AC-DC Power Supplies Open Frame/ Enclosed Type LEP100F Ordering information LEP 100 1 2 F 3 -24 4 Example recommended EMI/EMC filter NAC-06-472 R High voltage pulse noise type : NAP series Low leakage current type : NAM series * A higher current rating EMI/EMC filter may be recommended in view of the other devices that could be connected in parallel with the power supply. -O 5 1Series name 2Output wattage 3Universal input 4Output voltage 5Optional *1 *6 G :Low leakage current R :with Remote ON/OFF S :with Chassis SN:with Chassis & cover T :Vertical terminal block U :Operating stop voltage is set at a lower value Z :with ZT *Make sure necessary tests will be carried out on your end equipment with the power supply installed in accordance with any required EMC/EMI regulations. MODEL DC OUTPUT LEP100F-24 +24V 4.2(Peak 7)A LEP100F-36 +36V 2.8(Peak 4.7)A LEP100F-48 +48V 2.1(Peak 3.5)A SPECIFICATIONS MODEL VOLTAGE[V] CURRENT[A] ACIN 100V ACIN 200V FREQUENCY[Hz] INPUT OUTPUT PROTECTION CIRCUIT AND OTHERS ISOLATION ENVIRONMENT SAFETY AND NOISE REGULATIONS OTHERS ACIN 100V ACIN 200V ACIN 100V POWER FACTOR ACIN 200V ACIN 100V INRUSH CURRENT[A] ACIN 200V LEAKAGE CURRENT[mA] VOLTAGE[V] CURRENT[A] *2 WATTAGE[W] LINE REGULATION[mV] LOAD REGULATION[mV] 0 to +50C *3 RIPPLE[mVp-p] -10 - 0C *3 0 to +50C *3 RIPPLE NOISE[mVp-p] -10 - 0C *3 0 to +50C TEMPERATURE REGULATION[mV] -10 to +50C DRIFT[mV] *4 START-UP TIME[ms] HOLD-UP TIME[ms] OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V] OVERCURRENT PROTECTION OVERVOLTAGE PROTECTION REMOTE ON/OFF INPUT-OUTPUT -RC *5 INPUT-FG OUTPUT-RC-FG *5 OUTPUT-RC *5 OPERATING TEMP.,HUMID.AND ALTITUDE STORAGE TEMP.,HUMID.AND ALTITUDE VIBRATION IMPACT AGENCY APPROVALS CONDUCTED NOISE HARMONIC ATTENUATOR CASE SIZE/WEIGHT COOLING METHOD EFFICIENCY[%] LEP100F-24 LEP100F-36 LEP100F-48 AC85 - 264 1f or DC 120 - 370 1.4typ (Io=100%) 0.7typ (Io=100%) 50/60 (47 - 63) or DC 81typ (Io=100%) 82typ (Io=100%) 83typ (Io=100%) 84typ (Io=100%) 85typ (Io=100%) 85typ (Io=100%) 0.98typ (Io=100%) 0.93typ (Io=100%) 15typ (Io=100%) (At cold start) (Ta=25 C) 30typ (Io=100%) (At cold start) (Ta=25 C) 0.75max (60Hz, According to IEC60950 and DEN-AN) +24 +36 +48 0 - 4.2 (Peak 7) 0 - 2.8 (Peak 4.7) 0 - 2.1 (Peak 3.5) 100.8 (Peak 168) 100.8 (Peak 169.2) 100.8 (Peak 168) 48max 48max 48max 76max 90max 150max 120max 120max 150max 160max 160max 300max 150max 150max 250max 180max 180max 350max 120max 150max 240max 145max 180max 300max 48max 48max 48max 500max (ACIN 100V, Io=100%) 20typ (ACIN 100V, Io=100%) 21.4 - 26.4 26.4 - 39.6 39.6 - 52.8 23.0 - 25.0 35.0 - 37.0 46.0 - 50.0 Works over 101% of peak current and recovers automatically Works at 115 - 140% of rating Option (Refer to Instruction Manual) AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC500V 1minute, Cutoff current = 100mA, DC500V 50MW min (At Room Temperature) AC100V 1minute, Cutoff current = 100mA, DC100V 10MW min (At Room Temperature) -10 to +70C, 20 - 90%RH (Non condensing) (Refer to DERATING CURVE), 3,000m (10,000feet) max -20 to +75C, 20 - 90%RH (Non condensing), 9,000m (30,000feet) max 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axis 196.1m/s2 (20G), 11ms, once each X, Y and Z axis UL60950-1, C-UL(CSA60950-1), EN60950-1, EN60065, EN50178 Complies with DEN-AN and IEC60950-1 (At only AC input) Complies with FCC-B, CISPR22-B, EN55022-B, VCCI-B Complies with IEC61000-3-2 *7 75X35X222mm [2.95X1.38X8.74 inches] (W XHXD) /380g max (with chassis & cover : 650g max) Convection *1Specification is changed at option, refer to Instruction Manual 6. *2Peak loading for 10sec. And Duty 35% max, refer to Instruction Manual 5. In detail. *3This is the value that measured on measuring board with capacitor of 22mF within 150mm from output terminal.Measured by 20MHz oscilloscope or Ripple-Noise meter (Equivalent to KEISOKU-GIKEN: RM101). *4Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C, with the input voltage held constant at the rated input/output. LEP-2 *5Applicable when remote control (optional) is added. *6Please contact us about safety approvals for the model with option. *7Please contact us about class C. *Parallel operation with other model is not possible. *Derating is required when operated with chassis and cover. *A sound may occur from power supply at peak loading. LEP100F External view 235-+0.5 [8.35] [0.2] 222 85 4.5 235-+0.5 8 [9.25] [0.31] 20 CN3 RC(-) PCB t=1.6 3max I / O Connector Mating Connector Terminal Chain : SVH-21T-P1.1 CN1 VHR-5N B3P5-VH Loose: BVH-21T-P1.1 Chain : SVH-21T-P1.1 CN2 VHR-8N B8P-VH Loose: BVH-21T-P1.1 Chain : SXH-001T-P0.6 CN3 XHP-2 (Option) B2B-XH-A Loose: BXH-001T-P0.6 Chain : SXH-001T-P0.6 CN4 XHP-3 (Option) B3B-XH-A Loose: BXH-001T-P0.6 (Mfr: J.S.T.) RC(+) + COM - [0.06] CN1 Pin No. Input 1 AC(L) 2 3 AC(N) 4 5 FG [3.35] 42 30 252 [0.18] 4.5 [1.26] CN4 CN3 [9.92] 4.5 2-M4 Mounting Hole [0.12](Lead) 32 [8.74] CN4 46 3.5-4.0 [0.14-0.16] Mounting Hole Connector for -Z (option) [1.81] 212 -+ 0.5 15 5 Connector for Remote ON/OFF (option) [6.93] [0.79] [0.59] [0.2] (176) 5 20 CN3 [0.18] 8 CN4 [0.18] +V CN2 CN1 [1.77] 25-+0.5 [0.98] 4 5 [1.18] CN2 1 Mounting Hole [0.18] 45-+0.5 -V (68) C119 [2.68] 75 [2.95] 65 -+ 0.5 [2.56] CN1 5 FG 3 Input(N) 1 Input(L) 8 [0.31] 4-M4 [9.25] 2-4.5 [0.79] 3-3.5 [0.14] Mounting Hole [1.65] Voltage adjust Name plate PIN CONNECTION CN2 Pin No. Output 1, 2, 3, 4 -V +V 5, 6, 7, 8 CN3 (Option) Pin No. Remote ON/OFF 1 RC(+) 2 RC(-) Weight: 380g max (with chassis & cover : 650g max) Tolerance: t1 [t0.04] Dimensions in mm, [ ]=inches PCB Material : CEM3 Chassis and cover is optional. Mounting torque: 1.5N * m(16kgf * cm)max CN4 (Option) Pin No. -Z 1 + COM 2 3 Keep drawing current per pin below 5A(7A at peak load)for CN2 Performance data RISE TIME & FALL TIME (LEP100F-24) EFFICIENCY (LEP100F-24) 86 ACIN 100V Io=100% EFFICIENCY 84 DC Output AC Input 76 60 20ms/DIV INPUT HARMONIC CURRENT (LEP100F-24) Load factor100% Load factor 50% 100 140 180 220 INPUT VOLTAGE 260 300 V INPUT HARMONIC CURRENT (LEP100F-24) 10 10 HARMONIC CURRENT Load factor 100% Input voltage AC 100V 1 0.1 0.01 10 20 HARMONIC ORDER 30 Harmonic current standard class A (at odd number) A Harmonic current standard class A (at odd number) A HARMONIC CURRENT 80 78 100ms/DIV 0.001 0 82 40 1 Load factor 100% Input voltage AC 230V 0.1 0.01 0.001 0 10 20 30 40 HARMONIC ORDER LEP-3 AC-DC Power Supplies Open Frame/ Enclosed Type LEP150F Ordering information LEP 150 1 2 F 3 -24 4 Example recommended EMI/EMC filter NAC-06-472 R High voltage pulse noise type : NAP series Low leakage current type : NAM series * A higher current rating EMI/EMC filter may be recommended in view of the other devices that could be connected in parallel with the power supply. -O 5 1Series name 2Output wattage 3Universal input 4Output voltage 5Optional *1 *6 G :Low leakage current R :with Remote ON/OFF S :with Chassis SN:with Chassis & cover T :Vertical terminal block U :Operating stop voltage is set at a lower value Z :with ZT *Make sure necessary tests will be carried out on your end equipment with the power supply installed in accordance with any required EMC/EMI regulations. MODEL DC OUTPUT LEP150F-24 +24V 6.3(Peak 12)A LEP150F-36 +36V 4.2(Peak 8)A LEP150F-48 +48V 3.2(Peak 6)A SPECIFICATIONS MODEL VOLTAGE[V] CURRENT[A] ACIN 100V ACIN 200V FREQUENCY[Hz] INPUT OUTPUT PROTECTION CIRCUIT AND OTHERS ISOLATION ENVIRONMENT SAFETY AND NOISE REGULATIONS OTHERS ACIN 100V ACIN 200V ACIN 100V POWER FACTOR ACIN 200V ACIN 100V INRUSH CURRENT[A] ACIN 200V LEAKAGE CURRENT[mA] VOLTAGE[V] CURRENT[A] *2 WATTAGE[W] LINE REGULATION[mV] LOAD REGULATION[mV] 0 to +45C *3 RIPPLE[mVp-p] -10 - 0C *3 0 to +45C *3 RIPPLE NOISE[mVp-p] -10 - 0C *3 0 to +45C TEMPERATURE REGULATION[mV] -10 to +45C DRIFT[mV] *4 START-UP TIME[ms] HOLD-UP TIME[ms] OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V] OVERCURRENT PROTECTION OVERVOLTAGE PROTECTION REMOTE ON/OFF INPUT-OUTPUT -RC *5 INPUT-FG OUTPUT-RC-FG *5 OUTPUT-RC *5 OPERATING TEMP.,HUMID.AND ALTITUDE STORAGE TEMP.,HUMID.AND ALTITUDE VIBRATION IMPACT AGENCY APPROVALS CONDUCTED NOISE HARMONIC ATTENUATOR CASE SIZE/WEIGHT COOLING METHOD EFFICIENCY[%] LEP150F-24 LEP150F-36 LEP150F-48 AC85 - 264 1f or DC 120 - 370 2.0typ (Io=100%) 1.0typ (Io=100%) 50/60 (47 - 63) or DC 82typ (Io=100%) 83typ (Io=100%) 84typ (Io=100%) 85typ (Io=100%) 86typ (Io=100%) 87typ (Io=100%) 0.98typ (Io=100%) 0.93typ (Io=100%) 15typ (Io=100%) (At cold start) (Ta=25 C) 30typ (Io=100%) (At cold start) (Ta=25 C) 0.75max (60Hz, According to IEC60950 and DEN-AN) +24 +36 +48 0 - 6.3 (Peak 12) 0 - 4.2 (Peak 8) 0 - 3.2 (Peak 6) 151.2 (Peak 288) 151.2 (Peak 288) 153.6 (Peak 288) 48max 48max 48max 76max 90max 150max 120max 120max 150max 160max 160max 300max 150max 150max 250max 180max 180max 350max 120max 150max 240max 145max 180max 300max 48max 48max 48max 500max (ACIN 100V, Io=100%) 20typ (ACIN 100V, Io=100%) 21.4 - 26.4 26.4 - 39.6 39.6 - 52.8 23.0 - 25.0 35.0 - 37.0 46.0 - 50.0 Works over 101% of peak current and recovers automatically Works at 115 - 140% of rating Option (Refer to Instruction Manual) AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC500V 1minute, Cutoff current = 100mA, DC500V 50MW min (At Room Temperature) AC100V 1minute, Cutoff current = 100mA, DC100V 10MW min (At Room Temperature) -10 to +70C, 20 - 90%RH (Non condensing) (Refer to DERATING CURVE), 3,000m (10,000feet) max -20 to +75C, 20 - 90%RH (Non condensing), 9,000m (30,000feet) max 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axis 196.1m/s2 (20G), 11ms, once each X, Y and Z axis UL60950-1, C-UL(CSA60950-1), EN60950-1, EN60065, EN50178 Complies with DEN-AN and IEC60950-1 (At only AC input) Complies with FCC-B, CISPR22-B, EN55022-B, VCCI-B Complies with IEC61000-3-2 *7 85X40X222mm [3.35X1.57X8.74 inches] (W XHXD) /490g max (with chassis & cover : 830g max) Convection *1Specification is changed at option, refer to Instruction Manual 6. *2Peak loading for 10sec. And Duty 35% max, refer to Instruction Manual 5. In detail. *3This is the value that measured on measuring board with capacitor of 22mF within 150mm from output terminal.Measured by 20MHz oscilloscope or Ripple-Noise meter (Equivalent to KEISOKU-GIKEN: RM101). *4Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C, with the input voltage held constant at the rated input/output. LEP-4 *5Applicable when remote control (optional) is added. *6Please contact us about safety approvals for the model with option. *7Please contact us about class C. *Parallel operation with other model is not possible. *Derating is required when operated with chassis and cover. *A sound may occur from power supply at peak loading. LEP150F External view 235-+0.5 Voltage adjust 3.5-4.0 [0.14-0.16] Mounting Hole Connector for -Z (option) 47 95 4.5 [0.18] 252 [9.92] 4.5 235-+0.5 [0.18] 8 [9.25] 2-M4 [0.31] 4.5 [0.18] CN4 CN3 25 [1.46] 37 Mounting Hole [0.12](Lead) 3max RC(-) RC(+) + COM - PCB t=1.6 [0.06] PIN CONNECTION CN1 Pin No. Input 1 AC(L) 2 AC(N) 3 4 FG 5 51 222 [8.74] CN3 [2.01] [8.35] CN4 [0.98] [0.59] 212 -+ 0.5 I / O Connector Mating Connector Terminal Chain : SVH-21T-P1.1 CN1 VHR-5N B3P5-VH Loose: BVH-21T-P1.1 Chain : SVH-21T-P1.1 CN2 VHR-8N B8P-VH Loose: BVH-21T-P1.1 Chain : SXH-001T-P0.6 CN3 XHP-2 B2B-XH-A (Option) Loose: BXH-001T-P0.6 Chain : SXH-001T-P0.6 CN4 XHP-3 B3B-XH-A (Option) Loose: BXH-001T-P0.6 (Mfr: J.S.T.) [1.85] 20 [1.18] [1.38] 35-+0.5 Connector for Remote ON/OFF (option) 105 -+ 0.5 [4.13] 15 [0.2] CN1 CN3 CN4 5 55-+0.5 CN2 1 4 5 8 (68) -V +V 5 30 CN2 C119 [2.68] [2.95] 85 75 -+0.5 [3.35] CN1 [0.2] 4-M4 Mounting Hole [0.18] [3.74] Mounting Hole [8.46] 5 FG 3 Input(N) 1 Input(L) 8 [0.31] 2-4.5 [0.79] (215) [2.16] Name plate [9.25] 4-3.5 [0.14] CN2 Pin No. Output 1, 2, 3, 4 -V 5, 6, 7, 8 +V CN3 (Option) Pin No. Remote ON/OFF 1 RC(+) 2 RC(-) Weight: 490g max (with chassis & cover : 830g max) Tolerance: t1 [t0.04] Dimensions in mm, [ ]=inches PCB Material : CEM3 Chassis and cover is optional. Mounting torque: 1.5N * m(16kgf * cm)max CN4 (Option) Pin No. -Z 1 + COM 2 3 Keep drawing current per pin below 5A(7A at peak load)for CN2 Performance data RISE TIME & FALL TIME (LEP150F-24) EFFICIENCY (LEP150F-24) 88 86 ACIN 100V Io=100% EFFICIENCY 84 DC Output 82 80 AC Input 78 100ms/DIV 76 60 20ms/DIV INPUT HARMONIC CURRENT (LEP150F-24) 140 180 220 260 300 V INPUT HARMONIC CURRENT (LEP150F-24) 10 HARMONIC CURRENT Load factor 100% Input voltage AC 100V 1 0.1 0.01 10 20 HARMONIC ORDER 30 Harmonic current standard class A (at odd number) A Harmonic current standard class A (at odd number) A HARMONIC CURRENT 100 INPUT VOLTAGE 10 0.001 0 Load factor100% Load factor 50% 40 1 Load factor 100% Input voltage AC 230V 0.1 0.01 0.001 0 10 20 30 40 HARMONIC ORDER LEP-5 AC-DC Power Supplies Open Frame/ Enclosed Type LEP240F Ordering information LEP 240 1 2 F 3 -24 4 Example recommended EMI/EMC filter NAC-06-472 R High voltage pulse noise type : NAP series Low leakage current type : NAM series * A higher current rating EMI/EMC filter may be recommended in view of the other devices that could be connected in parallel with the power supply. -O 5 1Series name 2Output wattage 3Universal input 4Output voltage 5Optional *1 *6 G :Low leakage current R :with Remote ON/OFF S :with Chassis SN:with Chassis & cover T :Vertical terminal block U :Operating stop voltage is set at a lower value Z :with ZT *Make sure necessary tests will be carried out on your end equipment with the power supply installed in accordance with any required EMC/EMI regulations. MODEL DC OUTPUT LEP240F-24 +24V 10(Peak 20)A LEP240F-36 +36V 6.7(Peak 13.4)A LEP240F-48 +48V 5(Peak 10)A SPECIFICATIONS MODEL VOLTAGE[V] CURRENT[A] ACIN 100V ACIN 200V FREQUENCY[Hz] INPUT OUTPUT PROTECTION CIRCUIT AND OTHERS ISOLATION ENVIRONMENT SAFETY AND NOISE REGULATIONS OTHERS ACIN 100V ACIN 200V ACIN 100V POWER FACTOR ACIN 200V ACIN 100V INRUSH CURRENT[A] ACIN 200V LEAKAGE CURRENT[mA] VOLTAGE[V] CURRENT[A] *2 WATTAGE[W] LINE REGULATION[mV] LOAD REGULATION[mV] 0 to +40C *3 RIPPLE[mVp-p] -10 - 0C *3 0 to +40C *3 RIPPLE NOISE[mVp-p] -10 - 0C *3 0 to +40C TEMPERATURE REGULATION[mV] -10 to +40C DRIFT[mV] *4 START-UP TIME[ms] HOLD-UP TIME[ms] OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V] OVERCURRENT PROTECTION OVERVOLTAGE PROTECTION REMOTE ON/OFF INPUT-OUTPUT -RC *5 INPUT-FG OUTPUT-RC-FG *5 OUTPUT-RC *5 OPERATING TEMP.,HUMID.AND ALTITUDE STORAGE TEMP.,HUMID.AND ALTITUDE VIBRATION IMPACT AGENCY APPROVALS CONDUCTED NOISE HARMONIC ATTENUATOR CASE SIZE/WEIGHT COOLING METHOD EFFICIENCY[%] LEP240F-24 LEP240F-36 LEP240F-48 AC85 - 264 1f or DC 120 - 370 3.3typ (Io=100%) 1.7typ (Io=100%) 50/60 (47 - 63) or DC 83typ (Io=100%) 84typ (Io=100%) 84typ (Io=100%) 86typ (Io=100%) 87typ (Io=100%) 87typ (Io=100%) 0.98typ (Io=100%) 0.93typ (Io=100%) 15typ (Io=100%) (More than 3sec.to re-start) 30typ (Io=100%) (More than 3sec.to re-start) 0.75max (60Hz, According to IEC60950 and DEN-AN) +24 +36 +48 0 - 10 (Peak 20) 0 - 6.7 (Peak 13.4) 0 - 5 (Peak 10) 240.0 (Peak 480) 241.2 (Peak 482.4) 240.0 (Peak 480) 48max 48max 48max 76max 90max 150max 120max 120max 150max 160max 160max 300max 150max 150max 250max 180max 180max 350max 120max 150max 240max 145max 180max 300max 48max 48max 48max 500max (ACIN 100V, Io=100%) 20typ (ACIN 100V, Io=100%) 21.4 - 26.4 26.4 - 39.6 39.6 - 52.8 23.0 - 25.0 35.0 - 37.0 46.0 - 50.0 Works over 101% of peak current and recovers automatically Works at 115 - 140% of rating Option (Refer to Instruction Manual) AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC500V 1minute, Cutoff current = 100mA, DC500V 50MW min (At Room Temperature) AC100V 1minute, Cutoff current = 100mA, DC100V 10MW min (At Room Temperature) -10 to +70C, 20 - 90%RH (Non condensing) (Refer to DERATING CURVE), 3,000m (10,000feet) max -20 to +75C, 20 - 90%RH (Non condensing), 9,000m (30,000feet) max 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axis 196.1m/s2 (20G), 11ms, once each X, Y and Z axis UL60950-1, C-UL(CSA60950-1), EN60950-1, EN60065, EN50178 Complies with DEN-AN and IEC60950-1 (At only AC input) Complies with FCC-B, CISPR22-B, EN55022-B, VCCI-B Complies with IEC61000-3-2 *7 95X45X222mm [3.74X1.77X8.74 inches] (WXHXD) /690g max (with chassis & cover : 1,070g max) Convection *1Specification is changed at option, refer to Instruction Manual 6. *2Peak loading for 10sec. And Duty 35% max, refer to Instruction Manual 5. In detail. *3This is the value that measured on measuring board with capacitor of 22mF within 150mm from output terminal.Measured by 20MHz oscilloscope or Ripple-Noise meter (Equivalent to KEISOKU-GIKEN: RM101). *4Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C, with the input voltage held constant at the rated input/output. LEP-6 *5Applicable when remote control (optional) is added. *6Please contact us about safety approvals for the model with option. *7Please contact us about class C. *Parallel operation with other model is not possible. *Derating is required when operated with chassis and cover. *A sound may occur from power supply at peak loading. LEP240F External view 235-+0.5 Voltage adjust 52 33 [2.05] 4.5 [4.25] CN2 108 CN1 [0.18] 8 [1.77] 65-+0.5 +V 4-M4 Mounting Hole [0.31] 1 4 5 [2.56] -V (66) CN2 [2.6] C119 [3.35] 95 [3.74] 85-+0.5 CN1 5 FG 3 Input(N) 1 Input(L) 8 [9.25] [1.3] 23 [8.39] [0.91] 2-4.5 [0.18] 4-3.5 [0.14] Mounting Hole (213) 45-+0.5 Name plate CN3 Connector for Remote ON/OFF (option) [0.31] 3max [0.12](Lead) RC(-) I / O Connector Mating Connector Terminal Chain : SVH-21T-P1.1 CN1 VHR-5N B3P5-VH Loose: BVH-21T-P1.1 Chain : SVH-21T-P1.1 CN2 VHR-8N B8P-VH Loose: BVH-21T-P1.1 Chain : SXH-001T-P0.6 CN3 XHP-2 B2B-XH-A (Option) Loose: BXH-001T-P0.6 Chain : SXH-001T-P0.6 CN4 XHP-3 B3B-XH-A (Option) Loose: BXH-001T-P0.6 (Mfr: J.S.T.) RC(+) + COM - PCB t=1.6 [0.06] CN1 Pin No. Input 1 AC(L) 2 3 AC(N) 4 5 FG PIN CONNECTION CN2 Pin No. Output 1, 2, 3, 4 -V 5, 6, 7, 8 +V CN3 (Option) Pin No. Remote ON/OFF 1 RC(+) 2 RC(-) CN4 (Option) Pin No. -Z 1 + COM 2 3 58 CN3 [2.28] CN4 8 [9.25] [0.59] [1.65] [8.74] 252 [9.92] 235-+0.5 4.5 [0.18] 2-M4 Mounting Hole [1.18] Connector for -Z (option) 222 CN3 15 [8.35] 42 CN4 3.5-4.0 [0.14-0.16] Mounting Hole 212 -+ 0.5 4.5 [4.88] [0.18] 124 -+ 0.5 5 [0.2] 30 [0.2] 5 CN4 Weight: 690g max (with chassis & cover : 1,070g max) Tolerance: t1 [t0.04] Dimensions in mm, [ ]=inches PCB Material : CEM3 Chassis and cover is optional. Mounting torque: 1.5N * m(16kgf * cm)max Keep drawing current per pin below 5A(7A at peak load)for CN2 Performance data RISE TIME & FALL TIME (LEP240F-24) EFFICIENCY (LEP240F-24) 88 ACIN 100V Io=100% EFFICIENCY 86 DC Output AC Input 78 60 20ms/DIV INPUT HARMONIC CURRENT (LEP240F-24) Load factor100% Load factor 50% 160 110 210 INPUT VOLTAGE 260 310 V INPUT HARMONIC CURRENT (LEP240F-24) 10 10 HARMONIC CURRENT Load factor 100% Input voltage AC 100V 1 0.1 0.01 10 20 HARMONIC ORDER 30 Harmonic current standard class A (at odd number) A Harmonic current standard class A (at odd number) A HARMONIC CURRENT 82 80 100ms/DIV 0.001 0 84 40 1 Load factor 100% Input voltage AC 230V 0.1 0.01 0.001 0 10 20 30 40 HARMONIC ORDER LEP-7