ± 0.05

4.85

0.75 Max

0.40 ± 0.06

0.60

+ 0.25

– 0.18

*0.42 ± 0.08

0.12

0.15

0° – 8°

1.05

5.25 Max

1.27

0.20 ± 0.04

6.50

+ 0.25

– 0.15

HA17358/A Series

Hitachi Code

JEDEC

EIAJ

Mass

(reference value)

FP-8DC

Conforms

—

0.085 g

Unit: mm

*Dimension including the plating thickness

Base material dimension

1.75 Max

4.90

0.25

0.15

0° – 8°

1.27

3.95

0.40 ± 0.06

*0.42 ± 0.08

5.3 Max

0.75 Max

0.14+ 0.11

– 0.04

0.20 ± 0.03

*0.22 ± 0.03

0.60+ 0.67

– 0.20

6.10+ 0.10

– 0.30 1.08

HA17358/A Series

Cautions

1. Hitachi neither warrants nor grants licenses of any rights of Hitachi’s or any third party’s patent,

Hitachi bears no responsibility for problems that may arise with third party’s rights, including

intellectual property rights, in connection with use of the information contained in this document.

2. Products and product specifications may be subject to change without notice. Confirm that you have

received the latest product standards or specifications before final design, purchase or use.

3. Hitachi makes every attempt to ensure that its products are of high quality and reliability. However,

contact Hitachi’s sales office before using the product in an application that demands especially high

quality and reliability or where its failure or malfunction may directly threaten human life or cause risk

of bodily injury, such as aerospace, aeronautics, nuclear power, combustion control, transportation,

traffic, safety equipment or medical equipment for life support.

4. Design your application so that the product is used within the ranges guaranteed by Hitachi particularly

for maximum rating, operating supply voltage range, heat radiation characteristics, installation

conditions and other characteristics. Hitachi bears no responsibility for failure or damage when used

beyond the guaranteed ranges. Even within the guaranteed ranges, consider normally foreseeable

failure rates or failure modes in semiconductor devices and employ systemic measures such as fail-

safes, so that the equipment incorporating Hitachi product does not cause bodily injury, fire or other

consequential damage due to operation of the Hitachi product.

5. This product is not designed to be radiation resistant.

6. No one is permitted to reproduce or duplicate, in any form, the whole or part of this document without

written approval from Hitachi.

7. Contact Hitachi’s sales office for any questions regarding this document or Hitachi semiconductor

products.

Hitachi, Ltd.

Semiconductor & Integrated Circuits.

Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan

Tel: Tokyo (03) 3270-2111 Fax: (03) 3270-5109

Hitachi Asia Ltd.

16 Collyer Quay #20-00

Hitachi Tower

Singapore 049318

Tel: 535-2100

Fax: 535-1533

URL NorthAmerica : http://semiconductor.hitachi.com/

Europe : http://www.hitachi-eu.com/hel/ecg

Asia : http://www.hitachi.com.sg/grp3/sicd

Japan : http://www.hitachi.co.jp/Sicd/indx.htm

Hitachi Asia Ltd.

Taipei Branch Office

3rd Flr, Hung Kuo Building, No.167,

Tun Hwa North Road, Taipei (105)

Taiwan

Tel: <886> (2) 2718-3666

Fax: <886> (2) 2718-8180

Telex: 23222 HAS-TP

Hitachi Asia (Hong Kong) Ltd.

Group III (Electronic Components)

7th Flr, North Tower, World Finance Centre,

Harbour City, Canton Road, Tsim Sha Tsui,

Kowloon, Hong Kong

Tel: <852> (2) 735 9218

Fax: <852> (2) 730 0281

Telex: 40815 HITEC HX

Hitachi Europe Ltd.

Electronic Components Group.

Whitebrook Park

Lower Cookham Road

Maidenhead

Berkshire SL6 8YA, United Kingdom

Tel: <44> (1628) 585000

Fax: <44> (1628) 585160

Hitachi Europe GmbH

Electronic Components Group

Dornacher Stra§e 3

D-85622 Feldkirchen, Munich

Germany

Tel: <49> (89) 9 9180-0

Fax: <49> (89) 9 29 30 00

Hitachi Semiconductor

(America) Inc.

179 East Tasman Drive,

San Jose,CA 95134

Tel: <1> (408) 433-1990

Fax: <1>(408) 433-0223

For further information write to:

Colophon 1.0