DS90C032 DS90C032 LVDS Quad CMOS Differential Line Receiver Literature Number: SNLS094C DS90C032 LVDS Quad CMOS Differential Line Receiver General Description Features TheDS90C032 is a quad CMOS differential line receiver designed for applications requiring ultra low power dissipation and high data rates. The device is designed to support data rates in excess of 155.5 Mbps (77.7 MHz) utilizing Low Voltage Differential Signaling (LVDS) technology. TheDS90C032 accepts low voltage (350 mV) differential input signals and translates them to CMOS (TTL compatible) output levels. The receiver supports a TRI-STATE(R) function that may be used to multiplex outputs. The receiver also supports OPEN, shorted and terminated (100) input Failsafe with the addition of external failsafe biasing. Receiver output will be HIGH for both Failsafe conditions. TheDS90C032 and companion line driver (DS90C031) provide a new alternative to high power psuedo-ECL devices for high speed point-to-point interface applications. >155.5 Mbps (77.7 MHz) switching rates Accepts small swing (350 mV) differential signal levels Ultra low power dissipation 600 ps maximum differential skew (5V, 25C) 6.0 ns maximum propagation delay Industrial operating temperature range Military operating temperature range option Available in surface mount packaging (SOIC) and (LCC) Pin compatible with DS26C32A, MB570 (PECL) and 41LF (PECL) Supports OPEN input fail-safe Supports short and terminated input fail-safe with the addition of external failsafe biasing Compatible with IEEE 1596.3 SCI LVDS standard Conforms to ANSI/TIA/EIA-644 LVDS standard Available to Standard Microcircuit Drawing (SMD) 5962-95834 Connection Diagrams Dual-In-Line LCC Package 1194501 Order Number DS90C032TM See NS Package Number M16A 1194520 Order Number DS90C032E-QML See NS Package Number E20A For complete Military Specifications, refer to appropriate SMD or MDS. TRI-STATE(R) is a registered trademark of National Semiconductor Corporation. (c) 2007 National Semiconductor Corporation 11945 www.national.com DS90C032 LVDS Quad CMOS Differential Line Receiver May 2007 DS90C032 Functional Diagram and Truth Tables 1194502 Receiver ENABLES www.national.com EN EN* L H INPUTS OUTPUT RIN+ - RIN- ROUT X Z All other combinations VID 0.1V H of ENABLE inputs VID -0.1V L Full Fail-safe OPEN/SHORT or Terminated H 2 If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage (VCC) -0.3V to +6V Input Voltage (RIN+, RIN-) -0.3V to (VCC +0.3V) Enable Input Voltage -0.3V to (VCC +0.3V) (EN, EN*) Output Voltage (ROUT) -0.3V to (VCC +0.3V) Maximum Package Power Dissipation @ +25C M Package 1025 mW E Package 1830 mW Derate M Package 8.2 mW/C above +25C Derate E Package 12.2 mW/C above +25C Storage Temperature Range -65C to +150C Lead Temperature Range Soldering (4 sec.) +260C +150C +175C 3,500V 250V (HBM, 1.5 k, 100 pF) (EIAJ, 0 , 200 pF) Recommended Operating Conditions Min Typ Supply Voltage (VCC) +4.5 +5.0 Receiver Input Voltage GND Operating Free Air Temperature (TA) DS90C032T -40 +25 DS90C032E -55 +25 Max +5.5 2.4 Units V V +85 +125 C C Electrical Characteristics Over Supply Voltage and Operating Temperature ranges, unless otherwise specified. (Note 2) Symbol Parameter VTH Differential Input High Threshold VTL Differential Input Low Threshold IIN Input Current VOH Output High Voltage Conditions Pin VCM = +1.2V RIN+, RIN- VIN = +2.4V VCC = 5.5V IOH = -0.4 mA, ROUT DS90C032T Typ Max Units +100 mV -100 mV 1 +10 A -10 1 +10 A 3.8 4.9 V 3.8 4.9 V -10 VIN = 0V IOH = -0.4 mA, VID = +200 mV Min Input terminated VOL Output Low Voltage IOL = 2 mA, VID = -200 mV IOS Output Short Circuit Current Enabled, VOUT = 0V (Note 8) IOZ Output TRI-STATE Current Disabled, VOUT = 0V or VCC VIH Input High Voltage VIL Input Low Voltage II Input Current VCL Input Clamp Voltage ICL = -18 mA ICC No Load Supply Current EN, EN* = VCC or GND, DS90C032T Receivers Enabled Inputs Open DS90C032E ICCZ EN, EN* 0.3 V -15 -60 -100 mA -10 1 +10 A 2.0 V -10 1 -1.5 -0.8 0.8 V +10 A V 3.5 10 mA 3.5 11 mA EN, EN* = 2.4 or 0.5, Inputs Open 3.7 11 mA No Load Supply Current EN = GND, EN* = VCC DS90C032T 3.5 10 mA Receivers Disabled Inputs Open DS90C032E 3.5 11 mA 3 VCC 0.07 www.national.com DS90C032 Maximum Junction Temperature (DS90C032T) Maximum Junction Temperature (DS90C032E) ESD Rating (Note 7) Absolute Maximum Ratings (Note 1) DS90C032 Switching Characteristics VCC = +5.0V, TA = +25C DS90C032T (Notes 3, 4, 5, 9) Symbol Min Typ Max Units tPHLD Differential Propagation Delay High to Low Parameter CL = 5 pF 1.5 3.40 5.0 ns tPLHD Differential Propagation Delay Low to High VID = 200 mV 1.5 3.48 5.0 ns tSKD Differential Skew |tPHLD - tPLHD| 0 80 600 ps tSK1 Channel-to-Channel Skew (Note 5) 0 0.6 1.0 ns tTLH Rise Time 0.5 2.0 ns tTHL Fall Time 0.5 2.0 ns tPHZ Disable Time High to Z RL = 2 k 10 15 ns tPLZ Disable Time Low to Z CL = 10 pF 10 15 ns 4 10 ns 4 10 ns tPZH Enable Time Z to High tPZL Enable Time Z to Low Conditions (Figure 1 and Figure 2) (Figure 3 and Figure 4) Switching Characteristics VCC = +5.0V 10%, TA = -40C to +85C DS90C032T (Notes 3, 4, 5, 6, 9) Symbol Min Typ Max Units Differential Propagation Delay High to Low CL = 5 pF 1.0 3.40 6.0 ns tPLHD Differential Propagation Delay Low to High VID = 200 mV 1.0 3.48 6.0 ns tSKD Differential Skew |tPHLD - tPLHD| 0 0.08 1.2 ns tSK1 Channel-to-Channel Skew (Note 5) 0 0.6 1.5 ns tSK2 Chip to Chip Skew (Note 6) 5.0 ns tTLH Rise Time 0.5 2.5 ns tTHL Fall Time 0.5 2.5 ns tPHZ Disable Time High to Z RL = 2 k 10 20 ns tPLZ Disable Time Low to Z CL = 10 pF 10 20 ns tPZH Enable Time Z to High 4 15 ns tPZL Enable Time Z to Low 4 15 ns tPHLD Parameter Conditions (Figure 1 and Figure 2) (Figure 3 and Figure 4) Switching Characteristics VCC = +5.0V 10%, TA = -55C to +125C DS90C032E (Notes 3, 4, 5, 6, 9, 10) Min Typ Max Units tPHLD Symbol Differential Propagation Delay High to Low Parameter CL = 20 pF 1.0 3.40 8.0 ns tPLHD Differential Propagation Delay Low to High VID = 200 mV 1.0 3.48 8.0 ns tSKD Differential Skew |tPHLD - tPLHD| 0 0.08 3.0 ns tSK1 Channel-to-Channel Skew (Note 5) 0 0.6 3.0 ns tSK2 Chip to Chip Skew (Note 6) 7.0 ns tPHZ Disable Time High to Z RL = 2 k 10 20 ns tPLZ Disable Time Low to Z CL = 10 pF 10 20 ns tPZH Enable Time Z to High (Figure 3 and Figure 4) 4 20 ns tPZL Enable Time Z to Low 4 20 ns www.national.com Conditions (Figure 1 and Figure 2) 4 DS90C032 Parameter Measurement Information 1194503 FIGURE 1. Receiver Propagation Delay and Transition Time Test Circuit 1194504 FIGURE 2. Receiver Propagation Delay and Transition Time Waveforms 1194505 CL includes load and test jig capacitance. S1 = VCC for tPZL and tPLZ measurements. S1 = GND for tPZH and tPHZ measurements. FIGURE 3. Receiver TRI-STATE Delay Test Circuit 5 www.national.com DS90C032 1194506 FIGURE 4. Receiver TRI-STATE Delay Waveforms Typical Application 1194507 FIGURE 5. Point-to-Point Application ground), exceeding these limits may turn on the ESD protection circuitry which will clamp the bus voltages. Receiver Fail-Safe: The LVDS receiver is a high gain, high speed device that amplifies a small differential signal (20mV) to CMOS logic levels. Due to the high gain and tight threshold of the receiver, care should be taken to prevent noise from appearing as a valid signal. The receiver's internal fail-safe circuitry is designed to source/ sink a small amount of current, providing fail-safe protection (a stable known state of HIGH output voltage) for floating, terminated or shorted receiver inputs. 1. Open Input Pins. TheDS90C032 is a quad receiver device, and if an application requires only 1, 2 or 3 receivers, the unused channel(s) inputs should be left OPEN. Do not tie unused receiver inputs to ground or any other voltages. The input is biased by internal high value pull up and pull down resistors to set the output to a HIGH state. This internal circuitry will guarantee a HIGH, stable output state for open inputs. 2. Terminated Input. TheDS90C032 requires external failsafe biasing for terminated input failsafe. Terminated input failsafe is the case of a receiver that has a 100 termination across its inputs and the driver is in the following situations. Unplugged from the bus, or the driver output is in TRI-STATE or in power-off condition. The use of external biasing resistors provide a small bias to set the differential input voltage while the line is un-driven, and therefore the receiver output will be in HIGH state. If the driver is removed from the bus but Applications Information LVDS drivers and receivers are intended to be primarily used in an uncomplicated point-to-point configuration as is shown in Figure 5. This configuration provides a clean signaling environment for the quick edge rates of the drivers. The receiver is connected to the driver through a balanced media which may be a standard twisted pair cable, a parallel pair cable, or simply PCB traces. Typically the characteristic impedance of the media is in the range of 100. A termination resistor of 100 should be selected to match the media, and is located as close to the receiver input pins as possible. The termination resistor converts the current sourced by the driver into a voltage that is detected by the receiver. Other configurations are possible such as a multi-receiver configuration, but the effects of a mid-stream connector(s), cable stub(s), and other impedance discontinuities as well as ground shifting, noise margin limits, and total termination loading must be taken into account. TheDS90C032 differential line receiver is capable of detecting signals as low as 100 mV, over a 1V common-mode range centered around +1.2V. This is related to the driver offset voltage which is typically +1.2V. The driven signal is centered around this voltage and may shift 1V around this center point. The 1V shifting may be the result of a ground potential difference between the driver's ground reference and the receiver's ground reference, the common-mode effects of coupled noise, or a combination of the two. Both receiver input pins should honor their specified operating input voltage range of 0V to +2.4V (measured from each pin to www.national.com 6 4. quality reasons. First, only an application that requires failsafe biasing needs to employ it. Second, the amount of failsafe biasing is now an application design parameter and can be custom tailored for the specific application. In applications in low noise environments, they may choose to use a very small bias if any. For applications with less balanced interconnects and/or in high noise environments they may choose to boost failsafe further. Nationals "LVDS Owner's Manual provides detailed calculations for selecting the proper failsafe biasing resistors. Third, the common-mode voltage is biased by the resistors during the un-driven state. This is selected to be close to the nominal driver offset voltage (VOS). Thus when switching between driven and un-driven states, the common-mode modulation on the bus is held to a minimum. For additional Failsafe Biasing information, please refer to Application Note AN-1194 for more detail. The footprint of theDS90C032 is the same as the industry standard 26LS32 Quad Differential (RS-422) Receiver. 7 www.national.com DS90C032 3. the cable is still present and floating, the unplugged cable can become a floating antenna that can pick up noise. The LVDS receiver is designed to detect very small amplitude and width signals and recover them to standard logic levels. Thus, if the cable picks up more than 10mV of differential noise, the receiver may respond. To insure that any noise is seen as commonmode and not differential, a balanced interconnect and twisted pair cables is recommended, as they help to ensure that noise is coupled common to both lines and rejected by the receivers. Shorted Inputs. If a fault condition occurs that shorts the receiver inputs together, thus resulting in a 0V differential input voltage, the receiver output will remain in a HIGH state. Shorted input fail-safe is not supported across the common-mode range of the device (1.2V 1V). It is only supported with inputs shorted and no external common-mode voltage applied. Operation in environment with greater than 10mV differential noise. National recommends external failsafe biasing on its LVDS receivers for a number of system level and signal DS90C032 Note 1: "Absolute Maximum Ratings" are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the devices should be operated at these limits. The table of "Electrical Characteristics" specifies conditions of device operation. Pin Descriptions Pin No. Name Description (SOIC) 2, 6, 10, 14 RIN+ Non-inverting receiver input pin 1, 7, 9, 15 RIN- Inverting receiver input pin Note 2: Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground unless otherwise specified. Note 3: All typicals are given for: VCC = +5.0V, TA = +25C. Note 4: Generator waveform for all tests unless otherwise specified: f = 1 MHz, ZO = 50, tr and tf (0%-100%) 1 ns for RIN and tr and tf 6 ns for EN or EN*. 3, 5, 11, ROUT Receiver output pin 13 Note 5: Channel-to-Channel Skew is defined as the difference between the propagation delay of one channel and that of the others on the same chip with an event on the inputs. 4 EN Active high enable pin, OR-ed with EN* 12 EN* Active low enable pin, OR-ed with EN Note 6: Chip to Chip Skew is defined as the difference between the minimum and maximum specified differential propagation delays. 16 VCC Power supply pin, +5V 10% Note 7: ESD Rating: 8 GND Ground pin HBM (1.5 k, 100 pF) 3,500V EIAJ (0, 200 pF) 250V Ordering Information Operating Temperature Package Type/ Number Order Number -40C to +85C SOP/M16A DS90C032TM -55C to +125C LCC/E20A DS90C032E-QML Note 8: Output short circuit current (IOS) is specified as magnitude only, minus sign indicates direction only. Only one output should be shorted at a time, do not exceed maximum junction temperature specification. Note 9: CL includes probe and jig capacitance. Note 10: For DS90C032E propagation delay measurements are from 0V on the input waveform to the 50% point on the output (ROUT). DS90C032E-QML (NSID) 5962-95834 (SMD) Typical Performance Characteristics Output High Voltage vs Power Supply Voltage Output High Voltage vs Ambient Temperature 1194508 www.national.com 1194509 8 DS90C032 Output Low Voltage vs Power Supply Voltage Output Low Voltage vs Ambient Temperature 1194510 1194511 Output Short Circuit Current vs Power Supply Voltage Output Short Circuit Current vs Ambient Temperature 1194512 1194513 Differential Propagation Delay vs Power Supply Voltage Differential Propagation Delay vs Ambient Temperature 1194514 1194515 9 www.national.com DS90C032 Differential Skew vs Power Supply Voltage Differential Skew vs Ambient Temperature 1194517 1194516 Transition Time vs Power Supply Voltage Transition Time vs Ambient Temperature 1194518 www.national.com 1194519 10 DS90C032 Physical Dimensions inches (millimeters) unless otherwise noted 20-Lead Ceramic Leadless Chip Carrier, Type C Order Number DS90C032E-QML NS Package Number E20A 16-Lead (0.150 Wide) Molded Small Outline Package, JEDEC Order Number DS90C032TM NS Package Number M16A 11 www.national.com DS90C032 LVDS Quad CMOS Differential Line Receiver Notes THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2007 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530-85-86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +49 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated