19-3166; Rev 0; 1/04 3.5- and 4.5-Digit, Single-Chip ADCs with LED Drivers The MAX1447/MAX1496/MAX1498 low-power, 3.5- and 4.5-digit, analog-to-digital converters (ADCs) with integrated light-emitting diode (LED) drivers operate from a single 2.7V to 5.25V power supply. They include an internal reference, a high-accuracy on-chip oscillator, and a multiplexed LED display driver. An internal charge pump generates the negative supply needed to power the integrated input buffers for single-supply operation. The ADC is configurable for either a 2V or 200mV input range and it outputs its conversion results to an LED. The MAX1496 is a 3.5-digit (1999 count) device and the MAX1447/MAX1498 are 4.5-digit (19,999 count) devices. The MAX1447/MAX1496/MAX1498 do not require external precision integrating capacitors, autozero capacitors, crystal oscillators, charge pumps, or other circuitry required with dual-slope ADCs (commonly used in panel meter circuits). These devices also feature on-chip buffers for the differential signal and reference input, allowing direct interface with high-impedance signal sources. In addition, they use continuous internal offset-calibration and offer >100dB rejection of 50Hz and 60Hz line noise. Other features include data hold and peak detection and overrange/underrange detection. The MAX1447 features on-demand enhanced offset calibration for improved offset performance. The MAX1447/MAX1498 are available in a 32-pin, 7mm 7mm TQFP package and the MAX1496 is available in 28-pin SSOP and 28-pin PDIP packages. All devices in this family operate over the -40C to +85C extended temperature range. Features High Resolution MAX1447/MAX1498: 4.5 Digits (19,999 Count) MAX1496: 3.5 Digits (1999 Count) Sigma-Delta ADC Architecture No Integrating Capacitors Required No Autozeroing Capacitors Required >100dB of Simultaneous 50Hz and 60Hz Rejection Selectable Input Range of 200mV or 2V Selectable Voltage Reference: Internal 2.048V or External Internal High-Accuracy Oscillator Needs No External Components Automatic Offset Calibration On-Demand Enhanced Offset Calibration (MAX1447) Operate from a Single 2.7V to 5.25V Supply Low Power (Exclude LED-Driver Current) Maximum 744A Operating Current (MAX1496) Maximum 960A Operating Current (MAX1447/MAX1498) Maximum 325A Shutdown Current Multiplexed Common-Cathode LED Drivers Resistor-Programmable Segment Current Small 32-Pin, 7mm x 7mm TQFP Package (4.5 Digits), 28-Pin SSOP Package (3.5 Digits) Also Available in a PDIP Package (3.5 Digits) Applications Ordering Information Digital Panel Meters PART Digital Voltmeters MAX1447ECJ -40C to +85C 32 TQFP 4.5 Digital Multimeters MAX1496EAI* -40C to +85C 28 SSOP 3.5 MAX1496EPI -40C to +85C 28 PDIP 3.5 MAX1498ECJ -40C to +85C 32 TQFP 4.5 Pin Configurations appear at end of data sheet. TEMP RANGE PINRESOLUTION PACKAGE (DIGITS) Hand-Held Meters *Future product--contact factory for availability. ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim's website at www.maxim-ic.com. 1 MAX1447/MAX1496/MAX1498 General Description MAX1447/MAX1496/MAX1498 3.5- and 4.5-Digit, Single-Chip ADCs with LED Drivers ABSOLUTE MAXIMUM RATINGS VLED to GLED ..........................................................-0.3V to +6V GLED to GND ........................................................-0.3V to +0.3V SEG_ to GLED..........................................-0.3V to (VLED + 0.3V) DIG_ to GLED ..........................................-0.3V to (VLED + 0.3V) DIG_ Sink Current .............................................................300mA DIG_ Source Current...........................................................50mA SEG_ Sink Current ..............................................................50mA SEG_ Source Current..........................................................50mA Maximum Current Input into Any Other Pin ........................50mA Continuous Power Dissipation (TA = +70C) 32-Pin TQFP (derate 20.7mW/C above +70C).....1652.9mW 28-Pin SSOP (derate 9.5mW/C above +70C) ...........762mW 28-Pin PDIP (derate 14.3mW/C above +70C)......1142.9mW Operating Temperature Range ...........................-40C to +85C Junction Temperature ......................................................+150C Storage Temperature Range .............................-60C to +150C Lead Temperature (soldering, 10s) .................................+300C AVDD to GND (MAX1447/MAX1498) ........................-0.3V to +6V DVDD to GND (MAX1447/MAX1498)........................-0.3V to +6V AIN+, AIN- to GND (MAX1447/MAX1498) ......................VNEG to (AVDD to +0.3V) REF+, REF- to GND (MAX1447/MAX1498) ..................... VNEG to (AVDD to +0.3V) INTREF, RANGE, DPSET1, DPSET2, HOLD, PEAK, DPON to GND (MAX1447/MAX1498) ..-0.3V to (DVDD + 0.3V) VNEG to GND (MAX1447/MAX1498).......-2.6V to (AVDD + 0.3V) LED_EN to GND (MAX1447/MAX1498) ...-0.3V to (DVDD + 0.3V) ISET to GND (MAX1447/MAX1498) .........-0.3V to (AVDD + 0.3V) VDD to GND (MAX1496) ...........................................-0.3V to +6V AIN+, AIN- to GND (MAX1496)..............VNEG to (VDD to +0.3V) REF+, REF- to GND (MAX1496) ........... VNEG to (VDD to +0.3V) INTREF, RANGE, DPSET1, DPSET2, HOLD, PEAK, DPON to GND (MAX1496) .....................-0.3V to (VDD + 0.3V) VNEG to GND (MAX1496)..........................-2.6V to (VDD + 0.3V) ISET to GND (MAX1496) ............................-0.3V to (VDD + 0.3V) Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (AVDD = DVDD = VDD = +2.7V to +5.25V, GND = 0, VLED = +2.7V to +5.25V, GLED = 0, VREF+ - VREF- = 2.048V (external reference), CREF+ = CREF- = 0.1F, CVNEG = 0.1F. Internal clock mode, unless otherwise noted. All specifications are at TA = TMIN to TMAX. Typical values are at TA = +25C, unless otherwise noted.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS DC ACCURACY MAX1447/MAX1498 Noise-Free Resolution Integral Nonlinearity (Note 1) MAX1496 INL -19,999 +19,999 -1999 +1999 2.000V range 1 200mV range 1 Range Change Ratio (VAIN+ - VAIN- = 0.100V) on 200mV range (VAIN+ - VAIN- = 0.100V) on 2.0V range Rollover Error VAIN+ - VAIN- = full scale VAIN- - VAIN+ = full scale Output Noise Offset Error (Zero Input Reading) VIN = 0 (Note 2) Gain Error (Note 3) Offset Drift (Zero Reading Drift) VIN = 0 (Note 4) Gain Drift Counts 10:1 Ratio 1 Counts 10 Offset Counts -0 -0.5 VP-P 0 Readings +0.5 % FSR 0.1 V/C 1 ppm/C 5 Hz INPUT CONVERSION RATE Conversion Rate 2 _______________________________________________________________________________________ 3.5- and 4.5-Digit, Single-Chip ADCs with LED Drivers (AVDD = DVDD = VDD = +2.7V to +5.25V, GND = 0, VLED = +2.7V to +5.25V, GLED = 0, VREF+ - VREF- = 2.048V (external reference), CREF+ = CREF- = 0.1F, CVNEG = 0.1F. Internal clock mode, unless otherwise noted. All specifications are at TA = TMIN to TMAX. Typical values are at TA = +25C, unless otherwise noted.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS ANALOG INPUTS (AIN+, AIN-) (bypass to GND with 0.1F or greater capacitors) AIN Input Voltage Range (Note 5) RANGE = GND -2.0 +2.0 RANGE = DVDD (MAX1447/MAX1498) or VDD (MAX1496) -0.2 +0.2 -2.2 +2.2 AIN Absolute Input Voltage Range to GND Normal-Mode 50Hz and 60Hz Rejection (Simultaneously) V V 50Hz and 60Hz 2% 100 dB Common-Mode 50Hz and 60Hz Rejection (Simultaneously) CMR For 50Hz and 60Hz 2%, RSOURCE < 10k 150 dB Common-Mode Rejection CMR At DC 100 dB 10 nA Input Leakage Current Input Capacitance 10 Average Dynamic Input Current (Note 6) -20 pF +20 nA INTERNAL REFERENCE (REF- = GND, INTREF = DVDD (MAX1447/MAX1498) or VDD (MAX1496) (bypass REF+ to GND with a 4.7F capacitor) REF Output Voltage VREF 2.007 REF Output Short-Circuit Current REF Output Temperature Coefficient TCVREF Load Regulation ISOURCE = 0 to 300A, ISINK = 0 to 30A Line Regulation Noise Voltage 2.048 2.089 V 1 mA 40 ppm/C 6 mV/A 50 V/V 0.1Hz to 10Hz 25 10Hz to 10kHz 400 VP-P EXTERNAL REFERENCE (INTREF = GND) (bypass REF+ and REF- to GND with 0.1F or greater capacitors) REF Input Voltage Differential, VREF+ - VREF- Absolute REF+, REF- Input Voltage to GND 2.048 -2.2 Normal-Mode 50Hz and 60Hz Rejection (Simultaneously) V +2.2 V 50Hz and 60Hz 2% 100 dB Common-Mode 50Hz and 60Hz Rejection (Simultaneously) CMR For 50Hz and 60Hz 2%, RSOURCE < 10k 150 dB Common-Mode Rejection CMR At DC 100 dB 10 nA Input Leakage Current Input Capacitance 10 Average Dynamic Input Current (Note 6) -20 pF +20 nA _______________________________________________________________________________________ 3 MAX1447/MAX1496/MAX1498 ELECTRICAL CHARACTERISTICS (continued) MAX1447/MAX1496/MAX1498 3.5- and 4.5-Digit, Single-Chip ADCs with LED Drivers ELECTRICAL CHARACTERISTICS (continued) (AVDD = DVDD = VDD = +2.7V to +5.25V, GND = 0, VLED = +2.7V to +5.25V, GLED = 0, VREF+ - VREF- = 2.048V (external reference), CREF+ = CREF- = 0.1F, CVNEG = 0.1F. Internal clock mode, unless otherwise noted. All specifications are at TA = TMIN to TMAX. Typical values are at TA = +25C, unless otherwise noted.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS -2.60 -2.42 -2.30 V +10 A CHARGE PUMP Output Voltage VNEG CVNEG = 0.1F to GND DIGITAL INPUTS (INTREF, RANGE, PEAK, HOLD, DPSET1, DPSET2, DPON) Input Current Input Low Voltage Input High Voltage Input Hysteresis IIN VIN = 0 or DVDD = VDD -10 MAX1447/MAX1498 0.3 x DVDD MAX1496 0.3 x VDD VINL MAX1447/MAX1498 0.7 x DVDD MAX1496 0.7 x VDD VINH VHYS V V 200 mV POWER SUPPLY (Note 7) VDD Voltage MAX1496 2.70 5.25 V AVDD Voltage AVDD MAX1447/MAX1498 2.70 5.25 V DVDD Voltage DVDD MAX1447/MAX1498 2.70 Power-Supply Rejection VDD PSRR (Note 8) 80 dB Power-Supply Rejection AVDD PSRRA (Note 8) 80 dB Power-Supply Rejection DVDD PSRRD (Note 8) 100 VDD = 5.25V 664 744 VDD = 3.3V 618 663 Standby mode 268 MAX1496 VDD Current (Note 9) MAX1447/MAX1498 AVDD Current (Note 9) MAX1447/MAX1498 DVDD Current (Note 9) VDD IVDD IAVDD IDVDD 5.25 4 dB 640 AVDD = 3.3V 600 Standby mode 305 DVDD = 5.25V 320 DVDD = 3.3V 180 From AVDD or VDD A 325 AVDD = 5.25V Standby mode LED Drivers Bias Current V A A 20 120 _______________________________________________________________________________________ A 3.5- and 4.5-Digit, Single-Chip ADCs with LED Drivers (AVDD = DVDD = VDD = +2.7V to +5.25V, GND = 0, VLED = +2.7V to +5.25V, GLED = 0, VREF+ - VREF- = 2.048V (external reference), CREF+ = CREF- = 0.1F, CVNEG = 0.1F. Internal clock mode, unless otherwise noted. All specifications are at TA = TMIN to TMAX. Typical values are at TA = +25C, unless otherwise noted.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS LED DRIVERS (Table 5) LED Supply Voltage VLED LED Shutdown Supply Current ISHDN LED Supply Current ILED Display Scan Rate fOSC Segment Current Slew Rate Seven segments and decimal point on, RISET = 25k 176 MAX1447/MAX1498 512 MAX1496 640 ISEG/t DIG_ Voltage Low VDIG Segment Drive Source Current Matching ISEG Segment Drive Source Current ISEG Interdigit Blanking Time 2.70 LED driver shutdown mode 5.25 V 10 A 180 mA Hz 25 IDIG_ = 176mA VLED - VSEG = 0.6V, RISET = 25k 16.0 mA/s 0.178 0.300 V 3 10 % 21.5 25.5 mA 4 s Note 1: Integral nonlinearity is the deviation of the analog value at any code from its theoretical value after nulling the gain error and offset error. Note 2: Offset calibrated. Note 3: Offset nulled. Note 4: Drift error is eliminated by recalibration at the new temperature. Note 5: The input voltage range for the analog inputs is given with respect to the voltage on the negative input of the differential pair. Note 6: VAIN+ or VAIN- = -2.2V to +2.2V. VREF+ or VREF- = -2.2V to +2.2V. All input structures are identical. Production tested on AIN+ and REF+ only. Note 7: Power-supply currents are measured with all digital inputs at either GND or DVDD. Note 8: Measured at DC by changing the power-supply voltage from 2.7V to 5.25V and measuring the effect on the conversion error with external reference. PSRR at 50Hz and 60Hz exceeds 120dB with filter notches at 50Hz and 60Hz (Figure 2). Note 9: LED drivers are disabled. _______________________________________________________________________________________ 5 MAX1447/MAX1496/MAX1498 ELECTRICAL CHARACTERISTICS (continued) Typical Operating Characteristics (AVDD = DVDD = VDD = VLED = +2.7V to +5.25V, GND = 0, GLED = 0, external reference mode, REF+ = 2.048V, REF- = GND, RANGE = 1, internal clock mode, TA = +25C, unless otherwise noted.) 300 DIGITAL SUPPLY 500 450 100 3.25 3.75 4.25 4.75 MAX1447/96/98 toc03 DIGITAL SUPPLY 200 3.21 3.72 4.23 4.74 5.25 10 0 20 30 40 50 60 SUPPLY VOLTAGE (V) TEMPERATURE (C) SUPPLY CURRENT vs. TEMPERATURE (MAX1496) SHUTDOWN CURRENT vs. TEMPERATURE (MAX1447/MAX1498) SHUTDOWN CURRENT vs. TEMPERATURE (MAX1496) 680 670 660 650 640 630 300 ANALOG SUPPLY 250 620 200 150 100 300 50 600 10 35 60 85 200 150 100 0 0 -15 250 50 DIGITAL SUPPLY 610 70 350 SHUTDOWN CURRENT (A) MAX1447/96/98 toc04 690 0 10 20 30 40 50 60 -40 70 -15 10 35 60 85 TEMPERATURE (C) TEMPERATURE (C) TEMPERATURE (C) SHUTDOWN CURRENT vs. SUPPLY VOLTAGE (MAX1447/MAX1498) SHUTDOWN CURRENT vs. SUPPLY VOLTAGE (MAX1496) OFFSET ERROR vs. SUPPLY VOLTAGE (MAX1447/MAX1498) 150 100 50 250 200 150 100 50 DIGITAL SUPPLY 2.75 3.25 3.75 4.25 SUPPLY VOLTAGE (V) 4.75 5.25 0.14 0.09 0.04 -0.01 -0.06 -0.11 0 0 MAX1447/96/98 toc09 300 0.19 OFFSET ERROR (LSB) 200 MAX1447/96/98 toc08 ANALOG SUPPLY 350 SHUTDOWN CURRENT (A) 250 MAX1447/96/98 toc07 300 6 300 SUPPLY VOLTAGE (V) 700 -40 400 0 2.70 5.25 SHUTDOWN CURRENT (A) 2.75 ANALOG SUPPLY 500 100 400 0 SUPPLY CURRENT (A) 550 600 MAX1447/96/98 toc06 200 600 700 SUPPLY CURRENT (A) 400 MAX1447/96/98 toc02 ANALOG SUPPLY 500 650 MAX1447/96/98 toc05 SUPPLY CURRENT (A) 600 700 SUPPLY CURRENT (A) MAX1447/96/98 toc01 700 SUPPLY CURRENT vs. TEMPERATURE (MAX1447/MAX1498) SUPPLY CURRENT vs. SUPPLY VOLTAGE (MAX1496) SUPPLY CURRENT vs. SUPPLY VOLTAGE (MAX1447/MAX1498) SHUTDOWN CURRENT (A) MAX1447/MAX1496/MAX1498 3.5- and 4.5-Digit, Single-Chip ADCs with LED Drivers -0.16 2.70 3.21 3.72 4.23 SUPPLY VOLTAGE (V) 4.74 5.25 2.75 3.25 3.75 4.25 SUPPLY VOLTAGE (V) _______________________________________________________________________________________ 4.75 5.25 3.5- and 4.5-Digit, Single-Chip ADCs with LED Drivers OFFSET ERROR vs. TEMPERATURE (MAX1447/MAX1498) 0 -0.04 -0.06 -0.08 -0.2 -0.10 10 20 30 40 50 60 70 2.75 3.25 3.75 4.25 4.75 5.25 SUPPLY VOLTAGE (V) (200mV INPUT RANGE) INL vs. OUTPUT CODE (MAX1447/MAX1498) (2V INPUT RANGE) INL vs. OUTPUT CODE (MAX1447/MAX1498) MAX1447/96/98 toc14 0.5 INL (COUNTS) 0 0 -0.5 -0.5 -1.0 -20,000 -10,000 0 10,000 MAX1447/96/98 toc12 -0.05 -0.06 -0.07 -0.08 -0.10 0 10 20 30 40 50 20 15 10 0 -10,000 0 10,000 20,000 -0.2 -0.1 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 OUTPUT CODE NOISE COUNTS INTERNAL REFERENCE VOLTAGE vs. TEMPERATURE INTERNAL REFERENCE VOLTAGE vs. ANALOG SUPPLY VOLTAGE DATA OUTPUT RATE vs. TEMPERATURE 2.050 2.049 2.048 2.047 2.046 2.048 2.047 2.046 MAX1447/96/98 toc18 2.051 2.049 5.10 5.08 DATA OUTPUT RATE (Hz) 2.052 2.050 REFERENCE VOLTAGE (V) MAX1447/96/98 toc16 2.053 70 NOISE DISTRIBUTION 25 OUTPUT CODE 2.054 60 5 -1.0 -20,000 20,000 -0.04 TEMPERATURE (C) 1.0 MAX1447/96/98 toc13 0.5 -0.03 -0.09 TEMPERATURE (C) 1.0 INL (COUNTS) -0.02 -0.1 0 REFERENCE VOLTAGE (V) 0 -0.02 MAX1447/96/98 toc15 0.1 0.02 GAIN ERROR (% FULL SCALE) 0.2 0.04 0 -0.01 PERCENTAGE OF UNITS (%) 0.3 0.06 MAX1447/96/98 toc17 OFFSET ERROR (LSB) 0.4 0.08 GAIN ERROR vs. TEMPERATURE (MAX1447/MAX1498) MAX1447/96/98 toc11 0.5 GAIN ERROR (% FULL SCALE) MAX1447/96/98 toc10 0.6 GAIN ERROR vs. SUPPLY VOLTAGE (MAX1447/MAX1498) 5.06 5.04 5.02 5.00 4.98 4.96 4.94 2.045 4.92 2.045 2.044 2.044 0 10 20 30 40 50 TEMPERATURE (C) 60 70 4.90 2.75 3.25 3.75 4.25 SUPPLY VOLTAGE (V) 4.75 5.25 -40 -15 10 35 60 85 TEMPERATURE (C) _______________________________________________________________________________________ 7 MAX1447/MAX1496/MAX1498 Typical Operating Characteristics (continued) (AVDD = DVDD = VDD = VLED = +2.7V to +5.25V, GND = 0, GLED = 0, external reference mode, REF+ = 2.048V, REF- = GND, RANGE = 1, internal clock mode, TA = +25C, unless otherwise noted.) Typical Operating Characteristics (continued) (AVDD = DVDD = VDD = VLED = +2.7V to +5.25V, GND = 0, GLED = 0, external reference mode, REF+ = 2.048V, REF- = GND, RANGE = 1, internal clock mode, TA = +25C, unless otherwise noted.) OFFSET ERROR vs. COMMON-MODE VOLTAGE 5.010 5.005 5.000 4.995 4.990 0.15 0.10 0 -0.15 4.74 -2.0 -1.5 -1.0 -0.5 5.25 SUPPLY VOLTAGE (V) 0 0.5 1.0 1.5 2.0 CHARGE-PUMP OUTPUT VOLTAGE vs. ANALOG SUPPLY VOLTAGE SEGMENT CURRENT vs. SUPPLY VOLTAGE VNEG VOLTAGE (V) -2.42 -2.44 -2.46 -2.48 30 RISET = 25k 25 SEGMENT CURRENT (A) MAX1447/96/98 toc22 -2.40 20 15 10 5 0 -2.50 2.75 3.25 3.75 4.25 SUPPLY VOLTAGE (V) 8 20ms/div COMMON-MODE VOLTAGE (V) MAX1447/96/98 toc23 4.23 VNEG -0.10 -0.20 3.72 1V/div -0.05 4.980 3.21 VDD 2V/div 0.05 4.985 2.70 MAX1447/96/98 toc20 5.015 VNEG STARTUP SCOPE SHOT 0.20 OFFSET ERROR COUNTS MAX1447/96/98 toc19 5.020 MAX1447/96/98 toc21 DATA OUTPUT RATE vs. SUPPLY VOLTAGE DATA OUTPUT RATE (Hz) MAX1447/MAX1496/MAX1498 3.5- and 4.5-Digit, Single-Chip ADCs with LED Drivers 4.75 5.25 2.70 3.21 3.72 4.23 4.74 SUPPLY VOLTAGE (V) _______________________________________________________________________________________ 5.25 3.5- and 4.5-Digit, Single-Chip ADCs with LED Drivers PIN FUNCTION MAX1496 MAX1447/ MAX1498 NAME 1 31 VNEG -2.5V Charge-Pump Voltage Output. Connect a 0.1F capacitor to GND. 2 32 REF- Negative Reference Voltage Input. For internal-reference operation, connect REF- to GND. For external-reference operation, bypass REF- to GND with a 0.1F capacitor and set VREFfrom -2.2V to +2.2V, provided VREF+ > VREF-. 3 1 REF+ Positive Reference Voltage Input. For internal-reference operation, connect a 4.7F capacitor from REF+ to GND. For external-reference operation, bypass REF+ to GND with a 0.1F capacitor and set VREF+ from -2.2V to +2.2V, provided VREF+ > VREF-. 4 2 AIN+ Positive Analog Input. Positive side of fully differential analog input. Bypass AIN+ to GND with a 0.1F or greater capacitor. 5 3 AIN- Negative Analog Input. Negative side of fully differential analog input. Bypass AIN- to GND with a 0.1F or greater capacitor. 6 4 ISET Segment Current Controller. Connect to ground through a resistor to set the segment current. See Table 5 for current selection. 7 5 GND Ground 8 -- VDD Analog and Digital Circuit Supply Voltage. Connect VDD to a +2.7V to +5.25V power supply. Bypass VDD to GND with a 0.1F capacitor and a 4.7F capacitor. 9 8 INTREF Internal-Reference Logic Input. Connect to GND to select external-reference mode. Connect to DVDD for the MAX1447/MAX1498 and VDD for the MAX1496 to select the internalreference mode. 10 9 RANGE Range Logic Input. RANGE controls the fully differential analog input range. Connect to GND for the 2V input range. Connect to DVDD (MAX1447/MAX1498) or VDD (MAX1496) for the 200mV input range. 11 10 DPSET1 Decimal-Point Logic-Input 1. Controls the decimal point of the LED. See the Decimal-Point Control section. 12 11 DPSET2 Decimal-Point Logic-Input 2. Controls the decimal point of the LED. See the Decimal-Point Control section. 13 12 PEAK Peak Logic Input. Connect to DVDD (MAX1447/MAX1498) or VDD (MAX1496) to display the highest ADC value on the LED. Connect to GND to disable the peak function. 14 13 HOLD Hold Logic Input. Connect to DVDD (MAX1447/MAX1498) or VDD (MAX1496) to hold the current ADC value on the LED. Connect to GND to update the LED at a rate of 2.5Hz and disable the hold function. For the MAX1447, only placing the device into hold mode initiates an offset mismatch calibration. Assert HOLD high for a minimum of 2s to ensure the completion of offset mismatch calibration. 15 14 DIG0 Digit 0 Driver 16 15 DIG1 Digit 1 Driver 17 16 GLED Ground for LED Display Digit Driver 18 17 DIG2 Digit 2 Driver _______________________________________________________________________________________ 9 MAX1447/MAX1496/MAX1498 Pin Description MAX1447/MAX1496/MAX1498 3.5- and 4.5-Digit, Single-Chip ADCs with LED Drivers Pin Description (continued) PIN FUNCTION NAME MAX1496 MAX1447/ MAX1498 19 18 DIG3 Digit 3 Driver 20 20 SEGA Segment A Driver 21 21 SEGB Segment B Driver 22 22 SEGC Segment C Driver 23 23 SEGD Segment D Driver 24 24 SEGE Segment E Driver 25 25 VLED LED Display Segment Driver Supply. Connect to a +2.7V to +5.25V supply. Bypass with a 0.1F capacitor to GLED. 26 26 SEGF Segment F Driver 27 27 SEGG Segment G Driver 28 28 SEGDP Segment DP Driver -- 6 AVDD Analog Positive Supply Voltage. Connect AVDD to a +2.7V to +5.25V power supply. Bypass AVDD to GND with a 0.1F capacitor. -- 7 DVDD Digital Positive Supply Voltage. Connect DVDD to a +2.7V to +5.25V power supply. Bypass DVDD to GND with a 0.1F capacitor. -- 19 DIG4 Digit 4 Driver -- 29 LED_EN -- 30 DPON Active-High LED Enable. The MAX1447/MAX1498 display driver turns off when the LED_EN is driven to logic low. The MAX1447/MAX1498 LED display driver turns on when LED_EN is driven to logic high. Decimal-Point Enable Input. Controls the decimal point of the LED. See the Decimal-Point Control section. Connect to DVDD (MAX1447/MAX1498) or VDD (MAX1496) to enable the decimal point. Detailed Description The MAX1447/MAX1496/MAX1498 low-power, highly integrated ADCs with LED drivers convert a 2V differential input voltage (one count is equal to 100V for the MAX1447/MAX1498 and 1mV for the MAX1496) with a sigma-delta ADC and output the result to an LED. An additional 200mV input range (one count is equal to 10V for the MAX1447/MAX1498 and 100V for the MAX1496) is available to measure small signals with increased resolution. The devices operate from a single 2.7V to 5.25V power supply and offer 3.5-digit (MAX1496) or 4.5-digit (MAX1447/MAX1498) conversion results. An internal 2.048V reference, internal charge pump, and a high-accuracy on-chip oscillator eliminate external components. The devices also feature on-chip buffers for the differential input signal and external-reference inputs, allowing 10 direct interface with high-impedance signal sources. In addition, they use continuous internal offset-calibration and offer >100dB of 50Hz and 60Hz line-noise rejection. Other features include data hold and peak detection and overrange/underrange detection. Analog Input Protection Internal protection diodes limit the analog input range from VNEG to (AV DD + 0.3V) for the MAX1447/ MAX1498, and from VNEG to (V DD + 0.3V) for the MAX1496. If the analog input exceeds this range, limit the input current to 10mA. Internal Analog Input/Reference Buffers The MAX1447/MAX1496/MAX1498 analog input/reference buffers allow the use of high-impedance signal sources. The input buffers' common-mode input range allows the analog inputs and the reference to range from -2.2V to +2.2V. ______________________________________________________________________________________ 3.5- and 4.5-Digit, Single-Chip ADCs with LED Drivers MAX1447/MAX1496/MAX1498 AVDD ISET VLED DVDD TIMING +2.5V SEG1 AIN+ LED DRIVER BINARY-TOBCD CONVERTERS ADC AIN- SEGF SEGDP DIG0 DIG4 INPUT BUFFERS LED_EN REF+ GLED OSCILLATOR CLOCK REF- CLK DPON -2.5V +2.5V -2.5V DPSET1 2.048V BANDGAP REFERENCE A = 1.22 DPSET2 CHARGE PUMP RANGE MAX1447 MAX1498 PEAK HOLD GND VNEG Figure 1. MAX1447/MAX1498 Functional Diagram Modulator The MAX1447/MAX1496/MAX1498 perform analog-todigital conversions using a single-bit, 3rd-order, sigmadelta modulator. The sigma-delta modulator converts the input signal into a digital pulse train whose average duty cycle represents the digitized signal information. The modulator quantizes the input signal at a much higher sample rate than the bandwidth of the input. The MAX1447/MAX1496/MAX1498 modulator provides 3rd-order frequency shaping of the quantization noise resulting from the single-bit quantizer. The modulator is fully differential for maximum signal-to-noise ratio and minimum susceptibility to power-supply noise. A singlebit data stream is then presented to the digital filter to remove the frequency-shaped quantization noise. Digital Filtering The MAX1447/MAX1496/MAX1498 contain an on-chip digital lowpass filter that processes the data stream from the modulator using a SINC4 response: sin(x) 4 x The SINC4 filter has a settling time of four output data periods (4 x 200ms). The MAX1447/MAX1496/MAX1498 have 25% overrange capability built into the modulator and digital filter. The digital filter is optimized for the fCLK equal to 4.9152MHz. The frequency response of the SINC4 filter is calculated as follows: 1 (1 - Z -N ) 4 H(z) = N (1 - Z -1) 4 f sin N fm 1 H(f) = N f sin fm where N is the oversampling ratio, and fm = N x output data rate = 5Hz. ______________________________________________________________________________________ 11 0 A -40 A B F C E DP G DIGIT 4 -80 A G F D GAIN (dB) MAX1447/MAX1496/MAX1498 3.5- and 4.5-Digit, Single-Chip ADCs with LED Drivers B F C E DP A G B F C E DP A G B F C E DP G B C DP D D D D DIGIT 3 DIGIT 2 DIGIT 1 DIGIT 0 -120 Figure 3. Segment Connection for the MAX1447/MAX1498 (4.5 Digits) -160 -200 0 10 20 30 40 50 60 FREQUENCY (Hz) A Figure 2. Frequency Response of the SINC4 Filter (Notch at 50Hz and 60Hz) Filter Characteristics Figure 2 shows the filter frequency response. The SINC4 characteristic -3dB cutoff frequency is 0.228 times the first notch frequency (5Hz). The oversampling ratio (OSR) for the MAX1496 is 128 and the OSR for the MAX1447/MAX1498 is 1024. The output data rate for the digital filter corresponds to the positioning of the first notch of the filter's frequency response. The notches of the SINC4 filter are repeated at multiples of the first notch frequency. The SINC4 filter provides an attenuation of better than 100dB at these notches. For example, 50Hz is equal to 10 times the first notch frequency and 60Hz is equal to 12 times the first notch frequency. For large step changes at the input, allow a settling time of 800ms before valid data is read. Internal Clock The MAX1447/MAX1496/MAX1498 contain an internal oscillator. Using the internal oscillator saves board space by removing the need for an external clock source. The oscillator is optimized to give 50Hz and 60Hz power-supply and common-mode rejection. Charge Pump The MAX1447/MAX1496/MAX1498 contain an internal charge pump to provide the negative supply voltage for the internal analog input/reference buffers. 12 A B F C E DP F D G DIGIT 3 G A B F C E DP G A B F C E DP G B C DP D D D DIGIT 2 DIGIT 1 DIGIT 0 Figure 4. Segment Connection for the MAX1496 (3.5 Digits) Table 1. LED Priority Table HOLD PEAK 1 X Hold value DISPLAY VALUES FORM 0 1 Peak value 0 0 Latest ADC result X = Don't care. The bipolar input range of the analog input/reference buffers allows this device to accept negative inputs with high source impedances. Connect a 0.1F capacitor from VNEG to GND. LED Driver The MAX1447/MAX1498 have a 4.5-digit common-cathode display driver, and the MAX1496 has a 3.5-digit common-cathode display driver. Figures 3 and 4 show the connection schemes for a standard seven-segment LED display. The LED update rate is 2.5Hz. The MAX1447/MAX1496/MAX1498 automatically display the results of the ADC, if desired (Table 1). ______________________________________________________________________________________ 3.5- and 4.5-Digit, Single-Chip ADCs with LED Drivers SEGG SEGF SEGE SEGD SEGC SEGB SEGA A B C D E F G DP A B C DIGIT 1 D G G DP A F B C E F DIGIT 2 A F E B G C E DP DP D D TON = T 1.95312ms = = 390.60s (MAX1447 / MAX1498) 5 5 TON = T 1.5625ms = = 390.60s (MAX1496) 4 4 Figure 5. Two-Digit Common-Cathode Configuration TON DIGIT 4 (MSD) DIGIT 3 DIGIT 2 DIGIT 1 DIGIT 0 (LSD) T DATA 4 MSD 3 2 1 0 LSD 4 3 2 1 0 4 0 LSD 3 2 1 0 3 2 1 Figure 6. LED Voltage Waveform--MAX1447/MAX1498 TON DIGIT 3 (MSD) DIGIT 2 DIGIT 1 DIGIT 0 (LSD) T DATA 3 MSD 2 1 Figure 7. LED Voltage Waveform--MAX1496 ______________________________________________________________________________________ 13 MAX1447/MAX1496/MAX1498 Figure 5 shows a typical common-cathode configuration for two digits. In common-cathode configuration, the cathodes of all LEDs in a digit are connected together. Each segment driver of the MAX1447/ MAX1496/MAX1498 connects to its corresponding LED's anodes. For example, segment driver SEGA connects to all LED segments designated as A. Similar configurations are used for other segment drivers. The MAX1447/MAX1496/MAX1498 use a multiplexing scheme to drive one digit at a time. The scan rate is fast enough to make the digits appear to be lit. Figures 6 and 7 show data-timing diagrams for the MAX1447/ MAX1496/MAX1498, where T is the display scan period (typically around 1/512Hz or 1.9531ms for the MAX1447/MAX1498, and 1/640Hz or 1.5625ms for the MAX1496). TON in Figures 6 and 7 denotes the amount of time each digit is on and is calculated as follows: SEGDP MAX1447/MAX1496/MAX1498 3.5- and 4.5-Digit, Single-Chip ADCs with LED Drivers Decimal-Point Control Reference The MAX1447/MAX1496/MAX1498 allow for full decimal-point control and feature leading-zero suppression. Use the DPON, DPSET1, and DPSET2 bits in the control register to set the value of the decimal point (Tables 2 and 3). The MAX1447/MAX1496/MAX1498 overrange and underrange display is shown in Table 4. The MAX1447/MAX1496/MAX1498 reference sets the full-scale range of the ADC transfer function. With a nominal 2.048V reference, the ADC full-scale range is 2V with RANGE = GND. With RANGE = DV DD (MAX1447/MAX1498) or VDD (MAX1496), the full-scale range is 200mV. A decreased reference voltage decreases full-scale range (see the Transfer Functions section). The MAX1447/MAX1496/MAX1498 accept either an external reference or an internal reference (INTREF). The INTREF logic selects the reference mode. For internal-reference operation, set INTREF to DVDD (MAX1447/MAX1498) or VDD (MAX1496), connect REFto GND, and bypass REF+ to GND with a 4.7F capacitor. The internal reference provides a nominal 2.048V source between REF+ and GND. The internal-reference temperature coefficient is typically 40ppm/C. Leading-Zero Suppression The MAX1447/MAX1496/MAX1498 include a leadingzero suppression circuitry to turn off unnecessary zeros. For example, when DPSET1 and DPSET2 = [0,0], 0.0 is displayed instead of 000.0. This feature saves a substantial amount of power from being wasted. Interdigit Blanking The MAX1447/MAX1496/MAX1498 also include an interdigit blanking circuitry. Without this feature, it is possible to see a faint digit next to a digit that is completely on. The interdigit blanking circuitry prevents bleeding over into the next digit for a short period of time. The typical interdigit blanking time is 4s. Table 2. Decimal-Point Control Table--MAX1447/MAX1498 DPON DPSET1 DPSET2 DISPLAY OUTPUT ZERO INPUT READING 0 0 0 18888 0 0 0 1 18888 0 0 1 0 18888 0 0 1 1 18888 0 1 0 0 1888.8 0.0 1 0 1 188.88 0.00 1 1 0 18.888 0.000 1 1 1 1.8888 0.0000 Table 3. Decimal-Point Control Table--MAX1496 DPSET1 DPSET2 DISPLAY OUTPUT ZERO INPUT READING 0 0 188.8 0.0 0 1 18.88 0.00 1 0 1888 0 1 1 1.888 0.000 X = Don't care. Table 4. LED During Overrange and Underrange Conditions 14 CONDITION MAX1496 MAX1447/MAX1498 Overrange 1--- 1---- Underrange -1--- -1---- ______________________________________________________________________________________ 3.5- and 4.5-Digit, Single-Chip ADCs with LED Drivers Figure 8 shows the MAX1447/MAX1496/MAX1498 operating with an external differential reference. In this figure, REF- is connected to the top of the strain gauge and REF+ is connected to the midpoint of the resistordivider of the supply. Figure 9 shows the MAX1447/MAX1496/MAX1498 operating with an external single-ended reference. In this figure, REF- is connected to GND and REF+ is driven with an external 2.048V reference. Bypass REF+ to GND with a 0.47F capacitor. Applications Information Power-On Reset At power-up, the digital filter and modulator circuits reset. The MAX1447/MAX1498 allows 6s for the reference to stabilize before performing enhanced offset calibration. During these 6s, the MAX1447/MAX1498 display 1.2V to 1.5V when a stable reference is detected. If a valid reference is not found, the MAX1447/MAX1498 time out after 6s and begin enhanced offset calibration. Enhanced offset calibration typically lasts 2s. The MAX1447/MAX1498 begin converting after enhanced offset calibration. Offset Calibration The MAX1447/MAX1496/MAX1498 offer on-chip offset calibration. The device offset calibrates during every conversion cycle. Enhanced Offset Calibration (MAX1447 Only) Enhanced offset calibration is a more accurate calibration method that is needed in the case of the 200mV range and 4.5-digit resolution. In addition to enhanced offset calibration at power-up, the MAX1447 performs enhanced calibration on demand by connecting HOLD to AVDD for > 2s. Peak The MAX1447/MAX1496/MAX1498 feature peak-detection circuitry. When activated (PEAK connected to AV DD for the MAX1498/MAX1447 or to VDD for the MAX1496), the devices display only the highest voltage measured to the LED. First, the current ADC result is displayed. The new ADC conversion result is compared to the current result. If the new value is larger than the previous peak value, the new value is displayed. If the new value is less than the previous peak value, the display remains unchanged. Connect PEAK to GND to clear the peak value and disable the peak function. ANALOG SUPPLY FERRITE BEAD 0.1F 0.1F 4.7F THERMOCOUPLE JUNCTION 4.7F AVDD DVDD AIN+ MAX1447 MAX1496 MAX1498 REF+ 0.1F RREF REF0.1F ACTIVE GAUGE MAX1447 MAX1496 MAX1498 AIN0.1F +5V R +2.048V 0.1F REF+ MAX6062 AIN+ REF- AIN- DUMMY GAUGE 0.1F GND R GND Figure 8. Strain-Gauge Application with the MAX1447/MAX1496/ MAX1498 0.47F Figure 9. Thermocouple Application with the MAX1447/MAX1496/ MAX1498 ______________________________________________________________________________________ 15 MAX1447/MAX1496/MAX1498 For external-reference operation, set INTREF to GND. REF+ and REF- are fully differential. For a valid external-reference input, VREF+ must be greater than VREF-. Bypass REF+ and REF- with a 0.1F or greater capacitor to GND in external-reference mode. MAX1447/MAX1496/MAX1498 3.5- and 4.5-Digit, Single-Chip ADCs with LED Drivers Hold Transfer Functions The MAX1447/MAX1496/MAX1498 feature data-hold circuitry. When activated (HOLD is set to AVDD for the MAX1447/MAX1498 or to VDD for the MAX1496), the device holds the current reading on the LED. Figures 10-13 show the transfer functions of the MAX1447/MAX1496/MAX1498. The transfer function for the MAX1447/MAX1498 with AIN+ - AIN- 0, RANGE = GND is: Strain-Gauge Measurement Connect the differential inputs of the MAX1447/ MAX1496/MAX1498 to the bridge network of the strain gauge. In Figure 8, the analog supply voltage powers the bridge network and the MAX1447/MAX1496/ MAX1498, along with the reference voltage. The MAX1447/MAX1496/MAX1498 handle an analog input voltage range of 200mV and 2V full scale. The analog/reference inputs of the parts allow the analog input range to have an absolute value of anywhere between -2.2V and +2.2V. Thermocouple Measurement Figure 9 shows a connection from a thermocouple to the MAX1447/MAX1496/MAX1498. In this application, the MAX1447/MAX1496/MAX1498 take advantage of the on-chip input buffers that allow large source impedances on the front end. The decoupling capacitors reduce noise pickup from the thermocouple leads. To place the differential voltage from the thermocouple at a suitable common-mode voltage, the AIN- input of the MAX1447/MAX1496/MAX1498 is biased to GND. Use an external temperature sensor, such as the DS75, and a microcontroller to perform cold-junction temperature compensation. The transfer function for the MAX1447/MAX1498 with AIN+ - AIN- < 0, RANGE = GND is: V -V COUNT = 1.024 AIN+ AIN- x 20,000 + 1 VREF + - VREF - The transfer function for the MAX1447/MAX1498 with AIN+ - AIN- 0, RANGE = DVDD is: V -V COUNT = 1.024 AIN+ AIN- x 20,000 x 10 VREF + - VREF - The transfer function for the MAX1447/MAX1498 with AIN+ - AIN- < 0, RANGE = DVDD is: V -V COUNT = 1.024 AIN+ AIN- x 20,000 x 10 + 1 VREF + - VREF - LED LED 1---- 1---- 19,999 19,999 2 2 1 1 0 0 -0 -0 -1 -1 -2 -2 -19,999 -19,999 -1---- -1----2V -100V 0 100V +2V ANALOG INPUT VOLTAGE Figure 10. MAX1447/MAX1498 Transfer Function, 2V Range 16 V -V COUNT = 1.024 AIN+ AIN- x 20,000 VREF + - VREF - -200mV -10V 0 10V +200mV ANALOG INPUT VOLTAGE Figure 11. MAX1447/MAX1498 Transfer Function, 200mV Range ______________________________________________________________________________________ 3.5- and 4.5-Digit, Single-Chip ADCs with LED Drivers V -V COUNT = 1.024 AIN+ AIN- x 2000 VREF + - VREF - The transfer function for the MAX1496 with AIN+ - AIN< 0, RANGE = GND is: V -V COUNT = 1.024 AIN+ AIN- x 2000 + 1 VREF + - VREF - The transfer function for the MAX1496 with AIN+ - AIN 0, RANGE = VDD is: V -V COUNT = 1.024 AIN+ AIN- x 2000 x 10 VREF + - VREF - The transfer function for the MAX1496 with AIN+ - AIN< 0, RANGE = VDD is: V -V COUNT = 1.024 AIN+ AIN- x 2000 x 10 + 1 VREF + - VREF - Supplies, Layout, and Bypassing Power up AVDD and DVDD (MAX1447/MAX1498) and VDD (MAX1496) before applying an analog input and external-reference voltage to the device. If this is not possible, limit the current into these inputs to 50mA. When the analog and digital supplies come from the same source, isolate the digital supply from the analog supply with a low-value resistor (10) or ferrite bead. For best performance, ground the MAX1447/ MAX1496/MAX1498 to the analog ground plane of the circuit board. Avoid running digital lines under the device as this can couple noise onto the IC. Run the analog ground plane under the MAX1447/MAX1496/MAX1498 to minimize coupling of digital noise. Make the power-supply lines to the MAX1447/MAX1496/MAX1498 as wide as possible to provide low-impedance paths and reduce the effects of glitches on the power-supply line. Shield fast-switching signals, such as clocks, with digital ground to avoid radiating noise to other sections of the board. Avoid running clock signals near the analog inputs. Avoid crossover of digital and analog signals. Running traces that are on opposite sides of the board at right angles to each other reduces feedthrough effects. Good decoupling is important when using high-resolution ADCs. Decouple the supplies with 0.1F ceramic capacitors to GND. Place these components as close to the device as possible to achieve the best decoupling. LED LED 1--- 1--- 1999 1999 2 2 1 1 0 0 -0 -0 -1 -1 -2 -2 -1999 -1999 -1--- -1---200mV -100V 0 100V +200mV ANALOG INPUT VOLTAGE Figure 12. MAX1496 Transfer Function, 200mV Range -2V -1mV 0 1mV +2V ANALOG INPUT VOLTAGE Figure 13. MAX1496 Transfer Function, 2V Range ______________________________________________________________________________________ 17 MAX1447/MAX1496/MAX1498 The transfer function for the MAX1496 with AIN+ - AIN 0, RANGE = GND is: MAX1447/MAX1496/MAX1498 3.5- and 4.5-Digit, Single-Chip ADCs with LED Drivers Selecting Segment Current A resistor from ISET to ground sets the current for each LED segment. See Table 5 for more detail. Use the following formula to set the segment current: 1.20V ISEG = x 450 RISET RISET values below 25k increase the ISEG. However, the internal current-limit circuit limits the ISEG to less than 30mA. At higher ISEG values, proper operation of the device is not guaranteed. In addition, the power dissipated may exceed the package power-dissipation limit. Choosing Supply Voltage to Minimize Power Dissipation The MAX1447/MAX1496/MAX1498 drive a peak current of 25.5mA into LEDs with a 2.2V forward voltage drop when operated from a supply voltage of at least 3.0V. Therefore, the minimum voltage drop across the internal LED drivers is (3.0V - 2.2V) = 0.8V. The MAX1447/ MAX1496/MAX1498 sink (8 x 25.5mA = 204mA) when the outputs are operating and the LED segment drivers are at full current. For a 3.3V supply, the MAX1447/ MAX1496/MAX1498 dissipate (3.3V - 2.2V) x 204 = 224.4mW. If a higher supply voltage is used, the driver absorbs a higher voltage, and the driver's power dissipation increases accordingly. However, if the LEDs used have a higher forward voltage drop than 2.2V, the supply voltage must be raised accordingly to ensure that the driver always has at least 0.8V headroom. For a VLED supply voltage of 2.7V, the maximum LED forward voltage is 1.9V to ensure 0.8V driver headroom. The voltage drop across the drivers with a nominal +5V supply (5.0V - 2.2V = 2.8V) is almost three times the drop across the drivers with a nominal 3.3V supply (3.3V - 2.2V = 1.1V). Therefore, the driver's power dissipation increases three times. The power dissipation in the part causes the junction temperature to rise accordingly. In the high ambient temperature case, the total junction temperature may be very high (>+125C). At higher junction temperatures, the ADC performance degrades. To ensure the dissipation limit for the MAX1447/MAX1496/MAX1498 is not exceeded and the ADC performance is not degraded, a diode can be inserted between the power supply and VLED. 18 Table 5. Segment-Current Selection RISET (k) ISEG (mA) 25 21.6 50 10.8 100 5.4 500 1.1 >2500 LED driver disabled Computing Power Dissipation The following can be used to compute power dissipation: PD = (VLED x IVLED ) + (VLED - VDIODE) (DUTY x ISEG x N) + VSUPPLY x ISUPPLY VLED = LED driver supply voltage IVLED = VLED bias current VDIODE = LED forward voltage DUTY = segment ON time during each digit ON time ISEG = segment current set by RISET N = number of segments driven (worst case is eight) VSUPPLY = supply voltage of the part ISUPPLY = supply current from VDD for the MAX1496 or AVDD + DVDD for the MAX1447/MAX1498. Dissipation Example For ISEG = 25.5mA, N = 8, DUTY = 127 / 128, VDIODE = 1.5V at 25.5mA, VLED = VSUPPLY = 5.25V: PD = (5.25 x 2mA) + (5.25V - 1.5) [(127 / 128) x 25.5mA x 8)] + 5.25 x 1.080mA PD = 0.7751W 28-Pin SSOP-Package Example For the 28-pin SSOP package (TJA = 1 / 0.009496 = +105.3C/W), the maximum allowed ambient temperature TA is given by: TJ (max) = TA + (PD x TJA) = +125C = TA + (0.7751W x +105.3C/W) TA = +43C Thus, the device cannot operate safely at a maximum package temperature of +85C. The power dissipates in the part need to be lowered. ______________________________________________________________________________________ 3.5- and 4.5-Digit, Single-Chip ADCs with LED Drivers 28-Pin PDIP-Package Example PD x TJA (max) = (+125C) - (+85C) = +40C PD (max) = +40C / +70C/W = 571mW VLED - VDIODE = [571mW - (5.25V x 2mA) - 5.25V x 1.080mA] / [(127 / 128) x 25.5mA x 8] VLED - VDIODE = 2.80V For a 28-pin PDIP package, VLED - VDIODE should have the following condition to ensure it operates safely: 0.8V < VLED - VDIODE < 2.80V 32-Pin TQFP Package The MAX1447/MAX1498 TQFP package can operate safely for all supply voltages provided VDIODE > 1.5V. Definitions INL Integral nonlinearity (INL) is the deviation of the values on an actual transfer function from a straight line. This straight line is either a best-straight-line fit or a line drawn between the end points of the transfer function, once offset and gain errors have been nullified. INL for the MAX1447/MAX1496/MAX1498 is measured using the end-point method. DNL Rollover Error Rollover error is defined as the absolute-value difference between a near positive full-scale reading and near negative full-scale reading. Rollover error is tested by applying a full-scale positive voltage, swapping AIN+ and AIN-, and adding the results. Zero Input Reading Ideally, with AIN+ connected to AIN-, the MAX1447/ MAX1496/MAX1498 LED displays zero. Zero input reading is the measured deviation from the ideal zero and the actual measured point. Gain Error Gain error is the amount of deviation between the measured full-scale transition point and the ideal full-scale transition point. Common-Mode Rejection Common-mode rejection (CMR) is the ability of a device to reject a signal that is common to both input terminals. The common-mode signal can be either an AC or a DC signal or a combination of the two. CMR is often expressed in decibels. Normal-Mode 50Hz and 60Hz Rejection (Simultaneously) Normal-mode rejection is a measure of how much output changes when 50Hz and 60Hz signals are injected into only one of the differential inputs. The MAX1447/ MAX1496/MAX1498 sigma-delta converter uses its internal digital filter to provide normal-mode rejection to both 50Hz and 60Hz power-line frequencies simultaneously. Power-Supply Rejection Ratio Power-supply rejection ratio (PSRR) is the ratio of the input supply change (in volts) to the change in the converter output (in volts). It is typically measured in decibels. Differential nonlinearity (DNL) is the difference between an actual step width and the ideal value of 1 LSB. A DNL error specification of less than 1 LSB guarantees no missing codes and a monotonic transfer function. ______________________________________________________________________________________ 19 MAX1447/MAX1496/MAX1498 (PD x TJA) max = (+125C) - (+85C) = +40C PD (max) = +40C /+105.3C/W = 380mW (VLED - VDIODE) = [380mW - (5.25V x 2mA) - 5.25V x 1.080mA] / [(127 / 128) x 25.5mA x 8] VLED - VDIODE = 1.854V VLED - VDIODE should have the following condition to ensure it operates safely: 0.8V < VLED - VDIODE < 1.854V 3.5- and 4.5-Digit, Single-Chip ADCs with LED Drivers MAX1447/MAX1496/MAX1498 Typical Operating Circuits DIG0-DIG4 DIGIT CONNECTIONS SEGA-SEGDP SEGMENT CONNECTIONS AIN+ VIN AIN- DPSET2 VLED DPSET1 RANGE MAX1447 MAX1498 DVDD INTREF 0.1F 10F PEAK HOLD AVDD DPON 0.1F ISET LISO VNEG GND REF- REF+ 0.1F GLED 4.7F 25k 2.7V TO 5.25V 10F VIN DIG0-DIG3 DIGIT CONNECTIONS SEGA-SEGDP SEGMENT CONNECTIONS AIN+ AIN- DPSET2 VLED DPSET1 10F RANGE MAX1496 VDD INTREF 0.1F PEAK HOLD 2.7V TO 5.25V ISET VNEG GND 0.1F REF- REF+ GLED 4.7F 25k 20 ______________________________________________________________________________________ 3.5- and 4.5-Digit, Single-Chip ADCs with LED Drivers VNEG 1 28 SEGDP REF- VNEG DPON LED_EN SEGDP SEGG SEGF VLED TOP VIEW REF- 2 27 SEGG 32 31 30 29 28 27 26 25 REF+ 3 26 SEGF AIN+ 4 25 VLED AIN- 5 24 SEGE ISET 6 MAX1496 23 SEGD REF+ 1 24 SEGE AIN+ 2 23 SEGD AIN- 3 22 SEGC ISET 4 21 SEGB GND 7 22 SEGC VDD 8 21 SEGB INTREF 9 20 SEGA AVDD 6 19 DIG4 RANGE 10 19 DIG3 DVDD 7 18 DIG3 DPSET1 11 18 DIG2 INTREF 8 17 DIG2 DPSET2 12 17 GLED PEAK 13 16 DIG1 HOLD 14 15 DIG0 SSOP/PDIP 13 14 15 16 DIG1 GLED DPSET2 12 DIG0 11 HOLD 10 20 SEGA PEAK 9 DPSET1 5 RANGE GND MAX1447 MAX1498 TQFP Chip Information TRANSISTOR COUNT: 80,000 PROCESS: BiCMOS ______________________________________________________________________________________ 21 MAX1447/MAX1496/MAX1498 Pin Configurations Package Information (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.) 32L/48L,TQFP.EPS MAX1447/MAX1496/MAX1498 3.5- and 4.5-Digit, Single-Chip ADCs with LED Drivers 22 ______________________________________________________________________________________ 3.5- and 4.5-Digit, Single-Chip ADCs with LED Drivers SSOP.EPS 2 1 INCHES E H MILLIMETERS DIM MIN MAX MIN MAX A 0.068 0.078 1.73 1.99 A1 0.002 0.008 0.05 0.21 B 0.010 0.015 0.25 0.38 C 0.20 0.09 0.004 0.008 SEE VARIATIONS D E e 0.205 0.212 0.0256 BSC 5.20 MILLIMETERS INCHES D D D D D 5.38 MIN MAX MIN MAX 0.239 0.239 0.278 0.249 0.249 0.289 6.07 6.07 7.07 6.33 6.33 7.33 0.317 0.397 0.328 0.407 8.07 10.07 8.33 10.33 N 14L 16L 20L 24L 28L 0.65 BSC H 0.301 0.311 7.65 7.90 L 0.025 0 0.037 8 0.63 0 0.95 8 N A C B e A1 L D NOTES: 1. D&E DO NOT INCLUDE MOLD FLASH. 2. MOLD FLASH OR PROTRUSIONS NOT TO EXCEED .15 MM (.006"). 3. CONTROLLING DIMENSION: MILLIMETERS. 4. MEETS JEDEC MO150. 5. LEADS TO BE COPLANAR WITHIN 0.10 MM. PROPRIETARY INFORMATION TITLE: PACKAGE OUTLINE, SSOP, 5.3 MM APPROVAL DOCUMENT CONTROL NO. 21-0056 REV. C 1 1 ______________________________________________________________________________________ 23 MAX1447/MAX1496/MAX1498 Package Information (continued) (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.) Package Information (continued) (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.) D1 N DIM A A1 A2 A3 B B1 C D1 E E1 e eA eB L 1 TOP VIEW E D E1 A3 A1 A A2 e MILLIMETERS MAX MIN 5.08 0.39 3.18 4.45 2.03 1.40 0.51 0.41 1.65 1.14 0.21 0.30 0.13 0.22 15.24 15.87 13.34 14.61 2.54 BSC 15.24 BSC 3.05 17.78 3.81 VARIATIONS: INCHES 0-15 L INCHES MAX MIN 0.200 0.015 0.125 0.175 0.080 0.055 0.020 0.016 0.065 0.045 0.012 0.008 0.009 0.005 0.625 0.600 0.525 0.575 0.100 BSC 0.600 BSC 0.700 0.120 0.150 PDIPW.EPS MAX1447/MAX1496/MAX1498 3.5- and 4.5-Digit, Single-Chip ADCs with LED Drivers C B1 B eA eB FRONT VIEW MILLIMETERS DIM D MIN 1.230 MAX 1.270 MIN 31.24 MAX 32.26 N MS011 24 AA D D 1.430 2.025 1.470 2.075 36.32 51.44 37.34 52.71 28 40 AB AC SIDE VIEW PROPRIETARY INFORMATION TITLE: PACKAGE OUTLINE, .600" PDIP APPROVAL DOCUMENT CONTROL NO. 21-0044 REV. B 1 1 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 24 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 (c) 2004 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products.