WIRE, RADIATION-CROSSLINKED, MODIFIED FLEXIBLE ETFE-INSULATED,
NORMAL WEIGHT, GENERAL PURPOSE, 600 VOLT
PART NUMBER
1/
FINISHED WIRE
CONDUCTOR
STRANDING
(number x AWG)
WIRE
SIZE
(AWG) MAXIMUM
DIAMETER OF
STRANDED
CONDUCTOR
(in.)
TITLE
SPECIFICATION CONTROL DRAWING
TABLE I. CONSTRUCTION DETAILS
MINIMUM
82A0812-26-*
82A0812-24-*
82A0812-22-*
82A0812-20-*
82A0812-18-*
82A0812-16-*
82A0812-14-*
82A0812-12-*
82A0812-10-*
82A0812-8-*
82A0812-6-*
82A0812-4-*
82A0812-2-*
82A0812-0-*
This specification sheet forms a part of the latest of Raychem Specification 80.
26
24
22
20
18
16
14
12
10
8
6
4
2
0
.021
.027
.033
.043
.053
.067
.086
.106
.140
.173
.208
.285
.345
.465
Date Revision
82A0812
CONDUCTOR - SILVER-COATED COPPER JACKET - RADIATION-CROSSLINKED,
MODIFIED FLEXIBLE ETFE
.017
.023
.029
.037
.047
.061
.078
.096
.126
.157
.192
.265
.325
.435
63 x 44
105 x 44
154 X 44
154 X 42
259 X 42
259 x 40
665 x 42
665 x 40
665 x 38
665 x 36
1045 x 36
1665 x 36
1665 x 34
2660 x 34
MAXIMUM
RESISTANCE
AT 20°C
(ohms/1000 ft)
46.9
28.2
19.2
11.7
7.14
4.62
2.96
1.89
1.12
.714
.490
.326
.204
.133
.500
.750
1.00
1.50
2.00
2.00
3.00
3.00
3.00
4.00
4.00
4.00
6.00
6.00
CROSSLINKING PROOF TEST
CROSSLINKING PROOF TEST
.375
.500
.500
.500
.750
1.00
1.00
1.50
2.00
3.00
4.00
5.00
6.00
8.00
MANDREL DIAMETER
(inch) (±3%) WEIGHT
(lb) (± 3%)
MAXIMUM
WEIGHT
(lb/1000 ft)
1.7
2.5
3.7
5.2
8.0
11.9
19.3
27.9
50.0
77.3
118.
190.
282.
442.
.038 ± .003
.044 ± .003
.054 ± .003
.064 ± .004
.076 ± .004
.092 ± .005
.116 ± .005
.137 ± .006
.187 ± .008
.230 ± .008
.277 ± .010
.359 ± .010
.433 ± .016
.558 ± .016
DIAMETER
(in.)
PRIMARY INSULATION - RADIATION-CROSSLINKED,
MODIFIED FLEXIBLE ETFE
COLOR - LIGHT GREEN
PART NUMBER
1/
82A0812-26-*
82A0812-24-*
82A0812-22-*
82A0812-20-*
82A0812-18-*
82A0812-16-*
82A0812-14-*
82A0812-12-*
82A0812-10-*
82A0812-8-*
82A0812-6-*
82A0812-4-*
82A0812-2-*
82A0812-0-*
BEND TESTING
TABLE II. PERFORMANCE DETAILS
4-10-06 H
DIMENSIONS ARE IN INCHES, AND UNLESS OTHERWISE DESIGNATED ARE NOMINAL.
Page 1 of 2
R Wire & Cable
501 Oakside Avenue
Redwood City, CA 94063-3800
Phone: 1-800-227-8816
Fax: 1-650-361-6297
THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN.
REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID.
1/ COLORS AND COLOR CODE DESIGNATORS SHALL BE IN ACCORDANCE WITH MIL-STD-681. OTHER CODES
AND SUFFIXES MAY BE ADDED TO THE PART NUMBER, AS NECESSARY, TO CAPTURE ANY ADDITIONAL
REQUIREMENTS IMPOSED BY THE PURCHASE ORDER.
Tyco Electronics also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer.
Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice.
© 2006 Tyco Electronics Corporation. All rights reserved.
SCD Number
Page 2 of 2 82A0812
TEMPERATURE RATING: 150°C
Maximum continuous conductor temperature
VOLTAGE RATING: 600 volts (rms) at sea level
CONCENTRICITY: 70% (minimum)
CROSSLINKING PROOF TEST: 300 ± 3°C,
30 minutes for AWG 26 - 14, 1 hour for AWG 12 and larger
IDENTIFICATION AND COLOR STRIPING DURABILITY:
125 cycles (250 strokes) (minimum), 500 g weight
INSULATION ELONGATION AND TENSILE STRENGTH:
AWG 26, Elongation, 75% (minimum)
Tensile Strength, 3000 lbf/in2 (minimum)
AWG 24 -10, Elongation, 75% (minimum)
Tensile Strength, 3500 lbf/in2 (minimum)
AWG 8 - 0, Elongation, 125% (minimum)
Tensile Strength, 3000 lbf/in² (minimum)
INSULATION FLAWS:
Primary Insulation,
Spark Test, 1.5 kV (rms) at 3 kHz
Impulse Dielectric Test, 6.0 kV (peak)
Finished Wire,
Spark Test, 3.0 kV (rms) at 3 kHz
Impulse Dielectric Test, 8.0 kV (peak)
INSULATION THICKNESS:
For AWG 26 - 18, .004 inch (minimum) for primary insulation
.004 inch (minimum) for outer jacket
For AWG 16 - 10, .005 inch (minimum) for primary insulation
.005 inch (minimum) for outer jacket
For AWG 8 - 4, .008 inch (minimum) for primary insulation
.012 inch (minimum) for outer jacket
For AWG 2 - 0, .010 inch (minimum) for primary insulation
.015 inch (minimum) for outer jacket
JACKET COLOR: White preferred
PRODUCT IDENTIFICATION: AWG 26 - 10, black ink only
AWG 8 and larger, black ink preferred
SECANT MODULUS: (Test per ASTM D 882)
AWG 26 - 10: 5.0 x 104 lbf/in2 (maximum)
AWG 8 and larger: 4.0 x 104 lbf/in2 (maximum)
2% strain, 2 inch jaw separation, 0.2 inch/minute
SHRINKAGE: 150 ± 3°C for 6 hours,
AWG 26 -10, 0.13 inch (maximum) in 12 inches
AWG 8 - 0, 0.25 inch (maximum) in 12 inches
VOLTAGE WITHSTAND TEST (Post Environmental): 2500 volts (rms), 60 Hz
PART NUMBER:
The "*" in the part numbers on page 1 shall be replaced by color code designators.
1/ Example: AWG 16, white wire: 82A0812-16-9
AWG 16, white with blue stripe: 82A0812-16-96
1/ See footer section on page 1
WIRE RATINGS AND ADDITIONAL REQUIREMENTS
Revision
H
SPECIFICATION CONTROL DRAWING
